pull-request: can 2020-11-30
Subsystems (5)
Marc Kleine-Budde
maintainerHello Jakub, hello David,
here's a pull request of 5 patches for net/master.
The first patch is by me an target the tcan4x5x bindings for the m_can driver. It fixes the error path in the tcan4x5x_can_probe() function.
The next two patches are by Jeroen Hofstee and makes the lost of arbitration error counters of sja1000 and the sun4i drivers consistent with the other drivers.
Zhang Qilong contributes two patch that clean up the error path in the c_can and kvaser_pciefd drivers.
regards,
Marc
---
The following changes since commit 4d521943f76bd0d1e68ea5e02df7aadd30b2838a:
dt-bindings: net: correct interrupt flags in examples (2020-11-28 14:47:56 -0800)
are available in the Git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can.git tags/linux-can-fixes-for-5.10-20201130
for you to fetch changes up to 13a84cf37a4cf1155a41684236c2314eb40cd65c:
can: kvaser_pciefd: kvaser_pciefd_open(): fix error handling (2020-11-30 12:43:55 +0100)
----------------------------------------------------------------
linux-can-fixes-for-5.10-20201130
----------------------------------------------------------------
Jeroen Hofstee (2):
can: sja1000: sja1000_err(): don't count arbitration lose as an error
can: sun4i_can: sun4i_can_err(): don't count arbitration lose as an error
Marc Kleine-Budde (1):
can: m_can: tcan4x5x_can_probe(): fix error path: remove erroneous clk_disable_unprepare()
Zhang Qilong (2):
can: c_can: c_can_power_up(): fix error handling
can: kvaser_pciefd: kvaser_pciefd_open(): fix error handling
drivers/net/can/c_can/c_can.c | 18 ++++++++++++++---- drivers/net/can/kvaser_pciefd.c | 4 +++- drivers/net/can/m_can/tcan4x5x.c | 11 +++-------- drivers/net/can/sja1000/sja1000.c | 1 - drivers/net/can/sun4i_can.c | 1 - 5 files changed, 20 insertions(+), 15 deletions(-)
Marc Kleine-Budde
maintainerPATCH 1/5 can: m_can: tcan4x5x_can_probe(): fix error path: remove erroneous clk_disable_unprepare()
The clocks mcan_class->cclk and mcan_class->hclk are not prepared by any call during tcan4x5x_can_probe(), so remove erroneous clk_disable_unprepare() on them.
--- drivers/net/can/m_can/tcan4x5x.c | 11 +++-------- 1 file changed, 3 insertions(+), 8 deletions(-)
drivers/net/can/m_can/tcan4x5x.c +3 -8
@@ -489,18 +489,18 @@ static int tcan4x5x_can_probe(struct spi_device *spi) spi->bits_per_word =32 ; ret =spi_setup (spi);if (ret) - goto out_clk; + goto out_m_can_class_free_dev; priv->regmap =devm_regmap_init (&spi->dev, &tcan4x5x_bus, &spi->dev, &tcan4x5x_regmap);if (IS_ERR (priv->regmap)) { ret =PTR_ERR (priv->regmap); - goto out_clk; + goto out_m_can_class_free_dev; } ret =tcan4x5x_power_enable (priv->power,1 );if (ret) - goto out_clk; + goto out_m_can_class_free_dev; ret =tcan4x5x_parse_config (mcan_class);if (ret)
@@ -519,11 +519,6 @@ static int tcan4x5x_can_probe(struct spi_device *spi) out_power:tcan4x5x_power_enable (priv->power,0 ); -out_clk: -if (!IS_ERR (mcan_class->cclk)) { -clk_disable_unprepare (mcan_class->cclk); -clk_disable_unprepare (mcan_class->hclk); - } out_m_can_class_free_dev:m_can_class_free_dev (mcan_class->net);dev_err (&spi->dev,"Probe failed, err=%d\n" , ret);
base-commit: 4d521943f76bd0d1e68ea5e02df7aadd30b2838a
Signature · 1 line
2.29.2
Marc Kleine-Budde
maintainerPATCH 2/5 can: sja1000: sja1000_err(): don't count arbitration lose as an error
In reply to Marc Kleine-BuddeFrom: Jeroen Hofstee <[email protected]>
Losing arbitration is normal in a CAN-bus network, it means that a higher priority frame is being send and the pending message will be retried later. Hence most driver only increment arbitration_lost, but the sja1000 driver also incremeants tx_error, causing errors to be reported on a normal functioning CAN-bus. So stop counting them as errors.
--- drivers/net/can/sja1000/sja1000.c | 1 - 1 file changed, 1 deletion(-)
drivers/net/can/sja1000/sja1000.c +0 -1
@@ -474,7 +474,6 @@ static int sja1000_err(struct net_device *dev, uint8_t isrc, uint8_t status)netdev_dbg (dev,"arbitration lost interrupt\n" ); alc = priv->read_reg (priv,SJA1000_ALC ); priv->can.can_stats.arbitration_lost++; - stats->tx_errors++; cf->can_id |=CAN_ERR_LOSTARB ; cf->data[0 ] = alc &0x1f ; }
Signature · 1 line
2.29.2
Marc Kleine-Budde
maintainerPATCH 3/5 can: sun4i_can: sun4i_can_err(): don't count arbitration lose as an error
In reply to Marc Kleine-BuddeFrom: Jeroen Hofstee <[email protected]>
Losing arbitration is normal in a CAN-bus network, it means that a higher priority frame is being send and the pending message will be retried later. Hence most driver only increment arbitration_lost, but the sun4i driver also incremeants tx_error, causing errors to be reported on a normal functioning CAN-bus. So stop counting them as errors.
--- drivers/net/can/sun4i_can.c | 1 - 1 file changed, 1 deletion(-)
drivers/net/can/sun4i_can.c +0 -1
@@ -604,7 +604,6 @@ static int sun4i_can_err(struct net_device *dev, u8 isrc, u8 status)netdev_dbg (dev,"arbitration lost interrupt\n" ); alc =readl (priv->base +SUN4I_REG_STA_ADDR ); priv->can.can_stats.arbitration_lost++; - stats->tx_errors++;if (likely (skb)) { cf->can_id |=CAN_ERR_LOSTARB ; cf->data[0 ] = (alc >>8 ) &0x1f ;
Signature · 1 line
2.29.2
Marc Kleine-Budde
maintainerPATCH 4/5 can: c_can: c_can_power_up(): fix error handling
In reply to Marc Kleine-BuddeFrom: Zhang Qilong <[email protected]>
In the error handling in c_can_power_up(), there are two bugs:
1) c_can_pm_runtime_get_sync() will increase usage counter if device is not empty. Forgetting to call c_can_pm_runtime_put_sync() will result in a reference leak here.
2) c_can_reset_ram() operation will set start bit when enable is true. We should clear it in the error handling.
We fix it by adding c_can_pm_runtime_put_sync() for 1), and c_can_reset_ram(enable is false) for 2) in the error handling.
--- drivers/net/can/c_can/c_can.c | 18 ++++++++++++++---- 1 file changed, 14 insertions(+), 4 deletions(-)
drivers/net/can/c_can/c_can.c +14 -4
@@ -1295,12 +1295,22 @@ int c_can_power_up(struct net_device *dev) time_after(time_out, jiffies))cpu_relax (); -if (time_after (jiffies, time_out)) -return -ETIMEDOUT ; +if (time_after (jiffies, time_out)) { + ret = -ETIMEDOUT ; + goto err_out; + } ret =c_can_start (dev); -if (!ret) -c_can_irq_control (priv, true); +if (ret) + goto err_out; + +c_can_irq_control (priv, true); + +return 0 ; + +err_out: +c_can_reset_ram (priv, false); +c_can_pm_runtime_put_sync (priv);return ret; }
Signature · 1 line
2.29.2
Marc Kleine-Budde
maintainerPATCH 5/5 can: kvaser_pciefd: kvaser_pciefd_open(): fix error handling
In reply to Marc Kleine-BuddeFrom: Zhang Qilong <[email protected]>
If kvaser_pciefd_bus_on() failed, we should call close_candev() to avoid reference leak.
--- drivers/net/can/kvaser_pciefd.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/net/can/kvaser_pciefd.c +3 -1
@@ -692,8 +692,10 @@ static int kvaser_pciefd_open(struct net_device *netdev)return err; err =kvaser_pciefd_bus_on (can); -if (err) +if (err) { +close_candev (netdev);return err; + }return 0 ; }
Signature · 1 line
2.29.2
Jakub Kicinski
maintainerQuoted 7 lines · On Mon, 30 Nov 2020 13:53:02 +0100 Marc Kleine-Budde wrote:
Hello Jakub, hello David,
here's a pull request of 5 patches for net/master.
The first patch is by me an target the tcan4x5x bindings for the
m_candriver. It fixes the error path in thetcan4x5x_can_probe()function.
Quoted 6 lines
The next two patches are by Jeroen Hofstee and makes the lost of arbitration error counters of sja1000 and the sun4i drivers consistent with the other drivers.
Zhang Qilong contributes two patch that clean up the error path in the
c_canandkvaser_pciefddrivers.
Pulled, thanks!