CODA timeout and macroblock error control
v3 cover CODA timeout and macroblock error control
Hi all,
I'm sending here the patches that are pending in previous series [2].
The main motivation for this fix is to address a PIC_RUN timeout, which we managed to link with a hardware bitstream buffer underrun condition.
Upon further investigation we discovered that the underrun was produced by a subtle issue in the way buffer_meta's were being tracked.
The issue is fixed by patch "1/2 coda: coda_buffer_meta housekeeping fix".
Also, while testing with corrupted bitstreams we realized the driver was logging too verbosely, so patch 2 addresses this by introducing a private control to read an macroblock-error counter.
These patches have been tested against media's upstream and v5.4-based, on i.MX6 (Wandboard) with H.264 and MPEG-2 streams.
As reported by Benjamin Bara this fix is not sufficient to fix all timeouts. However, the fix does help to fix some of the cases.
For instance, videos containing small black frames, are now fixed. See:
gst-launch-1.0 videotestsrc pattern=black num-buffers=300 ! \
video/x-raw,format=I420,width=176,height=120 ! avenc_mpeg2video ! \
mpegvideoparse ! mpegtsmux ! filesink location=black-qcif-10s.ts
Reviews and feedback are appreciated, as always.
[1] https://lkml.org/lkml/2020/8/21/495
[2] https://patchwork.linuxtv.org/project/linux-media/list/?series=3592
Changelog
---------
v3:
* Address Hans' feedback on patch 2.
In particular, the control is not marked as volatile, since that was incorrect.
Also, move the control CID definition inside the driver header.
v2:
* Keep the error MB message, but move it to coda_dbg(1, ctx).
* Add per-device rate limitting for the error MB message.
* Rename V4L2_CID_CODA_ERR_MB description.
* s/__coda_decoder_drop_used_metas/coda_decoder_drop_used_metas
Ezequiel Garcia (2):
coda: coda_buffer_meta housekeeping fix
coda: Add a V4L2 user for control error macroblocks count
drivers/media/platform/coda/coda-bit.c | 52 ++++++++++++++++++++--- drivers/media/platform/coda/coda-common.c | 18 ++++++++ drivers/media/platform/coda/coda.h | 11 +++++ include/uapi/linux/v4l2-controls.h | 4 ++ 4 files changed, 78 insertions(+), 7 deletions(-)
Signature · 1 line
2.27.0
PATCH v3 1/2 coda: coda_buffer_meta housekeeping fix
It's possible that the VPU was initialized using just one buffer, containing only codec headers.
In this case, right after the initialization and after updating the FIFO read pointer, we need to iterate through all the coda_buffer_meta and release any metas that have been already used by the VPU.
This issue is affecting indirectly the bitstream buffer fill threshold, which depends on the meta end position of the first queued meta, which is passed to coda_bitstream_can_fetch_past().
Without this fix, it's possible that for certain videos, the bitstream buffer level is not filled properly, resulting in a PIC_RUN timeout.
--- drivers/media/platform/coda/coda-bit.c | 42 +++++++++++++++++++++++--- drivers/media/platform/coda/coda.h | 1 + 2 files changed, 39 insertions(+), 4 deletions(-)
drivers/media/platform/coda/coda-bit.c +38 -4
@@ -1836,6 +1836,29 @@ static bool coda_reorder_enable(struct coda_ctx *ctx)return profile >V4L2_MPEG_VIDEO_H264_PROFILE_BASELINE ; } +static void coda_decoder_drop_used_metas (struct coda_ctx *ctx) +{ +struct coda_buffer_meta *meta, *tmp; + +/* +* All metas that end at or before the RD pointer (fifo out), +* are now consumed by the VPU and should be released. +*/ +spin_lock (&ctx->buffer_meta_lock); +list_for_each_entry_safe (meta, tmp, &ctx->buffer_meta_list, list) { +if (ctx->bitstream_fifo.kfifo.out >= meta->end) { +coda_dbg (2 , ctx,"releasing meta: seq=%d start=%d end=%d\n" , + meta->sequence, meta->start, meta->end); + +list_del (&meta->list); + ctx->num_metas--; + ctx->first_frame_sequence++; +kfree (meta); + } + } +spin_unlock (&ctx->buffer_meta_lock); +} +static int __coda_decoder_seq_init (struct coda_ctx *ctx) {struct coda_q_data *q_data_src, *q_data_dst;
@@ -1921,10 +1944,17 @@ static int __coda_decoder_seq_init(struct coda_ctx *ctx) } ctx->sequence_offset = ~0U ; ctx->initialized =1 ; + ctx->first_frame_sequence =0 ;/* Update kfifo out pointer from coda bitstream read pointer */ coda_kfifo_sync_from_device (ctx); +/* +* After updating the read pointer, we need to check if +* any metas are consumed and should be released. +*/ +coda_decoder_drop_used_metas (ctx); +if (coda_read (dev,CODA_RET_DEC_SEQ_SUCCESS ) ==0 ) { v4l2_err(&dev->v4l2_dev, "CODA_COMMAND_SEQ_INIT failed, error code = 0x%x\n",
@@ -2395,12 +2425,16 @@ static void coda_finish_decode(struct coda_ctx *ctx)v4l2_err (&dev->v4l2_dev,"decoded frame index out of range: %d\n" , decoded_idx); }else { +int sequence; + decoded_frame = &ctx->internal_frames[decoded_idx]; val =coda_read (dev,CODA_RET_DEC_PIC_FRAME_NUM );if (ctx->sequence_offset ==-1 ) ctx->sequence_offset = val; - val -= ctx->sequence_offset; + + sequence = val + ctx->first_frame_sequence + - ctx->sequence_offset;spin_lock (&ctx->buffer_meta_lock);if (!list_empty (&ctx->buffer_meta_list)) { meta = list_first_entry(&ctx->buffer_meta_list,
@@ -2415,10 +2449,10 @@ static void coda_finish_decode(struct coda_ctx *ctx)* should be enough to detect most errors and saves us * from doing different things based on the format. */ -if ((val &0xffff ) != (meta->sequence &0xffff )) { +if ((sequence &0xffff ) != (meta->sequence &0xffff )) {v4l2_err (&dev->v4l2_dev,"sequence number mismatch (%d(%d) != %d)\n" , - val, ctx->sequence_offset, + sequence, ctx->sequence_offset, meta->sequence); } decoded_frame->meta = *meta;
@@ -2428,7 +2462,7 @@ static void coda_finish_decode(struct coda_ctx *ctx)v4l2_err (&dev->v4l2_dev,"empty timestamp list!\n" );memset (&decoded_frame->meta,0 ,sizeof (struct coda_buffer_meta )); - decoded_frame->meta.sequence = val; + decoded_frame->meta.sequence = sequence; decoded_frame->meta.last = false; ctx->sequence_offset++; }
drivers/media/platform/coda/coda.h +1 -0
@@ -259,6 +259,7 @@ struct coda_ctx {struct list_head buffer_meta_list;spinlock_t buffer_meta_lock;int num_metas; +unsigned int first_frame_sequence;struct coda_aux_buf workbuf;int num_internal_frames;int idx;
Signature · 1 line
2.27.0
PATCH v3 2/2 coda: Add a V4L2 user for control error macroblocks count
In reply to Ezequiel GarciaTo avoid potentially overflowing the kernel logs in the case of corrupted streams, this commit replaces an error message with a per-stream counter to be read through a driver-specific control.
Applications can read the per-stream accumulated
error macroblocks count.
The old error message is replaced by a rate-limited debug message.
--- drivers/media/platform/coda/coda-bit.c | 10 +++++++--- drivers/media/platform/coda/coda-common.c | 18 ++++++++++++++++++ drivers/media/platform/coda/coda.h | 10 ++++++++++ include/uapi/linux/v4l2-controls.h | 4 ++++ 4 files changed, 39 insertions(+), 3 deletions(-)
drivers/media/platform/coda/coda-bit.c +7 -3
@@ -13,6 +13,7 @@#include <linux/kernel.h> #include <linux/log2.h> #include <linux/platform_device.h> +#include <linux/ratelimit.h> #include <linux/reset.h> #include <linux/slab.h> #include <linux/videodev2.h>
@@ -2369,9 +2370,12 @@ static void coda_finish_decode(struct coda_ctx *ctx) } err_mb =coda_read (dev,CODA_RET_DEC_PIC_ERR_MB ); -if (err_mb >0 ) -v4l2_err (&dev->v4l2_dev, -"errors in %d macroblocks\n" , err_mb); +if (err_mb >0 ) { +if (__ratelimit (&dev->err_mb_rs)) +coda_dbg (1 , ctx,"errors in %d macroblocks\n" , err_mb); +v4l2_ctrl_s_ctrl (ctx->err_mb_ctrl, +v4l2_ctrl_g_ctrl (ctx->err_mb_ctrl) + err_mb); + }if (dev->devtype->product ==CODA_HX4 || dev->devtype->product ==CODA_7541 ) {
drivers/media/platform/coda/coda-common.c +18 -0
@@ -26,6 +26,7 @@#include <linux/videodev2.h> #include <linux/of.h> #include <linux/platform_data/media/coda.h> +#include <linux/ratelimit.h> #include <linux/reset.h> #include <media/v4l2-ctrls.h>
@@ -2062,6 +2063,7 @@ static int coda_start_streaming(struct vb2_queue *q, unsigned int count)if (q_data_dst->fourcc ==V4L2_PIX_FMT_JPEG ) ctx->params.gop_size =1 ; ctx->gopcounter = ctx->params.gop_size -1 ; +v4l2_ctrl_s_ctrl (ctx->err_mb_ctrl,0 ); ret = ctx->ops->start_streaming (ctx);if (ctx->inst_type ==CODA_INST_DECODER ) {
@@ -2462,6 +2464,15 @@ static void coda_decode_ctrls(struct coda_ctx *ctx) ctx->mpeg4_level_ctrl->flags |=V4L2_CTRL_FLAG_READ_ONLY ; } +static const struct v4l2_ctrl_config coda_err_mb_ctrl_config = { + .id =V4L2_CID_CODA_MB_ERR_CNT , + .name ="Macroblocks Error Count" , + .type =V4L2_CTRL_TYPE_INTEGER , + .min =0 , + .max =0x7fffffff , + .step =1 , +}; +static int coda_ctrls_setup (struct coda_ctx *ctx) {v4l2_ctrl_handler_init (&ctx->ctrls,2 );
@@ -2484,6 +2495,12 @@ static int coda_ctrls_setup(struct coda_ctx *ctx) 1, 1, 1, 1);if (ctx->cvd->src_formats[0 ] ==V4L2_PIX_FMT_H264 )coda_decode_ctrls (ctx); + + ctx->err_mb_ctrl =v4l2_ctrl_new_custom (&ctx->ctrls, + &coda_err_mb_ctrl_config, +NULL ); +if (ctx->err_mb_ctrl) + ctx->err_mb_ctrl->flags |=V4L2_CTRL_FLAG_READ_ONLY ; }if (ctx->ctrls.error) {
@@ -3202,6 +3219,7 @@ static int coda_probe(struct platform_device *pdev)if (ret)return ret; +ratelimit_default_init (&dev->err_mb_rs);mutex_init (&dev->dev_mutex);mutex_init (&dev->coda_mutex);ida_init (&dev->ida);
drivers/media/platform/coda/coda.h +10 -0
@@ -17,6 +17,7 @@#include <linux/mutex.h> #include <linux/kfifo.h> #include <linux/videodev2.h> +#include <linux/ratelimit.h> #include <media/v4l2-ctrls.h> #include <media/v4l2-device.h>
@@ -28,6 +29,13 @@#define CODA_MAX_FRAMEBUFFERS 19#define FMO_SLICE_SAVE_BUF_SIZE (32) +/* +* This control allows aplications to read the per-stream +* (i.e. per-context) Macroblocks Error Count. This value +* is CODA specific. +*/ +#define V4L2_CID_CODA_MB_ERR_CNT (V4L2_CID_USER_CODA_BASE + 0) +enum {V4L2_M2M_SRC =0 ,V4L2_M2M_DST =1 ,
@@ -92,6 +100,7 @@ struct coda_dev {struct v4l2_m2m_dev *m2m_dev;struct ida ida;struct dentry *debugfs_root; +struct ratelimit_state err_mb_rs; };struct coda_codec {
@@ -242,6 +251,7 @@ struct coda_ctx {struct v4l2_ctrl *mpeg2_level_ctrl;struct v4l2_ctrl *mpeg4_profile_ctrl;struct v4l2_ctrl *mpeg4_level_ctrl; +struct v4l2_ctrl *err_mb_ctrl;struct v4l2_fh fh;int gopcounter;int runcounter;
include/uapi/linux/v4l2-controls.h +4 -0
@@ -198,6 +198,10 @@ enum v4l2_colorfx {*/ #define V4L2_CID_USER_ATMEL_ISC_BASE (V4L2_CID_USER_BASE + 0x10c0) +/* The base for the CODA driver controls. +* We reserve 16 controls for this driver. */ +#define V4L2_CID_USER_CODA_BASE (V4L2_CID_USER_BASE + 0x10e0) +/* MPEG-class control IDs */ /* The MPEG controls are applicable to all codec controls * and the 'MPEG' part of the define is historical */
Signature · 1 line
2.27.0
Re: [PATCH v3 2/2] coda: Add a V4L2 user for control error macroblocks count
Hi Ezequiel,
Some more (small) comments:
Quoted 67 lines · Ezequiel Garcia
To avoid potentially overflowing the kernel logs in the case of corrupted streams, this commit replaces an error message with a per-stream counter to be read through a driver-specific control.
Applications can read the per-stream accumulated
error macroblocks count.The old error message is replaced by a rate-limited debug message.
Signed-off-by Ezequiel Garcia <[email protected]>--- drivers/media/platform/coda/coda-bit.c | 10 +++++++--- drivers/media/platform/coda/coda-common.c | 18 ++++++++++++++++++ drivers/media/platform/coda/coda.h | 10 ++++++++++ include/uapi/linux/v4l2-controls.h | 4 ++++ 4 files changed, 39 insertions(+), 3 deletions(-)drivers/media/platform/coda/coda-bit.c +7
-3@@ -13,6 +13,7 @@#include <linux/kernel.h> #include <linux/log2.h> #include <linux/platform_device.h> +#include <linux/ratelimit.h> #include <linux/reset.h> #include <linux/slab.h> #include <linux/videodev2.h> @@ -2369,9 +2370,12 @@ static void coda_finish_decode(struct coda_ctx *ctx) } err_mb =coda_read (dev,CODA_RET_DEC_PIC_ERR_MB ); -if (err_mb >0 ) -v4l2_err (&dev->v4l2_dev, -"errors in %d macroblocks\n" , err_mb); +if (err_mb >0 ) { +if (__ratelimit (&dev->err_mb_rs)) +coda_dbg (1 , ctx,"errors in %d macroblocks\n" , err_mb); +v4l2_ctrl_s_ctrl (ctx->err_mb_ctrl, +v4l2_ctrl_g_ctrl (ctx->err_mb_ctrl) + err_mb); + }if (dev->devtype->product ==CODA_HX4 || dev->devtype->product ==CODA_7541 ) {drivers/media/platform/coda/coda-common.c +2
-0@@ -26,6 +26,7 @@#include <linux/videodev2.h> #include <linux/of.h> #include <linux/platform_data/media/coda.h> +#include <linux/ratelimit.h> #include <linux/reset.h> #include <media/v4l2-ctrls.h> @@ -2062,6 +2063,7 @@ static int coda_start_streaming(struct vb2_queue *q, unsigned int count)if (q_data_dst->fourcc ==V4L2_PIX_FMT_JPEG ) ctx->params.gop_size =1 ; ctx->gopcounter = ctx->params.gop_size -1 ; +v4l2_ctrl_s_ctrl (ctx->err_mb_ctrl,0 ); ret = ctx->ops->start_streaming (ctx);if (ctx->inst_type ==CODA_INST_DECODER ) {
drivers/media/platform/coda/coda-common.c static void coda_decode_ctrls(struct coda_ctx *ctx) · line 2467
Quoted 4 lines
drivers/media/platform/coda/coda-common.c +1
-0@@ -2462,6 +2464,15 @@ static void coda_decode_ctrls(struct coda_ctx *ctx) ctx->mpeg4_level_ctrl->flags |=V4L2_CTRL_FLAG_READ_ONLY ; } +static const struct v4l2_ctrl_config coda_err_mb_ctrl_config = {
Please also update this struct name to coda_mb_err_cnt_ctrl_config.
Quoted 12 lines
drivers/media/platform/coda/coda-common.c +8
-0+ .id = V4L2_CID_CODA_MB_ERR_CNT, + .name = "Macroblocks Error Count", + .type = V4L2_CTRL_TYPE_INTEGER, + .min = 0, + .max = 0x7fffffff, + .step = 1, +}; +static int coda_ctrls_setup (struct coda_ctx *ctx) {v4l2_ctrl_handler_init (&ctx->ctrls,2 );
drivers/media/platform/coda/coda-common.c static int coda_ctrls_setup(struct coda_ctx *ctx) · line 2499
Quoted 5 lines
drivers/media/platform/coda/coda-common.c +2
-0@@ -2484,6 +2495,12 @@ static int coda_ctrls_setup(struct coda_ctx *ctx) 1, 1, 1, 1);if (ctx->cvd->src_formats[0 ] ==V4L2_PIX_FMT_H264 )coda_decode_ctrls (ctx); + + ctx->err_mb_ctrl = v4l2_ctrl_new_custom(&ctx->ctrls,
And this to mb_err_cnt_ctrl. This keeps the naming consistent.
Quoted 28 lines
drivers/media/platform/coda/coda-common.c +5
-0+ &coda_err_mb_ctrl_config, + NULL); +if (ctx->err_mb_ctrl) + ctx->err_mb_ctrl->flags |=V4L2_CTRL_FLAG_READ_ONLY ; }if (ctx->ctrls.error) {@@ -3202,6 +3219,7 @@ static int coda_probe(struct platform_device *pdev)if (ret)return ret; +ratelimit_default_init (&dev->err_mb_rs);mutex_init (&dev->dev_mutex);mutex_init (&dev->coda_mutex);ida_init (&dev->ida);drivers/media/platform/coda/coda.h +1
-0@@ -17,6 +17,7 @@#include <linux/mutex.h> #include <linux/kfifo.h> #include <linux/videodev2.h> +#include <linux/ratelimit.h> #include <media/v4l2-ctrls.h> #include <media/v4l2-device.h>
drivers/media/platform/coda/coda.h line 33
Quoted 5 lines
drivers/media/platform/coda/coda.h +2
-0@@ -28,6 +29,13 @@#define CODA_MAX_FRAMEBUFFERS 19#define FMO_SLICE_SAVE_BUF_SIZE (32) +/* +* This control allows aplications to read the per-stream
Typo: applications
Quoted 30 lines
drivers/media/platform/coda/coda.h +7
-0+* (i.e. per-context) Macroblocks Error Count. This value +* is CODA specific. +*/ +#define V4L2_CID_CODA_MB_ERR_CNT (V4L2_CID_USER_CODA_BASE + 0) +enum {V4L2_M2M_SRC =0 ,V4L2_M2M_DST =1 ,@@ -92,6 +100,7 @@ struct coda_dev {struct v4l2_m2m_dev *m2m_dev;struct ida ida;struct dentry *debugfs_root; +struct ratelimit_state err_mb_rs; };struct coda_codec {@@ -242,6 +251,7 @@ struct coda_ctx {struct v4l2_ctrl *mpeg2_level_ctrl;struct v4l2_ctrl *mpeg4_profile_ctrl;struct v4l2_ctrl *mpeg4_level_ctrl; +struct v4l2_ctrl *err_mb_ctrl;struct v4l2_fh fh;int gopcounter;int runcounter;include/uapi/linux/v4l2-controls.h +0
-0
include/uapi/linux/v4l2-controls.h enum v4l2_colorfx { · line 207
Quoted 10 lines
include/uapi/linux/v4l2-controls.h +4
-0@@ -198,6 +198,10 @@ enum v4l2_colorfx {*/ #define V4L2_CID_USER_ATMEL_ISC_BASE (V4L2_CID_USER_BASE + 0x10c0) +/* The base for the CODA driver controls. +* We reserve 16 controls for this driver. */ +#define V4L2_CID_USER_CODA_BASE (V4L2_CID_USER_BASE + 0x10e0) +/* MPEG-class control IDs */ /* The MPEG controls are applicable to all codec controls * and the 'MPEG' part of the define is historical */
Regards,
Hans
PATCH v4 1/1 coda: Add a V4L2 user for control error macroblocks count
In reply to Ezequiel GarciaTo avoid potentially overflowing the kernel logs in the case of corrupted streams, this commit replaces an error message with a per-stream counter to be read through a driver-specific control.
Applications can read the per-stream accumulated
error macroblocks count.
The old error message is replaced by a rate-limited debug message.
--- drivers/media/platform/coda/coda-bit.c | 10 +++++++--- drivers/media/platform/coda/coda-common.c | 18 ++++++++++++++++++ drivers/media/platform/coda/coda.h | 10 ++++++++++ include/uapi/linux/v4l2-controls.h | 4 ++++ 4 files changed, 39 insertions(+), 3 deletions(-)
drivers/media/platform/coda/coda-bit.c +7 -3
@@ -13,6 +13,7 @@#include <linux/kernel.h> #include <linux/log2.h> #include <linux/platform_device.h> +#include <linux/ratelimit.h> #include <linux/reset.h> #include <linux/slab.h> #include <linux/videodev2.h>
@@ -2369,9 +2370,12 @@ static void coda_finish_decode(struct coda_ctx *ctx) } err_mb =coda_read (dev,CODA_RET_DEC_PIC_ERR_MB ); -if (err_mb >0 ) -v4l2_err (&dev->v4l2_dev, -"errors in %d macroblocks\n" , err_mb); +if (err_mb >0 ) { +if (__ratelimit (&dev->mb_err_rs)) +coda_dbg (1 , ctx,"errors in %d macroblocks\n" , err_mb); +v4l2_ctrl_s_ctrl (ctx->mb_err_cnt_ctrl, +v4l2_ctrl_g_ctrl (ctx->mb_err_cnt_ctrl) + err_mb); + }if (dev->devtype->product ==CODA_HX4 || dev->devtype->product ==CODA_7541 ) {
drivers/media/platform/coda/coda-common.c +18 -0
@@ -26,6 +26,7 @@#include <linux/videodev2.h> #include <linux/of.h> #include <linux/platform_data/media/coda.h> +#include <linux/ratelimit.h> #include <linux/reset.h> #include <media/v4l2-ctrls.h>
@@ -2062,6 +2063,7 @@ static int coda_start_streaming(struct vb2_queue *q, unsigned int count)if (q_data_dst->fourcc ==V4L2_PIX_FMT_JPEG ) ctx->params.gop_size =1 ; ctx->gopcounter = ctx->params.gop_size -1 ; +v4l2_ctrl_s_ctrl (ctx->mb_err_cnt_ctrl,0 ); ret = ctx->ops->start_streaming (ctx);if (ctx->inst_type ==CODA_INST_DECODER ) {
@@ -2462,6 +2464,15 @@ static void coda_decode_ctrls(struct coda_ctx *ctx) ctx->mpeg4_level_ctrl->flags |=V4L2_CTRL_FLAG_READ_ONLY ; } +static const struct v4l2_ctrl_config coda_mb_err_cnt_ctrl_config = { + .id =V4L2_CID_CODA_MB_ERR_CNT , + .name ="Macroblocks Error Count" , + .type =V4L2_CTRL_TYPE_INTEGER , + .min =0 , + .max =0x7fffffff , + .step =1 , +}; +static int coda_ctrls_setup (struct coda_ctx *ctx) {v4l2_ctrl_handler_init (&ctx->ctrls,2 );
@@ -2484,6 +2495,12 @@ static int coda_ctrls_setup(struct coda_ctx *ctx) 1, 1, 1, 1);if (ctx->cvd->src_formats[0 ] ==V4L2_PIX_FMT_H264 )coda_decode_ctrls (ctx); + + ctx->mb_err_cnt_ctrl =v4l2_ctrl_new_custom (&ctx->ctrls, + &coda_mb_err_cnt_ctrl_config, +NULL ); +if (ctx->mb_err_cnt_ctrl) + ctx->mb_err_cnt_ctrl->flags |=V4L2_CTRL_FLAG_READ_ONLY ; }if (ctx->ctrls.error) {
@@ -3202,6 +3219,7 @@ static int coda_probe(struct platform_device *pdev)if (ret)return ret; +ratelimit_default_init (&dev->mb_err_rs);mutex_init (&dev->dev_mutex);mutex_init (&dev->coda_mutex);ida_init (&dev->ida);
drivers/media/platform/coda/coda.h +10 -0
@@ -17,6 +17,7 @@#include <linux/mutex.h> #include <linux/kfifo.h> #include <linux/videodev2.h> +#include <linux/ratelimit.h> #include <media/v4l2-ctrls.h> #include <media/v4l2-device.h>
@@ -28,6 +29,13 @@#define CODA_MAX_FRAMEBUFFERS 19#define FMO_SLICE_SAVE_BUF_SIZE (32) +/* +* This control allows applications to read the per-stream +* (i.e. per-context) Macroblocks Error Count. This value +* is CODA specific. +*/ +#define V4L2_CID_CODA_MB_ERR_CNT (V4L2_CID_USER_CODA_BASE + 0) +enum {V4L2_M2M_SRC =0 ,V4L2_M2M_DST =1 ,
@@ -92,6 +100,7 @@ struct coda_dev {struct v4l2_m2m_dev *m2m_dev;struct ida ida;struct dentry *debugfs_root; +struct ratelimit_state mb_err_rs; };struct coda_codec {
@@ -242,6 +251,7 @@ struct coda_ctx {struct v4l2_ctrl *mpeg2_level_ctrl;struct v4l2_ctrl *mpeg4_profile_ctrl;struct v4l2_ctrl *mpeg4_level_ctrl; +struct v4l2_ctrl *mb_err_cnt_ctrl;struct v4l2_fh fh;int gopcounter;int runcounter;
include/uapi/linux/v4l2-controls.h +4 -0
@@ -198,6 +198,10 @@ enum v4l2_colorfx {*/ #define V4L2_CID_USER_ATMEL_ISC_BASE (V4L2_CID_USER_BASE + 0x10c0) +/* The base for the CODA driver controls. +* We reserve 16 controls for this driver. */ +#define V4L2_CID_USER_CODA_BASE (V4L2_CID_USER_BASE + 0x10e0) +/* MPEG-class control IDs */ /* The MPEG controls are applicable to all codec controls * and the 'MPEG' part of the define is historical */
Signature · 1 line
2.27.0