media: i2c: OV8865 image sensor support
Subsystems (4)
v2 cover media: i2c: OV8865 image sensor support
This series adds support for the OV8865 image sensor, as a V4L2 subdev driver. Although an initial series was submitted by Kévin L'hôpital some weeks ago, this version is significantly new and should be considered a new series.
The final patch (not for merge) shows how to enable the OV8865 on the Banana Pi Camera Board v2 with the Banana Pi M3.
Changes since v1:
- Used runtime pm;
- Used assigned-clock-rate;
- Removed clock name;
- Returned closest size in set_fmt;
- Removed unneeded references to v4l2 controls;
- Removed unneeded structure packing attribute;
- Removed i2c device table;
- Dual-licensed bindings;
- Used SPDX tags.
Cheers,
Paul
Kévin L'hôpital (1):
ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
Paul Kocialkowski (2):
dt-bindings: media: i2c: Add OV8865 bindings documentation
media: i2c: Add support for the OV8865 image sensor
.../bindings/media/i2c/ovti,ov8865.yaml | 120 + arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 99 + drivers/media/i2c/Kconfig | 13 + drivers/media/i2c/Makefile | 1 + drivers/media/i2c/ov8865.c | 3043 +++++++++++++++++ 5 files changed, 3276 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml create mode 100644 drivers/media/i2c/ov8865.c
Signature · 1 line
2.28.0
PATCH v2 1/3 dt-bindings: media: i2c: Add OV8865 bindings documentation
This introduces YAML bindings documentation for the OV8865 image sensor.
--- .../bindings/media/i2c/ovti,ov8865.yaml | 120 ++++++++++++++++++ 1 file changed, 120 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml
Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml new file +120 -0
@@ -0,0 +1,120 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov8865.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV8865 Image Sensor Device Tree Bindings + +maintainers: + - Paul Kocialkowski <[email protected]> + +properties: + compatible: + const: ovti,ov8865 + + reg: + maxItems: 1 + + clocks: + items: + - description: EXTCLK Clock + + assigned-clocks: + maxItems: 1 + + assigned-clock-rates: + maxItems: 1 + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply (internal AVDD is used if missing) + + dovdd-supply: + description: I/O Domain Power Supply + + powerdown-gpios: + maxItems: 1 + description: Power Down Pin GPIO Control (active low) + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + type: object + description: MIPI CSI-2 transmitter port + + properties: + endpoint: + type: object + + properties: + remote-endpoint: true + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - bus-type + - data-lanes + - remote-endpoint + + required: + - endpoint + +required: + - compatible + - reg + - clocks + - assigned-clocks + - assigned-clock-rates + - dvdd-supply + - dovdd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sun8i-a83t-ccu.h> + #include <dt-bindings/gpio/gpio.h> + + i2c2 { + #address-cells = <1>; + #size-cells = <0>; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + bus-type = <4>; /* MIPI CSI-2 D-PHY */ + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; + }; + +...
Signature · 1 line
2.28.0
Re: [PATCH v2 1/3] dt-bindings: media: i2c: Add OV8865 bindings documentation
Quoted 11 lines · Paul Kocialkowski
This introduces YAML bindings documentation for the OV8865 image sensor.
Co-developed-by Kévin L'hôpital <[email protected]>Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- .../bindings/media/i2c/ovti,ov8865.yaml | 120 ++++++++++++++++++ 1 file changed, 120 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml
Sakari Ailus
maintainerRe: [PATCH v2 1/3] dt-bindings: media: i2c: Add OV8865 bindings documentation
In reply to Paul KocialkowskiHi Paul,
Quoted 71 lines · Paul Kocialkowski
This introduces YAML bindings documentation for the OV8865 image sensor.
Co-developed-by Kévin L'hôpital <[email protected]>Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- .../bindings/media/i2c/ovti,ov8865.yaml | 120 ++++++++++++++++++ 1 file changed, 120 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yamlDocumentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml new file +54
-0@@ -0,0 +1,120 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov8865.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV8865 Image Sensor Device Tree Bindings + +maintainers: + - Paul Kocialkowski <[email protected]> + +properties: + compatible: + const: ovti,ov8865 + + reg: + maxItems: 1 + + clocks: + items: + - description: EXTCLK Clock + + assigned-clocks: + maxItems: 1 + + assigned-clock-rates: + maxItems: 1 + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply (internal AVDD is used if missing) + + dovdd-supply: + description: I/O Domain Power Supply + + powerdown-gpios: + maxItems: 1 + description: Power Down Pin GPIO Control (active low) + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + type: object + description: MIPI CSI-2 transmitter port + + properties: + endpoint: + type: object + + properties:
Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml line 64
Quoted 10 lines
Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml new file +10
-0+ remote-endpoint: true + + data-lanes: + minItems: 1 + maxItems: 4 + + required: + - bus-type + - data-lanes + - remote-endpoint
link-frequencies seems to be still missing here (same with the example).
Signature · 1 line
Sakari Ailus
Re: [PATCH v2 1/3] dt-bindings: media: i2c: Add OV8865 bindings documentation
Hi Sakari,
Quoted 78 lines · Sakari Ailus
Hi Paul,
Quoted 75 lines · Paul Kocialkowski
This introduces YAML bindings documentation for the OV8865 image sensor.
Co-developed-by Kévin L'hôpital <[email protected]>Signed-off-by Kévin L'hôpital <[email protected]>Signed-off-by Paul Kocialkowski <[email protected]>--- .../bindings/media/i2c/ovti,ov8865.yaml | 120 ++++++++++++++++++ 1 file changed, 120 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yamlDocumentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml new file +58
-0@@ -0,0 +1,120 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov8865.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV8865 Image Sensor Device Tree Bindings + +maintainers: + - Paul Kocialkowski <[email protected]> + +properties: + compatible: + const: ovti,ov8865 + + reg: + maxItems: 1 + + clocks: + items: + - description: EXTCLK Clock + + assigned-clocks: + maxItems: 1 + + assigned-clock-rates: + maxItems: 1 + + dvdd-supply: + description: Digital Domain Power Supply + + avdd-supply: + description: Analog Domain Power Supply (internal AVDD is used if missing) + + dovdd-supply: + description: I/O Domain Power Supply + + powerdown-gpios: + maxItems: 1 + description: Power Down Pin GPIO Control (active low) + + reset-gpios: + maxItems: 1 + description: Reset Pin GPIO Control (active low) + + port: + type: object + description: MIPI CSI-2 transmitter port + + properties: + endpoint: + type: object + + properties: + remote-endpoint: true + + data-lanes: + minItems: 1
Quoted 8 lines
Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml line 64
Quoted 6 lines
Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml new file +6
-0+ maxItems: 4 + + required: + - bus-type + - data-lanes + - remote-endpointlink-frequencies seems to be still missing here (same with the example).
Oh my bad, you're right.
Note that I found an issue in this series (as well as the ov5648 one) so I will be reposting them anyways (likely later today).
Cheers,
Paul
Signature · 3 lines
Paul Kocialkowski, Bootlin Embedded Linux and kernel engineering https://bootlin.com
PATCH v2 2/3 media: i2c: Add support for the OV8865 image sensor
In reply to Paul KocialkowskiThe OV8865 is a 8 Mpx CMOS image sensor producing 3264x2448 at 30 fps. Other modes (including some with sub-sampling) are available too. It outputs 10-bit bayer CFA data through a MIPI CSI-2 interface with up to 4 lanes supported.
Some register initialisation sequences are still needed for this driver, as they cover registers for which no documentation is available.
This work is based on the first version of the driver submitted by Kévin L'hôpital, which was adapted to mainline from the Allwinner BSP. This version is a rewrite of the first version that matches the structure of the OV5648 driver, with explicit PLL configuration, all the necessary mode-specific fields, associatied registers and reduced static sequences.
It was tested with the Banana Pi Camera Board v3 and the Banana Pi M3.
--- drivers/media/i2c/Kconfig | 13 + drivers/media/i2c/Makefile | 1 + drivers/media/i2c/ov8865.c | 3043 ++++++++++++++++++++++++++++++++++++ 3 files changed, 3057 insertions(+) create mode 100644 drivers/media/i2c/ov8865.c
drivers/media/i2c/Kconfig +13 -0
@@ -1047,6 +1047,19 @@ config VIDEO_OV8856 To compile this driver as a module, choose M here: the module will be called ov8856. +config VIDEO_OV8865 + tristate "OmniVision OV8865 sensor support" + depends on I2C && VIDEO_V4L2 + select MEDIA_CONTROLLER + select VIDEO_V4L2_SUBDEV_API + select V4L2_FWNODE + help + This is a Video4Linux2 sensor driver for OmniVision + OV8865 camera sensor. + + To compile this driver as a module, choose M here: the + module will be called ov8865. + config VIDEO_OV9640 tristate "OmniVision OV9640 sensor support" depends on I2C && VIDEO_V4L2
drivers/media/i2c/Makefile +1 -0
@@ -82,6 +82,7 @@ obj-$(CONFIG_VIDEO_OV7670) += ov7670.o obj-$(CONFIG_VIDEO_OV772X) += ov772x.o obj-$(CONFIG_VIDEO_OV7740) += ov7740.o obj-$(CONFIG_VIDEO_OV8856) += ov8856.o +obj-$(CONFIG_VIDEO_OV8865) += ov8865.o obj-$(CONFIG_VIDEO_OV9640) += ov9640.o obj-$(CONFIG_VIDEO_OV9650) += ov9650.o obj-$(CONFIG_VIDEO_OV13858) += ov13858.o
drivers/media/i2c/ov8865.c new file +3043 -0
2,974 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.28.0
Part of the diff is not shown here. View the raw message.
PATCH v2 3/3 ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
In reply to Paul KocialkowskiFrom: Kévin L'hôpital <[email protected]>
The Bananapi M3 supports a camera module which includes an OV8865 sensor connected via the parallel CSI interface and an OV8865 sensor connected via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low) reset signal, but each sensor has it own shutdown line.
--- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 99 ++++++++++++++++++++ 1 file changed, 99 insertions(+)
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +99 -0
@@ -85,6 +85,30 @@ green { }; }; + reg_ov8865_avdd: ov8865-avdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dovdd: ov8865-dovdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dovdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + vin-supply = <®_dldo4>; + }; + + reg_ov8865_dvdd: ov8865-dvdd { + compatible = "regulator-fixed"; + regulator-name = "ov8865-dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <®_eldo1>; + }; + reg_usb1_vbus: reg-usb1-vbus { compatible = "regulator-fixed"; regulator-name = "usb1-vbus";
@@ -115,6 +139,17 @@ &cpu100 { cpu-supply = <®_dcdc3>; }; +&csi { + status = "okay"; +}; + +&csi_in { + csi_in_mipi_csi2: endpoint { + bus-type = <4>; /* CSI2_DPHY */ + remote-endpoint = <&mipi_csi2_out_csi>; + }; +}; + &de { status = "okay"; };
@@ -147,6 +182,37 @@ hdmi_out_con: endpoint { }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pe_pins>; + status = "okay"; + + ov8865: camera@36 { + compatible = "ovti,ov8865"; + reg = <0x36>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + assigned-clocks = <&ccu CLK_CSI_MCLK>; + assigned-clock-rates = <24000000>; + avdd-supply = <®_ov8865_avdd>; + dovdd-supply = <®_ov8865_dovdd>; + dvdd-supply = <®_ov8865_dvdd>; + powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */ + reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */ + + port { + ov8865_out_mipi_csi2: endpoint { + bus-type = <4>; /* MIPI CSI-2 D-PHY */ + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + + remote-endpoint = <&mipi_csi2_in_ov8865>; + }; + }; + }; +}; + &mdio { rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22";
@@ -154,6 +220,26 @@ rgmii_phy: ethernet-phy@1 { }; }; +&mipi_csi2 { + status = "okay"; +}; + +&mipi_csi2_in { + mipi_csi2_in_ov8865: endpoint { + bus-type = <4>; /* MIPI CSI-2 D-PHY */ + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + + remote-endpoint = <&ov8865_out_mipi_csi2>; + }; +}; + +&mipi_csi2_out { + mipi_csi2_out_csi: endpoint { + remote-endpoint = <&csi_in_mipi_csi2>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>;
@@ -327,11 +413,24 @@ ®_dldo3 { regulator-name = "vcc-pd"; }; +®_dldo4 { + regulator-always-on; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + ®_drivevbus { regulator-name = "usb0-vbus"; status = "okay"; }; +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dvdd-csi-r"; +}; + ®_fldo1 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>;
Signature · 1 line
2.28.0