hwmon: pwm-fan: Fix RPM calculation
PATCH v4 1/1 hwmon: pwm-fan: Fix RPM calculation
To convert the number of pulses counted into an RPM estimation, we need to divide by the width of our measurement interval instead of multiplying by it. If the width of the measurement interval is zero we don't update the RPM value to avoid dividing by zero.
We also don't need to do 64-bit division, with 32-bits we can handle a fan running at over 4 million RPM.
---
Changes from v2:
* Don't update the RPM value if delta=0.
drivers/hwmon/pwm-fan.c | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-)
drivers/hwmon/pwm-fan.c +7 -6
@@ -54,14 +54,15 @@ static irqreturn_t pulse_handler(int irq, void *dev_id)static void sample_timer (struct timer_list *t) {struct pwm_fan_ctx *ctx =from_timer (ctx, t, rpm_timer); +unsigned int delta =ktime_ms_delta (ktime_get (), ctx->sample_start);int pulses; -u64 tmp; - pulses =atomic_read (&ctx->pulses); -atomic_sub (pulses, &ctx->pulses); - tmp = (u64 )pulses *ktime_ms_delta (ktime_get (), ctx->sample_start) *60 ; -do_div (tmp, ctx->pulses_per_revolution *1000 ); - ctx->rpm = tmp; +if (delta) { + pulses =atomic_read (&ctx->pulses); +atomic_sub (pulses, &ctx->pulses); + ctx->rpm = (unsigned int )(pulses *1000 *60 ) / + (ctx->pulses_per_revolution * delta); + } ctx->sample_start =ktime_get ();mod_timer (&ctx->rpm_timer, jiffies +HZ );
base-commit: f8394f232b1eab649ce2df5c5f15b0e528c92091
Signature · 1 line
2.29.2
Guenter Roeck
maintainerQuoted 33 lines · Paul Barker
To convert the number of pulses counted into an RPM estimation, we need to divide by the width of our measurement interval instead of multiplying by it. If the width of the measurement interval is zero we don't update the RPM value to avoid dividing by zero.
We also don't need to do 64-bit division, with 32-bits we can handle a fan running at over 4 million RPM.
Signed-off-by Paul Barker <[email protected]>---
Changes from v2:
* Don't update the RPM value if delta=0.
drivers/hwmon/pwm-fan.c | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-)drivers/hwmon/pwm-fan.c +1
-4@@ -54,14 +54,15 @@ static irqreturn_t pulse_handler(int irq, void *dev_id)static void sample_timer (struct timer_list *t) {struct pwm_fan_ctx *ctx =from_timer (ctx, t, rpm_timer); +unsigned int delta =ktime_ms_delta (ktime_get (), ctx->sample_start);int pulses; -u64 tmp; - pulses =atomic_read (&ctx->pulses); -atomic_sub (pulses, &ctx->pulses); - tmp = (u64 )pulses *ktime_ms_delta (ktime_get (), ctx->sample_start) *60 ;
drivers/hwmon/pwm-fan.c static irqreturn_t pulse_handler(int irq, void *dev_id) · line 67
Quoted 10 lines
drivers/hwmon/pwm-fan.c +6
-2-do_div (tmp, ctx->pulses_per_revolution *1000 ); - ctx->rpm = tmp; +if (delta) { + pulses =atomic_read (&ctx->pulses); +atomic_sub (pulses, &ctx->pulses); + ctx->rpm = (unsigned int )(pulses *1000 *60 ) / + (ctx->pulses_per_revolution * delta); + } ctx->sample_start =ktime_get ();
I know I am a bit nitpicking here, but should ctx->sample_start only be updated if delta != 0 ? We don't reset pulses if delta == 0, meaning the next reading will be based on the old start time (even if the difference was less than 1 ms).
Thanks,
Guenter
Quoted 6 lines
drivers/hwmon/pwm-fan.c +0
-0mod_timer (&ctx->rpm_timer, jiffies +HZ );base-commit:
f8394f232b1eab649ce2df5c5f15b0e528c92091Signature · 1 line
2.29.2