Skip to contentSkip to conversation

dt-bindings: edac: aspeed-sdram-edac: Add ast2400/ast2600 support

PATCH In review Troy Lee 4 participants 6 messages Dec 7, 2020

Subsystems (4)
lore
Share & tools
lore

Troy Lee

author
#0 lore raw

PATCH v4 1/3 dt-bindings: edac: aspeed-sdram-edac: Add ast2400/ast2600 support

Adding Aspeed AST2400 and AST2600 binding for edac driver.

---
 .../devicetree/bindings/edac/aspeed-sdram-edac.txt       | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt +6 -3
index 6a0f3d90d682..8ca9e0a049d8 100644
@@ -1,6 +1,6 @@
-Aspeed AST2500 SoC EDAC node
+Aspeed BMC SoC EDAC node
 
-The Aspeed AST2500 SoC supports DDR3 and DDR4 memory with and without ECC (error
+The Aspeed BMC SoC supports DDR3 and DDR4 memory with and without ECC (error
 correction check).
 
 The memory controller supports SECDED (single bit error correction, double bit
@@ -11,7 +11,10 @@ Note, the bootloader must configure ECC mode in the memory controller.
 
 
 Required properties:
-- compatible: should be "aspeed,ast2500-sdram-edac"
+- compatible: should be one of
+	- "aspeed,ast2400-sdram-edac"
+	- "aspeed,ast2500-sdram-edac"
+	- "aspeed,ast2600-sdram-edac"
 - reg:        sdram controller register set should be <0x1e6e0000 0x174>
 - interrupts: should be AVIC interrupt #0
 
Signature · 1 line
2.17.1
author
#1 lore raw

PATCH v4 2/3 ARM: dts: aspeed: Add AST2600 edac into common devicetree

Adding Aspeed AST2600 edac node into common devicetree.

---
 arch/arm/boot/dts/aspeed-g6.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm/boot/dts/aspeed-g6.dtsi +6 -0
index b58220a49cbd..74367ee96f20 100644
@@ -69,6 +69,12 @@
 		always-on;
 	};
 
+	edac: sdram at 1e6e0000 {
+		compatible = "aspeed,ast2600-sdram-edac", "syscon";
+		reg = <0x1e6e0000 0x174>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
 	ahb {
 		compatible = "simple-bus";
 		#address-cells = <1>;
Signature · 1 line
2.17.1
author
#2 lore raw

PATCH v4 3/3 edac: Supporting AST2400 and AST2600 edac driver

In reply to Troy Lee

Adding AST2400 and AST2600 edac driver support.

---
 drivers/edac/Kconfig       | 6 +++---
 drivers/edac/aspeed_edac.c | 7 +++++--
 2 files changed, 8 insertions(+), 5 deletions(-)
drivers/edac/Kconfig +3 -3
index 7a47680d6f07..c410331e8ee8 100644
@@ -515,10 +515,10 @@ config EDAC_QCOM
 	  health, you should probably say 'Y' here.
 
 config EDAC_ASPEED
-	tristate "Aspeed AST 2500 SoC"
-	depends on MACH_ASPEED_G5
+	tristate "Aspeed AST BMC SoC"
+	depends on ARCH_ASPEED
 	help
-	  Support for error detection and correction on the Aspeed AST 2500 SoC.
+	  Support for error detection and correction on the Aspeed AST BMC SoC.
 
 	  First, ECC must be configured in the bootloader. Then, this driver
 	  will expose error counters via the EDAC kernel framework.
drivers/edac/aspeed_edac.c +5 -2
index fde809efc520..a46da56d6d54 100644
@@ -239,7 +239,7 @@ static int init_csrows(struct mem_ctl_info *mci)
 	int rc;
 
 	/* retrieve info about physical memory from device tree */
-	np = of_find_node_by_path("/memory");
+	np = of_find_node_by_name(NULL, "memory");
 	if (!np) {
 		dev_err(mci->pdev, "dt: missing /memory node\n");
 		return -ENODEV;
@@ -375,10 +375,13 @@ static int aspeed_remove(struct platform_device *pdev)
 
 
 static const struct of_device_id aspeed_of_match[] = {
+	{ .compatible = "aspeed,ast2400-sdram-edac" },
 	{ .compatible = "aspeed,ast2500-sdram-edac" },
+	{ .compatible = "aspeed,ast2600-sdram-edac" },
 	{},
 };
 
+MODULE_DEVICE_TABLE(of, aspeed_of_match);
 
 static struct platform_driver aspeed_driver = {
 	.driver		= {
@@ -392,5 +395,5 @@ module_platform_driver(aspeed_driver);
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Stefan Schaeckeler <[email protected]>");
-MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
+MODULE_DESCRIPTION("Aspeed BMC SoC EDAC driver");
 MODULE_VERSION("1.0");
Signature · 1 line
2.17.1
maintainer Reviewed-by on v4 3/3
#3 lore raw

Re: [PATCH v4 3/3] edac: Supporting AST2400 and AST2600 edac driver

Quoted 3 lines

Adding AST2400 and AST2600 edac driver support.

Quoted 1 line

---

     drivers/edac/Kconfig       | 6 +++---
Quoted 57 lines
 drivers/edac/aspeed_edac.c | 7 +++++--
 2 files changed, 8 insertions(+), 5 deletions(-)
drivers/edac/Kconfig +3 -3
index 7a47680d6f07..c410331e8ee8 100644
@@ -515,10 +515,10 @@ config EDAC_QCOM
 	  health, you should probably say 'Y' here.
 
 config EDAC_ASPEED
-	tristate "Aspeed AST 2500 SoC"
-	depends on MACH_ASPEED_G5
+	tristate "Aspeed AST BMC SoC"
+	depends on ARCH_ASPEED
 	help
-	  Support for error detection and correction on the Aspeed AST 2500 SoC.
+	  Support for error detection and correction on the Aspeed AST BMC SoC.
 
 	  First, ECC must be configured in the bootloader. Then, this driver
 	  will expose error counters via the EDAC kernel framework.
drivers/edac/aspeed_edac.c +5 -2
index fde809efc520..a46da56d6d54 100644
@@ -239,7 +239,7 @@ static int init_csrows(struct mem_ctl_info *mci)
 	int rc;
 
 	/* retrieve info about physical memory from device tree */
-	np = of_find_node_by_path("/memory");
+	np = of_find_node_by_name(NULL, "memory");
 	if (!np) {
 		dev_err(mci->pdev, "dt: missing /memory node\n");
 		return -ENODEV;
@@ -375,10 +375,13 @@ static int aspeed_remove(struct platform_device *pdev)
 
 
 static const struct of_device_id aspeed_of_match[] = {
+	{ .compatible = "aspeed,ast2400-sdram-edac" },
 	{ .compatible = "aspeed,ast2500-sdram-edac" },
+	{ .compatible = "aspeed,ast2600-sdram-edac" },
 	{},
 };
 
+MODULE_DEVICE_TABLE(of, aspeed_of_match);
 
 static struct platform_driver aspeed_driver = {
 	.driver		= {
@@ -392,5 +395,5 @@ module_platform_driver(aspeed_driver);
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Stefan Schaeckeler <[email protected]>");
-MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
+MODULE_DESCRIPTION("Aspeed BMC SoC EDAC driver");
 MODULE_VERSION("1.0");
Signature · 1 line
2.17.1