imx: Add support for i.MX8MN Beacon EmbeddedWorks devkit.
Subsystems (3)
PATCH 1/1 imx: Add support for i.MX8MN Beacon EmbeddedWorks devkit.
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with the i.MX8M Mini.
arch/arm/dts/Makefile +1 -0
@@ -773,6 +773,7 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mn-ddr4-evk.dtb \ imx8mq-evk.dtb \ imx8mm-beacon-kit.dtb \ + imx8mn-beacon-kit.dtb \ imx8mq-phanbell.dtb \ imx8mp-evk.dtb \ imx8mq-pico-pi.dtb
arch/arm/dts/imx8mn-beacon-baseboard.dtsi new file +236 -0
236 lines not on this page · raw message
arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi new file +122 -0
122 lines not on this page · raw message
arch/arm/dts/imx8mn-beacon-kit.dts new file +19 -0
@@ -0,0 +1,19 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2020 Compass Electronics Group, LLC + */ + +/dts-v1/; + +#include "imx8mn.dtsi" +#include "imx8mn-beacon-som.dtsi" +#include "imx8mn-beacon-baseboard.dtsi" + +/ { + model = "Beacon EmbeddedWorks i.MX8M Nano Development Kit"; + compatible = "beacon,imx8mn-beacon-kit", "fsl,imx8mn"; + + chosen { + stdout-path = &uart2; + }; +};
arch/arm/dts/imx8mn-beacon-som.dtsi new file +405 -0
405 lines not on this page · raw message
arch/arm/mach-imx/imx8m/Kconfig +7 -0
@@ -72,6 +72,12 @@ config TARGET_IMX8MM_BEACON select SUPPORT_SPL select IMX8M_LPDDR4 +config TARGET_IMX8MN_BEACON + bool "imx8mn Beacon Embedded devkit" + select IMX8MN + select SUPPORT_SPL + select IMX8M_LPDDR4 + config TARGET_PHYCORE_IMX8MM bool "PHYTEC PHYCORE i.MX8MM" select IMX8MM
@@ -87,6 +93,7 @@ source "board/google/imx8mq_phanbell/Kconfig" source "board/technexion/pico-imx8mq/Kconfig" source "board/toradex/verdin-imx8mm/Kconfig" source "board/beacon/imx8mm/Kconfig" +source "board/beacon/imx8mn/Kconfig" source "board/phytec/phycore_imx8mm/Kconfig" endif
arch/arm/mach-imx/imx8m/imximage-8mn-lpddr4.cfg new file +17 -0
@@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2019 NXP + */ + +#define __ASSEMBLY__ + +FIT +ROM_VERSION v2 +BOOT_FROM sd +LOADER spl/u-boot-spl-ddr.bin 0x912000 +SECOND_LOADER u-boot.itb 0x40200000 0x60000 + +DDR_FW lpddr4_pmu_train_1d_imem.bin +DDR_FW lpddr4_pmu_train_1d_dmem.bin +DDR_FW lpddr4_pmu_train_2d_imem.bin +DDR_FW lpddr4_pmu_train_2d_dmem.bin
board/beacon/imx8mn/Kconfig new file +18 -0
@@ -0,0 +1,18 @@ +if TARGET_IMX8MN_BEACON + +config SYS_BOARD + default "imx8mn" + +config SYS_VENDOR + default "beacon" + +config SYS_CONFIG_NAME + default "imx8mn_beacon" + +config IMX8MN_FORCE_NOM_SOC + bool "Force to use nominal mode for SOC and ARM" + default n + +source "board/freescale/common/Kconfig" + +endif
board/beacon/imx8mn/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +i.MX8MN BEACON BOARD +M: Adam Ford <[email protected]> +S: Maintained +F: board/beacon/imx8mn/ +F: include/configs/imx8mn_beacon.h +F: configs/imx8mn_beacon_defconfig
board/beacon/imx8mn/Makefile new file +13 -0
@@ -0,0 +1,13 @@ +# +# Copyright 2020 Compass Electronics Group, LLC +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += imx8mn_beacon.o +obj-y += ../../freescale/common/ +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o +obj-$(CONFIG_IMX8M_DDR4) += ddr4_timing.o +endif
board/beacon/imx8mn/README new file +39 -0
@@ -0,0 +1,39 @@ +U-Boot for the Beacon EmbeddedWorks i.MX8M Nano Devkit + +Quick Start +=========== +- Build the ARM Trusted firmware binary +- Get ddr firmware +- Build U-Boot +- Boot + +Get and Build the ARM Trusted firmware +====================================== +Note: $(srctree) is U-Boot source directory + +$ git clone https://source.codeaurora.org/external/imx/imx-atf +$ git checkout imx_5.4.47_2.2.0 +$ make PLAT=imx8mn bl31 CROSS_COMPILE=aarch64-linux-gnu- +$ cp build/imx8mm/release/bl31.bin $(srctree) + +Get the DDR firmware +==================== +$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.5.bin +$ chmod +x firmware-imx-8.5.bin +$ ./firmware-imx-8.5 +$ cp firmware-imx-8.5/firmware/ddr/synopsys/lpddr4*.bin $(srctree) + +Build U-Boot +============ +$ make imx8mn_beacon_defconfig +$ make flash.bin CROSS_COMPILE=aarch64-linux-gnu- ATF_LOAD_ADDR=0x960000 + +Burn U-Boot to microSD Card +=========================== +$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32 + +Boot +==== +Set baseboard DIP switch: +S17: 1100XXXX +
board/beacon/imx8mn/imx8mn_beacon.c new file +56 -0
56 lines not on this page · raw message
board/beacon/imx8mn/lpddr4_timing.c new file +1434 -0
1,434 lines not on this page · raw message
board/beacon/imx8mn/spl.c new file +128 -0
128 lines not on this page · raw message
configs/imx8mn_beacon_defconfig new file +132 -0
132 lines not on this page · raw message
include/configs/imx8mn_beacon.h new file +155 -0
155 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH 1/1 imx: Add support for i.MX8MN Beacon EmbeddedWorks devkit.
Hello Adam,
Quoted 18 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Adam Ford
Sent: Thursday, December 10, 2020 5:08 PM
To: u-boot at lists.denx.de
Cc: aford at beaconembedded.com; Adam Ford <[email protected]>; Stefano Babic <[email protected]>; Fabio Estevam <[email protected]>; NXP i.MX U- Boot Team <[email protected]>
Subject: [PATCH] imx: Add support for i.MX8MN Beacon EmbeddedWorks devkit.Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with the i.MX8M Mini.
Signed-off-by Adam Ford <[email protected]>
<snip>
Quoted 17 lines
board/beacon/imx8mn/README new file +11
-0@@ -0,0 +1,39 @@ +U-Boot for the Beacon EmbeddedWorks i.MX8M Nano Devkit + +Quick Start +=========== +- Build the ARM Trusted firmware binary +- Get ddr firmware +- Build U-Boot +- Boot + +Get and Build the ARM Trusted firmware +======================================
board/beacon/imx8mn/README line 21
Quoted 10 lines
board/beacon/imx8mn/README new file +10
-0+Note: $(srctree) is U-Boot source directory + +$ git clone https://source.codeaurora.org/external/imx/imx-atf +$ git checkout imx_5.4.47_2.2.0 +$ make PLAT=imx8mn bl31 CROSS_COMPILE=aarch64-linux-gnu- +$ cp build/imx8mm/release/bl31.bin $(srctree) + +Get the DDR firmware +==================== +$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.5.bin
There is a newer version of DDR firmware available from NXP:
https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin
It is also aligned with imx_5.4.47_2.2.0 ATF release, so for completeness purposes I would recommend you to include the updated link into README file.
Yocto meta-freescale layer is already using this firmware version for mx8m series [1], and it is operable.
I believe it would be beneficial to recommend users to pull the latest version available.
Quoted 19 lines
board/beacon/imx8mn/README new file +8
-0+$ chmod +x firmware-imx-8.5.bin +$ ./firmware-imx-8.5 +$ cp firmware-imx-8.5/firmware/ddr/synopsys/lpddr4*.bin $(srctree) + +Build U-Boot +============ +$ make imx8mn_beacon_defconfig +$ make flash.bin CROSS_COMPILE=aarch64-linux-gnu-ATF_LOAD_ADDR=0x960000
board/beacon/imx8mn/README new file +10
-0+ +Burn U-Boot to microSD Card +=========================== +$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32 + +Boot +==== +Set baseboard DIP switch: +S17: 1100XXXX +
<snip>
Quoted 1 line
2.25.1
-- andrey