Skip to contentSkip to conversation

Set cqe off during suspend flow

PATCH In review Wenbin Mei 2 participants 6 messages Nov 12, 2020 – Nov 18, 2020

Subsystems (3)
lore
Share & tools
lore

Wenbin Mei

author
#0 lore raw

cover Set cqe off during suspend flow

Wenbin Mei (3):
dt-bindings: mmc: Add optional cqe off properties
arm64: dts: mt8192: Add cqe off flag
mmc: core: Set cqe off during suspend flow
---
This patch depends on
[PATCH v7 3/4] arm64: dts: mt8192: add mmc device node

Please also accept this patch together with [1]
to avoid build and dt binding check error.
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=364279

---
 Documentation/devicetree/bindings/mmc/mmc-controller.yaml | 7 +++++++
 arch/arm64/boot/dts/mediatek/mt8192-evb.dts               | 1 +
 drivers/mmc/core/host.c                                   | 2 ++
 drivers/mmc/core/mmc.c                                    | 5 +++++
 include/linux/mmc/pm.h                                    | 1 +
 5 files changed, 16 insertions(+)

--
2.18.0

author
#1 lore raw

PATCH 1/3 dt-bindings: mmc: Add optional cqe off properties

Add optional properties for cqe hosts which are used to set cqe off during suspend flow.

---
 Documentation/devicetree/bindings/mmc/mmc-controller.yaml | 7 +++++++
 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/mmc/mmc-controller.yaml +7 -0
index b96da0c7f819..457c9a84b988 100644
@@ -164,6 +164,13 @@ properties:
     description:
       enable SDIO IRQ signalling on this interface
 
+  cqe-off-in-suspend:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      After suspend, the mmc host is powered off by HW, and bring CQE register
+      to default state, so we add the flag to re-init CQE register after resume
+      back.
+
   full-pwr-cycle:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
Signature · 1 line
2.18.0
maintainer
#2 lore raw

Re: [PATCH v1 1/3] dt-bindings: mmc: Add optional cqe off properties

Quoted 13 lines · Wenbin Mei

Add optional properties for cqe hosts which are used to set cqe off during suspend flow.

---
 Documentation/devicetree/bindings/mmc/mmc-controller.yaml | 7 +++++++
 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/mmc/mmc-controller.yaml +0 -0
index b96da0c7f819..457c9a84b988 100644

Documentation/devicetree/bindings/mmc/mmc-controller.yaml properties: · line 172

Quoted 9 lines
Documentation/devicetree/bindings/mmc/mmc-controller.yaml +6 -0
@@ -164,6 +164,13 @@ properties:
     description:
       enable SDIO IRQ signalling on this interface
 
+  cqe-off-in-suspend:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      After suspend, the mmc host is powered off by HW, and bring CQE register
+      to default state, so we add the flag to re-init CQE register after resume
+      back.

The driver change is before suspend, but this says on resume...

In any case, this should be implied by the SoC specific compatible.

Quoted 7 lines
Documentation/devicetree/bindings/mmc/mmc-controller.yaml +1 -0
+
   full-pwr-cycle:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
Signature · 1 line
2.18.0
author
#3 lore raw

Re: [PATCH v1 1/3] dt-bindings: mmc: Add optional cqe off properties

Quoted 26 lines · Rob Herring
Quoted 13 lines · Wenbin Mei

Add optional properties for cqe hosts which are used to set cqe off during suspend flow.

---
 Documentation/devicetree/bindings/mmc/mmc-controller.yaml | 7 +++++++
 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/mmc/mmc-controller.yaml +0 -0
index b96da0c7f819..457c9a84b988 100644

Documentation/devicetree/bindings/mmc/mmc-controller.yaml properties: · line 172

Quoted 9 lines
Documentation/devicetree/bindings/mmc/mmc-controller.yaml +6 -0
@@ -164,6 +164,13 @@ properties:
     description:
       enable SDIO IRQ signalling on this interface
 
+  cqe-off-in-suspend:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      After suspend, the mmc host is powered off by HW, and bring CQE register
+      to default state, so we add the flag to re-init CQE register after resume
+      back.

The driver change is before suspend, but this says on resume...

Quoted 2 lines

In any case, this should be implied by the SoC specific compatible.

Thanks for your reply, I will drop this patchset, and resend another patchset for this issue.

Quoted 7 lines
Quoted 7 lines
Documentation/devicetree/bindings/mmc/mmc-controller.yaml +1 -0
+
   full-pwr-cycle:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
Signature · 1 line
2.18.0

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

author
#4 lore raw

PATCH 2/3 arm64: dts: mt8192: Add cqe off flag

In reply to Wenbin Mei

Add cqe off flag for MT8192 mmc nodes.

---
 arch/arm64/boot/dts/mediatek/mt8192-evb.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/mediatek/mt8192-evb.dts +1 -0
index a4279fa87c2b..0df78e4ea0d0 100644
@@ -41,6 +41,7 @@
 	mmc-hs400-1_8v;
 	supports-cqe;
 	cap-mmc-hw-reset;
+	cqe-off-in-suspend;
 	no-sdio;
 	no-sd;
 	hs400-ds-delay = <0x12814>;
Signature · 1 line
2.18.0
author
#5 lore raw

PATCH 3/3 mmc: core: Set cqe off during suspend flow

In reply to Wenbin Mei

Before we got these errors on MT8192 platform:

[   59.153891] Restarting tasks ...
[   59.154540] done.
[   59.159175] PM: suspend exit
[   59.218724] mtk-msdc 11f60000.mmc: phase: [map:fffffffe] [maxlen:31]
[final:16]
[  119.776083] mmc0: cqhci: timeout for tag 9
[  119.780196] mmc0: cqhci: ============ CQHCI REGISTER DUMP ===========
[  119.786709] mmc0: cqhci: Caps:      0x100020b6 | Version:  0x00000510
[  119.793225] mmc0: cqhci: Config:    0x00000101 | Control:  0x00000000
[  119.799706] mmc0: cqhci: Int stat:  0x00000000 | Int enab: 0x00000000
[  119.806177] mmc0: cqhci: Int sig:   0x00000000 | Int Coal: 0x00000000
[  119.812670] mmc0: cqhci: TDL base:  0x00000000 | TDL up32: 0x00000000
[  119.819149] mmc0: cqhci: Doorbell:  0x003ffc00 | TCN:      0x00000200
[  119.825656] mmc0: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
[  119.832155] mmc0: cqhci: Task clr:  0x00000000 | SSC1:     0x00001000
[  119.838627] mmc0: cqhci: SSC2:      0x00000000 | DCMD rsp: 0x00000000
[  119.845174] mmc0: cqhci: RED mask:  0xfdf9a080 | TERRI:    0x0000891c
[  119.851654] mmc0: cqhci: Resp idx:  0x00000000 | Resp arg: 0x00000000
[  119.865773] mmc0: cqhci: : ===========================================
[  119.872358] mmc0: running CQE recovery

From these logs, we found TDL base was back to the default value.

After suspend, the mmc host is powered off by HW, and bring CQE register to the default value, so CQE need to be re-initialized after resuming back.

---
 drivers/mmc/core/host.c | 2 ++
 drivers/mmc/core/mmc.c  | 5 +++++
 include/linux/mmc/pm.h  | 1 +
 3 files changed, 8 insertions(+)
drivers/mmc/core/host.c +2 -0
index ce43f7573d80..c98486c8fb3b 100644
@@ -284,6 +284,8 @@ int mmc_of_parse(struct mmc_host *host)
 	if (device_property_read_bool(dev, "wakeup-source") ||
 	    device_property_read_bool(dev, "enable-sdio-wakeup")) /* legacy */
 		host->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
+	if (device_property_read_bool(dev, "cqe-off-in-suspend"))
+		host->pm_caps |= MMC_PM_CQE_OFF_IN_SUSPEND;
 	if (device_property_read_bool(dev, "mmc-ddr-3_3v"))
 		host->caps |= MMC_CAP_3_3V_DDR;
 	if (device_property_read_bool(dev, "mmc-ddr-1_8v"))
drivers/mmc/core/mmc.c +5 -0
index b3fa193de846..f5ae1f13a867 100644
@@ -2047,6 +2047,11 @@ static int _mmc_suspend(struct mmc_host *host, bool is_suspend)
 		err = mmc_deselect_cards(host);
 
 	if (!err) {
+		if (host->cqe_enabled &&
+		    (host->pm_caps & MMC_PM_CQE_OFF_IN_SUSPEND)) {
+			host->cqe_ops->cqe_disable(host);
+			host->cqe_enabled = false;
+		}
 		mmc_power_off(host);
 		mmc_card_set_suspended(host->card);
 	}
include/linux/mmc/pm.h +1 -0
index 3549f8045784..3dd1046f2c8f 100644
@@ -23,5 +23,6 @@ typedef unsigned int mmc_pm_flag_t;
 
 #define MMC_PM_KEEP_POWER	(1 << 0)	/* preserve card power during suspend */
 #define MMC_PM_WAKE_SDIO_IRQ	(1 << 1)	/* wake up host system on SDIO IRQ assertion */
+#define MMC_PM_CQE_OFF_IN_SUSPEND  (1 << 2)	/* cqe off during suspend */
 
 #endif /* LINUX_MMC_PM_H */
Signature · 1 line
2.18.0