drm/amd/pm: update the smu v11.5 smc header for vangogh
Subsystems (3)
PATCH 1/3 drm/amd/pm: update the smu v11.5 smc header for vangogh
Add new PMFW message to notify RLC engine status.
--- drivers/gpu/drm/amd/pm/inc/smu_types.h | 2 +- drivers/gpu/drm/amd/pm/inc/smu_v11_5_ppsmc.h | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/amd/pm/inc/smu_types.h +1 -1
@@ -178,7 +178,7 @@__SMU_DUMMY_MAP (SET_DRIVER_DUMMY_TABLE_DRAM_ADDR_LOW ), \__SMU_DUMMY_MAP (GET_UMC_FW_WA ), \__SMU_DUMMY_MAP (Mode1Reset), \ -__SMU_DUMMY_MAP (Spare), \ +__SMU_DUMMY_MAP (RlcPowerNotify), \__SMU_DUMMY_MAP (SetHardMinIspiclkByFreq), \__SMU_DUMMY_MAP (SetHardMinIspxclkByFreq), \ __SMU_DUMMY_MAP(SetSoftMinSocclkByFreq), \
drivers/gpu/drm/amd/pm/inc/smu_v11_5_ppsmc.h +1 -1
@@ -41,7 +41,7 @@#define PPSMC_MSG_PowerUpIspByTile 0x7#define PPSMC_MSG_PowerDownVcn 0x8 // VCN is power gated by default#define PPSMC_MSG_PowerUpVcn 0x9 -#define PPSMC_MSG_spare 0xA +#define PPSMC_MSG_RlcPowerNotify 0xA#define PPSMC_MSG_SetHardMinVcn 0xB // For wireless display#define PPSMC_MSG_SetSoftMinGfxclk 0xC //Sets SoftMin for GFXCLK. Arg is in MHz#define PPSMC_MSG_ActiveProcessNotify 0xD
Signature · 6 lines
2.17.1 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 2/3 drm/amd/pm: add interface to notify RLC status for vangogh
Add this interface to notify PMFW the status (Normal/Off) of RLC engine.
Before notify RLC status normal, need check its current status first. Send the message only when current status is still off.
--- drivers/gpu/drm/amd/pm/inc/amdgpu_smu.h | 1 + .../gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c | 24 ++++++++++++++++++- .../gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.h | 4 ++++ drivers/gpu/drm/amd/pm/swsmu/smu_cmn.c | 13 ++++++++++ drivers/gpu/drm/amd/pm/swsmu/smu_cmn.h | 2 ++ drivers/gpu/drm/amd/pm/swsmu/smu_internal.h | 1 + 6 files changed, 44 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/pm/inc/amdgpu_smu.h +1 -0
@@ -583,6 +583,7 @@ struct pptable_funcs {int (*gpo_control)(struct smu_context *smu,bool enablement);int (*gfx_state_change_set)(struct smu_context *smu,uint32_t state);int (*set_fine_grain_gfx_freq_parameters)(struct smu_context *smu); +int (*notify_rlc_status)(struct smu_context *smu,uint32_t status); }; typedef enum {
drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c +23 -1
@@ -64,7 +64,7 @@ static struct cmn2asic_msg_mapping vangogh_message_map[SMU_MSG_MAX_COUNT] = {MSG_MAP (PowerUpIspByTile, PPSMC_MSG_PowerUpIspByTile,0 ),MSG_MAP (PowerDownVcn, PPSMC_MSG_PowerDownVcn,0 ),MSG_MAP (PowerUpVcn, PPSMC_MSG_PowerUpVcn,0 ), -MSG_MAP (Spare, PPSMC_MSG_spare,0 ), +MSG_MAP (RlcPowerNotify, PPSMC_MSG_RlcPowerNotify,0 ),MSG_MAP (SetHardMinVcn, PPSMC_MSG_SetHardMinVcn,0 ),MSG_MAP (SetSoftMinGfxclk, PPSMC_MSG_SetSoftMinGfxclk,0 ), MSG_MAP(ActiveProcessNotify, PPSMC_MSG_ActiveProcessNotify, 0),
@@ -722,6 +722,27 @@ static int vangogh_set_fine_grain_gfx_freq_parameters(struct smu_context *smu)return 0 ; } +static int vangogh_notify_rlc_status (struct smu_context *smu,uint32_t status) +{ +int ret =0 ; + +switch (status) + { +case RLC_STATUS_OFF : + ret =smu_cmn_send_smc_msg_with_param (smu, SMU_MSG_RlcPowerNotify, status,NULL ); +break ; +case RLC_STATUS_NORMAL : +if (smu_cmn_get_rlc_status (smu) ==0 ) + ret =smu_cmn_send_smc_msg_with_param (smu, SMU_MSG_RlcPowerNotify, status,NULL ); +break ; +default : +dev_err (smu->adev->dev,"Unknown rlc status\n" ); +return -EINVAL ; + } + +return ret; +} +static const struct pptable_funcs vangogh_ppt_funcs = { .check_fw_status = smu_v11_0_check_fw_status,
@@ -750,6 +771,7 @@ static const struct pptable_funcs vangogh_ppt_funcs = { .print_clk_levels = vangogh_print_fine_grain_clk, .set_default_dpm_table = vangogh_set_default_dpm_tables, .set_fine_grain_gfx_freq_parameters = vangogh_set_fine_grain_gfx_freq_parameters, + .notify_rlc_status = vangogh_notify_rlc_status, };void vangogh_set_ppt_funcs (struct smu_context *smu)
drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.h +4 -0
@@ -32,4 +32,8 @@ extern void vangogh_set_ppt_funcs(struct smu_context *smu);#define VANGOGH_UMD_PSTATE_SOCCLK 678#define VANGOGH_UMD_PSTATE_FCLK 800 +/* RLC Power Status */ +#define RLC_STATUS_OFF 0 +#define RLC_STATUS_NORMAL 1 +#endif
drivers/gpu/drm/amd/pm/swsmu/smu_cmn.c +13 -0
@@ -42,6 +42,9 @@* They share the same definitions and values. That makes common * APIs for SMC messages issuing for all ASICs possible. */ +#define mmMP1_SMN_C2PMSG_63 0x027f +#define mmMP1_SMN_C2PMSG_63_BASE_IDX 0 +#define mmMP1_SMN_C2PMSG_66 0x0282#define mmMP1_SMN_C2PMSG_66_BASE_IDX 0
@@ -731,3 +734,13 @@ int smu_cmn_get_metrics_table(struct smu_context *smu,return ret; } + +int smu_cmn_get_rlc_status (struct smu_context *smu) +{ +struct amdgpu_device *adev = smu->adev; +uint32_t val; + + val =RREG32_SOC15_NO_KIQ (MP1 ,0 , mmMP1_SMN_C2PMSG_63); + +return val; +}
drivers/gpu/drm/amd/pm/swsmu/smu_cmn.h +2 -0
@@ -95,5 +95,7 @@ int smu_cmn_get_metrics_table(struct smu_context *smu,void *metrics_table, bool bypass_cache); +int smu_cmn_get_rlc_status (struct smu_context *smu); +#endif #endif
drivers/gpu/drm/amd/pm/swsmu/smu_internal.h +1 -0
@@ -91,6 +91,7 @@#define smu_post_init (smu) smu_ppt_funcs(post_init, 0, smu)#define smu_gpo_control (smu, enablement) smu_ppt_funcs(gpo_control, 0, smu, enablement)#define smu_set_fine_grain_gfx_freq_parameters (smu) smu_ppt_funcs(set_fine_grain_gfx_freq_parameters, 0, smu) +#define smu_notify_rlc_status (smu, status) smu_ppt_funcs(notify_rlc_status, 0, smu, status)#endif #endif
Signature · 6 lines
2.17.1 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
Re: [PATCH 2/3] drm/amd/pm: add interface to notify RLC status for vangogh
[AMD Official Use Only - Internal Distribution Only]
________________________________
From: amd-gfx <[email protected]> on behalf of Xiaomeng Hou <[email protected]>
Sent: Tuesday, December 8, 2020 7:19 PM
To: [email protected] <[email protected]>
Cc: Deucher, Alexander <[email protected]>; Huang, Ray <[email protected]>; Hou, Xiaomeng (Matthew) <[email protected]>; Quan, Evan <[email protected]>
Subject: [PATCH 2/3] drm/amd/pm: add interface to notify RLC status for vangogh
Add this interface to notify PMFW the status (Normal/Off) of RLC engine.
Before notify RLC status normal, need check its current status first. Send the message only when current status is still off.
--- drivers/gpu/drm/amd/pm/inc/amdgpu_smu.h | 1 + .../gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c | 24 ++++++++++++++++++- .../gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.h | 4 ++++ drivers/gpu/drm/amd/pm/swsmu/smu_cmn.c | 13 ++++++++++ drivers/gpu/drm/amd/pm/swsmu/smu_cmn.h | 2 ++ drivers/gpu/drm/amd/pm/swsmu/smu_internal.h | 1 + 6 files changed, 44 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/pm/inc/amdgpu_smu.h +1 -0
@@ -583,6 +583,7 @@ struct pptable_funcs {int (*gpo_control)(struct smu_context *smu,bool enablement);int (*gfx_state_change_set)(struct smu_context *smu,uint32_t state);int (*set_fine_grain_gfx_freq_parameters)(struct smu_context *smu); +int (*notify_rlc_status)(struct smu_context *smu,uint32_t status); }; typedef enum {
drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c +23 -1
@@ -64,7 +64,7 @@ static struct cmn2asic_msg_mapping vangogh_message_map[SMU_MSG_MAX_COUNT] = {MSG_MAP (PowerUpIspByTile, PPSMC_MSG_PowerUpIspByTile,0 ),MSG_MAP (PowerDownVcn, PPSMC_MSG_PowerDownVcn,0 ),MSG_MAP (PowerUpVcn, PPSMC_MSG_PowerUpVcn,0 ), -MSG_MAP (Spare, PPSMC_MSG_spare,0 ), +MSG_MAP (RlcPowerNotify, PPSMC_MSG_RlcPowerNotify,0 ),MSG_MAP (SetHardMinVcn, PPSMC_MSG_SetHardMinVcn,0 ),MSG_MAP (SetSoftMinGfxclk, PPSMC_MSG_SetSoftMinGfxclk,0 ), MSG_MAP(ActiveProcessNotify, PPSMC_MSG_ActiveProcessNotify, 0),
@@ -722,6 +722,27 @@ static int vangogh_set_fine_grain_gfx_freq_parameters(struct smu_context *smu)return 0 ; } +static int vangogh_notify_rlc_status (struct smu_context *smu,uint32_t status) +{ +int ret =0 ; + +switch (status) + { +case RLC_STATUS_OFF : + ret =smu_cmn_send_smc_msg_with_param (smu, SMU_MSG_RlcPowerNotify, status,NULL ); +break ; +case RLC_STATUS_NORMAL : +if (smu_cmn_get_rlc_status (smu) ==0 ) + ret =smu_cmn_send_smc_msg_with_param (smu, SMU_MSG_RlcPowerNotify, status,NULL ); +break ; +default : +dev_err (smu->adev->dev,"Unknown rlc status\n" ); +return -EINVAL ; + } + +return ret; +} +static const struct pptable_funcs vangogh_ppt_funcs = { .check_fw_status = smu_v11_0_check_fw_status,
@@ -750,6 +771,7 @@ static const struct pptable_funcs vangogh_ppt_funcs = { .print_clk_levels = vangogh_print_fine_grain_clk, .set_default_dpm_table = vangogh_set_default_dpm_tables, .set_fine_grain_gfx_freq_parameters = vangogh_set_fine_grain_gfx_freq_parameters, + .notify_rlc_status = vangogh_notify_rlc_status, };void vangogh_set_ppt_funcs (struct smu_context *smu)
drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.h +4 -0
@@ -32,4 +32,8 @@ extern void vangogh_set_ppt_funcs(struct smu_context *smu);#define VANGOGH_UMD_PSTATE_SOCCLK 678#define VANGOGH_UMD_PSTATE_FCLK 800 +/* RLC Power Status */ +#define RLC_STATUS_OFF 0 +#define RLC_STATUS_NORMAL 1 +#endif
drivers/gpu/drm/amd/pm/swsmu/smu_cmn.c +13 -0
@@ -42,6 +42,9 @@* They share the same definitions and values. That makes common * APIs for SMC messages issuing for all ASICs possible. */ +#define mmMP1_SMN_C2PMSG_63 0x027f +#define mmMP1_SMN_C2PMSG_63_BASE_IDX 0 +#define mmMP1_SMN_C2PMSG_66 0x0282#define mmMP1_SMN_C2PMSG_66_BASE_IDX 0
@@ -731,3 +734,13 @@ int smu_cmn_get_metrics_table(struct smu_context *smu,return ret; } + +int smu_cmn_get_rlc_status (struct smu_context *smu) +{ +struct amdgpu_device *adev = smu->adev; +uint32_t val; + + val =RREG32_SOC15_NO_KIQ (MP1 ,0 , mmMP1_SMN_C2PMSG_63); + +return val; +}
[kevin]:
these are not common code for whole smu driver, please move it to ppt.c file.
\ No newline at end of file
drivers/gpu/drm/amd/pm/swsmu/smu_cmn.h +2 -0
@@ -95,5 +95,7 @@ int smu_cmn_get_metrics_table(struct smu_context *smu,void *metrics_table, bool bypass_cache); +int smu_cmn_get_rlc_status (struct smu_context *smu); +#endif #endif
drivers/gpu/drm/amd/pm/swsmu/smu_internal.h +1 -0
@@ -91,6 +91,7 @@#define smu_post_init (smu) smu_ppt_funcs(post_init, 0, smu)#define smu_gpo_control (smu, enablement) smu_ppt_funcs(gpo_control, 0, smu, enablement)#define smu_set_fine_grain_gfx_freq_parameters (smu) smu_ppt_funcs(set_fine_grain_gfx_freq_parameters, 0, smu) +#define smu_notify_rlc_status (smu, status) smu_ppt_funcs(notify_rlc_status, 0, smu, status)#endif #endif
--
2.17.1
_______________________________________________
amd-gfx mailing list
[email protected]
https://nam11.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.freedesktop.org%2Fmailman%2Flistinfo%2Famd-gfx&data=04%7C01%7CKevin1.Wang%40amd.com%7Cf740746f29d14d4777e808d89b6b4971%7C3dd8961fe4884e608e11a82d994e183d%7C0%7C0%7C637430232414406734%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=VPGv9GuTb22ZkzKp98iG3ibpG7BSwKaw%2FBT%2F6DFDnSs%3D&reserved=0
_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
PATCH 3/3 drm/amdgpu/pm: inform PMFW rlc status before start/stop rlc for vangogh
In reply to Xiaomeng HouRLC is halted when system suspend/shutdown. However, due to DPM enabled, PMFM is unaware of RLC being halted and will continue sending messages, which would eventually caused ACPI related hang. So send message to inform PMFM the rlc status before start/stop rlc.
--- drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +16 -0
@@ -920,6 +920,14 @@ static int smu_smc_hw_setup(struct smu_context *smu)uint32_t pcie_gen =0 , pcie_width =0 ;int ret =0 ; +if (adev->in_suspend && smu->is_apu) { + ret =smu_notify_rlc_status (smu,1 ); +if (ret) { +dev_info (adev->dev,"Failed to notify rlc status!\n" ); +return ret; + } + } +if (adev->in_suspend &&smu_is_dpm_running (smu)) {dev_info (adev->dev,"dpm has been enabled\n" );/* this is needed specifically */
@@ -1213,6 +1221,14 @@ static int smu_disable_dpms(struct smu_context *smu)dev_err (adev->dev,"Failed to disable smu features.\n" ); } +if (smu->is_apu) { + ret =smu_notify_rlc_status (smu,0 ); +if (ret) { +dev_info (adev->dev,"Failed to notify rlc status!\n" ); +return ret; + } + } +if (adev->asic_type >=CHIP_NAVI10 && adev->gfx.rlc.funcs->stop) adev->gfx.rlc.funcs->stop (adev);
Signature · 6 lines
2.17.1 _______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
Re: [PATCH 3/3] drm/amdgpu/pm: inform PMFW rlc status before start/stop rlc for vangogh
[AMD Official Use Only - Internal Distribution Only]
________________________________
From: amd-gfx <[email protected]> on behalf of Xiaomeng Hou <[email protected]>
Sent: Tuesday, December 8, 2020 7:19 PM
To: [email protected] <[email protected]>
Cc: Deucher, Alexander <[email protected]>; Huang, Ray <[email protected]>; Hou, Xiaomeng (Matthew) <[email protected]>; Quan, Evan <[email protected]>
Subject: [PATCH 3/3] drm/amdgpu/pm: inform PMFW rlc status before start/stop rlc for vangogh
RLC is halted when system suspend/shutdown. However, due to DPM enabled, PMFM is unaware of RLC being halted and will continue sending messages, which would eventually caused ACPI related hang. So send message to inform PMFM the rlc status before start/stop rlc.
--- drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +2 -0
@@ -920,6 +920,14 @@ static int smu_smc_hw_setup(struct smu_context *smu)uint32_t pcie_gen =0 , pcie_width =0 ;int ret =0 ; +if (adev->in_suspend && smu->is_apu) { + ret =smu_notify_rlc_status (smu,1 );
[kevin]:
for 2nd parameter of '1', why not use the macro to replace it which is defined in previous patch ? and why not put these codes into smu_resume/suspend functions?
+ if (ret) {
+ dev_info(adev->dev, "Failed to notify rlc status!\n");
+ return ret;
+ }
+ }
+
if (adev->in_suspend && smu_is_dpm_running(smu)) {
dev_info(adev->dev, "dpm has been enabled\n");
/* this is needed specifically */
@@ -1213,6 +1221,14 @@ static int smu_disable_dpms(struct smu_context *smu)
dev_err(adev->dev, "Failed to disable smu features.\n");
}+ if (smu->is_apu) {
+ ret = smu_notify_rlc_status(smu, 0);
+ if (ret) {
+ dev_info(adev->dev, "Failed to notify rlc status!\n");
+ return ret;
+ }
+ }
+
if (adev->asic_type >= CHIP_NAVI10 &&
adev->gfx.rlc.funcs->stop)
adev->gfx.rlc.funcs->stop(adev);--
2.17.1
_______________________________________________
amd-gfx mailing list
[email protected]
https://nam11.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.freedesktop.org%2Fmailman%2Flistinfo%2Famd-gfx&data=04%7C01%7CKevin1.Wang%40amd.com%7Cb3afedc0e8a34992b17408d89b6b4f02%7C3dd8961fe4884e608e11a82d994e183d%7C0%7C0%7C637430232491676693%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=2gyWC0ytrVqLqNX2OappS8ALSyWkNa0xKYp96vMpxfk%3D&reserved=0
_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
Re: [PATCH 3/3] drm/amdgpu/pm: inform PMFW rlc status before start/stop rlc for vangogh
In reply to Xiaomeng HouQuoted 16 lines · Xiaomeng (Matthew)
RLC is halted when system suspend/shutdown. However, due to DPM enabled, PMFM is unaware of RLC being halted and will continue sending messages, which would eventually caused ACPI related hang. So send message to inform PMFM the rlc status before start/stop rlc.
Signed-off-by Xiaomeng Hou <[email protected]>Change-Id I7b1a04f6e249ac6753109079ecb3019c99161d9f--- drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +0
-0
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c static int smu_smc_hw_setup(struct smu_context *smu) · line 924
Quoted 5 lines
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +2
-0@@ -920,6 +920,14 @@ static int smu_smc_hw_setup(struct smu_context *smu)uint32_t pcie_gen =0 , pcie_width =0 ;int ret =0 ; +if (adev->in_suspend && smu->is_apu) { + ret =smu_notify_rlc_status (smu,1 );
You can create two new callbacks in ppt_funcs->inform_rlc(smu, on), and set on as bool type.
Then you can use below macros to implement this callback with RLC notify SMC message.
/* RLC Power Status */
#define RLC_STATUS_OFF 0
#define RLC_STATUS_NORMAL 1
Others look good for me.
Thanks,
Ray
Quoted 27 lines
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +14
-0+if (ret) { +dev_info (adev->dev,"Failed to notify rlc status!\n" ); +return ret; + } + } +if (adev->in_suspend &&smu_is_dpm_running (smu)) {dev_info (adev->dev,"dpm has been enabled\n" );/* this is needed specifically */ @@ -1213,6 +1221,14 @@ static int smu_disable_dpms(struct smu_context *smu)dev_err (adev->dev,"Failed to disable smu features.\n" ); } +if (smu->is_apu) { + ret =smu_notify_rlc_status (smu,0 ); +if (ret) { +dev_info (adev->dev,"Failed to notify rlc status!\n" ); +return ret; + } + } +if (adev->asic_type >=CHIP_NAVI10 && adev->gfx.rlc.funcs->stop) adev->gfx.rlc.funcs->stop (adev);Signature · 1 line
2.17.1
_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
RE: [PATCH 3/3] drm/amdgpu/pm: inform PMFW rlc status before start/stop rlc for vangogh
[AMD Public Use]
Quoted 1 line
You can create two new callbacks in
ppt_funcs->inform_rlc(smu, on), and set on as bool type
We can't keep adding ASIC specific workarounds as ppt_funcs. We should make use of the existing ones or have something generic to handle these quirks. System features control is one generic place in the logic which is used to control features. It's used in dGPU context only now, but it may be repurposed for FW notifications.
Thanks,
Lijo
-----Original Message-----
From: amd-gfx <[email protected]> On Behalf Of Huang Rui
Sent: Tuesday, December 8, 2020 6:39 PM
To: Hou, Xiaomeng (Matthew) <[email protected]>
Cc: Deucher, Alexander <[email protected]>; Quan, Evan <[email protected]>; [email protected]
Subject: Re: [PATCH 3/3] drm/amdgpu/pm: inform PMFW rlc status before start/stop rlc for vangogh
[CAUTION: External Email]
Quoted 17 lines · Xiaomeng (Matthew)
RLC is halted when system suspend/shutdown. However, due to DPM enabled, PMFM is unaware of RLC being halted and will continue sending messages, which would eventually caused ACPI related hang. So send message to inform PMFM the rlc status before start/stop rlc.
Signed-off-by Xiaomeng Hou <[email protected]>Change-Id I7b1a04f6e249ac6753109079ecb3019c99161d9f--- drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +0
-0
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c static int smu_smc_hw_setup(struct smu_context *smu) · line 924
Quoted 5 lines
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +2
-0@@ -920,6 +920,14 @@ static int smu_smc_hw_setup(struct smu_context *smu)uint32_t pcie_gen =0 , pcie_width =0 ;int ret =0 ; +if (adev->in_suspend && smu->is_apu) { + ret =smu_notify_rlc_status (smu,1 );
You can create two new callbacks in ppt_funcs->inform_rlc(smu, on), and set on as bool type.
Then you can use below macros to implement this callback with RLC notify SMC message.
/* RLC Power Status */
#define RLC_STATUS_OFF 0
#define RLC_STATUS_NORMAL 1
Others look good for me.
Thanks,
Ray
Quoted 25 lines
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +6
-0+if (ret) { +dev_info (adev->dev,"Failed to notify rlc status!\n" ); +return ret; + } + } +if (adev->in_suspend &&smu_is_dpm_running (smu)) {dev_info (adev->dev,"dpm has been enabled\n" ); /* this is needed specifically */ @@ -1213,6 +1221,14 @@static int
smu_disable_dpms(struct smu_context *smu)dev_err(adev->dev, "Failed to disable smu features.\n"); }drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +8
-1+if (smu->is_apu) { + ret =smu_notify_rlc_status (smu,0 ); +if (ret) { +dev_info (adev->dev,"Failed to notify rlc status!\n" ); +return ret; + } + } +if (adev->asic_type >=CHIP_NAVI10 && adev->gfx.rlc.funcs->stop) adev->gfx.rlc.funcs->stop (adev); --
Quoted 2 lines
2.17.1
_______________________________________________
amd-gfx mailing list
[email protected]
https://nam11.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.freedesktop.org%2Fmailman%2Flistinfo%2Famd-gfx&data=04%7C01%7Clijo.lazar%40amd.com%7C346c5521a1e848a40efe08d89b7a6ca7%7C3dd8961fe4884e608e11a82d994e183d%7C0%7C0%7C637430297401242320%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=6t589ueoS0x26%2FdpzSdtQmjkRygo4ez11t0GuBMacyg%3D&reserved=0
_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
Re: [PATCH 3/3] drm/amdgpu/pm: inform PMFW rlc status before start/stop rlc for vangogh
Quoted 5 lines · Lijo
[AMD Public Use]
Quoted 1 line
You can create two new callbacks in
ppt_funcs->inform_rlc(smu, on), and set on as bool typeWe can't keep adding ASIC specific workarounds as
ppt_funcs. We should make use of the existing ones or have something generic to handle these quirks. System features control is one generic place in the logic which is used to control features. It's used in dGPU context only now, but it may be repurposed for FW notifications.
Actually, it's the new API for all future APUs (gfx10 and later). So we want to add the callbacks. APU don't have the API to disable/enable DPM like dGPU because it's handled by sbios. Once we do suspend, before we stop RLC, we have to inform SMU to stop issuing the DPM request with this message.
And yes, I am fine to move it into system feature control. Because it noifies SMU to re-enable RLC again.
Quoted 73 lines
Thanks,
Lijo-----Original Message-----
From: amd-gfx <[email protected]> On Behalf Of Huang Rui
Sent: Tuesday, December 8, 2020 6:39 PM
To: Hou, Xiaomeng (Matthew) <[email protected]>
Cc: Deucher, Alexander <[email protected]>; Quan, Evan <[email protected]>; [email protected]
Subject: Re: [PATCH 3/3] drm/amdgpu/pm: inform PMFW rlc status before start/stop rlc for vangogh[CAUTION: External Email]
Quoted 17 lines · Xiaomeng (Matthew)
RLC is halted when system suspend/shutdown. However, due to DPM enabled, PMFM is unaware of RLC being halted and will continue sending messages, which would eventually caused ACPI related hang. So send message to inform PMFM the rlc status before start/stop rlc.
Signed-off-by Xiaomeng Hou <[email protected]>Change-Id I7b1a04f6e249ac6753109079ecb3019c99161d9f--- drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +0
-0drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c static int smu_smc_hw_setup(struct smu_context *smu) · line 924
Quoted 5 lines
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +2
-0@@ -920,6 +920,14 @@ static int smu_smc_hw_setup(struct smu_context *smu)uint32_t pcie_gen =0 , pcie_width =0 ;int ret =0 ; +if (adev->in_suspend && smu->is_apu) { + ret =smu_notify_rlc_status (smu,1 );You can create two new callbacks in
ppt_funcs->inform_rlc(smu, on), and set on as bool type.Then you can use below macros to implement this callback with RLC notify SMC message.
/* RLC Power Status */
#defineRLC_STATUS_OFF0
#defineRLC_STATUS_NORMAL1Others look good for me.
Thanks,
RayQuoted 23 lines
drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +6
-0+if (ret) { +dev_info (adev->dev,"Failed to notify rlc status!\n" ); +return ret; + } + } +if (adev->in_suspend &&smu_is_dpm_running (smu)) {dev_info (adev->dev,"dpm has been enabled\n" ); /* this is needed specifically */ @@ -1213,6 +1221,14 @@static int
smu_disable_dpms(struct smu_context *smu)dev_err(adev->dev, "Failed to disable smu features.\n"); }drivers/gpu/drm/amd/pm/swsmu/amdgpu_smu.c +8
-0+if (smu->is_apu) { + ret =smu_notify_rlc_status (smu,0 ); +if (ret) { +dev_info (adev->dev,"Failed to notify rlc status!\n" ); +return ret; + } + } +if (adev->asic_type >=CHIP_NAVI10 && adev->gfx.rlc.funcs->stop)
Quoted 8 lines
Quoted 4 lines
adev->gfx.rlc.funcs->stop(adev);--
2.17.1_______________________________________________
amd-gfx mailing list
[email protected]
https://nam11.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.freedesktop.org%2Fmailman%2Flistinfo%2Famd-gfx&data=04%7C01%7Clijo.lazar%40amd.com%7C346c5521a1e848a40efe08d89b7a6ca7%7C3dd8961fe4884e608e11a82d994e183d%7C0%7C0%7C637430297401242320%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=6t589ueoS0x26%2FdpzSdtQmjkRygo4ez11t0GuBMacyg%3D&reserved=0
_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx