Skip to contentSkip to conversation

Extend irqchip ocelot driver to support other SoCs

PATCH Superseded Gregory CLEMENT 2 participants 8 messages Nov 12, 2020 – Nov 16, 2020

Subsystems (2)

v2 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v2 cover Extend irqchip ocelot driver to support other SoCs

Hello,

Ocelot SoC belongs to a larger family of SoCs which use the same interrupt controller with a few variation.

This series of patches add support for Luton, Serval and Jaguar2, they are all MIPS based.

The first patches of the series also updates the binding documentation with the new compatible strings.

Gregory

Changelog:
v1 -> v2:
- Convert the binding to yaml
- Squashed the patches adding new binding in a single one

Gregory CLEMENT (5):
dt-bindings: interrupt-controller: convert icpu intr bindings to
json-schema
dt-bindings: interrupt-controller: Add binding for few Microsemi
interrupt controllers
irqchip: ocelot: Add support for Luton platforms
irqchip: ocelot: Add support for Serval platforms
irqchip: ocelot: Add support for Jaguar2 platforms

 .../mscc,ocelot-icpu-intr.txt                 |  21 --
 .../mscc,ocelot-icpu-intr.yaml                |  63 ++++++
 drivers/irqchip/irq-mscc-ocelot.c             | 183 ++++++++++++++++--
 3 files changed, 225 insertions(+), 42 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.yaml
Signature · 1 line
2.28.0
#1 lore raw

PATCH v2 1/5 dt-bindings: interrupt-controller: convert icpu intr bindings to json-schema

Convert device tree bindings for Microsemi Ocelot SoC ICPU Interrupt Controller to YAML format

---
 .../mscc,ocelot-icpu-intr.txt                 | 21 -------
 .../mscc,ocelot-icpu-intr.yaml                | 59 +++++++++++++++++++
 2 files changed, 59 insertions(+), 21 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.yaml
Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.txt deleted +0 -21
deleted file mode 100644
index f5baeccb689f..000000000000
@@ -1,21 +0,0 @@
-Microsemi Ocelot SoC ICPU Interrupt Controller
-
-Required properties:
-
-- compatible : should be "mscc,ocelot-icpu-intr"
-- reg : Specifies base physical address and size of the registers.
-- interrupt-controller : Identifies the node as an interrupt controller
-- #interrupt-cells : Specifies the number of cells needed to encode an
-  interrupt source. The value shall be 1.
-- interrupts : Specifies the CPU interrupt the controller is connected to.
-
-Example:
-
-		intc: interrupt-controller@70000070 {
-			compatible = "mscc,ocelot-icpu-intr";
-			reg = <0x70000070 0x70>;
-			#interrupt-cells = <1>;
-			interrupt-controller;
-			interrupt-parent = <&cpuintc>;
-			interrupts = <2>;
-		};
Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.yaml new file +59 -0

60 lines not on this page · raw message

Signature · 1 line
2.28.0
maintainer
#2 lore raw

Re: [PATCH v2 1/5] dt-bindings: interrupt-controller: convert icpu intr bindings to json-schema

Quoted 11 lines · Gregory CLEMENT

Convert device tree bindings for Microsemi Ocelot SoC ICPU Interrupt Controller to YAML format

---
 .../mscc,ocelot-icpu-intr.txt                 | 21 -------
 .../mscc,ocelot-icpu-intr.yaml                | 59 +++++++++++++++++++
 2 files changed, 59 insertions(+), 21 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.yaml

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:
./Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.yaml:59:4: [error] no new line character at the end of file (new-line-at-end-of-file)

dtschema/dtc warnings/errors:
make[1]: *** [Documentation/devicetree/bindings/Makefile:59: Documentation/devicetree/bindings/processed-schema-examples.json] Error 123
make: *** [Makefile:1364: dt_binding_check] Error 2

See https://patchwork.ozlabs.org/patch/1399077

The base for the patch is generally the last rc1. Any dependencies should be noted.

If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date:

pip3 install dtschema --upgrade

Please check and re-submit.

#3 lore raw

Re: [PATCH v2 1/5] dt-bindings: interrupt-controller: convert icpu intr bindings to json-schema

Hello Rob,

Quoted 24 lines · Gregory CLEMENT
Quoted 11 lines

Convert device tree bindings for Microsemi Ocelot SoC ICPU Interrupt Controller to YAML format

---
 .../mscc,ocelot-icpu-intr.txt                 | 21 -------
 .../mscc,ocelot-icpu-intr.yaml                | 59 +++++++++++++++++++
 2 files changed, 59 insertions(+), 21 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.yaml

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:
./Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.yaml:59:4: [error] no new line character at the end of file (new-line-at-end-of-file)

dtschema/dtc warnings/errors:
make[1]: *** [Documentation/devicetree/bindings/Makefile:59: Documentation/devicetree/bindings/processed-schema-examples.json] Error 123
make: *** [Makefile:1364: dt_binding_check] Error 2

Quoted 8 lines

See https://patchwork.ozlabs.org/patch/1399077

The base for the patch is generally the last rc1. Any dependencies should be noted.

If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date:

I actually ran 'make dt_binding_check' and in the documentation there was no reference of Documentation/devicetree/writing-schema.rst the need of 'yamllint' while in the dependencies section of it was mentioned the need of 'libyaml-dev'.

What do you think about updating the documentation ?

Quoted 4 lines

pip3 install dtschema --upgrade

Please check and re-submit.

Sure I am doing it right now.

Gregory

Quoted 1 line
Signature · 3 lines
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
#4 lore raw

PATCH v2 2/5 dt-bindings: interrupt-controller: Add binding for few Microsemi interrupt controllers

In reply to Gregory CLEMENT

Add the Device Tree binding documentation for the Microsemi Jaguar2, Luton and Serval interrupt controller that is part of the ICPU. It is connected directly to the MIPS core interrupt controller.

---
 .../bindings/interrupt-controller/mscc,ocelot-icpu-intr.yaml  | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/interrupt-controller/mscc,ocelot-icpu-intr.yaml +4 -0
index afd00f9c9d74..e2f093faa906 100644
@@ -21,7 +21,11 @@ properties:
   compatible:
     items:
       - enum:
+          - mscc,jaguar2-icpu-intr
+          - mscc,luton-icpu-intr
           - mscc,ocelot-icpu-intr
+          - mscc,serval-icpu-intr
+
 
   '#interrupt-cells':
     const: 1
Signature · 1 line
2.28.0
#5 lore raw

PATCH v2 3/5 irqchip: ocelot: Add support for Luton platforms

In reply to Gregory CLEMENT

This patch extends irqchip driver for oceleot to be used with an other vcoreiii base platform: Luton.

Based on a larger patch from Lars Povlsen <[email protected]>

---
 drivers/irqchip/irq-mscc-ocelot.c | 145 +++++++++++++++++++++++++-----
 1 file changed, 123 insertions(+), 22 deletions(-)
drivers/irqchip/irq-mscc-ocelot.c +123 -22
index 88143c0b700c..9964800c53c2 100644
@@ -12,39 +12,115 @@
 #include <linux/irqchip/chained_irq.h>
 #include <linux/interrupt.h>
 
-#define ICPU_CFG_INTR_INTR_STICKY	0x10
-#define ICPU_CFG_INTR_INTR_ENA		0x18
-#define ICPU_CFG_INTR_INTR_ENA_CLR	0x1c
-#define ICPU_CFG_INTR_INTR_ENA_SET	0x20
-#define ICPU_CFG_INTR_DST_INTR_IDENT(x)	(0x38 + 0x4 * (x))
-#define ICPU_CFG_INTR_INTR_TRIGGER(x)	(0x5c + 0x4 * (x))
-
-#define OCELOT_NR_IRQ 24
+#define ICPU_CFG_INTR_DST_INTR_IDENT(_p, x)	(_p->reg_off_ident + 0x4 * (x))
+#define ICPU_CFG_INTR_INTR_TRIGGER(_p, x)	(_p->reg_off_trigger + 0x4 * (x))
+
+#define FLAGS_NEED_INIT_ENABLE	BIT(0)
+#define FLAGS_FORCE_LUTON_STYLE	BIT(1)
+#define FLAGS_HAS_TRIGGER	BIT(2)
+
+struct chip_props {
+	u32 flags;
+	u32 reg_off_sticky;
+	u32 reg_off_ena;
+	u32 reg_off_ena_clr;
+	u32 reg_off_ena_set;
+	u32 reg_off_ident;
+	u32 reg_off_trigger;
+	u32 reg_off_force;
+	u32 reg_off_ena_irq0;
+	u32 n_irq;
+};
+
+static const struct chip_props ocelot_props = {
+	.flags			= FLAGS_HAS_TRIGGER,
+	.reg_off_sticky		= 0x10,
+	.reg_off_ena		= 0x18,
+	.reg_off_ena_clr	= 0x1c,
+	.reg_off_ena_set	= 0x20,
+	.reg_off_ident		= 0x38,
+	.reg_off_trigger	= 0x5c,
+	.reg_off_force		= 0xc,
+	.n_irq			= 24,
+};
+
+static const struct chip_props luton_props = {
+	.flags			= FLAGS_NEED_INIT_ENABLE |
+				  FLAGS_FORCE_LUTON_STYLE,
+	.reg_off_sticky		= 0,
+	.reg_off_ena		= 0x4,
+	.reg_off_ena_clr	= 0x8,
+	.reg_off_ena_set	= 0xc,
+	.reg_off_ident		= 0x18,
+	.reg_off_trigger	= 0,
+	.reg_off_force		= 0x38,
+	.reg_off_ena_irq0	= 0x14,
+	.n_irq			= 28,
+};
 
 static void ocelot_irq_unmask(struct irq_data *data)
 {
 	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(data);
+	struct irq_domain *d = data->domain;
+	struct chip_props *p = d->host_data;
 	struct irq_chip_type *ct = irq_data_get_chip_type(data);
 	unsigned int mask = data->mask;
 	u32 val;
 
 	irq_gc_lock(gc);
-	val = irq_reg_readl(gc, ICPU_CFG_INTR_INTR_TRIGGER(0)) |
-	      irq_reg_readl(gc, ICPU_CFG_INTR_INTR_TRIGGER(1));
-	if (!(val & mask))
-		irq_reg_writel(gc, mask, ICPU_CFG_INTR_INTR_STICKY);
+	if (p->flags & FLAGS_HAS_TRIGGER) {
+		val = irq_reg_readl(gc, ICPU_CFG_INTR_INTR_TRIGGER(p, 0)) |
+			irq_reg_readl(gc, ICPU_CFG_INTR_INTR_TRIGGER(p, 1));
+		if (!(val & mask))
+			irq_reg_writel(gc, mask, p->reg_off_sticky);
+	}
 
 	*ct->mask_cache &= ~mask;
-	irq_reg_writel(gc, mask, ICPU_CFG_INTR_INTR_ENA_SET);
+	irq_reg_writel(gc, mask, p->reg_off_ena_set);
 	irq_gc_unlock(gc);
 }
 
+static void luton_irq_force(struct irq_data *data,
+			    struct irq_chip_generic *gc,
+			    struct chip_props *p)
+{
+	int off = p->reg_off_force + (data->hwirq * sizeof(u32));
+	u32 val = irq_reg_readl(gc, off);
+
+	irq_reg_writel(gc, val | BIT(3), off);
+}
+
+static int ocelot_irq_force(struct irq_data *data,
+			    enum irqchip_irq_state which, bool state)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(data);
+	struct irq_domain *d = data->domain;
+	struct chip_props *p = d->host_data;
+	int ret = -EINVAL;
+
+	/* Only supports triggering */
+	if ((which == IRQCHIP_STATE_PENDING ||
+	     which == IRQCHIP_STATE_ACTIVE) &&
+	    state && p->reg_off_force) {
+		if (p->flags & FLAGS_FORCE_LUTON_STYLE)
+			/* Config register style */
+			luton_irq_force(data, gc, p);
+		else
+			/* New, bitmask style */
+			irq_reg_writel(gc, data->mask, p->reg_off_force);
+		ret = 0;
+	}
+
+	return ret;
+}
+
 static void ocelot_irq_handler(struct irq_desc *desc)
 {
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 	struct irq_domain *d = irq_desc_get_handler_data(desc);
+	struct chip_props *p = d->host_data;
 	struct irq_chip_generic *gc = irq_get_domain_generic_chip(d, 0);
-	u32 reg = irq_reg_readl(gc, ICPU_CFG_INTR_DST_INTR_IDENT(0));
+	u32 reg = irq_reg_readl(gc, ICPU_CFG_INTR_DST_INTR_IDENT(p, 0));
 
 	chained_irq_enter(chip, desc);
 
@@ -58,25 +134,28 @@ static void ocelot_irq_handler(struct irq_desc *desc)
 	chained_irq_exit(chip, desc);
 }
 
-static int __init ocelot_irq_init(struct device_node *node,
-				  struct device_node *parent)
+static int __init vcoreiii_irq_init(struct device_node *node,
+				    struct device_node *parent,
+				    const struct chip_props *p)
 {
 	struct irq_domain *domain;
 	struct irq_chip_generic *gc;
 	int parent_irq, ret;
 
+	pr_info("%s: Load, %d irqs\n", node->name, p->n_irq);
+
 	parent_irq = irq_of_parse_and_map(node, 0);
 	if (!parent_irq)
 		return -EINVAL;
 
-	domain = irq_domain_add_linear(node, OCELOT_NR_IRQ,
+	domain = irq_domain_add_linear(node, p->n_irq,
 				       &irq_generic_chip_ops, NULL);
 	if (!domain) {
 		pr_err("%pOFn: unable to add irq domain\n", node);
 		return -ENOMEM;
 	}
 
-	ret = irq_alloc_domain_generic_chips(domain, OCELOT_NR_IRQ, 1,
+	ret = irq_alloc_domain_generic_chips(domain, p->n_irq, 1,
 					     "icpu", handle_level_irq,
 					     0, 0, 0);
 	if (ret) {
@@ -92,16 +171,23 @@ static int __init ocelot_irq_init(struct device_node *node,
 		goto err_gc_free;
 	}
 
-	gc->chip_types[0].regs.ack = ICPU_CFG_INTR_INTR_STICKY;
-	gc->chip_types[0].regs.mask = ICPU_CFG_INTR_INTR_ENA_CLR;
+	gc->chip_types[0].regs.ack = p->reg_off_sticky;
+	gc->chip_types[0].regs.mask = p->reg_off_ena_clr;
 	gc->chip_types[0].chip.irq_ack = irq_gc_ack_set_bit;
 	gc->chip_types[0].chip.irq_mask = irq_gc_mask_set_bit;
 	gc->chip_types[0].chip.irq_unmask = ocelot_irq_unmask;
+	gc->chip_types[0].chip.irq_unmask = ocelot_irq_unmask;
+	gc->chip_types[0].chip.irq_set_irqchip_state = ocelot_irq_force;
 
 	/* Mask and ack all interrupts */
-	irq_reg_writel(gc, 0, ICPU_CFG_INTR_INTR_ENA);
-	irq_reg_writel(gc, 0xffffffff, ICPU_CFG_INTR_INTR_STICKY);
+	irq_reg_writel(gc, 0, p->reg_off_ena);
+	irq_reg_writel(gc, 0xffffffff, p->reg_off_sticky);
+
+	/* Overall init */
+	if (p->flags & FLAGS_NEED_INIT_ENABLE)
+		irq_reg_writel(gc, BIT(0), p->reg_off_ena_irq0);
 
+	domain->host_data = (void *)p;
 	irq_set_chained_handler_and_data(parent_irq, ocelot_irq_handler,
 					 domain);
 
@@ -115,4 +201,19 @@ static int __init ocelot_irq_init(struct device_node *node,
 
 	return ret;
 }
+
+static int __init ocelot_irq_init(struct device_node *node,
+				  struct device_node *parent)
+{
+	return vcoreiii_irq_init(node, parent, &ocelot_props);
+}
+
 IRQCHIP_DECLARE(ocelot_icpu, "mscc,ocelot-icpu-intr", ocelot_irq_init);
+
+static int __init luton_irq_init(struct device_node *node,
+				 struct device_node *parent)
+{
+	return vcoreiii_irq_init(node, parent, &luton_props);
+}
+
+IRQCHIP_DECLARE(luton_icpu, "mscc,luton-icpu-intr", luton_irq_init);
Signature · 1 line
2.28.0
#6 lore raw

PATCH v2 4/5 irqchip: ocelot: Add support for Serval platforms

In reply to Gregory CLEMENT

This patch extends irqchip driver for ocelot to be used with an other vcoreiii base platform: Serval.

Based on a larger patch from Lars Povlsen <[email protected]>

---
 drivers/irqchip/irq-mscc-ocelot.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
drivers/irqchip/irq-mscc-ocelot.c +20 -0
index 9964800c53c2..584af3b0a9e2 100644
@@ -44,6 +44,18 @@ static const struct chip_props ocelot_props = {
 	.n_irq			= 24,
 };
 
+static const struct chip_props serval_props = {
+	.flags			= FLAGS_HAS_TRIGGER,
+	.reg_off_sticky		= 0xc,
+	.reg_off_ena		= 0x14,
+	.reg_off_ena_clr	= 0x18,
+	.reg_off_ena_set	= 0x1c,
+	.reg_off_ident		= 0x20,
+	.reg_off_trigger	= 0x4,
+	.reg_off_force		= 0x8,
+	.n_irq			= 24,
+};
+
 static const struct chip_props luton_props = {
 	.flags			= FLAGS_NEED_INIT_ENABLE |
 				  FLAGS_FORCE_LUTON_STYLE,
@@ -210,6 +222,14 @@ static int __init ocelot_irq_init(struct device_node *node,
 
 IRQCHIP_DECLARE(ocelot_icpu, "mscc,ocelot-icpu-intr", ocelot_irq_init);
 
+static int __init serval_irq_init(struct device_node *node,
+				  struct device_node *parent)
+{
+	return vcoreiii_irq_init(node, parent, &serval_props);
+}
+
+IRQCHIP_DECLARE(serval_icpu, "mscc,serval-icpu-intr", serval_irq_init);
+
 static int __init luton_irq_init(struct device_node *node,
 				 struct device_node *parent)
 {
Signature · 1 line
2.28.0
#7 lore raw

PATCH v2 5/5 irqchip: ocelot: Add support for Jaguar2 platforms

In reply to Gregory CLEMENT

This patch extends irqchip driver for ocelot to be used with an other vcoreiii base platform: Jaguar2.

Based on a larger patch from Lars Povlsen <[email protected]>

---
 drivers/irqchip/irq-mscc-ocelot.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
drivers/irqchip/irq-mscc-ocelot.c +20 -0
index 584af3b0a9e2..0dfea8771172 100644
@@ -70,6 +70,18 @@ static const struct chip_props luton_props = {
 	.n_irq			= 28,
 };
 
+static const struct chip_props jaguar2_props = {
+	.flags			= FLAGS_HAS_TRIGGER,
+	.reg_off_sticky		= 0x10,
+	.reg_off_ena		= 0x18,
+	.reg_off_ena_clr	= 0x1c,
+	.reg_off_ena_set	= 0x20,
+	.reg_off_ident		= 0x38,
+	.reg_off_trigger	= 0x5c,
+	.reg_off_force		= 0xc,
+	.n_irq			= 29,
+};
+
 static void ocelot_irq_unmask(struct irq_data *data)
 {
 	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(data);
@@ -237,3 +249,11 @@ static int __init luton_irq_init(struct device_node *node,
 }
 
 IRQCHIP_DECLARE(luton_icpu, "mscc,luton-icpu-intr", luton_irq_init);
+
+static int __init jaguar2_irq_init(struct device_node *node,
+				   struct device_node *parent)
+{
+	return vcoreiii_irq_init(node, parent, &jaguar2_props);
+}
+
+IRQCHIP_DECLARE(jaguar2_icpu, "mscc,jaguar2-icpu-intr", jaguar2_irq_init);
Signature · 1 line
2.28.0