Skip to contentSkip to conversation

usb: gadget: goku_udc: fix potential crashes in probe

PATCH In review Sasha Levin 2 participants 23 messages Nov 10, 2020 – Nov 14, 2020

Subsystems (10)
lore
Share & tools
lore

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/21 usb: gadget: goku_udc: fix potential crashes in probe

From: Evgeny Novikov <[email protected]>

[ Upstream commit 0d66e04875c5aae876cf3d4f4be7978fa2b00523 ]

goku_probe() goes to error label "err" and invokes goku_remove() in case of failures of pci_enable_device(), pci_resource_start() and ioremap(). goku_remove() gets a device from pci_get_drvdata(pdev) and works with it without any checks, in particular it dereferences a corresponding pointer. But goku_probe() did not set this device yet. So, one can expect various crashes. The patch moves setting the device just after allocation of memory for it.

Found by Linux Driver Verification project (linuxtesting.org).

---
 drivers/usb/gadget/udc/goku_udc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/gadget/udc/goku_udc.c +1 -1
index c3721225b61ed..b706ad3034bc1 100644
@@ -1757,6 +1757,7 @@ static int goku_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		goto err;
 	}
 
+	pci_set_drvdata(pdev, dev);
 	spin_lock_init(&dev->lock);
 	dev->pdev = pdev;
 	dev->gadget.ops = &goku_ops;
@@ -1790,7 +1791,6 @@ static int goku_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	}
 	dev->regs = (struct goku_udc_regs __iomem *) base;
 
-	pci_set_drvdata(pdev, dev);
 	INFO(dev, "%s\n", driver_desc);
 	INFO(dev, "version: " DRIVER_VERSION " %s\n", dmastr());
 	INFO(dev, "irq %d, pci mem %p\n", pdev->irq, base);
Signature · 1 line
2.27.0
author maintainer
#1 lore raw

PATCH 2/21 ALSA: hda: Reinstate runtime_allow() for all hda controllers

From: Kai-Heng Feng <[email protected]>

[ Upstream commit 9fc149c3bce7bdbb94948a8e6bd025e3b3538603 ]

The broken jack detection should be fixed by commit a6e7d0a4bdb0 ("ALSA:
hda: fix jack detection with Realtek codecs when in D3"), let's try enabling runtime PM by default again.

---
 sound/pci/hda/hda_intel.c | 1 +
 1 file changed, 1 insertion(+)
sound/pci/hda/hda_intel.c +1 -0
index d43245937db7e..8e1eb5f243a27 100644
@@ -2478,6 +2478,7 @@ static int azx_probe_continue(struct azx *chip)
 
 	if (azx_has_pm_runtime(chip)) {
 		pm_runtime_use_autosuspend(&pci->dev);
+		pm_runtime_allow(&pci->dev);
 		pm_runtime_put_autosuspend(&pci->dev);
 	}
 
Signature · 1 line
2.27.0
author maintainer
#2 lore raw

PATCH 3/21 gfs2: Free rd_bits later in gfs2_clear_rgrpd to fix use-after-free

In reply to Sasha Levin

From: Bob Peterson <[email protected]>

[ Upstream commit d0f17d3883f1e3f085d38572c2ea8edbd5150172 ]

Function gfs2_clear_rgrpd calls kfree(rgd->rd_bits) before calling return_all_reservations, but return_all_reservations still dereferences rgd->rd_bits in __rs_deltree. Fix that by moving the call to kfree below the call to return_all_reservations.

---
 fs/gfs2/rgrp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/gfs2/rgrp.c +1 -1
index c94c4ac1ae78b..1686a40099f21 100644
@@ -739,9 +739,9 @@ void gfs2_clear_rgrpd(struct gfs2_sbd *sdp)
 		}
 
 		gfs2_free_clones(rgd);
+		return_all_reservations(rgd);
 		kfree(rgd->rd_bits);
 		rgd->rd_bits = NULL;
-		return_all_reservations(rgd);
 		kmem_cache_free(gfs2_rgrpd_cachep, rgd);
 	}
 }
Signature · 1 line
2.27.0
author maintainer
#3 lore raw

PATCH 4/21 gfs2: Add missing truncate_inode_pages_final for sd_aspace

In reply to Sasha Levin

From: Bob Peterson <[email protected]>

[ Upstream commit a9dd945ccef07a904e412f208f8de708a3d7159e ]

Gfs2 creates an address space for its rgrps called sd_aspace, but it never called truncate_inode_pages_final on it. This confused vfs greatly which tried to reference the address space after gfs2 had freed the superblock that contained it.

This patch adds a call to truncate_inode_pages_final for sd_aspace, thus avoiding the use-after-free.

---
 fs/gfs2/super.c | 1 +
 1 file changed, 1 insertion(+)
fs/gfs2/super.c +1 -0
index a971862b186e3..22cd68bd8c9b0 100644
@@ -934,6 +934,7 @@ static void gfs2_put_super(struct super_block *sb)
 	gfs2_jindex_free(sdp);
 	/*  Take apart glock structures and buffer lists  */
 	gfs2_gl_hash_clear(sdp);
+	truncate_inode_pages_final(&sdp->sd_aspace);
 	gfs2_delete_debugfs_file(sdp);
 	/*  Unmount the locking protocol  */
 	gfs2_lm_unmount(sdp);
Signature · 1 line
2.27.0
author maintainer
#4 lore raw

PATCH 5/21 gfs2: check for live vs. read-only file system in gfs2_fitrim

In reply to Sasha Levin

From: Bob Peterson <[email protected]>

[ Upstream commit c5c68724696e7d2f8db58a5fce3673208d35c485 ]

Before this patch, gfs2_fitrim was not properly checking for a "live" file system. If the file system had something to trim and the file system was read-only (or spectator) it would start the trim, but when it starts the transaction, gfs2_trans_begin returns -EROFS (read-only file system) and it errors out. However, if the file system was already trimmed so there's no work to do, it never called gfs2_trans_begin. That code is bypassed so it never returns the error. Instead, it returns a good return code with 0 work. All this makes for inconsistent behavior:
The same fstrim command can return -EROFS in one case and 0 in another. This tripped up xfstests generic/537 which reports the error as:

+fstrim with unrecovered metadata just ate your filesystem

This patch adds a check for a "live" (iow, active journal, iow, RW) file system, and if not, returns the error properly.

---
 fs/gfs2/rgrp.c | 3 +++
 1 file changed, 3 insertions(+)
fs/gfs2/rgrp.c +3 -0
index 1686a40099f21..de9b561b1c385 100644
@@ -1387,6 +1387,9 @@ int gfs2_fitrim(struct file *filp, void __user *argp)
 	if (!capable(CAP_SYS_ADMIN))
 		return -EPERM;
 
+	if (!test_bit(SDF_JOURNAL_LIVE, &sdp->sd_flags))
+		return -EROFS;
+
 	if (!blk_queue_discard(q))
 		return -EOPNOTSUPP;
 
Signature · 1 line
2.27.0
author maintainer
#5 lore raw

PATCH 6/21 scsi: hpsa: Fix memory leak in hpsa_init_one()

In reply to Sasha Levin

From: Keita Suzuki <[email protected]>

[ Upstream commit af61bc1e33d2c0ec22612b46050f5b58ac56a962 ]

When hpsa_scsi_add_host() fails, h->lastlogicals is leaked since it is missing a free() in the error handler.

Fix this by adding free() when hpsa_scsi_add_host() fails.

---
 drivers/scsi/hpsa.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/scsi/hpsa.c +3 -1
index 11de2198bb87d..0fe21cbdf0ca7 100644
@@ -8781,7 +8781,7 @@ static int hpsa_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	/* hook into SCSI subsystem */
 	rc = hpsa_scsi_add_host(h);
 	if (rc)
-		goto clean7; /* perf, sg, cmd, irq, shost, pci, lu, aer/h */
+		goto clean8; /* lastlogicals, perf, sg, cmd, irq, shost, pci, lu, aer/h */
 
 	/* Monitor the controller for firmware lockups */
 	h->heartbeat_sample_interval = HEARTBEAT_SAMPLE_INTERVAL;
@@ -8796,6 +8796,8 @@ static int hpsa_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 				HPSA_EVENT_MONITOR_INTERVAL);
 	return 0;
 
+clean8: /* lastlogicals, perf, sg, cmd, irq, shost, pci, lu, aer/h */
+	kfree(h->lastlogicals);
 clean7: /* perf, sg, cmd, irq, shost, pci, lu, aer/h */
 	hpsa_free_performant_mode(h);
 	h->access.set_intr_mask(h, HPSA_INTR_OFF);
Signature · 1 line
2.27.0
author maintainer
#6 lore raw

PATCH 7/21 drm/amdgpu: perform srbm soft reset always on SDMA resume

In reply to Sasha Levin

From: Evan Quan <[email protected]>

[ Upstream commit 253475c455eb5f8da34faa1af92709e7bb414624 ]

This can address the random SDMA hang after pci config reset seen on Hawaii.

---
 drivers/gpu/drm/amd/amdgpu/cik_sdma.c | 27 ++++++++++++---------------
 1 file changed, 12 insertions(+), 15 deletions(-)
drivers/gpu/drm/amd/amdgpu/cik_sdma.c +12 -15
index d0fa2aac23888..ca66c2f797584 100644
@@ -1086,22 +1086,19 @@ static int cik_sdma_soft_reset(void *handle)
 {
 	u32 srbm_soft_reset = 0;
 	struct amdgpu_device *adev = (struct amdgpu_device *)handle;
-	u32 tmp = RREG32(mmSRBM_STATUS2);
+	u32 tmp;
 
-	if (tmp & SRBM_STATUS2__SDMA_BUSY_MASK) {
-		/* sdma0 */
-		tmp = RREG32(mmSDMA0_F32_CNTL + SDMA0_REGISTER_OFFSET);
-		tmp |= SDMA0_F32_CNTL__HALT_MASK;
-		WREG32(mmSDMA0_F32_CNTL + SDMA0_REGISTER_OFFSET, tmp);
-		srbm_soft_reset |= SRBM_SOFT_RESET__SOFT_RESET_SDMA_MASK;
-	}
-	if (tmp & SRBM_STATUS2__SDMA1_BUSY_MASK) {
-		/* sdma1 */
-		tmp = RREG32(mmSDMA0_F32_CNTL + SDMA1_REGISTER_OFFSET);
-		tmp |= SDMA0_F32_CNTL__HALT_MASK;
-		WREG32(mmSDMA0_F32_CNTL + SDMA1_REGISTER_OFFSET, tmp);
-		srbm_soft_reset |= SRBM_SOFT_RESET__SOFT_RESET_SDMA1_MASK;
-	}
+	/* sdma0 */
+	tmp = RREG32(mmSDMA0_F32_CNTL + SDMA0_REGISTER_OFFSET);
+	tmp |= SDMA0_F32_CNTL__HALT_MASK;
+	WREG32(mmSDMA0_F32_CNTL + SDMA0_REGISTER_OFFSET, tmp);
+	srbm_soft_reset |= SRBM_SOFT_RESET__SOFT_RESET_SDMA_MASK;
+
+	/* sdma1 */
+	tmp = RREG32(mmSDMA0_F32_CNTL + SDMA1_REGISTER_OFFSET);
+	tmp |= SDMA0_F32_CNTL__HALT_MASK;
+	WREG32(mmSDMA0_F32_CNTL + SDMA1_REGISTER_OFFSET, tmp);
+	srbm_soft_reset |= SRBM_SOFT_RESET__SOFT_RESET_SDMA1_MASK;
 
 	if (srbm_soft_reset) {
 		tmp = RREG32(mmSRBM_SOFT_RESET);
Signature · 6 lines
2.27.0

_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
author maintainer
#7 lore raw

PATCH 8/21 drm/amd/pm: perform SMC reset on suspend/hibernation

In reply to Sasha Levin

From: Evan Quan <[email protected]>

[ Upstream commit 277b080f98803cb73a83fb234f0be83a10e63958 ]

So that the succeeding resume can be performed based on a clean state.

---
 .../gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c  |  4 ++++
 drivers/gpu/drm/amd/powerplay/inc/hwmgr.h     |  1 +
 drivers/gpu/drm/amd/powerplay/inc/smumgr.h    |  2 ++
 .../gpu/drm/amd/powerplay/smumgr/ci_smumgr.c  | 24 +++++++++++++++++++
 drivers/gpu/drm/amd/powerplay/smumgr/smumgr.c |  8 +++++++
 5 files changed, 39 insertions(+)
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c +4 -0
index 058898b321b8a..d8e624d64ae38 100644
@@ -1531,6 +1531,10 @@ int smu7_disable_dpm_tasks(struct pp_hwmgr *hwmgr)
 	PP_ASSERT_WITH_CODE((tmp_result == 0),
 			"Failed to reset to default!", result = tmp_result);
 
+	tmp_result = smum_stop_smc(hwmgr);
+	PP_ASSERT_WITH_CODE((tmp_result == 0),
+			"Failed to stop smc!", result = tmp_result);
+
 	tmp_result = smu7_force_switch_to_arbf0(hwmgr);
 	PP_ASSERT_WITH_CODE((tmp_result == 0),
 			"Failed to force to switch arbf0!", result = tmp_result);
drivers/gpu/drm/amd/powerplay/inc/hwmgr.h +1 -0
index 6ee864455a12a..f59e1e737735f 100644
@@ -216,6 +216,7 @@ struct pp_smumgr_func {
 	bool (*is_hw_avfs_present)(struct pp_hwmgr  *hwmgr);
 	int (*update_dpm_settings)(struct pp_hwmgr *hwmgr, void *profile_setting);
 	int (*smc_table_manager)(struct pp_hwmgr *hwmgr, uint8_t *table, uint16_t table_id, bool rw); /*rw: true for read, false for write */
+	int (*stop_smc)(struct pp_hwmgr *hwmgr);
 };
 
 struct pp_hwmgr_func {
drivers/gpu/drm/amd/powerplay/inc/smumgr.h +2 -0
index 82550a8a3a3fc..ef4f2392e2e7d 100644
@@ -113,4 +113,6 @@ extern int smum_update_dpm_settings(struct pp_hwmgr *hwmgr, void *profile_settin
 
 extern int smum_smc_table_manager(struct pp_hwmgr *hwmgr, uint8_t *table, uint16_t table_id, bool rw);
 
+extern int smum_stop_smc(struct pp_hwmgr *hwmgr);
+
 #endif
drivers/gpu/drm/amd/powerplay/smumgr/ci_smumgr.c +24 -0
index db87cb8930d24..0d4dd607e85c8 100644
@@ -2934,6 +2934,29 @@ static int ci_update_smc_table(struct pp_hwmgr *hwmgr, uint32_t type)
 	return 0;
 }
 
+static void ci_reset_smc(struct pp_hwmgr *hwmgr)
+{
+	PHM_WRITE_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
+				  SMC_SYSCON_RESET_CNTL,
+				  rst_reg, 1);
+}
+
+
+static void ci_stop_smc_clock(struct pp_hwmgr *hwmgr)
+{
+	PHM_WRITE_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC,
+				  SMC_SYSCON_CLOCK_CNTL_0,
+				  ck_disable, 1);
+}
+
+static int ci_stop_smc(struct pp_hwmgr *hwmgr)
+{
+	ci_reset_smc(hwmgr);
+	ci_stop_smc_clock(hwmgr);
+
+	return 0;
+}
+
 const struct pp_smumgr_func ci_smu_funcs = {
 	.smu_init = ci_smu_init,
 	.smu_fini = ci_smu_fini,
@@ -2957,4 +2980,5 @@ const struct pp_smumgr_func ci_smu_funcs = {
 	.is_dpm_running = ci_is_dpm_running,
 	.update_dpm_settings = ci_update_dpm_settings,
 	.update_smc_table = ci_update_smc_table,
+	.stop_smc = ci_stop_smc,
 };
drivers/gpu/drm/amd/powerplay/smumgr/smumgr.c +8 -0
index a6edd5df33b0f..20ecf994d47f3 100644
@@ -213,3 +213,11 @@ int smum_smc_table_manager(struct pp_hwmgr *hwmgr, uint8_t *table, uint16_t tabl
 
 	return -EINVAL;
 }
+
+int smum_stop_smc(struct pp_hwmgr *hwmgr)
+{
+	if (hwmgr->smumgr_funcs->stop_smc)
+		return hwmgr->smumgr_funcs->stop_smc(hwmgr);
+
+	return 0;
+}
Signature · 6 lines
2.27.0

_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
author maintainer
#8 lore raw

PATCH 9/21 drm/amd/pm: do not use ixFEATURE_STATUS for checking smc running

In reply to Sasha Levin

From: Evan Quan <[email protected]>

[ Upstream commit 786436b453001dafe81025389f96bf9dac1e9690 ]

This reverts commit f87812284172a9809820d10143b573d833cd3f75 ("drm/amdgpu:
Fix bug where DPM is not enabled after hibernate and resume"). It was intended to fix Hawaii S4(hibernation) issue but break S3. As ixFEATURE_STATUS is filled with garbage data on resume which can be only cleared by reloading smc firmware(but that will involve many changes). So, we will revert this S4 fix and seek a new way.

---
 drivers/gpu/drm/amd/powerplay/smumgr/ci_smumgr.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/gpu/drm/amd/powerplay/smumgr/ci_smumgr.c +1 -4
index 0d4dd607e85c8..c05bec5effb2e 100644
@@ -2723,10 +2723,7 @@ static int ci_initialize_mc_reg_table(struct pp_hwmgr *hwmgr)
 
 static bool ci_is_dpm_running(struct pp_hwmgr *hwmgr)
 {
-	return (1 == PHM_READ_INDIRECT_FIELD(hwmgr->device,
-					     CGS_IND_REG__SMC, FEATURE_STATUS,
-					     VOLTAGE_CONTROLLER_ON))
-		? true : false;
+	return ci_is_smc_ram_running(hwmgr);
 }
 
 static int ci_smu_init(struct pp_hwmgr *hwmgr)
Signature · 6 lines
2.27.0

_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
author maintainer
#9 lore raw

PATCH 10/21 mac80211: fix use of skb payload instead of header

In reply to Sasha Levin

From: Johannes Berg <[email protected]>

[ Upstream commit 14f46c1e5108696ec1e5a129e838ecedf108c7bf ]

When ieee80211_skb_resize() is called from ieee80211_build_hdr() the skb has no 802.11 header yet, in fact it consist only of the payload as the ethernet frame is removed. As such, we're using the payload data for ieee80211_is_mgmt(), which is of course completely wrong. This didn't really hurt us because these are always data frames, so we could only have added more tailroom than we needed if we determined it was a management frame and sdata->crypto_tx_tailroom_needed_cnt was false.

However, syzbot found that of course there need not be any payload, so we're using at best uninitialized memory for the check.

Fix this to pass explicitly the kind of frame that we have instead of checking there, by replacing the "bool may_encrypt" argument with an argument that can carry the three possible states - it's not going to be encrypted, it's a management frame, or it's a data frame (and then we check sdata->crypto_tx_tailroom_needed_cnt).

---
 net/mac80211/tx.c | 37 ++++++++++++++++++++++++-------------
 1 file changed, 24 insertions(+), 13 deletions(-)
net/mac80211/tx.c +24 -13
index 3160ffd93a153..98d048630ad2f 100644
@@ -1908,19 +1908,24 @@ static bool ieee80211_tx(struct ieee80211_sub_if_data *sdata,
 
 /* device xmit handlers */
 
+enum ieee80211_encrypt {
+	ENCRYPT_NO,
+	ENCRYPT_MGMT,
+	ENCRYPT_DATA,
+};
+
 static int ieee80211_skb_resize(struct ieee80211_sub_if_data *sdata,
 				struct sk_buff *skb,
-				int head_need, bool may_encrypt)
+				int head_need,
+				enum ieee80211_encrypt encrypt)
 {
 	struct ieee80211_local *local = sdata->local;
-	struct ieee80211_hdr *hdr;
 	bool enc_tailroom;
 	int tail_need = 0;
 
-	hdr = (struct ieee80211_hdr *) skb->data;
-	enc_tailroom = may_encrypt &&
-		       (sdata->crypto_tx_tailroom_needed_cnt ||
-			ieee80211_is_mgmt(hdr->frame_control));
+	enc_tailroom = encrypt == ENCRYPT_MGMT ||
+		       (encrypt == ENCRYPT_DATA &&
+			sdata->crypto_tx_tailroom_needed_cnt);
 
 	if (enc_tailroom) {
 		tail_need = IEEE80211_ENCRYPT_TAILROOM;
@@ -1952,23 +1957,29 @@ void ieee80211_xmit(struct ieee80211_sub_if_data *sdata,
 {
 	struct ieee80211_local *local = sdata->local;
 	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
-	struct ieee80211_hdr *hdr;
+	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
 	int headroom;
-	bool may_encrypt;
+	enum ieee80211_encrypt encrypt;
 
-	may_encrypt = !(info->flags & IEEE80211_TX_INTFL_DONT_ENCRYPT);
+	if (info->flags & IEEE80211_TX_INTFL_DONT_ENCRYPT)
+		encrypt = ENCRYPT_NO;
+	else if (ieee80211_is_mgmt(hdr->frame_control))
+		encrypt = ENCRYPT_MGMT;
+	else
+		encrypt = ENCRYPT_DATA;
 
 	headroom = local->tx_headroom;
-	if (may_encrypt)
+	if (encrypt != ENCRYPT_NO)
 		headroom += sdata->encrypt_headroom;
 	headroom -= skb_headroom(skb);
 	headroom = max_t(int, 0, headroom);
 
-	if (ieee80211_skb_resize(sdata, skb, headroom, may_encrypt)) {
+	if (ieee80211_skb_resize(sdata, skb, headroom, encrypt)) {
 		ieee80211_free_txskb(&local->hw, skb);
 		return;
 	}
 
+	/* reload after potential resize */
 	hdr = (struct ieee80211_hdr *) skb->data;
 	info->control.vif = &sdata->vif;
 
@@ -2751,7 +2762,7 @@ static struct sk_buff *ieee80211_build_hdr(struct ieee80211_sub_if_data *sdata,
 		head_need += sdata->encrypt_headroom;
 		head_need += local->tx_headroom;
 		head_need = max_t(int, 0, head_need);
-		if (ieee80211_skb_resize(sdata, skb, head_need, true)) {
+		if (ieee80211_skb_resize(sdata, skb, head_need, ENCRYPT_DATA)) {
 			ieee80211_free_txskb(&local->hw, skb);
 			skb = NULL;
 			return ERR_PTR(-ENOMEM);
@@ -3414,7 +3425,7 @@ static bool ieee80211_xmit_fast(struct ieee80211_sub_if_data *sdata,
 	if (unlikely(ieee80211_skb_resize(sdata, skb,
 					  max_t(int, extra_head + hw_headroom -
 						     skb_headroom(skb), 0),
-					  false))) {
+					  ENCRYPT_NO))) {
 		kfree_skb(skb);
 		return true;
 	}
Signature · 1 line
2.27.0
author maintainer
#10 lore raw

PATCH 11/21 mac80211: always wind down STA state

In reply to Sasha Levin

From: Johannes Berg <[email protected]>

[ Upstream commit dcd479e10a0510522a5d88b29b8f79ea3467d501 ]

When (for example) an IBSS station is pre-moved to AUTHORIZED before it's inserted, and then the insertion fails, we don't clean up the fast RX/TX states that might already have been created, since we don't go through all the state transitions again on the way down.

Do that, if it hasn't been done already, when the station is freed. I considered only freeing the fast TX/RX state there, but we might add more state so it's more robust to wind down the state properly.

Note that we warn if the station was ever inserted, it should have been properly cleaned up in that case, and the driver will probably not like things happening out of order.

---
 net/mac80211/sta_info.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
net/mac80211/sta_info.c +18 -0
index 9968b8a976f19..d11eb5139c92a 100644
@@ -244,6 +244,24 @@ struct sta_info *sta_info_get_by_idx(struct ieee80211_sub_if_data *sdata,
  */
 void sta_info_free(struct ieee80211_local *local, struct sta_info *sta)
 {
+	/*
+	 * If we had used sta_info_pre_move_state() then we might not
+	 * have gone through the state transitions down again, so do
+	 * it here now (and warn if it's inserted).
+	 *
+	 * This will clear state such as fast TX/RX that may have been
+	 * allocated during state transitions.
+	 */
+	while (sta->sta_state > IEEE80211_STA_NONE) {
+		int ret;
+
+		WARN_ON_ONCE(test_sta_flag(sta, WLAN_STA_INSERTED));
+
+		ret = sta_info_move_state(sta, sta->sta_state - 1);
+		if (WARN_ONCE(ret, "sta_info_move_state() returned %d\n", ret))
+			break;
+	}
+
 	if (sta->rate_ctrl)
 		rate_control_free_sta(sta);
 
Signature · 1 line
2.27.0
author maintainer
#11 lore raw

PATCH 12/21 cfg80211: regulatory: Fix inconsistent format argument

In reply to Sasha Levin

From: Ye Bin <[email protected]>

[ Upstream commit db18d20d1cb0fde16d518fb5ccd38679f174bc04 ]

Fix follow warning:
[net/wireless/reg.c:3619]: (warning) %d in format string (no. 2) requires 'int' but the argument type is 'unsigned int'.

---
 net/wireless/reg.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/wireless/reg.c +1 -1
index 935aebf150107..c7825b951f725 100644
@@ -3374,7 +3374,7 @@ static void print_rd_rules(const struct ieee80211_regdomain *rd)
 		power_rule = &reg_rule->power_rule;
 
 		if (reg_rule->flags & NL80211_RRF_AUTO_BW)
-			snprintf(bw, sizeof(bw), "%d KHz, %d KHz AUTO",
+			snprintf(bw, sizeof(bw), "%d KHz, %u KHz AUTO",
 				 freq_range->max_bandwidth_khz,
 				 reg_get_max_bandwidth(rd, reg_rule));
 		else
Signature · 1 line
2.27.0
author maintainer
#12 lore raw

PATCH 13/21 scsi: scsi_dh_alua: Avoid crash during alua_bus_detach()

In reply to Sasha Levin

From: Hannes Reinecke <[email protected]>

[ Upstream commit 5faf50e9e9fdc2117c61ff7e20da49cd6a29e0ca ]

alua_bus_detach() might be running concurrently with alua_rtpg_work(), so we might trip over h->sdev == NULL and call BUG_ON(). The correct way of handling it is to not set h->sdev to NULL in alua_bus_detach(), and call rcu_synchronize() before the final delete to ensure that all concurrent threads have left the critical section. Then we can get rid of the BUG_ON() and replace it with a simple if condition.

---
 drivers/scsi/device_handler/scsi_dh_alua.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/scsi/device_handler/scsi_dh_alua.c +5 -4
index c95c782b93a53..60c48dc5d9453 100644
@@ -672,8 +672,8 @@ static int alua_rtpg(struct scsi_device *sdev, struct alua_port_group *pg)
 					rcu_read_lock();
 					list_for_each_entry_rcu(h,
 						&tmp_pg->dh_list, node) {
-						/* h->sdev should always be valid */
-						BUG_ON(!h->sdev);
+						if (!h->sdev)
+							continue;
 						h->sdev->access_state = desc[0];
 					}
 					rcu_read_unlock();
@@ -719,7 +719,8 @@ static int alua_rtpg(struct scsi_device *sdev, struct alua_port_group *pg)
 			pg->expiry = 0;
 			rcu_read_lock();
 			list_for_each_entry_rcu(h, &pg->dh_list, node) {
-				BUG_ON(!h->sdev);
+				if (!h->sdev)
+					continue;
 				h->sdev->access_state =
 					(pg->state & SCSI_ACCESS_STATE_MASK);
 				if (pg->pref)
@@ -1160,7 +1161,6 @@ static void alua_bus_detach(struct scsi_device *sdev)
 	spin_lock(&h->pg_lock);
 	pg = rcu_dereference_protected(h->pg, lockdep_is_held(&h->pg_lock));
 	rcu_assign_pointer(h->pg, NULL);
-	h->sdev = NULL;
 	spin_unlock(&h->pg_lock);
 	if (pg) {
 		spin_lock_irq(&pg->lock);
@@ -1169,6 +1169,7 @@ static void alua_bus_detach(struct scsi_device *sdev)
 		kref_put(&pg->kref, release_port_group);
 	}
 	sdev->handler_data = NULL;
+	synchronize_rcu();
 	kfree(h);
 }
 
Signature · 1 line
2.27.0
author maintainer
#13 lore raw

PATCH 14/21 iommu/amd: Increase interrupt remapping table limit to 512 entries

In reply to Sasha Levin

From: Suravee Suthikulpanit <[email protected]>

[ Upstream commit 73db2fc595f358460ce32bcaa3be1f0cce4a2db1 ]

Certain device drivers allocate IO queues on a per-cpu basis. On AMD EPYC platform, which can support up-to 256 cpu threads, this can exceed the current MAX_IRQ_PER_TABLE limit of 256, and result in the error message:

AMD-Vi: Failed to allocate IRTE

This has been observed with certain NVME devices.

AMD IOMMU hardware can actually support upto 512 interrupt remapping table entries. Therefore, update the driver to match the hardware limit.

Please note that this also increases the size of interrupt remapping table to 8KB per device when using the 128-bit IRTE format.

---
 drivers/iommu/amd_iommu_types.h | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/iommu/amd_iommu_types.h +5 -1
index 859b06424e5c4..df6f3cc958e5e 100644
@@ -410,7 +410,11 @@ extern bool amd_iommu_np_cache;
 /* Only true if all IOMMUs support device IOTLBs */
 extern bool amd_iommu_iotlb_sup;
 
-#define MAX_IRQS_PER_TABLE	256
+/*
+ * AMD IOMMU hardware only support 512 IRTEs despite
+ * the architectural limitation of 2048 entries.
+ */
+#define MAX_IRQS_PER_TABLE	512
 #define IRQ_TABLE_ALIGNMENT	128
 
 struct irq_remap_table {
Signature · 6 lines
2.27.0

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#14 lore raw

PATCH 15/21 s390/smp: move rcu_cpu_starting() earlier

In reply to Sasha Levin

From: Qian Cai <[email protected]>

[ Upstream commit de5d9dae150ca1c1b5c7676711a9ca139d1a8dec ]

The call to rcu_cpu_starting() in smp_init_secondary() is not early enough in the CPU-hotplug onlining process, which results in lockdep splats as follows:

WARNING: suspicious RCU usage
-----------------------------
kernel/locking/lockdep.c:3497 RCU-list traversed in non-reader section!!

other info that might help us debug this:

RCU used illegally from offline CPU!
rcu_scheduler_active = 1, debug_locks = 1
no locks held by swapper/1/0.

 Call Trace:
 show_stack+0x158/0x1f0
 dump_stack+0x1f2/0x238
 __lock_acquire+0x2640/0x4dd0
 lock_acquire+0x3a8/0xd08
 _raw_spin_lock_irqsave+0xc0/0xf0
 clockevents_register_device+0xa8/0x528
 init_cpu_timer+0x33e/0x468
 smp_init_secondary+0x11a/0x328
 smp_start_secondary+0x82/0x88

This is avoided by moving the call to rcu_cpu_starting up near the beginning of the smp_init_secondary() function. Note that the raw_smp_processor_id() is required in order to avoid calling into lockdep before RCU has declared the CPU to be watched for readers.

---
 arch/s390/kernel/smp.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
arch/s390/kernel/smp.c +2 -1
index 8e31dfd85de32..888f247c9261a 100644
@@ -831,7 +831,7 @@ void __init smp_detect_cpus(void)
  */
 static void smp_start_secondary(void *cpuvoid)
 {
-	int cpu = smp_processor_id();
+	int cpu = raw_smp_processor_id();
 
 	S390_lowcore.last_update_clock = get_tod_clock();
 	S390_lowcore.restart_stack = (unsigned long) restart_stack;
@@ -844,6 +844,7 @@ static void smp_start_secondary(void *cpuvoid)
 	set_cpu_flag(CIF_ASCE_PRIMARY);
 	set_cpu_flag(CIF_ASCE_SECONDARY);
 	cpu_init();
+	rcu_cpu_starting(cpu);
 	preempt_disable();
 	init_cpu_timer();
 	vtime_init();
Signature · 1 line
2.27.0
author maintainer
#15 lore raw

PATCH 16/21 vfio: platform: fix reference leak in vfio_platform_open

In reply to Sasha Levin

From: Zhang Qilong <[email protected]>

[ Upstream commit bb742ad01961a3b9d1f9d19375487b879668b6b2 ]

pm_runtime_get_sync() will increment pm usage counter even it failed. Forgetting to call pm_runtime_put will result in reference leak in vfio_platform_open, so we should fix it.

---
 drivers/vfio/platform/vfio_platform_common.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/vfio/platform/vfio_platform_common.c +1 -2
index c0cd824be2b76..460760d0becfe 100644
@@ -273,7 +273,7 @@ static int vfio_platform_open(void *device_data)
 
 		ret = pm_runtime_get_sync(vdev->device);
 		if (ret < 0)
-			goto err_pm;
+			goto err_rst;
 
 		ret = vfio_platform_call_reset(vdev, &extra_dbg);
 		if (ret && vdev->reset_required) {
@@ -290,7 +290,6 @@ static int vfio_platform_open(void *device_data)
 
 err_rst:
 	pm_runtime_put(vdev->device);
-err_pm:
 	vfio_platform_irq_cleanup(vdev);
 err_irq:
 	vfio_platform_regions_cleanup(vdev);
Signature · 1 line
2.27.0
author maintainer
#16 lore raw

PATCH 17/21 net: usb: qmi_wwan: add Telit LE910Cx 0x1230 composition

In reply to Sasha Levin

From: Daniele Palmas <[email protected]>

[ Upstream commit 5fd8477ed8ca77e64b93d44a6dae4aa70c191396 ]

Add support for Telit LE910Cx 0x1230 composition:

0x1230: tty, adb, rmnet, audio, tty, tty, tty, tty

---
 drivers/net/usb/qmi_wwan.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/usb/qmi_wwan.c +1 -0
index d2612b69257ea..6e0b3dc14aa47 100644
@@ -1268,6 +1268,7 @@ static const struct usb_device_id products[] = {
 	{QMI_FIXED_INTF(0x1bc7, 0x1101, 3)},	/* Telit ME910 dual modem */
 	{QMI_FIXED_INTF(0x1bc7, 0x1200, 5)},	/* Telit LE920 */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1201, 2)},	/* Telit LE920, LE920A4 */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1230, 2)},	/* Telit LE910Cx */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1260, 2)},	/* Telit LE910Cx */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1261, 2)},	/* Telit LE910Cx */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1900, 1)},	/* Telit LN940 series */
Signature · 1 line
2.27.0
author maintainer
#17 lore raw

PATCH 18/21 kprobes: Tell lockdep about kprobe nesting

In reply to Sasha Levin

From: "Steven Rostedt (VMware)" <[email protected]>

[ Upstream commit 645f224e7ba2f4200bf163153d384ceb0de5462e ]

Since the kprobe handlers have protection that prohibits other handlers from executing in other contexts (like if an NMI comes in while processing a kprobe, and executes the same kprobe, it will get fail with a "busy" return). Lockdep is unaware of this protection. Use lockdep's nesting api to differentiate between locks taken in INT3 context and other context to suppress the false warnings.

---
 kernel/kprobes.c | 25 +++++++++++++++++++++----
 1 file changed, 21 insertions(+), 4 deletions(-)
kernel/kprobes.c +21 -4
index 2161f519d4812..2ce9053de6ae4 100644
@@ -1204,7 +1204,13 @@ __acquires(hlist_lock)
 
 	*head = &kretprobe_inst_table[hash];
 	hlist_lock = kretprobe_table_lock_ptr(hash);
-	raw_spin_lock_irqsave(hlist_lock, *flags);
+	/*
+	 * Nested is a workaround that will soon not be needed.
+	 * There's other protections that make sure the same lock
+	 * is not taken on the same CPU that lockdep is unaware of.
+	 * Differentiate when it is taken in NMI context.
+	 */
+	raw_spin_lock_irqsave_nested(hlist_lock, *flags, !!in_nmi());
 }
 NOKPROBE_SYMBOL(kretprobe_hash_lock);
 
@@ -1213,7 +1219,13 @@ static void kretprobe_table_lock(unsigned long hash,
 __acquires(hlist_lock)
 {
 	raw_spinlock_t *hlist_lock = kretprobe_table_lock_ptr(hash);
-	raw_spin_lock_irqsave(hlist_lock, *flags);
+	/*
+	 * Nested is a workaround that will soon not be needed.
+	 * There's other protections that make sure the same lock
+	 * is not taken on the same CPU that lockdep is unaware of.
+	 * Differentiate when it is taken in NMI context.
+	 */
+	raw_spin_lock_irqsave_nested(hlist_lock, *flags, !!in_nmi());
 }
 NOKPROBE_SYMBOL(kretprobe_table_lock);
 
@@ -1884,7 +1896,12 @@ static int pre_handler_kretprobe(struct kprobe *p, struct pt_regs *regs)
 
 	/* TODO: consider to only swap the RA after the last pre_handler fired */
 	hash = hash_ptr(current, KPROBE_HASH_BITS);
-	raw_spin_lock_irqsave(&rp->lock, flags);
+	/*
+	 * Nested is a workaround that will soon not be needed.
+	 * There's other protections that make sure the same lock
+	 * is not taken on the same CPU that lockdep is unaware of.
+	 */
+	raw_spin_lock_irqsave_nested(&rp->lock, flags, 1);
 	if (!hlist_empty(&rp->free_instances)) {
 		ri = hlist_entry(rp->free_instances.first,
 				struct kretprobe_instance, hlist);
@@ -1895,7 +1912,7 @@ static int pre_handler_kretprobe(struct kprobe *p, struct pt_regs *regs)
 		ri->task = current;
 
 		if (rp->entry_handler && rp->entry_handler(ri, regs)) {
-			raw_spin_lock_irqsave(&rp->lock, flags);
+			raw_spin_lock_irqsave_nested(&rp->lock, flags, 1);
 			hlist_add_head(&ri->hlist, &rp->free_instances);
 			raw_spin_unlock_irqrestore(&rp->lock, flags);
 			return 0;
Signature · 1 line
2.27.0
#18 lore raw

Re: [PATCH AUTOSEL 4.19 18/21] kprobes: Tell lockdep about kprobe nesting

Hi,

Quoted 4 lines · On Mon, 9 Nov 2020 22:55:38 -0500 Sasha Levin <[email protected]> wrote:

From: "Steven Rostedt (VMware)" <[email protected]>

[ Upstream commit 645f224e7ba2f4200bf163153d384ceb0de5462e ]

Quoted 9 lines

Since the kprobe handlers have protection that prohibits other handlers from executing in other contexts (like if an NMI comes in while processing a kprobe, and executes the same kprobe, it will get fail with a "busy" return). Lockdep is unaware of this protection. Use lockdep's nesting api to differentiate between locks taken in INT3 context and other context to suppress the false warnings.

This fixes a lockdep false positive warning comes from commit e03b4a084ea6 ("kprobes: Remove NMI context check"). Does anyone report that happen on the stable kernel?

If not, you do not need this patch for stable kernels.

Thank you,

Quoted 68 lines
---
 kernel/kprobes.c | 25 +++++++++++++++++++++----
 1 file changed, 21 insertions(+), 4 deletions(-)
kernel/kprobes.c +21 -4
index 2161f519d4812..2ce9053de6ae4 100644
@@ -1204,7 +1204,13 @@ __acquires(hlist_lock)
 
 	*head = &kretprobe_inst_table[hash];
 	hlist_lock = kretprobe_table_lock_ptr(hash);
-	raw_spin_lock_irqsave(hlist_lock, *flags);
+	/*
+	 * Nested is a workaround that will soon not be needed.
+	 * There's other protections that make sure the same lock
+	 * is not taken on the same CPU that lockdep is unaware of.
+	 * Differentiate when it is taken in NMI context.
+	 */
+	raw_spin_lock_irqsave_nested(hlist_lock, *flags, !!in_nmi());
 }
 NOKPROBE_SYMBOL(kretprobe_hash_lock);
 
@@ -1213,7 +1219,13 @@ static void kretprobe_table_lock(unsigned long hash,
 __acquires(hlist_lock)
 {
 	raw_spinlock_t *hlist_lock = kretprobe_table_lock_ptr(hash);
-	raw_spin_lock_irqsave(hlist_lock, *flags);
+	/*
+	 * Nested is a workaround that will soon not be needed.
+	 * There's other protections that make sure the same lock
+	 * is not taken on the same CPU that lockdep is unaware of.
+	 * Differentiate when it is taken in NMI context.
+	 */
+	raw_spin_lock_irqsave_nested(hlist_lock, *flags, !!in_nmi());
 }
 NOKPROBE_SYMBOL(kretprobe_table_lock);
 
@@ -1884,7 +1896,12 @@ static int pre_handler_kretprobe(struct kprobe *p, struct pt_regs *regs)
 
 	/* TODO: consider to only swap the RA after the last pre_handler fired */
 	hash = hash_ptr(current, KPROBE_HASH_BITS);
-	raw_spin_lock_irqsave(&rp->lock, flags);
+	/*
+	 * Nested is a workaround that will soon not be needed.
+	 * There's other protections that make sure the same lock
+	 * is not taken on the same CPU that lockdep is unaware of.
+	 */
+	raw_spin_lock_irqsave_nested(&rp->lock, flags, 1);
 	if (!hlist_empty(&rp->free_instances)) {
 		ri = hlist_entry(rp->free_instances.first,
 				struct kretprobe_instance, hlist);
@@ -1895,7 +1912,7 @@ static int pre_handler_kretprobe(struct kprobe *p, struct pt_regs *regs)
 		ri->task = current;
 
 		if (rp->entry_handler && rp->entry_handler(ri, regs)) {
-			raw_spin_lock_irqsave(&rp->lock, flags);
+			raw_spin_lock_irqsave_nested(&rp->lock, flags, 1);
 			hlist_add_head(&ri->hlist, &rp->free_instances);
 			raw_spin_unlock_irqrestore(&rp->lock, flags);
 			return 0;
Signature · 1 line
2.27.0
Signature · 1 line
Masami Hiramatsu <[email protected]>
author maintainer
#19 lore raw

Re: [PATCH AUTOSEL 4.19 18/21] kprobes: Tell lockdep about kprobe nesting

Quoted 16 lines · Masami Hiramatsu

Hi,

Quoted 11 lines · On Mon, 9 Nov 2020 22:55:38 -0500 Sasha Levin <[email protected]> wrote:

From: "Steven Rostedt (VMware)" <[email protected]>

[ Upstream commit 645f224e7ba2f4200bf163153d384ceb0de5462e ]

Since the kprobe handlers have protection that prohibits other handlers from executing in other contexts (like if an NMI comes in while processing a kprobe, and executes the same kprobe, it will get fail with a "busy" return). Lockdep is unaware of this protection. Use lockdep's nesting api to differentiate between locks taken in INT3 context and other context to suppress the false warnings.

Quoted 8 lines
Quoted 2 lines

This fixes a lockdep false positive warning comes from commit e03b4a084ea6 ("kprobes: Remove NMI context check"). Does anyone report that happen on the stable kernel?

If not, you do not need this patch for stable kernels.

I'll drop it, thanks!

Signature · 2 lines
Thanks,
Sasha
author maintainer
#20 lore raw

PATCH 19/21 selftests: proc: fix warning: _GNU_SOURCE redefined

In reply to Sasha Levin

From: Tommi Rantala <[email protected]>

[ Upstream commit f3ae6c6e8a3ea49076d826c64e63ea78fbf9db43 ]

Makefile already contains -D_GNU_SOURCE, so we can remove it from the *.c files.

---
 tools/testing/selftests/proc/proc-loadavg-001.c  | 1 -
 tools/testing/selftests/proc/proc-self-syscall.c | 1 -
 tools/testing/selftests/proc/proc-uptime-002.c   | 1 -
 3 files changed, 3 deletions(-)
tools/testing/selftests/proc/proc-loadavg-001.c +0 -1
index fcff7047000da..8edaafc2b92fd 100644
@@ -14,7 +14,6 @@
  * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
  */
 /* Test that /proc/loadavg correctly reports last pid in pid namespace. */
-#define _GNU_SOURCE
 #include <errno.h>
 #include <sched.h>
 #include <sys/types.h>
tools/testing/selftests/proc/proc-self-syscall.c +0 -1
index 5ab5f4810e43a..7b9018fad092a 100644
@@ -13,7 +13,6 @@
  * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
  * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
  */
-#define _GNU_SOURCE
 #include <unistd.h>
 #include <sys/syscall.h>
 #include <sys/types.h>
tools/testing/selftests/proc/proc-uptime-002.c +0 -1
index 30e2b78490898..e7ceabed7f51f 100644
@@ -15,7 +15,6 @@
  */
 // Test that values in /proc/uptime increment monotonically
 // while shifting across CPUs.
-#define _GNU_SOURCE
 #undef NDEBUG
 #include <assert.h>
 #include <unistd.h>
Signature · 1 line
2.27.0
author maintainer
#21 lore raw

PATCH 20/21 tpm_tis: Disable interrupts on ThinkPad T490s

In reply to Sasha Levin

From: Jerry Snitselaar <[email protected]>

[ Upstream commit b154ce11ead925de6a94feb3b0317fafeefa0ebc ]

There is a misconfiguration in the bios of the gpio pin used for the interrupt in the T490s. When interrupts are enabled in the tpm_tis driver code this results in an interrupt storm. This was initially reported when we attempted to enable the interrupt code in the tpm_tis driver, which previously wasn't setting a flag to enable it. Due to the reports of the interrupt storm that code was reverted and we went back to polling instead of using interrupts. Now that we know the T490s problem is a firmware issue, add code to check if the system is a T490s and disable interrupts if that is the case. This will allow us to enable interrupts for everyone else. If the user has a fixed bios they can force the enabling of interrupts with tpm_tis.interrupts=1 on the kernel command line.

---
 drivers/char/tpm/tpm_tis.c | 29 +++++++++++++++++++++++++++--
 1 file changed, 27 insertions(+), 2 deletions(-)
drivers/char/tpm/tpm_tis.c +27 -2
index f08949a5f6785..5a3a4f0953910 100644
@@ -31,6 +31,7 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/kernel.h>
+#include <linux/dmi.h>
 #include "tpm.h"
 #include "tpm_tis_core.h"
 
@@ -53,8 +54,8 @@ static inline struct tpm_tis_tcg_phy *to_tpm_tis_tcg_phy(struct tpm_tis_data *da
 	return container_of(data, struct tpm_tis_tcg_phy, priv);
 }
 
-static bool interrupts = true;
-module_param(interrupts, bool, 0444);
+static int interrupts = -1;
+module_param(interrupts, int, 0444);
 MODULE_PARM_DESC(interrupts, "Enable interrupts");
 
 static bool itpm;
@@ -67,6 +68,28 @@ module_param(force, bool, 0444);
 MODULE_PARM_DESC(force, "Force device probe rather than using ACPI entry");
 #endif
 
+static int tpm_tis_disable_irq(const struct dmi_system_id *d)
+{
+	if (interrupts == -1) {
+		pr_notice("tpm_tis: %s detected: disabling interrupts.\n", d->ident);
+		interrupts = 0;
+	}
+
+	return 0;
+}
+
+static const struct dmi_system_id tpm_tis_dmi_table[] = {
+	{
+		.callback = tpm_tis_disable_irq,
+		.ident = "ThinkPad T490s",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad T490s"),
+		},
+	},
+	{}
+};
+
 #if defined(CONFIG_PNP) && defined(CONFIG_ACPI)
 static int has_hid(struct acpi_device *dev, const char *hid)
 {
@@ -196,6 +219,8 @@ static int tpm_tis_init(struct device *dev, struct tpm_info *tpm_info)
 	int irq = -1;
 	int rc;
 
+	dmi_check_system(tpm_tis_dmi_table);
+
 	rc = check_acpi_tpm2(dev);
 	if (rc)
 		return rc;
Signature · 1 line
2.27.0
author maintainer
#22 lore raw

PATCH 21/21 vt: Disable KD_FONT_OP_COPY

In reply to Sasha Levin

From: Daniel Vetter <[email protected]>

[ Upstream commit 3c4e0dff2095c579b142d5a0693257f1c58b4804 ]

It's buggy:

Quoted 7 lines · Minh Yuan

We recently discovered a slab-out-of-bounds read in fbcon in the latest kernel ( v5.10-rc2 for now ). The root cause of this vulnerability is that "fbcon_do_set_font" did not handle "vc->vc_font.data" and "vc->vc_font.height" correctly, and the patch
<https://lkml.org/lkml/2020/9/27/223> for VT_RESIZEX can't handle this issue.

Quoted 6 lines

Specifically, we use KD_FONT_OP_SET to set a small font.data for tty6, and use KD_FONT_OP_SET again to set a large font.height for tty1. After that, we use KD_FONT_OP_COPY to assign tty6's vc_font.data to tty1's vc_font.data in "fbcon_do_set_font", while tty1 retains the original larger height. Obviously, this will cause an out-of-bounds read, because we can access a smaller vc_font.data with a larger vc_font.height.

Further there was only one user ever.
- Android's loadfont, busybox and console-tools only ever use OP_GET and OP_SET
- fbset documentation only mentions the kernel cmdline font: option, not anything else.
- systemd used OP_COPY before release 232 published in Nov 2016

Now unfortunately the crucial report seems to have gone down with gmane, and the commit message doesn't say much. But the pull request hints at OP_COPY being broken

https://github.com/systemd/systemd/pull/3651

So in other words, this never worked, and the only project which foolishly every tried to use it, realized that rather quickly too.

Instead of trying to fix security issues here on dead code by adding missing checks, fix the entire thing by removing the functionality.

Note that systemd code using the OP_COPY function ignored the return value, so it doesn't matter what we're doing here really - just in case a lone server somewhere happens to be extremely unlucky and running an affected old version of systemd. The relevant code from font_copy_to_all_vcs() in systemd was:

	/* copy font from active VT, where the font was uploaded to */
	cfo.op = KD_FONT_OP_COPY;
	cfo.height = vcs.v_active-1; /* tty1 == index 0 */
	(void) ioctl(vcfd, KDFONTOP, &cfo);

Note this just disables the ioctl, garbage collecting the now unused callbacks is left for -next.

v2: Tetsuo found the old mail, which allowed me to find it on another archive. Add the link too.

References: https://lists.freedesktop.org/archives/systemd-devel/2016-June/036935.html
References: https://github.com/systemd/systemd/pull/3651

---
 drivers/tty/vt/vt.c | 24 ++----------------------
 1 file changed, 2 insertions(+), 22 deletions(-)
drivers/tty/vt/vt.c +2 -22
index 758f522f331e4..13ea0579f104c 100644
@@ -4574,27 +4574,6 @@ static int con_font_default(struct vc_data *vc, struct console_font_op *op)
 	return rc;
 }
 
-static int con_font_copy(struct vc_data *vc, struct console_font_op *op)
-{
-	int con = op->height;
-	int rc;
-
-
-	console_lock();
-	if (vc->vc_mode != KD_TEXT)
-		rc = -EINVAL;
-	else if (!vc->vc_sw->con_font_copy)
-		rc = -ENOSYS;
-	else if (con < 0 || !vc_cons_allocated(con))
-		rc = -ENOTTY;
-	else if (con == vc->vc_num)	/* nothing to do */
-		rc = 0;
-	else
-		rc = vc->vc_sw->con_font_copy(vc, con);
-	console_unlock();
-	return rc;
-}
-
 int con_font_op(struct vc_data *vc, struct console_font_op *op)
 {
 	switch (op->op) {
@@ -4605,7 +4584,8 @@ int con_font_op(struct vc_data *vc, struct console_font_op *op)
 	case KD_FONT_OP_SET_DEFAULT:
 		return con_font_default(vc, op);
 	case KD_FONT_OP_COPY:
-		return con_font_copy(vc, op);
+		/* was buggy and never really used */
+		return -EINVAL;
 	}
 	return -ENOSYS;
 }
Signature · 1 line
2.27.0