ath11k: Fix single phy hw mode
PATCH 1/1 ath11k: Fix single phy hw mode
driver not able to bootup in the single radio configured board. single phy hw mode is converted to invalid hw mode and sent to FW through wmi init cmd. In that case driver is not receiving wmi ready event which leads to driver bootup fail. single phy hw mode is a valid for single radio configured board. so removed the conversion logic.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
--- drivers/net/wireless/ath/ath11k/wmi.c | 3 --- 1 file changed, 3 deletions(-)
drivers/net/wireless/ath/ath11k/wmi.c +0 -3
@@ -3351,9 +3351,6 @@ int ath11k_wmi_cmd_init(struct ath11k_base *ab) init_param.hw_mode_id = wmi_sc->preferred_hw_mode; init_param.mem_chunks = wmi_sc->mem_chunks; -if (wmi_sc->preferred_hw_mode ==WMI_HOST_HW_MODE_SINGLE ) - init_param.hw_mode_id =WMI_HOST_HW_MODE_MAX ; -if (ab->hw_params.needs_band_to_mac) { init_param.num_band_to_mac = ab->num_radios;ath11k_fill_band_to_mac_param (ab, init_param.band_to_mac);
Signature · 1 line
2.7.4
Quoted 11 lines · Karthikeyan Periyasamy
driver not able to bootup in the single radio configured board. single phy hw mode is converted to invalid hw mode and sent to FW through wmi init cmd. In that case driver is not receiving wmi ready event which leads to driver bootup fail. single phy hw mode is a valid for single radio configured board. so removed the conversion logic.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by Karthikeyan Periyasamy <[email protected]>Signed-off-by Kalle Valo <[email protected]>
Patch applied to ath-next branch of ath.git, thanks.
9fb13b81e145 ath11k: Fix single phy hw mode
Signature · 9 lines
https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches -- ath11k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath11k
Quoted 11 lines · Karthikeyan Periyasamy
driver not able to bootup in the single radio configured board. single phy hw mode is converted to invalid hw mode and sent to FW through wmi init cmd. In that case driver is not receiving wmi ready event which leads to driver bootup fail. single phy hw mode is a valid for single radio configured board. so removed the conversion logic.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by Karthikeyan Periyasamy <[email protected]>Signed-off-by Kalle Valo <[email protected]>
Patch applied to ath-next branch of ath.git, thanks.
9fb13b81e145 ath11k: Fix single phy hw mode
Signature · 3 lines
https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches