Skip to contentSkip to conversation

ARM: dts: aspeed: amd-ethanolx: Enable KCS channel 3

PATCH Applied Konstantin Aladyshev 2 participants 4 messages Nov 11, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 ARM: dts: aspeed: amd-ethanolx: Enable KCS channel 3

The KCS interface on the LPC channel 3 in the controller is used for the in-band BMC<->BIOS IPMI communication. 0xCA2 is a default host CPU LPC IO address for this interface.

---
 arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts | 5 +++++
 1 file changed, 5 insertions(+)
arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts +5 -0
index 89ddc3847222..2a86bda8afd8 100644
@@ -147,6 +147,11 @@
 	aspeed,lpc-io-reg = <0x62>;
 };
 
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xCA2>;
+};
+
 &kcs4 {
 	status = "okay";
 	aspeed,lpc-io-reg = <0x97DE>;
Signature · 1 line
2.17.1
#1 lore raw

PATCH 2/3 ARM: dts: aspeed: amd-ethanolx: Enable devices for the iKVM functionality

Enable the USB 2.0 Virtual Hub Controller and
the Video Engine with it's reserved memory region for the implementation of the iKVM functionality in the BMC.

---
 arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)
arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts +22 -0
index 2a86bda8afd8..b93ed44eba0c 100644
@@ -13,6 +13,21 @@
 	memory@80000000 {
 		reg = <0x80000000 0x20000000>;
 	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+
 	aliases {
 		serial0 = &uart1;
 		serial4 = &uart5;
@@ -220,5 +235,12 @@
 	};
 };
 
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
 
+&vhub {
+	status = "okay";
+};
 
Signature · 1 line
2.17.1
#2 lore raw

PATCH 3/3 ARM: dts: aspeed: amd-ethanolx: Add GPIO line names

In reply to Konstantin Aladyshev

Add GPIO line names for AMD EthanolX customer reference board. It populates AST2500 GPIO lines (A0-A7 to AC0-AC7) with AMD EthanolX designated names.

---
 arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts | 44 +++++++++++++++++++
 1 file changed, 44 insertions(+)
arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts +44 -0
index b93ed44eba0c..96ff0aea64e5 100644
@@ -97,6 +97,50 @@
 		     &pinctrl_adc4_default>;
 };
 
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"","","FAULT_LED","CHASSIS_ID_LED","","","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"CHASSIS_ID_BTN","INTRUDER","AC_LOSS","","","","","",
+	/*D0-D7*/	"HDT_DBREQ","LOCAL_SPI_ROM_SEL","FPGA_SPI_ROM_SEL","JTAG_MUX_S",
+			"JTAG_MUX_OE","HDT_SEL","ASERT_WARM_RST_BTN","FPGA_RSVD",
+	/*E0-E7*/	"","","MON_P0_PWR_BTN","MON_P0_RST_BTN","MON_P0_NMI_BTN",
+			"MON_P0_PWR_GOOD","MON_PWROK","MON_RESET",
+	/*F0-F7*/	"MON_P0_PROCHOT","MON_P1_PROCHOT","MON_P0_THERMTRIP",
+			"MON_P1_THERMTRIP","P0_PRESENT","P1_PRESENT","MON_ATX_PWR_OK","",
+	/*G0-G7*/	"BRD_REV_ID_3","BRD_REV_ID_2","BRD_REV_ID_1","BRD_REV_ID_0",
+			"P0_APML_ALERT","P1_APML_ALERT","FPGA ALERT","",
+	/*H0-H7*/	"BRD_ID_0","BRD_ID_1","BRD_ID_2","BRD_ID_3",
+			"PCIE_DISCONNECTED","USB_DISCONNECTED","SPARE_0","SPARE_1",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"ASSERT_PWR_BTN","ASSERT_RST_BTN","ASSERT_NMI_BTN",
+			"ASSERT_LOCAL_LOCK","ASSERT_P0_PROCHOT","ASSERT_P1_PROCHOT",
+			"ASSERT_CLR_CMOS","ASSERT_BMC_READY",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"P0_VDD_CORE_RUN_VRHOT","P0_VDD_SOC_RUN_VRHOT",
+			"P0_VDD_MEM_ABCD_SUS_VRHOT","P0_VDD_MEM_EFGH_SUS_VRHOT",
+			"P1_VDD_CORE_RUN_VRHOT","P1_VDD_SOC_RUN_VRHOT",
+			"P1_VDD_MEM_ABCD_SUS_VRHOT","P1_VDD_MEM_EFGH_SUS_VRHOT",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"","SENSOR THERM","","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
 //APML for P0
 &i2c0 {
 	status = "okay";
Signature · 1 line
2.17.1
maintainer Applied
#3 lore raw
In reply to Konstantin Aladyshev
Quoted 11 lines · Konstantin Aladyshev

The KCS interface on the LPC channel 3 in the controller is used for the in-band BMC<->BIOS IPMI communication. 0xCA2 is a default host CPU LPC IO address for this interface.

I've merged this series into dev-5.8.

Cheers,

Joel

Quoted 23 lines
---
 arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts | 5 +++++
 1 file changed, 5 insertions(+)
arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts +5 -1
index 89ddc3847222..2a86bda8afd8 100644
@@ -147,6 +147,11 @@
        aspeed,lpc-io-reg = <0x62>;
 };
 
+&kcs3 {
+       status = "okay";
+       aspeed,lpc-io-reg = <0xCA2>;
+};
+
 &kcs4 {
        status = "okay";
        aspeed,lpc-io-reg = <0x97DE>;
--

2.17.1