4.19.163-rc1 review

This is the start of the stable review cycle for the 4.19.163 release. There are 39 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 12 Dec 2020 14:25:47 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.163-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 4.19.163-rc1

Masami Hiramatsu <[email protected]>
x86/insn-eval: Use new for_each_insn_prefix() macro to loop over prefixes bytes

Florian Westphal <[email protected]>
netfilter: nf_tables: avoid false-postive lockdep splat

Luo Meng <[email protected]>
Input: i8042 - fix error return code in i8042_setup_aux()

Mike Snitzer <[email protected]>
dm writecache: remove BUG() and fail gracefully instead

Zhihao Cheng <[email protected]>
i2c: qup: Fix error return code in qup_i2c_bam_schedule_desc()

Bob Peterson <[email protected]>
gfs2: check for empty rgrp tree in gfs2_ri_update

Steven Rostedt (VMware) <[email protected]>
tracing: Fix userstacktrace option for instances

Peter Ujfalusi <[email protected]>
spi: bcm2835: Release the DMA channel if probe fails after dma_init

Lukas Wunner <[email protected]>
spi: bcm2835: Fix use-after-free on unbind

Lukas Wunner <[email protected]>
spi: bcm-qspi: Fix use-after-free on unbind

Lukas Wunner <[email protected]>
spi: Introduce device-managed SPI controller allocation

Suravee Suthikulpanit <[email protected]>
iommu/amd: Set DTE[IntTabLen] to represent 512 IRTEs

Samuel Thibault <[email protected]>
speakup: Reject setting the speakup line discipline outside of speakup

Christian Eggers <[email protected]>
i2c: imx: Check for I2SR_IAL after every byte

Christian Eggers <[email protected]>
i2c: imx: Fix reset of I2SR_IAL flag

Masami Hiramatsu <[email protected]>
x86/uprobes: Do not use prefixes.nbytes when looping over prefixes.bytes

Qian Cai <[email protected]>
mm/swapfile: do not sleep with a spin lock held

Yang Shi <[email protected]>
mm: list_lru: set shrinker map bit when child nr_items is not zero

Mike Snitzer <[email protected]>
dm: remove invalid sparse __acquires and __releases annotations

Mikulas Patocka <[email protected]>
dm writecache: fix the maximum number of arguments

Suganath Prabu S <[email protected]>
scsi: mpt3sas: Fix ioctl timeout

Christian Eggers <[email protected]>
i2c: imx: Don't generate STOP condition if arbitration has been lost

Paulo Alcantara <[email protected]>
cifs: fix potential use-after-free in cifs_echo_request()

Naveen N. Rao <[email protected]>
ftrace: Fix updating FTRACE_FL_TRAMP

Takashi Iwai <[email protected]>
ALSA: hda/generic: Add option to enforce preferred_dacs pairs

Kailang Yang <[email protected]>
ALSA: hda/realtek - Add new codec supported for ALC897

Jian-Hong Pan <[email protected]>
ALSA: hda/realtek: Enable headset of ASUS UX482EG & B9400CEA with ALC294

Takashi Iwai <[email protected]>
ALSA: hda/realtek: Add mute LED quirk to yet another HP x360 model

Jann Horn <[email protected]>

    tty: Fix ->session locking

Jann Horn <[email protected]>

    tty: Fix ->pgrp locking in tiocspgrp()

Bjørn Mork <[email protected]>
USB: serial: option: fix Quectel BG96 matching

Giacinto Cifelli <[email protected]>
USB: serial: option: add support for Thales Cinterion EXS82

Vincent Palatin <[email protected]>
USB: serial: option: add Fibocom NL668 variants

Johan Hovold <[email protected]>
USB: serial: ch341: sort device-id entries

Jan-Niklas Burfeind <[email protected]>
USB: serial: ch341: add new Product ID for CH341A

Johan Hovold <[email protected]>
USB: serial: kl5kusb105: fix memleak on open

Vamsi Krishna Samavedam <[email protected]>
usb: gadget: f_fs: Use local copy of descriptors for userspace copy

Hans de Goede <[email protected]>
pinctrl: baytrail: Fix pin being driven low for a while on gpiod_get(..., GPIOD_OUT_HIGH)

Hans de Goede <[email protected]>
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output

-------------

Diffstat:

 Makefile                                  |  4 +-
 arch/x86/include/asm/insn.h               | 15 +++++++
 arch/x86/kernel/uprobes.c                 | 10 +++--
 arch/x86/lib/insn-eval.c                  |  5 ++-
 drivers/i2c/busses/i2c-imx.c              | 42 +++++++++++++++----
 drivers/i2c/busses/i2c-qup.c              |  3 +-
 drivers/input/serio/i8042.c               |  3 +-
 drivers/iommu/amd_iommu_types.h           |  2 +-
 drivers/md/dm-writecache.c                |  4 +-
 drivers/md/dm.c                           |  2 -
 drivers/pinctrl/intel/pinctrl-baytrail.c  | 67 ++++++++++++++++++++++++-------
 drivers/scsi/mpt3sas/mpt3sas_ctl.c        |  2 +-
 drivers/spi/spi-bcm-qspi.c                | 34 ++++++----------
 drivers/spi/spi-bcm2835.c                 | 22 +++++-----
 drivers/spi/spi.c                         | 58 +++++++++++++++++++++++++-
 drivers/staging/speakup/spk_ttyio.c       | 37 ++++++++++-------
 drivers/tty/tty_io.c                      |  7 +++-
 drivers/tty/tty_jobctrl.c                 | 44 ++++++++++++++------
 drivers/usb/gadget/function/f_fs.c        |  6 ++-
 drivers/usb/serial/ch341.c                |  5 ++-
 drivers/usb/serial/kl5kusb105.c           | 10 ++---
 drivers/usb/serial/option.c               | 10 +++--
 fs/cifs/connect.c                         |  2 +
 fs/gfs2/rgrp.c                            |  4 ++
 include/linux/spi/spi.h                   | 19 +++++++++
 include/linux/tty.h                       |  4 ++
 kernel/trace/ftrace.c                     | 22 +++++++++-
 kernel/trace/trace.c                      |  7 ++--
 kernel/trace/trace.h                      |  6 ++-
 mm/list_lru.c                             | 10 ++---
 mm/swapfile.c                             |  4 +-
 net/netfilter/nf_tables_api.c             |  3 +-
 sound/pci/hda/hda_generic.c               | 12 ++++--
 sound/pci/hda/hda_generic.h               |  1 +
 sound/pci/hda/patch_realtek.c             |  6 +++
 tools/objtool/arch/x86/include/asm/insn.h | 15 +++++++
 tools/perf/util/intel-pt-decoder/insn.h   | 15 +++++++
 37 files changed, 390 insertions(+), 132 deletions(-)

From: Hans de Goede <[email protected]>

commit e2b74419e5cc7cfc58f3e785849f73f8fa0af5b3 upstream

Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode.

On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI resource so we can do this without problems as long as we release the IRQ before changing the pin to output mode.

On Bay Trail devices with a Goodix touchscreen direct-irq mode is used in combination with listing the pin as a normal GpioIo resource. This works fine, but this triggers the WARN in byt_gpio_set_direction-s output path because direct-irq support is enabled on the pin.

This commit replaces the WARN call with a dev_info_once call, fixing a bunch of WARN splats in dmesg on each suspend/resume cycle.

---
 drivers/pinctrl/intel/pinctrl-baytrail.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

index acb02a7aa9496..7d6685ae31d70 100644
@@ -1026,15 +1026,15 @@ static int byt_gpio_set_direction(struct pinctrl_dev *pctl_dev,
 	value &= ~BYT_DIR_MASK;
 	if (input)
 		value |= BYT_OUTPUT_EN;
-	else
+	else if (readl(conf_reg) & BYT_DIRECT_IRQ_EN)
 		/*
 		 * Before making any direction modifications, do a check if gpio
 		 * is set for direct IRQ.  On baytrail, setting GPIO to output
-		 * does not make sense, so let's at least warn the caller before
+		 * does not make sense, so let's at least inform the caller before
 		 * they shoot themselves in the foot.
 		 */
-		WARN(readl(conf_reg) & BYT_DIRECT_IRQ_EN,
-		     "Potential Error: Setting GPIO with direct_irq_en to output");
+		dev_info_once(vg->dev, "Potential Error: Setting GPIO with direct_irq_en to output");
+
 	writel(value, val_reg);
 
 	raw_spin_unlock_irqrestore(&byt_lock, flags);

2.27.0

From: Hans de Goede <[email protected]>

commit 156abe2961601d60a8c2a60c6dc8dd6ce7adcdaf upstream

The pins on the Bay Trail SoC have separate input-buffer and output-buffer enable bits and a read of the level bit of the value register will always return the value from the input-buffer.

The BIOS of a device may configure a pin in output-only mode, only enabling the output buffer, and write 1 to the level bit to drive the pin high. This 1 written to the level bit will be stored inside the data-latch of the output buffer.

But a subsequent read of the value register will return 0 for the level bit because the input-buffer is disabled. This causes a read-modify-write as done by byt_gpio_set_direction() to write 0 to the level bit, driving the pin low!

Before this commit byt_gpio_direction_output() relied on pinctrl_gpio_direction_output() to set the direction, followed by a call to byt_gpio_set() to apply the selected value. This causes the pin to go low between the pinctrl_gpio_direction_output() and byt_gpio_set() calls.

Change byt_gpio_direction_output() to directly make the register modifications itself instead. Replacing the 2 subsequent writes to the value register with a single write.

Note that the pinctrl code does not keep track internally of the direction, so not going through pinctrl_gpio_direction_output() is not an issue.

This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is already on at boot (no external monitor connected), then the i915 driver does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The temporarily going low of that GPIO was causing the panel to reset itself after which it would not show an image until it was turned off and back on again (until a full modeset was done on it). This commit fixes this.

This commit also updates the byt_gpio_direction_input() to use direct register accesses instead of going through pinctrl_gpio_direction_input(), to keep it consistent with byt_gpio_direction_output().

Note for backporting, this commit depends on:
commit e2b74419e5cc ("pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output")

---
 drivers/pinctrl/intel/pinctrl-baytrail.c | 67 +++++++++++++++++++-----
 1 file changed, 53 insertions(+), 14 deletions(-)

index 7d6685ae31d70..1b00a3f3b419c 100644
@@ -1009,6 +1009,21 @@ static void byt_gpio_disable_free(struct pinctrl_dev *pctl_dev,
 	pm_runtime_put(&vg->pdev->dev);
 }
 
+static void byt_gpio_direct_irq_check(struct byt_gpio *vg,
+				      unsigned int offset)
+{
+	void __iomem *conf_reg = byt_gpio_reg(vg, offset, BYT_CONF0_REG);
+
+	/*
+	 * Before making any direction modifications, do a check if gpio is set
+	 * for direct IRQ. On Bay Trail, setting GPIO to output does not make
+	 * sense, so let's at least inform the caller before they shoot
+	 * themselves in the foot.
+	 */
+	if (readl(conf_reg) & BYT_DIRECT_IRQ_EN)
+		dev_info_once(&vg->pdev->dev, "Potential Error: Setting GPIO with direct_irq_en to output");
+}
+
 static int byt_gpio_set_direction(struct pinctrl_dev *pctl_dev,
 				  struct pinctrl_gpio_range *range,
 				  unsigned int offset,

@@ -1016,7 +1031,6 @@ static int byt_gpio_set_direction(struct pinctrl_dev *pctl_dev,
 {
 	struct byt_gpio *vg = pinctrl_dev_get_drvdata(pctl_dev);
 	void __iomem *val_reg = byt_gpio_reg(vg, offset, BYT_VAL_REG);
-	void __iomem *conf_reg = byt_gpio_reg(vg, offset, BYT_CONF0_REG);
 	unsigned long flags;
 	u32 value;
 

@@ -1026,14 +1040,8 @@ static int byt_gpio_set_direction(struct pinctrl_dev *pctl_dev,
 	value &= ~BYT_DIR_MASK;
 	if (input)
 		value |= BYT_OUTPUT_EN;
-	else if (readl(conf_reg) & BYT_DIRECT_IRQ_EN)
-		/*
-		 * Before making any direction modifications, do a check if gpio
-		 * is set for direct IRQ.  On baytrail, setting GPIO to output
-		 * does not make sense, so let's at least inform the caller before
-		 * they shoot themselves in the foot.
-		 */
-		dev_info_once(vg->dev, "Potential Error: Setting GPIO with direct_irq_en to output");
+	else
+		byt_gpio_direct_irq_check(vg, offset);
 
 	writel(value, val_reg);
 

@@ -1374,19 +1382,50 @@ static int byt_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
 
 static int byt_gpio_direction_input(struct gpio_chip *chip, unsigned int offset)
 {
-	return pinctrl_gpio_direction_input(chip->base + offset);
+	struct byt_gpio *vg = gpiochip_get_data(chip);
+	void __iomem *val_reg = byt_gpio_reg(vg, offset, BYT_VAL_REG);
+	unsigned long flags;
+	u32 reg;
+
+	raw_spin_lock_irqsave(&byt_lock, flags);
+
+	reg = readl(val_reg);
+	reg &= ~BYT_DIR_MASK;
+	reg |= BYT_OUTPUT_EN;
+	writel(reg, val_reg);
+
+	raw_spin_unlock_irqrestore(&byt_lock, flags);
+	return 0;
 }
 
+/*
+ * Note despite the temptation this MUST NOT be converted into a call to
+ * pinctrl_gpio_direction_output() + byt_gpio_set() that does not work this
+ * MUST be done as a single BYT_VAL_REG register write.
+ * See the commit message of the commit adding this comment for details.
+ */
 static int byt_gpio_direction_output(struct gpio_chip *chip,
 				     unsigned int offset, int value)
 {
-	int ret = pinctrl_gpio_direction_output(chip->base + offset);
+	struct byt_gpio *vg = gpiochip_get_data(chip);
+	void __iomem *val_reg = byt_gpio_reg(vg, offset, BYT_VAL_REG);
+	unsigned long flags;
+	u32 reg;
 
-	if (ret)
-		return ret;
+	raw_spin_lock_irqsave(&byt_lock, flags);
 
-	byt_gpio_set(chip, offset, value);
+	byt_gpio_direct_irq_check(vg, offset);
 
+	reg = readl(val_reg);
+	reg &= ~BYT_DIR_MASK;
+	if (value)
+		reg |= BYT_LEVEL;
+	else
+		reg &= ~BYT_LEVEL;
+
+	writel(reg, val_reg);
+
+	raw_spin_unlock_irqrestore(&byt_lock, flags);
 	return 0;
 }
 

2.27.0

From: Vamsi Krishna Samavedam <[email protected]>

commit a4b98a7512f18534ce33a7e98e49115af59ffa00 upstream.

The function may be unbound causing the ffs_ep and its descriptors to be freed while userspace is in the middle of an ioctl requesting the same descriptors. Avoid dangling pointer reference by first making a local copy of desctiptors before releasing the spinlock.

---
 drivers/usb/gadget/function/f_fs.c |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

@@ -1243,7 +1243,7 @@ static long ffs_epfile_ioctl(struct file
 	case FUNCTIONFS_ENDPOINT_DESC:
 	{
 		int desc_idx;
-		struct usb_endpoint_descriptor *desc;
+		struct usb_endpoint_descriptor desc1, *desc;
 
 		switch (epfile->ffs->gadget->speed) {
 		case USB_SPEED_SUPER:

@@ -1255,10 +1255,12 @@ static long ffs_epfile_ioctl(struct file
 		default:
 			desc_idx = 0;
 		}
+
 		desc = epfile->ep->descs[desc_idx];
+		memcpy(&desc1, desc, desc->bLength);
 
 		spin_unlock_irq(&epfile->ffs->eps_lock);
-		ret = copy_to_user((void __user *)value, desc, desc->bLength);
+		ret = copy_to_user((void __user *)value, &desc1, desc1.bLength);
 		if (ret)
 			ret = -EFAULT;
 		return ret;

From: Johan Hovold <[email protected]>

commit 3f203f057edfcf6bd02c6b942799262bfcf31f73 upstream.

Fix memory leak of control-message transfer buffer on successful open().

---
 drivers/usb/serial/kl5kusb105.c |   10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)

@@ -276,12 +276,12 @@ static int  klsi_105_open(struct tty_str
 	priv->cfg.unknown2 = cfg->unknown2;
 	spin_unlock_irqrestore(&priv->lock, flags);
 
+	kfree(cfg);
+
 	/* READ_ON and urb submission */
 	rc = usb_serial_generic_open(tty, port);
-	if (rc) {
-		retval = rc;
-		goto err_free_cfg;
-	}
+	if (rc)
+		return rc;
 
 	rc = usb_control_msg(port->serial->dev,
 			     usb_sndctrlpipe(port->serial->dev, 0),

@@ -324,8 +324,6 @@ err_disable_read:
 			     KLSI_TIMEOUT);
 err_generic_close:
 	usb_serial_generic_close(port);
-err_free_cfg:
-	kfree(cfg);
 
 	return retval;
 }

From: Jan-Niklas Burfeind <[email protected]>

commit 46ee4abb10a07bd8f8ce910ee6b4ae6a947d7f63 upstream.

Add PID for CH340 that's found on a ch341 based Programmer made by keeyees. The specific device that contains the serial converter is described
here: http://www.keeyees.com/a/Products/ej/36.html

The driver works flawlessly as soon as the new PID (0x5512) is added to it.

---
 drivers/usb/serial/ch341.c |    1 +
 1 file changed, 1 insertion(+)

@@ -83,6 +83,7 @@ static const struct usb_device_id id_tab
 	{ USB_DEVICE(0x4348, 0x5523) },
 	{ USB_DEVICE(0x1a86, 0x7522) },
 	{ USB_DEVICE(0x1a86, 0x7523) },
+	{ USB_DEVICE(0x1a86, 0x5512) },
 	{ USB_DEVICE(0x1a86, 0x5523) },
 	{ },
 };

From: Johan Hovold <[email protected]>

commit bf193bfc12dbc3754fc8a6e0e1e3702f1af2f772 upstream.

Keep the device-id entries sorted to make it easier to add new ones in the right spot.

---
 drivers/usb/serial/ch341.c |    6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

@@ -80,11 +80,11 @@
 #define CH341_LCR_CS5          0x00
 
 static const struct usb_device_id id_table[] = {
-	{ USB_DEVICE(0x4348, 0x5523) },
-	{ USB_DEVICE(0x1a86, 0x7522) },
-	{ USB_DEVICE(0x1a86, 0x7523) },
 	{ USB_DEVICE(0x1a86, 0x5512) },
 	{ USB_DEVICE(0x1a86, 0x5523) },
+	{ USB_DEVICE(0x1a86, 0x7522) },
+	{ USB_DEVICE(0x1a86, 0x7523) },
+	{ USB_DEVICE(0x4348, 0x5523) },
 	{ },
 };
 MODULE_DEVICE_TABLE(usb, id_table);

From: Vincent Palatin <[email protected]>

commit 5e4d659b10fde14403adb2e215df4a3168fe8465 upstream.

Update the USB serial option driver support for the Fibocom NL668 Cat.4 LTE modules as there are actually several different variants. Got clarifications from Fibocom, there are distinct products:
- VID:PID 1508:1001, NL668 for IOT (no MBIM interface)
- VID:PID 2cb7:01a0, NL668-AM and NL652-EU are laptop M.2 cards (with MBIM interfaces for Windows/Linux/Chrome OS), respectively for Americas and Europe.

usb-devices output for the laptop M.2 cards:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2cb7 ProdID=01a0 Rev=03.18
S:  Manufacturer=Fibocom Wireless Inc.
S:  Product=Fibocom NL652-EU Modem
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

---
 drivers/usb/serial/option.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

@@ -2046,12 +2046,13 @@ static const struct usb_device_id option
 	  .driver_info = RSVD(0) | RSVD(1) | RSVD(6) },
 	{ USB_DEVICE(0x0489, 0xe0b5),						/* Foxconn T77W968 ESIM */
 	  .driver_info = RSVD(0) | RSVD(1) | RSVD(6) },
-	{ USB_DEVICE(0x1508, 0x1001),						/* Fibocom NL668 */
+	{ USB_DEVICE(0x1508, 0x1001),						/* Fibocom NL668 (IOT version) */
 	  .driver_info = RSVD(4) | RSVD(5) | RSVD(6) },
 	{ USB_DEVICE(0x2cb7, 0x0104),						/* Fibocom NL678 series */
 	  .driver_info = RSVD(4) | RSVD(5) },
 	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff),			/* Fibocom NL678 series */
 	  .driver_info = RSVD(6) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a0, 0xff) },			/* Fibocom NL668-AM/NL652-EU (laptop MBIM) */
 	{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff) },			/* GosunCn GM500 RNDIS */
 	{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff) },			/* GosunCn GM500 MBIM */
 	{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1406, 0xff) },			/* GosunCn GM500 ECM/NCM */

From: Giacinto Cifelli <[email protected]>

commit 6d6556c04ebaeaf4e7fa8b791c97e2a7c41b38a3 upstream.

There is a single option port in this modem, and it is used as debug port.

lsusb -v for this device:

Bus 001 Device 002: ID 1e2d:006c
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2 ?
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x1e2d
idProduct 0x006c
bcdDevice 0.00

  iManufacturer           4
  iProduct                3
  iSerial                 5
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 243
bNumInterfaces 7
bConfigurationValue 1
iConfiguration 2
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 1
bInterfaceCount 2
bFunctionClass 2 Communications
bFunctionSubClass 2 Abstract (modem)
bFunctionProtocol 1 AT-commands (v.25ter)
iFunction 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 2
CDC Union:
bMasterInterface 1
bSlaveInterface 2
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 3
bInterfaceCount 2
bFunctionClass 2 Communications
bFunctionSubClass 2 Abstract (modem)
bFunctionProtocol 1 AT-commands (v.25ter)
iFunction 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 4
CDC Union:
bMasterInterface 3
bSlaveInterface 4
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 5
bInterfaceCount 2
bFunctionClass 2 Communications
bFunctionSubClass 2 Abstract (modem)
bFunctionProtocol 1 AT-commands (v.25ter)
iFunction 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 5
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 6 Ethernet Networking
bInterfaceProtocol 0
iInterface 0
CDC Header:
bcdCDC 1.10
CDC Ethernet:
iMacAddress 1 (??)
bmEthernetStatistics 0x00000000
wMaxSegmentSize 16384
wNumberMCFilters 0x0001
bNumberPowerFilters 0
CDC Union:
bMasterInterface 5
bSlaveInterface 6
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 6
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 6
bAlternateSetting 1
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0

---
 drivers/usb/serial/option.c |    2 ++
 1 file changed, 2 insertions(+)

@@ -419,6 +419,7 @@ static void option_instat_callback(struc
 #define CINTERION_PRODUCT_PH8			0x0053
 #define CINTERION_PRODUCT_AHXX			0x0055
 #define CINTERION_PRODUCT_PLXX			0x0060
+#define CINTERION_PRODUCT_EXS82			0x006c
 #define CINTERION_PRODUCT_PH8_2RMNET		0x0082
 #define CINTERION_PRODUCT_PH8_AUDIO		0x0083
 #define CINTERION_PRODUCT_AHXX_2RMNET		0x0084

@@ -1902,6 +1903,7 @@ static const struct usb_device_id option
 	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_AHXX_AUDIO, 0xff) },
 	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_CLS8, 0xff),
 	  .driver_info = RSVD(0) | RSVD(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(CINTERION_VENDOR_ID, CINTERION_PRODUCT_EXS82, 0xff) },
 	{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDM) },
 	{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDMNET) },
 	{ USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC25_MDM) },

From: Bjørn Mork <[email protected]>

commit c98fff7332dbd6e028969f8c2bda3d7bc7a024d8 upstream.

This is a partial revert of commit 2bb70f0a4b23 ("USB: serial:
option: support dynamic Quectel USB compositions")

The Quectel BG96 is different from most other modern Quectel modems, having serial functions with 3 endpoints using ff/ff/ff and ff/fe/ff class/subclass/protocol. Including it in the change to accommodate dynamic function mapping was incorrect.

Revert to interface number matching for the BG96, assuming static layout of the RMNET function on interface 4. This restores support for the serial functions on interfaces 2 and 3.

Full lsusb output for the BG96:

Bus 002 Device 003: ID 2c7c:0296
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00

 bDeviceClass            0 (Defined at Interface level)
 bDeviceSubClass         0
 bDeviceProtocol         0
 bMaxPacketSize0        64
 idVendor           0x2c7c
 idProduct          0x0296
 bcdDevice            0.00
 iManufacturer           3 Qualcomm, Incorporated
 iProduct                2 Qualcomm CDMA Technologies MSM
 iSerial                 4 d1098243
 bNumConfigurations      1
 Configuration Descriptor:
   bLength                 9
   bDescriptorType         2
   wTotalLength          145
   bNumInterfaces          5
   bConfigurationValue     1
   iConfiguration          1 Qualcomm Configuration
   bmAttributes         0xe0
     Self Powered
     Remote Wakeup
   MaxPower              500mA
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        0
     bAlternateSetting       0
     bNumEndpoints           2
     bInterfaceClass       255 Vendor Specific Class
     bInterfaceSubClass    255 Vendor Specific Subclass
     bInterfaceProtocol    255 Vendor Specific Protocol
     iInterface              0
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x81  EP 1 IN
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               0
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x01  EP 1 OUT
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               0
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        1
     bAlternateSetting       0
     bNumEndpoints           2
     bInterfaceClass       255 Vendor Specific Class
     bInterfaceSubClass    255 Vendor Specific Subclass
     bInterfaceProtocol    255 Vendor Specific Protocol
     iInterface              0
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x82  EP 2 IN
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               0
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x02  EP 2 OUT
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               0
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        2
     bAlternateSetting       0
     bNumEndpoints           3
     bInterfaceClass       255 Vendor Specific Class
     bInterfaceSubClass    255 Vendor Specific Subclass
     bInterfaceProtocol    255 Vendor Specific Protocol
     iInterface              0
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x83  EP 3 IN
       bmAttributes            3
         Transfer Type            Interrupt
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0040  1x 64 bytes
       bInterval               5
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x84  EP 4 IN
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               0
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x03  EP 3 OUT
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               0
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        3
     bAlternateSetting       0
     bNumEndpoints           3
     bInterfaceClass       255 Vendor Specific Class
     bInterfaceSubClass    254
     bInterfaceProtocol    255
     iInterface              0
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x85  EP 5 IN
       bmAttributes            3
         Transfer Type            Interrupt
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0040  1x 64 bytes
       bInterval               5
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x86  EP 6 IN
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               0
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x04  EP 4 OUT
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               0
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        4
     bAlternateSetting       0
     bNumEndpoints           3
     bInterfaceClass       255 Vendor Specific Class
     bInterfaceSubClass    255 Vendor Specific Subclass
     bInterfaceProtocol    255 Vendor Specific Protocol

iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00

 bDeviceClass            0 (Defined at Interface level)
 bDeviceSubClass         0
 bDeviceProtocol         0

bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)

---
 drivers/usb/serial/option.c |    5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

@@ -1106,9 +1106,8 @@ static const struct usb_device_id option
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EG95, 0xff, 0xff, 0xff),
 	  .driver_info = NUMEP2 },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EG95, 0xff, 0, 0) },
-	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_BG96, 0xff, 0xff, 0xff),
-	  .driver_info = NUMEP2 },
-	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_BG96, 0xff, 0, 0) },
+	{ USB_DEVICE(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_BG96),
+	  .driver_info = RSVD(4) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0xff, 0xff),
 	  .driver_info = RSVD(1) | RSVD(2) | RSVD(3) | RSVD(4) | NUMEP2 },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },

From: Jann Horn <[email protected]>

commit 54ffccbf053b5b6ca4f6e45094b942fab92a25fc upstream.

tiocspgrp() takes two tty_struct pointers: One to the tty that userspace passed to ioctl() (tty) and one to the TTY being changed (real_tty). These pointers are different when ioctl() is called with a master fd.

To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.

This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on both sides of a PTY pair to corrupt the refcount of struct pid, leading to use-after-free errors.

---
 drivers/tty/tty_jobctrl.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -494,10 +494,10 @@ static int tiocspgrp(struct tty_struct *
 	if (session_of_pgrp(pgrp) != task_session(current))
 		goto out_unlock;
 	retval = 0;
-	spin_lock_irq(&tty->ctrl_lock);
+	spin_lock_irq(&real_tty->ctrl_lock);
 	put_pid(real_tty->pgrp);
 	real_tty->pgrp = get_pid(pgrp);
-	spin_unlock_irq(&tty->ctrl_lock);
+	spin_unlock_irq(&real_tty->ctrl_lock);
 out_unlock:
 	rcu_read_unlock();
 	return retval;

From: Jann Horn <[email protected]>

commit c8bcd9c5be24fb9e6132e97da5a35e55a83e36b9 upstream.

Currently, locking of ->session is very inconsistent; most places protect it using the legacy tty mutex, but disassociate_ctty(), __do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for ->pgrp), but __proc_set_tty() doesn't do that yet.

On a PREEMPT=y system, an unprivileged user can theoretically abuse this broken locking to read 4 bytes of freed memory via TIOCGSID if tiocgsid() is preempted long enough at the right point. (Other things might also go wrong, especially if root-only ioctls are involved; I'm not sure about that.)

Change the locking on ->session such that:

- tty_lock() is held by all writers: By making disassociate_ctty() hold it. This should be fine because the same lock can already be taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by siglock to be able to take tty_lock() without ugly retry logic; as far as I can tell, this should be fine, since nothing in the signal_struct is touched in the if (tty) branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By adding locking to tiocgsid() and __do_SAK(), and expanding the area covered by ctrl_lock in tiocspgrp().

---
 drivers/tty/tty_io.c      |    7 ++++++-
 drivers/tty/tty_jobctrl.c |   44 +++++++++++++++++++++++++++++++-------------
 include/linux/tty.h       |    4 ++++
 3 files changed, 41 insertions(+), 14 deletions(-)

@@ -2747,10 +2747,14 @@ void __do_SAK(struct tty_struct *tty)
 	struct task_struct *g, *p;
 	struct pid *session;
 	int		i;
+	unsigned long flags;
 
 	if (!tty)
 		return;
-	session = tty->session;
+
+	spin_lock_irqsave(&tty->ctrl_lock, flags);
+	session = get_pid(tty->session);
+	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
 
 	tty_ldisc_flush(tty);
 

@@ -2782,6 +2786,7 @@ void __do_SAK(struct tty_struct *tty)
 		task_unlock(p);
 	} while_each_thread(g, p);
 	read_unlock(&tasklist_lock);
+	put_pid(session);
 #endif
 }
 

@@ -306,6 +306,10 @@ struct tty_struct {
 	struct termiox *termiox;	/* May be NULL for unsupported */
 	char name[64];
 	struct pid *pgrp;		/* Protected by ctrl lock */
+	/*
+	 * Writes protected by both ctrl lock and legacy mutex, readers must use
+	 * at least one of them.
+	 */
 	struct pid *session;
 	unsigned long flags;
 	int count;

From: Takashi Iwai <[email protected]>

commit aeedad2504997be262c98f6e3228173225a8d868 upstream.

HP Spectre x360 Convertible 15" version (SSID 103c:827f) needs the same quirk to make the mute LED working like other models.
System Information
Manufacturer: HP
Product Name: HP Spectre x360 Convertible 15-bl1XX

Sound Codec:

    Codec: Realtek ALC295
    Vendor Id: 0x10ec0295
    Subsystem Id: 0x103c827f
    Revision Id: 0x100002

---
 sound/pci/hda/patch_realtek.c |    1 +
 1 file changed, 1 insertion(+)

@@ -7068,6 +7068,7 @@ static const struct snd_pci_quirk alc269
 	SND_PCI_QUIRK(0x103c, 0x820d, "HP Pavilion 15", ALC269_FIXUP_HP_MUTE_LED_MIC3),
 	SND_PCI_QUIRK(0x103c, 0x8256, "HP", ALC221_FIXUP_HP_FRONT_MIC),
 	SND_PCI_QUIRK(0x103c, 0x827e, "HP x360", ALC295_FIXUP_HP_X360),
+	SND_PCI_QUIRK(0x103c, 0x827f, "HP x360", ALC269_FIXUP_HP_MUTE_LED_MIC3),
 	SND_PCI_QUIRK(0x103c, 0x82bf, "HP G3 mini", ALC221_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x82c0, "HP G3 mini premium", ALC221_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x83b9, "HP Spectre x360", ALC269_FIXUP_HP_MUTE_LED_MIC3),

From: Jian-Hong Pan <[email protected]>

commit eeacd80fcb29b769ea915cd06b7dd35e0bf0bc25 upstream.

Some laptops like ASUS UX482EG & B9400CEA's headset audio does not work until the quirk ALC294_FIXUP_ASUS_HPE is applied.

---
 sound/pci/hda/patch_realtek.c |    3 +++
 1 file changed, 3 insertions(+)

@@ -7778,6 +7778,9 @@ static const struct snd_hda_pin_quirk al
 	SND_HDA_PIN_QUIRK(0x10ec0293, 0x1028, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE,
 		ALC292_STANDARD_PINS,
 		{0x13, 0x90a60140}),
+	SND_HDA_PIN_QUIRK(0x10ec0294, 0x1043, "ASUS", ALC294_FIXUP_ASUS_HPE,
+		{0x17, 0x90170110},
+		{0x21, 0x04211020}),
 	SND_HDA_PIN_QUIRK(0x10ec0294, 0x1043, "ASUS", ALC294_FIXUP_ASUS_MIC,
 		{0x14, 0x90170110},
 		{0x1b, 0x90a70130},

From: Kailang Yang <[email protected]>

commit e5782a5d5054bf1e03cb7fbd87035037c2a22698 upstream.

Enable new codec supported for ALC897.

---
 sound/pci/hda/patch_realtek.c |    2 ++
 1 file changed, 2 insertions(+)

@@ -439,6 +439,7 @@ static void alc_fill_eapd_coef(struct hd
 			alc_update_coef_idx(codec, 0x7, 1<<5, 0);
 		break;
 	case 0x10ec0892:
+	case 0x10ec0897:
 		alc_update_coef_idx(codec, 0x7, 1<<5, 0);
 		break;
 	case 0x10ec0899:

@@ -9166,6 +9167,7 @@ static const struct hda_device_id snd_hd
 	HDA_CODEC_ENTRY(0x10ec0888, "ALC888", patch_alc882),
 	HDA_CODEC_ENTRY(0x10ec0889, "ALC889", patch_alc882),
 	HDA_CODEC_ENTRY(0x10ec0892, "ALC892", patch_alc662),
+	HDA_CODEC_ENTRY(0x10ec0897, "ALC897", patch_alc662),
 	HDA_CODEC_ENTRY(0x10ec0899, "ALC898", patch_alc882),
 	HDA_CODEC_ENTRY(0x10ec0900, "ALC1150", patch_alc882),
 	HDA_CODEC_ENTRY(0x10ec0b00, "ALCS1200A", patch_alc882),

From: Takashi Iwai <[email protected]>

commit 242d990c158d5b1dabd166516e21992baef5f26a upstream.

The generic parser accepts the preferred_dacs[] pairs as a hint for assigning a DAC to each pin, but this hint doesn't work always effectively. Currently it's merely a secondary choice after the trial with the path index failed. This made sometimes it difficult to assign DACs without mimicking the connection list and/or the badness table.

This patch adds a new flag, obey_preferred_dacs, that changes the behavior of the parser. As its name stands, the parser obeys the given preferred_dacs[] pairs by skipping the path index matching and giving a high penalty if no DAC is assigned by the pairs. This mode will help for assigning the fixed DACs forcibly from the codec driver.

---
 sound/pci/hda/hda_generic.c |   12 ++++++++----
 sound/pci/hda/hda_generic.h |    1 +
 2 files changed, 9 insertions(+), 4 deletions(-)

@@ -1376,16 +1376,20 @@ static int try_assign_dacs(struct hda_co
 		struct nid_path *path;
 		hda_nid_t pin = pins[i];
 
-		path = snd_hda_get_path_from_idx(codec, path_idx[i]);
-		if (path) {
-			badness += assign_out_path_ctls(codec, path);
-			continue;
+		if (!spec->obey_preferred_dacs) {
+			path = snd_hda_get_path_from_idx(codec, path_idx[i]);
+			if (path) {
+				badness += assign_out_path_ctls(codec, path);
+				continue;
+			}
 		}
 
 		dacs[i] = get_preferred_dac(codec, pin);
 		if (dacs[i]) {
 			if (is_dac_already_used(codec, dacs[i]))
 				badness += bad->shared_primary;
+		} else if (spec->obey_preferred_dacs) {
+			badness += BAD_NO_PRIMARY_DAC;
 		}
 
 		if (!dacs[i])

@@ -240,6 +240,7 @@ struct hda_gen_spec {
 	unsigned int power_down_unused:1; /* power down unused widgets */
 	unsigned int dac_min_mute:1; /* minimal = mute for DACs */
 	unsigned int suppress_vmaster:1; /* don't create vmaster kctls */
+	unsigned int obey_preferred_dacs:1; /* obey preferred_dacs assignment */
 
 	/* other internal flags */
 	unsigned int no_analog:1; /* digital I/O only */

Hi!

Option added is never used as variable is never set. We don't need this in 4.19.

Best regards,
Pavel

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

Right, it seems that the succeeding fix is queued only for 5.4 and 5.9.

OTOH, this change will help if another quirk is added in near future, and it's pretty safe to apply, so I think it's worth to keep it.

thanks,

Takashi

Hi!

I agree that this is safe to apply and makes sense if we get another quirk soon. OTOH it is trivial to backport if it is needed.

Best regards,

Pavel

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

It's trivial to backport, but it's not trivial to let stable maintainers to inform beforehand if the next patch has CC-to-stable tag. Keeping this makes the backport easier, that's the point.

thanks,

Takashi

From: Naveen N. Rao <[email protected]>

commit 4c75b0ff4e4bf7a45b5aef9639799719c28d0073 upstream.

On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in ftrace_get_addr_new() followed by the below message:
Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001)

The set of steps leading to this involved:
- modprobe ftrace-direct-too
- enable_probe
- modprobe ftrace-direct
- rmmod ftrace-direct <-- trigger

The problem turned out to be that we were not updating flags in the ftrace record properly. From the above message about the trampoline accounting being bad, it can be seen that the ftrace record still has FTRACE_FL_TRAMP set though ftrace-direct module is going away. This happens because we are checking if any ftrace_ops has the FTRACE_FL_TRAMP flag set _before_ updating the filter hash.

The fix for this is to look for any _other_ ftrace_ops that also needs FTRACE_FL_TRAMP.

---
 kernel/trace/ftrace.c |   22 +++++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

@@ -1650,6 +1650,8 @@ static bool test_rec_ops_needs_regs(stru
 static struct ftrace_ops *
 ftrace_find_tramp_ops_any(struct dyn_ftrace *rec);
 static struct ftrace_ops *
+ftrace_find_tramp_ops_any_other(struct dyn_ftrace *rec, struct ftrace_ops *op_exclude);
+static struct ftrace_ops *
 ftrace_find_tramp_ops_next(struct dyn_ftrace *rec, struct ftrace_ops *ops);
 
 static bool __ftrace_hash_rec_update(struct ftrace_ops *ops,

@@ -1787,7 +1789,7 @@ static bool __ftrace_hash_rec_update(str
 			 * to it.
 			 */
 			if (ftrace_rec_count(rec) == 1 &&
-			    ftrace_find_tramp_ops_any(rec))
+			    ftrace_find_tramp_ops_any_other(rec, ops))
 				rec->flags |= FTRACE_FL_TRAMP;
 			else
 				rec->flags &= ~FTRACE_FL_TRAMP;

@@ -2209,6 +2211,24 @@ ftrace_find_tramp_ops_any(struct dyn_ftr
 			continue;
 
 		if (hash_contains_ip(ip, op->func_hash))
+			return op;
+	} while_for_each_ftrace_op(op);
+
+	return NULL;
+}
+
+static struct ftrace_ops *
+ftrace_find_tramp_ops_any_other(struct dyn_ftrace *rec, struct ftrace_ops *op_exclude)
+{
+	struct ftrace_ops *op;
+	unsigned long ip = rec->ip;
+
+	do_for_each_ftrace_op(op, ftrace_ops_list) {
+
+		if (op == op_exclude || !op->trampoline)
+			continue;
+
+		if (hash_contains_ip(ip, op->func_hash))
 			return op;
 	} while_for_each_ftrace_op(op);
 

From: Paulo Alcantara <[email protected]>

commit 212253367dc7b49ed3fc194ce71b0992eacaecf2 upstream.

This patch fixes a potential use-after-free bug in cifs_echo_request().

For instance,

thread 1
--------
cifs_demultiplex_thread()
clean_demultiplex_info()
kfree(server)

thread 2 (workqueue)
--------
apic_timer_interrupt()

    smp_apic_timer_interrupt()
      irq_exit()
        __do_softirq()
          run_timer_softirq()
            call_timer_fn()
	      cifs_echo_request() <- use-after-free in server ptr

---
 fs/cifs/connect.c |    2 ++
 1 file changed, 2 insertions(+)

@@ -777,6 +777,8 @@ static void clean_demultiplex_info(struc
 	list_del_init(&server->tcp_ses_list);
 	spin_unlock(&cifs_tcp_ses_lock);
 
+	cancel_delayed_work_sync(&server->echo);
+
 	spin_lock(&GlobalMid_Lock);
 	server->tcpStatus = CifsExiting;
 	spin_unlock(&GlobalMid_Lock);

From: Christian Eggers <[email protected]>

commit 61e6fe59ede155881a622f5901551b1cc8748f6a upstream.

If arbitration is lost, the master automatically changes to slave mode. I2SR_IBB may or may not be reset by hardware. Raising a STOP condition by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.

So calling i2c_imx_bus_busy() is not required and would busy-wait until timeout.

Tested (not extensively) on Vybrid VF500 (Toradex VF50):

                           # the 3rd argument from the calls to
                           # i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

---
 drivers/i2c/busses/i2c-imx.c |   12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

@@ -557,6 +557,8 @@ static void i2c_imx_stop(struct imx_i2c_
 		/* Stop I2C transaction */
 		dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
 		temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
+		if (!(temp & I2CR_MSTA))
+			i2c_imx->stopped = 1;
 		temp &= ~(I2CR_MSTA | I2CR_MTX);
 		if (i2c_imx->dma)
 			temp &= ~I2CR_DMAEN;

@@ -722,9 +724,12 @@ static int i2c_imx_dma_read(struct imx_i
 		 */
 		dev_dbg(dev, "<%s> clear MSTA\n", __func__);
 		temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
+		if (!(temp & I2CR_MSTA))
+			i2c_imx->stopped = 1;
 		temp &= ~(I2CR_MSTA | I2CR_MTX);
 		imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
-		i2c_imx_bus_busy(i2c_imx, 0);
+		if (!i2c_imx->stopped)
+			i2c_imx_bus_busy(i2c_imx, 0);
 	} else {
 		/*
 		 * For i2c master receiver repeat restart operation like:

@@ -847,9 +852,12 @@ static int i2c_imx_read(struct imx_i2c_s
 				dev_dbg(&i2c_imx->adapter.dev,
 					"<%s> clear MSTA\n", __func__);
 				temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
+				if (!(temp & I2CR_MSTA))
+					i2c_imx->stopped =  1;
 				temp &= ~(I2CR_MSTA | I2CR_MTX);
 				imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
-				i2c_imx_bus_busy(i2c_imx, 0);
+				if (!i2c_imx->stopped)
+					i2c_imx_bus_busy(i2c_imx, 0);
 			} else {
 				/*
 				 * For i2c master receiver repeat restart operation like:

From: Suganath Prabu S <[email protected]>

commit 42f687038bcc34aa919e0e4c29b04e4cda3f6a79 upstream.

Commit c1a6c5ac4278 ("scsi: mpt3sas: For NVME device, issue a protocol level reset") modified the ioctl path 'timeout' variable type to u8 from unsigned long, limiting the maximum timeout value that the driver can support to 255 seconds.

If the management application is requesting a higher value the resulting timeout will be zero. The operation times out immediately and the ioctl request fails.

Change datatype back to unsigned long.

---
 drivers/scsi/mpt3sas/mpt3sas_ctl.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -654,7 +654,7 @@ _ctl_do_mpt_command(struct MPT3SAS_ADAPT
 	struct _pcie_device *pcie_device = NULL;
 	u32 ioc_state;
 	u16 smid;
-	u8 timeout;
+	unsigned long timeout;
 	u8 issue_reset;
 	u32 sz, sz_arg;
 	void *psge;

From: Mikulas Patocka <[email protected]>

commit 67aa3ec3dbc43d6e34401d9b2a40040ff7bb57af upstream.

Advance the maximum number of arguments to 16.
This fixes issue where certain operations, combined with table configured args, exceed 10 arguments.

---
 drivers/md/dm-writecache.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -1883,7 +1883,7 @@ static int writecache_ctr(struct dm_targ
 	struct wc_memory_superblock s;
 
 	static struct dm_arg _args[] = {
-		{0, 10, "Invalid number of feature args"},
+		{0, 16, "Invalid number of feature args"},
 	};
 
 	as.argc = argc;

From: Mike Snitzer <[email protected]>

commit bde3808bc8c2741ad3d804f84720409aee0c2972 upstream.

Fixes sparse warnings:
drivers/md/dm.c:508:12: warning: context imbalance in 'dm_prepare_ioctl' - wrong count at exit drivers/md/dm.c:543:13: warning: context imbalance in 'dm_unprepare_ioctl' - wrong count at exit

---
 drivers/md/dm.c |    2 --
 1 file changed, 2 deletions(-)

@@ -462,7 +462,6 @@ static int dm_blk_getgeo(struct block_de
 
 static int dm_prepare_ioctl(struct mapped_device *md, int *srcu_idx,
 			    struct block_device **bdev)
-	__acquires(md->io_barrier)
 {
 	struct dm_target *tgt;
 	struct dm_table *map;

@@ -496,7 +495,6 @@ retry:
 }
 
 static void dm_unprepare_ioctl(struct mapped_device *md, int srcu_idx)
-	__releases(md->io_barrier)
 {
 	dm_put_live_table(md, srcu_idx);
 }

From: Yang Shi <[email protected]>

commit 8199be001a470209f5c938570cc199abb012fe53 upstream.

When investigating a slab cache bloat problem, significant amount of negative dentry cache was seen, but confusingly they neither got shrunk by reclaimer (the host has very tight memory) nor be shrunk by dropping cache. The vmcore shows there are over 14M negative dentry objects on lru, but tracing result shows they were even not scanned at all.

Further investigation shows the memcg's vfs shrinker_map bit is not set. So the reclaimer or dropping cache just skip calling vfs shrinker. So we have to reboot the hosts to get the memory back.

I didn't manage to come up with a reproducer in test environment, and the problem can't be reproduced after rebooting. But it seems there is race between shrinker map bit clear and reparenting by code inspection. The hypothesis is elaborated as below.

The memcg hierarchy on our production environment looks like:

                root
               /    \
          system   user

The main workloads are running under user slice's children, and it creates and removes memcg frequently. So reparenting happens very often under user slice, but no task is under user slice directly.

So with the frequent reparenting and tight memory pressure, the below hypothetical race condition may happen:

CPU A CPU B
reparent

    dst->nr_items == 0
                                 shrinker:
                                     total_objects == 0
    add src->nr_items to dst
    set_bit
                                     return SHRINK_EMPTY
                                     clear_bit

child memcg offline
replace child's kmemcg_id with
parent's (in memcg_offline_kmem())
list_lru_del() between shrinker runs
see parent's kmemcg_id dec dst->nr_items
reparent again
dst->nr_items may go negative
due to concurrent list_lru_del()

The second run of shrinker:
read nr_items without any synchronization, so it may see intermediate negative nr_items then total_objects may return 0 coincidently

keep the bit cleared
dst->nr_items != 0
skip set_bit
add scr->nr_item to dst

After this point dst->nr_item may never go zero, so reparenting will not set shrinker_map bit anymore. And since there is no task under user slice directly, so no new object will be added to its lru to set the shrinker map bit either. That bit is kept cleared forever.

How does list_lru_del() race with reparenting? It is because reparenting replaces children's kmemcg_id to parent's without protecting from nlru->lock, so list_lru_del() may see parent's kmemcg_id but actually deleting items from child's lru, but dec'ing parent's nr_items, so the parent's nr_items may go negative as commit 2788cf0c401c ("memcg:
reparent list_lrus and free kmemcg_id on css offline") says.

Since it is impossible that dst->nr_items goes negative and src->nr_items goes zero at the same time, so it seems we could set the shrinker map bit iff src->nr_items != 0. We could synchronize list_lru_count_one() and reparenting with nlru->lock, but it seems checking src->nr_items in reparenting is the simplest and avoids lock contention.

---
 mm/list_lru.c |   10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

@@ -542,7 +542,6 @@ static void memcg_drain_list_lru_node(st
 	struct list_lru_node *nlru = &lru->node[nid];
 	int dst_idx = dst_memcg->kmemcg_id;
 	struct list_lru_one *src, *dst;
-	bool set;
 
 	/*
 	 * Since list_lru_{add,del} may be called under an IRQ-safe lock,

@@ -554,11 +553,12 @@ static void memcg_drain_list_lru_node(st
 	dst = list_lru_from_memcg_idx(nlru, dst_idx);
 
 	list_splice_init(&src->list, &dst->list);
-	set = (!dst->nr_items && src->nr_items);
-	dst->nr_items += src->nr_items;
-	if (set)
+
+	if (src->nr_items) {
+		dst->nr_items += src->nr_items;
 		memcg_set_shrinker_bit(dst_memcg, nid, lru_shrinker_id(lru));
-	src->nr_items = 0;
+		src->nr_items = 0;
+	}
 
 	spin_unlock_irq(&nlru->lock);
 }

From: Qian Cai <[email protected]>

commit b11a76b37a5aa7b07c3e3eeeaae20b25475bddd3 upstream.

We can't call kvfree() with a spin lock held, so defer it. Fixes a might_sleep() runtime warning.

---
 mm/swapfile.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

@@ -2825,6 +2825,7 @@ late_initcall(max_swapfiles_check);
 static struct swap_info_struct *alloc_swap_info(void)
 {
 	struct swap_info_struct *p;
+	struct swap_info_struct *defer = NULL;
 	unsigned int type;
 	int i;
 	int size = sizeof(*p) + nr_node_ids * sizeof(struct plist_node);

@@ -2854,7 +2855,7 @@ static struct swap_info_struct *alloc_sw
 		smp_wmb();
 		WRITE_ONCE(nr_swapfiles, nr_swapfiles + 1);
 	} else {
-		kvfree(p);
+		defer = p;
 		p = swap_info[type];
 		/*
 		 * Do not memset this entry: a racing procfs swap_next()

@@ -2867,6 +2868,7 @@ static struct swap_info_struct *alloc_sw
 		plist_node_init(&p->avail_lists[i], 0);
 	p->flags = SWP_USED;
 	spin_unlock(&swap_lock);
+	kvfree(defer);
 	spin_lock_init(&p->lock);
 	spin_lock_init(&p->cont_lock);
 

From: Masami Hiramatsu <[email protected]>

commit 4e9a5ae8df5b3365183150f6df49e49dece80d8c upstream.

Since insn.prefixes.nbytes can be bigger than the size of insn.prefixes.bytes[] when a prefix is repeated, the proper check must be

insn.prefixes.bytes[i] != 0 and i < 4

instead of using insn.prefixes.nbytes.

Introduce a for_each_insn_prefix() macro for this purpose. Debugged by Kees Cook <[email protected]>.

[ bp: Massage commit message, sync with the respective header in tools/
and drop "we". ]

---
 arch/x86/include/asm/insn.h               |   15 +++++++++++++++
 arch/x86/kernel/uprobes.c                 |   10 ++++++----
 tools/objtool/arch/x86/include/asm/insn.h |   15 +++++++++++++++
 tools/perf/util/intel-pt-decoder/insn.h   |   15 +++++++++++++++
 4 files changed, 51 insertions(+), 4 deletions(-)

@@ -208,6 +208,21 @@ static inline int insn_offset_immediate(
 	return insn_offset_displacement(insn) + insn->displacement.nbytes;
 }
 
+/**
+ * for_each_insn_prefix() -- Iterate prefixes in the instruction
+ * @insn: Pointer to struct insn.
+ * @idx:  Index storage.
+ * @prefix: Prefix byte.
+ *
+ * Iterate prefix bytes of given @insn. Each prefix byte is stored in @prefix
+ * and the index is stored in @idx (note that this @idx is just for a cursor,
+ * do not change it.)
+ * Since prefixes.nbytes can be bigger than 4 if some prefixes
+ * are repeated, it cannot be used for looping over the prefixes.
+ */
+#define for_each_insn_prefix(insn, idx, prefix)	\
+	for (idx = 0; idx < ARRAY_SIZE(insn->prefixes.bytes) && (prefix = insn->prefixes.bytes[idx]) != 0; idx++)
+
 #define POP_SS_OPCODE 0x1f
 #define MOV_SREG_OPCODE 0x8e
 

@@ -268,12 +268,13 @@ static volatile u32 good_2byte_insns[256
 
 static bool is_prefix_bad(struct insn *insn)
 {
+	insn_byte_t p;
 	int i;
 
-	for (i = 0; i < insn->prefixes.nbytes; i++) {
+	for_each_insn_prefix(insn, i, p) {
 		insn_attr_t attr;
 
-		attr = inat_get_opcode_attribute(insn->prefixes.bytes[i]);
+		attr = inat_get_opcode_attribute(p);
 		switch (attr) {
 		case INAT_MAKE_PREFIX(INAT_PFX_ES):
 		case INAT_MAKE_PREFIX(INAT_PFX_CS):

@@ -728,6 +729,7 @@ static const struct uprobe_xol_ops push_
 static int branch_setup_xol_ops(struct arch_uprobe *auprobe, struct insn *insn)
 {
 	u8 opc1 = OPCODE1(insn);
+	insn_byte_t p;
 	int i;
 
 	switch (opc1) {

@@ -758,8 +760,8 @@ static int branch_setup_xol_ops(struct a
 	 * Intel and AMD behavior differ in 64-bit mode: Intel ignores 66 prefix.
 	 * No one uses these insns, reject any branch insns with such prefix.
 	 */
-	for (i = 0; i < insn->prefixes.nbytes; i++) {
-		if (insn->prefixes.bytes[i] == 0x66)
+	for_each_insn_prefix(insn, i, p) {
+		if (p == 0x66)
 			return -ENOTSUPP;
 	}
 

@@ -208,6 +208,21 @@ static inline int insn_offset_immediate(
 	return insn_offset_displacement(insn) + insn->displacement.nbytes;
 }
 
+/**
+ * for_each_insn_prefix() -- Iterate prefixes in the instruction
+ * @insn: Pointer to struct insn.
+ * @idx:  Index storage.
+ * @prefix: Prefix byte.
+ *
+ * Iterate prefix bytes of given @insn. Each prefix byte is stored in @prefix
+ * and the index is stored in @idx (note that this @idx is just for a cursor,
+ * do not change it.)
+ * Since prefixes.nbytes can be bigger than 4 if some prefixes
+ * are repeated, it cannot be used for looping over the prefixes.
+ */
+#define for_each_insn_prefix(insn, idx, prefix)	\
+	for (idx = 0; idx < ARRAY_SIZE(insn->prefixes.bytes) && (prefix = insn->prefixes.bytes[idx]) != 0; idx++)
+
 #define POP_SS_OPCODE 0x1f
 #define MOV_SREG_OPCODE 0x8e
 

@@ -208,6 +208,21 @@ static inline int insn_offset_immediate(
 	return insn_offset_displacement(insn) + insn->displacement.nbytes;
 }
 
+/**
+ * for_each_insn_prefix() -- Iterate prefixes in the instruction
+ * @insn: Pointer to struct insn.
+ * @idx:  Index storage.
+ * @prefix: Prefix byte.
+ *
+ * Iterate prefix bytes of given @insn. Each prefix byte is stored in @prefix
+ * and the index is stored in @idx (note that this @idx is just for a cursor,
+ * do not change it.)
+ * Since prefixes.nbytes can be bigger than 4 if some prefixes
+ * are repeated, it cannot be used for looping over the prefixes.
+ */
+#define for_each_insn_prefix(insn, idx, prefix)	\
+	for (idx = 0; idx < ARRAY_SIZE(insn->prefixes.bytes) && (prefix = insn->prefixes.bytes[idx]) != 0; idx++)
+
 #define POP_SS_OPCODE 0x1f
 #define MOV_SREG_OPCODE 0x8e
 

From: Christian Eggers <[email protected]>

commit 384a9565f70a876c2e78e58c5ca0bbf0547e4f6d upstream.

According to the "VFxxx Controller Reference Manual" (and the comment block starting at line 97), Vybrid requires writing a one for clearing an interrupt flag. Syncing the method for clearing I2SR_IIF in i2c_imx_isr().

---
 drivers/i2c/busses/i2c-imx.c |   20 +++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

@@ -404,6 +404,19 @@ static void i2c_imx_dma_free(struct imx_
 	dma->chan_using = NULL;
 }
 
+static void i2c_imx_clear_irq(struct imx_i2c_struct *i2c_imx, unsigned int bits)
+{
+	unsigned int temp;
+
+	/*
+	 * i2sr_clr_opcode is the value to clear all interrupts. Here we want to
+	 * clear only <bits>, so we write ~i2sr_clr_opcode with just <bits>
+	 * toggled. This is required because i.MX needs W0C and Vybrid uses W1C.
+	 */
+	temp = ~i2c_imx->hwdata->i2sr_clr_opcode ^ bits;
+	imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2SR);
+}
+
 static int i2c_imx_bus_busy(struct imx_i2c_struct *i2c_imx, int for_busy)
 {
 	unsigned long orig_jiffies = jiffies;

@@ -416,8 +429,7 @@ static int i2c_imx_bus_busy(struct imx_i
 
 		/* check for arbitration lost */
 		if (temp & I2SR_IAL) {
-			temp &= ~I2SR_IAL;
-			imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2SR);
+			i2c_imx_clear_irq(i2c_imx, I2SR_IAL);
 			return -EAGAIN;
 		}
 

@@ -589,9 +601,7 @@ static irqreturn_t i2c_imx_isr(int irq,
 	if (temp & I2SR_IIF) {
 		/* save status register */
 		i2c_imx->i2csr = temp;
-		temp &= ~I2SR_IIF;
-		temp |= (i2c_imx->hwdata->i2sr_clr_opcode & I2SR_IIF);
-		imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2SR);
+		i2c_imx_clear_irq(i2c_imx, I2SR_IIF);
 		wake_up(&i2c_imx->queue);
 		return IRQ_HANDLED;
 	}

From: Christian Eggers <[email protected]>

commit 1de67a3dee7a279ebe4d892b359fe3696938ec15 upstream.

Arbitration Lost (IAL) can happen after every single byte transfer. If arbitration is lost, the I2C hardware will autonomously switch from master mode to slave. If a transfer is not aborted in this state, consecutive transfers will not be executed by the hardware and will timeout.

Tested (not extensively) on Vybrid VF500 (Toradex VF50):

---
 drivers/i2c/busses/i2c-imx.c |   10 ++++++++++
 1 file changed, 10 insertions(+)

@@ -460,6 +460,16 @@ static int i2c_imx_trx_complete(struct i
 		dev_dbg(&i2c_imx->adapter.dev, "<%s> Timeout\n", __func__);
 		return -ETIMEDOUT;
 	}
+
+	/* check for arbitration lost */
+	if (i2c_imx->i2csr & I2SR_IAL) {
+		dev_dbg(&i2c_imx->adapter.dev, "<%s> Arbitration lost\n", __func__);
+		i2c_imx_clear_irq(i2c_imx, I2SR_IAL);
+
+		i2c_imx->i2csr = 0;
+		return -EAGAIN;
+	}
+
 	dev_dbg(&i2c_imx->adapter.dev, "<%s> TRX complete\n", __func__);
 	i2c_imx->i2csr = 0;
 	return 0;

From: Samuel Thibault <[email protected]>

commit f0992098cadb4c9c6a00703b66cafe604e178fea upstream.

Speakup exposing a line discipline allows userland to try to use it, while it is deemed to be useless, and thus uselessly exposes potential bugs. One of them is simply that in such a case if the line sends data, spk_ttyio_receive_buf2 is called and crashes since spk_ttyio_synth is NULL.

This change restricts the use of the speakup line discipline to speakup drivers, thus avoiding such kind of issues altogether.

---
 drivers/staging/speakup/spk_ttyio.c |   37 ++++++++++++++++++++++--------------
 1 file changed, 23 insertions(+), 14 deletions(-)

@@ -47,27 +47,20 @@ static int spk_ttyio_ldisc_open(struct t
 {
 	struct spk_ldisc_data *ldisc_data;
 
+	if (tty != speakup_tty)
+		/* Somebody tried to use this line discipline outside speakup */
+		return -ENODEV;
+
 	if (tty->ops->write == NULL)
 		return -EOPNOTSUPP;
 
-	mutex_lock(&speakup_tty_mutex);
-	if (speakup_tty) {
-		mutex_unlock(&speakup_tty_mutex);
-		return -EBUSY;
-	}
-	speakup_tty = tty;
-
 	ldisc_data = kmalloc(sizeof(struct spk_ldisc_data), GFP_KERNEL);
-	if (!ldisc_data) {
-		speakup_tty = NULL;
-		mutex_unlock(&speakup_tty_mutex);
+	if (!ldisc_data)
 		return -ENOMEM;
-	}
 
 	sema_init(&ldisc_data->sem, 0);
 	ldisc_data->buf_free = true;
-	speakup_tty->disc_data = ldisc_data;
-	mutex_unlock(&speakup_tty_mutex);
+	tty->disc_data = ldisc_data;
 
 	return 0;
 }

@@ -187,9 +180,25 @@ static int spk_ttyio_initialise_ldisc(st
 
 	tty_unlock(tty);
 
+	mutex_lock(&speakup_tty_mutex);
+	speakup_tty = tty;
 	ret = tty_set_ldisc(tty, N_SPEAKUP);
 	if (ret)
-		pr_err("speakup: Failed to set N_SPEAKUP on tty\n");
+		speakup_tty = NULL;
+	mutex_unlock(&speakup_tty_mutex);
+
+	if (!ret)
+		/* Success */
+		return 0;
+
+	pr_err("speakup: Failed to set N_SPEAKUP on tty\n");
+
+	tty_lock(tty);
+	if (tty->ops->close)
+		tty->ops->close(tty, NULL);
+	tty_unlock(tty);
+
+	tty_kclose(tty);
 
 	return ret;
 }

From: Suravee Suthikulpanit <[email protected]>

commit 4165bf015ba9454f45beaad621d16c516d5c5afe upstream.

According to the AMD IOMMU spec, the commit 73db2fc595f3 ("iommu/amd: Increase interrupt remapping table limit to 512 entries") also requires the interrupt table length (IntTabLen) to be set to 9 (power of 2) in the device table mapping entry (DTE).

---
 drivers/iommu/amd_iommu_types.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -259,7 +259,7 @@
 #define DTE_IRQ_REMAP_INTCTL_MASK	(0x3ULL << 60)
 #define DTE_IRQ_TABLE_LEN_MASK	(0xfULL << 1)
 #define DTE_IRQ_REMAP_INTCTL    (2ULL << 60)
-#define DTE_IRQ_TABLE_LEN       (8ULL << 1)
+#define DTE_IRQ_TABLE_LEN       (9ULL << 1)
 #define DTE_IRQ_REMAP_ENABLE    1ULL
 
 #define PAGE_MODE_NONE    0x00

From: Lukas Wunner <[email protected]>

[ Upstream commit 5e844cc37a5cbaa460e68f9a989d321d63088a89 ]

SPI driver probing currently comprises two steps, whereas removal comprises only one step:

spi_alloc_master()
spi_register_controller()

spi_unregister_controller()

That's because spi_unregister_controller() calls device_unregister() instead of device_del(), thereby releasing the reference on the spi_controller which was obtained by spi_alloc_master().

An SPI driver's private data is contained in the same memory allocation as the spi_controller struct. Thus, once spi_unregister_controller() has been called, the private data is inaccessible. But some drivers need to access it after spi_unregister_controller() to perform further teardown steps.

Introduce devm_spi_alloc_master() and devm_spi_alloc_slave(), which release a reference on the spi_controller struct only after the driver has unbound, thereby keeping the memory allocation accessible. Change spi_unregister_controller() to not release a reference if the spi_controller was allocated by one of these new devm functions.

The present commit is small enough to be backportable to stable. It allows fixing drivers which use the private data in their ->remove() hook after it's been freed. It also allows fixing drivers which neglect to release a reference on the spi_controller in the probe error path.

Long-term, most SPI drivers shall be moved over to the devm functions introduced herein. The few that can't shall be changed in a treewide commit to explicitly release the last reference on the controller. That commit shall amend spi_unregister_controller() to no longer release a reference, thereby completing the migration.

As a result, the behaviour will be less surprising and more consistent with subsystems such as IIO, which also includes the private data in the allocation of the generic iio_dev struct, but calls device_del() in iio_device_unregister().

---
 drivers/spi/spi.c       |   58 +++++++++++++++++++++++++++++++++++++++++++++++-
 include/linux/spi/spi.h |   19 +++++++++++++++
 2 files changed, 76 insertions(+), 1 deletion(-)

@@ -2050,6 +2050,49 @@ struct spi_controller *__spi_alloc_contr
 }
 EXPORT_SYMBOL_GPL(__spi_alloc_controller);
 
+static void devm_spi_release_controller(struct device *dev, void *ctlr)
+{
+	spi_controller_put(*(struct spi_controller **)ctlr);
+}
+
+/**
+ * __devm_spi_alloc_controller - resource-managed __spi_alloc_controller()
+ * @dev: physical device of SPI controller
+ * @size: how much zeroed driver-private data to allocate
+ * @slave: whether to allocate an SPI master (false) or SPI slave (true)
+ * Context: can sleep
+ *
+ * Allocate an SPI controller and automatically release a reference on it
+ * when @dev is unbound from its driver.  Drivers are thus relieved from
+ * having to call spi_controller_put().
+ *
+ * The arguments to this function are identical to __spi_alloc_controller().
+ *
+ * Return: the SPI controller structure on success, else NULL.
+ */
+struct spi_controller *__devm_spi_alloc_controller(struct device *dev,
+						   unsigned int size,
+						   bool slave)
+{
+	struct spi_controller **ptr, *ctlr;
+
+	ptr = devres_alloc(devm_spi_release_controller, sizeof(*ptr),
+			   GFP_KERNEL);
+	if (!ptr)
+		return NULL;
+
+	ctlr = __spi_alloc_controller(dev, size, slave);
+	if (ctlr) {
+		*ptr = ctlr;
+		devres_add(dev, ptr);
+	} else {
+		devres_free(ptr);
+	}
+
+	return ctlr;
+}
+EXPORT_SYMBOL_GPL(__devm_spi_alloc_controller);
+
 #ifdef CONFIG_OF
 static int of_spi_register_master(struct spi_controller *ctlr)
 {

@@ -2300,6 +2343,11 @@ int devm_spi_register_controller(struct
 }
 EXPORT_SYMBOL_GPL(devm_spi_register_controller);
 
+static int devm_spi_match_controller(struct device *dev, void *res, void *ctlr)
+{
+	return *(struct spi_controller **)res == ctlr;
+}
+
 static int __unregister(struct device *dev, void *null)
 {
 	spi_unregister_device(to_spi_device(dev));

@@ -2341,7 +2389,15 @@ void spi_unregister_controller(struct sp
 	list_del(&ctlr->list);
 	mutex_unlock(&board_lock);
 
-	device_unregister(&ctlr->dev);
+	device_del(&ctlr->dev);
+
+	/* Release the last reference on the controller if its driver
+	 * has not yet been converted to devm_spi_alloc_master/slave().
+	 */
+	if (!devres_find(ctlr->dev.parent, devm_spi_release_controller,
+			 devm_spi_match_controller, ctlr))
+		put_device(&ctlr->dev);
+
 	/* free bus id */
 	mutex_lock(&board_lock);
 	if (found == ctlr)

@@ -634,6 +634,25 @@ static inline struct spi_controller *spi
 	return __spi_alloc_controller(host, size, true);
 }
 
+struct spi_controller *__devm_spi_alloc_controller(struct device *dev,
+						   unsigned int size,
+						   bool slave);
+
+static inline struct spi_controller *devm_spi_alloc_master(struct device *dev,
+							   unsigned int size)
+{
+	return __devm_spi_alloc_controller(dev, size, false);
+}
+
+static inline struct spi_controller *devm_spi_alloc_slave(struct device *dev,
+							  unsigned int size)
+{
+	if (!IS_ENABLED(CONFIG_SPI_SLAVE))
+		return NULL;
+
+	return __devm_spi_alloc_controller(dev, size, true);
+}
+
 extern int spi_register_controller(struct spi_controller *ctlr);
 extern int devm_spi_register_controller(struct device *dev,
 					struct spi_controller *ctlr);

From: Lukas Wunner <[email protected]>

commit 63c5395bb7a9777a33f0e7b5906f2c0170a23692 upstream

bcm_qspi_remove() calls spi_unregister_master() even though bcm_qspi_probe() calls devm_spi_register_master(). The spi_master is therefore unregistered and freed twice on unbind.

Moreover, since commit 0392727c261b ("spi: bcm-qspi: Handle clock probe deferral"), bcm_qspi_probe() leaks the spi_master allocation if the call to devm_clk_get_optional() fails.

Fix by switching over to the new devm_spi_alloc_master() helper which keeps the private data accessible until the driver has unbound and also avoids the spi_master leak on probe.

While at it, fix an ordering issue in bcm_qspi_remove() wherein spi_unregister_master() is called after uninitializing the hardware, disabling the clock and freeing an IRQ data structure. The correct order is to call spi_unregister_master() *before* those teardown steps because bus accesses may still be ongoing until that function returns.

---
 drivers/spi/spi-bcm-qspi.c |   34 ++++++++++++----------------------
 1 file changed, 12 insertions(+), 22 deletions(-)

@@ -1223,7 +1223,7 @@ int bcm_qspi_probe(struct platform_devic
 	if (!of_match_node(bcm_qspi_of_match, dev->of_node))
 		return -ENODEV;
 
-	master = spi_alloc_master(dev, sizeof(struct bcm_qspi));
+	master = devm_spi_alloc_master(dev, sizeof(struct bcm_qspi));
 	if (!master) {
 		dev_err(dev, "error allocating spi_master\n");
 		return -ENOMEM;

@@ -1257,21 +1257,17 @@ int bcm_qspi_probe(struct platform_devic
 
 	if (res) {
 		qspi->base[MSPI]  = devm_ioremap_resource(dev, res);
-		if (IS_ERR(qspi->base[MSPI])) {
-			ret = PTR_ERR(qspi->base[MSPI]);
-			goto qspi_resource_err;
-		}
+		if (IS_ERR(qspi->base[MSPI]))
+			return PTR_ERR(qspi->base[MSPI]);
 	} else {
-		goto qspi_resource_err;
+		return 0;
 	}
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "bspi");
 	if (res) {
 		qspi->base[BSPI]  = devm_ioremap_resource(dev, res);
-		if (IS_ERR(qspi->base[BSPI])) {
-			ret = PTR_ERR(qspi->base[BSPI]);
-			goto qspi_resource_err;
-		}
+		if (IS_ERR(qspi->base[BSPI]))
+			return PTR_ERR(qspi->base[BSPI]);
 		qspi->bspi_mode = true;
 	} else {
 		qspi->bspi_mode = false;

@@ -1282,18 +1278,14 @@ int bcm_qspi_probe(struct platform_devic
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "cs_reg");
 	if (res) {
 		qspi->base[CHIP_SELECT]  = devm_ioremap_resource(dev, res);
-		if (IS_ERR(qspi->base[CHIP_SELECT])) {
-			ret = PTR_ERR(qspi->base[CHIP_SELECT]);
-			goto qspi_resource_err;
-		}
+		if (IS_ERR(qspi->base[CHIP_SELECT]))
+			return PTR_ERR(qspi->base[CHIP_SELECT]);
 	}
 
 	qspi->dev_ids = kcalloc(num_irqs, sizeof(struct bcm_qspi_dev_id),
 				GFP_KERNEL);
-	if (!qspi->dev_ids) {
-		ret = -ENOMEM;
-		goto qspi_resource_err;
-	}
+	if (!qspi->dev_ids)
+		return -ENOMEM;
 
 	for (val = 0; val < num_irqs; val++) {
 		irq = -1;

@@ -1369,7 +1361,7 @@ int bcm_qspi_probe(struct platform_devic
 	qspi->xfer_mode.addrlen = -1;
 	qspi->xfer_mode.hp = -1;
 
-	ret = devm_spi_register_master(&pdev->dev, master);
+	ret = spi_register_master(master);
 	if (ret < 0) {
 		dev_err(dev, "can't register master\n");
 		goto qspi_reg_err;

@@ -1382,8 +1374,6 @@ qspi_reg_err:
 	clk_disable_unprepare(qspi->clk);
 qspi_probe_err:
 	kfree(qspi->dev_ids);
-qspi_resource_err:
-	spi_master_put(master);
 	return ret;
 }
 /* probe function to be called by SoC specific platform driver probe */

@@ -1393,10 +1383,10 @@ int bcm_qspi_remove(struct platform_devi
 {
 	struct bcm_qspi *qspi = platform_get_drvdata(pdev);
 
+	spi_unregister_master(qspi->master);
 	bcm_qspi_hw_uninit(qspi);
 	clk_disable_unprepare(qspi->clk);
 	kfree(qspi->dev_ids);
-	spi_unregister_master(qspi->master);
 
 	return 0;
 }

From: Lukas Wunner <[email protected]>

[ Upstream commit e1483ac030fb4c57734289742f1c1d38dca61e22 ]

bcm2835_spi_remove() accesses the driver's private data after calling spi_unregister_controller() even though that function releases the last reference on the spi_controller and thereby frees the private data.

Fix by switching over to the new devm_spi_alloc_master() helper which keeps the private data accessible until the driver has unbound.

---
 drivers/spi/spi-bcm2835.c |   15 +++++----------
 1 file changed, 5 insertions(+), 10 deletions(-)

@@ -737,7 +737,7 @@ static int bcm2835_spi_probe(struct plat
 	struct resource *res;
 	int err;
 
-	master = spi_alloc_master(&pdev->dev, sizeof(*bs));
+	master = devm_spi_alloc_master(&pdev->dev, sizeof(*bs));
 	if (!master) {
 		dev_err(&pdev->dev, "spi_alloc_master() failed\n");
 		return -ENOMEM;

@@ -759,23 +759,20 @@ static int bcm2835_spi_probe(struct plat
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	bs->regs = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(bs->regs)) {
-		err = PTR_ERR(bs->regs);
-		goto out_master_put;
-	}
+	if (IS_ERR(bs->regs))
+		return PTR_ERR(bs->regs);
 
 	bs->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(bs->clk)) {
 		err = PTR_ERR(bs->clk);
 		dev_err(&pdev->dev, "could not get clk: %d\n", err);
-		goto out_master_put;
+		return err;
 	}
 
 	bs->irq = platform_get_irq(pdev, 0);
 	if (bs->irq <= 0) {
 		dev_err(&pdev->dev, "could not get IRQ: %d\n", bs->irq);
-		err = bs->irq ? bs->irq : -ENODEV;
-		goto out_master_put;
+		return bs->irq ? bs->irq : -ENODEV;
 	}
 
 	clk_prepare_enable(bs->clk);

@@ -803,8 +800,6 @@ static int bcm2835_spi_probe(struct plat
 
 out_clk_disable:
 	clk_disable_unprepare(bs->clk);
-out_master_put:
-	spi_master_put(master);
 	return err;
 }
 

From: Peter Ujfalusi <[email protected]>

[ Upstream commit 666224b43b4bd4612ce3b758c038f9bc5c5e3fcb ]

The DMA channel was not released if either devm_request_irq() or devm_spi_register_controller() failed.

---
 drivers/spi/spi-bcm2835.c |    7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

@@ -787,18 +787,19 @@ static int bcm2835_spi_probe(struct plat
 			       dev_name(&pdev->dev), master);
 	if (err) {
 		dev_err(&pdev->dev, "could not request IRQ: %d\n", err);
-		goto out_clk_disable;
+		goto out_dma_release;
 	}
 
 	err = spi_register_master(master);
 	if (err) {
 		dev_err(&pdev->dev, "could not register SPI master: %d\n", err);
-		goto out_clk_disable;
+		goto out_dma_release;
 	}
 
 	return 0;
 
-out_clk_disable:
+out_dma_release:
+	bcm2835_dma_release(master);
 	clk_disable_unprepare(bs->clk);
 	return err;
 }

From: Steven Rostedt (VMware) <[email protected]>

commit bcee5278958802b40ee8b26679155a6d9231783e upstream.

When the instances were able to use their own options, the userstacktrace option was left hardcoded for the top level. This made the instance userstacktrace option bascially into a nop, and will confuse users that set it, but nothing happens (I was confused when it happened to me!)

---
 kernel/trace/trace.c |    7 ++++---
 kernel/trace/trace.h |    6 ++++--
 2 files changed, 8 insertions(+), 5 deletions(-)

@@ -2416,7 +2416,7 @@ void trace_buffer_unlock_commit_regs(str
 	 * two. They are not that meaningful.
 	 */
 	ftrace_trace_stack(tr, buffer, flags, regs ? 0 : STACK_SKIP, pc, regs);
-	ftrace_trace_userstack(buffer, flags, pc);
+	ftrace_trace_userstack(tr, buffer, flags, pc);
 }
 
 /*

@@ -2736,14 +2736,15 @@ void trace_dump_stack(int skip)
 static DEFINE_PER_CPU(int, user_stack_count);
 
 void
-ftrace_trace_userstack(struct ring_buffer *buffer, unsigned long flags, int pc)
+ftrace_trace_userstack(struct trace_array *tr,
+		       struct ring_buffer *buffer, unsigned long flags, int pc)
 {
 	struct trace_event_call *call = &event_user_stack;
 	struct ring_buffer_event *event;
 	struct userstack_entry *entry;
 	struct stack_trace trace;
 
-	if (!(global_trace.trace_flags & TRACE_ITER_USERSTACKTRACE))
+	if (!(tr->trace_flags & TRACE_ITER_USERSTACKTRACE))
 		return;
 
 	/*

@@ -745,13 +745,15 @@ void update_max_tr_single(struct trace_a
 #endif /* CONFIG_TRACER_MAX_TRACE */
 
 #ifdef CONFIG_STACKTRACE
-void ftrace_trace_userstack(struct ring_buffer *buffer, unsigned long flags,
+void ftrace_trace_userstack(struct trace_array *tr,
+			    struct ring_buffer *buffer, unsigned long flags,
 			    int pc);
 
 void __trace_stack(struct trace_array *tr, unsigned long flags, int skip,
 		   int pc);
 #else
-static inline void ftrace_trace_userstack(struct ring_buffer *buffer,
+static inline void ftrace_trace_userstack(struct trace_array *tr,
+					  struct ring_buffer *buffer,
 					  unsigned long flags, int pc)
 {
 }

From: Bob Peterson <[email protected]>

commit 778721510e84209f78e31e2ccb296ae36d623f5e upstream.

If gfs2 tries to mount a (corrupt) file system that has no resource groups it still tries to set preferences on the first one, which causes a kernel null pointer dereference. This patch adds a check to function gfs2_ri_update so this condition is detected and reported back as an error.

---
 fs/gfs2/rgrp.c |    4 ++++
 1 file changed, 4 insertions(+)

@@ -1009,6 +1009,10 @@ static int gfs2_ri_update(struct gfs2_in
 	if (error < 0)
 		return error;
 
+	if (RB_EMPTY_ROOT(&sdp->sd_rindex_tree)) {
+		fs_err(sdp, "no resource groups found in the file system.\n");
+		return -ENOENT;
+	}
 	set_rgrp_preferences(sdp);
 
 	sdp->sd_rindex_uptodate = 1;

From: Zhihao Cheng <[email protected]>

commit e9acf0298c664f825e6f1158f2a97341bf9e03ca upstream.

Fix to return the error code from qup_i2c_change_state() instaed of 0 in qup_i2c_bam_schedule_desc().

---
 drivers/i2c/busses/i2c-qup.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

@@ -806,7 +806,8 @@ static int qup_i2c_bam_schedule_desc(str
 	if (ret || qup->bus_err || qup->qup_err) {
 		reinit_completion(&qup->xfer);
 
-		if (qup_i2c_change_state(qup, QUP_RUN_STATE)) {
+		ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
+		if (ret) {
 			dev_err(qup->dev, "change to run state timed out");
 			goto desc_err;
 		}

From: Mike Snitzer <[email protected]>

commit 857c4c0a8b2888d806f4308c58f59a6a81a1dee9 upstream.

Building on arch/s390/ results in this build error:

cc1: some warnings being treated as errors
../drivers/md/dm-writecache.c: In function 'persistent_memory_claim':
../drivers/md/dm-writecache.c:323:1: error: no return statement in function returning non-void [-Werror=return-type]

Fix this by replacing the BUG() with an -EOPNOTSUPP return.

---
 drivers/md/dm-writecache.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -318,7 +318,7 @@ err1:
 #else
 static int persistent_memory_claim(struct dm_writecache *wc)
 {
-	BUG();
+	return -EOPNOTSUPP;
 }
 #endif
 

From: Luo Meng <[email protected]>

commit 855b69857830f8d918d715014f05e59a3f7491a0 upstream.

Fix to return a negative error code from the error handling case instead of 0 in function i8042_setup_aux(), as done elsewhere in this function.

---
 drivers/input/serio/i8042.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

@@ -1472,7 +1472,8 @@ static int __init i8042_setup_aux(void)
 	if (error)
 		goto err_free_ports;
 
-	if (aux_enable())
+	error = aux_enable();
+	if (error)
 		goto err_free_irq;
 
 	i8042_aux_irq_registered = true;

Hi!

I'd recommend not taking this. It is not known to fix end-user-visible-bug, i8042 is normally quite fragile, and the patch is less then month old so did not get adequate testing.

Yes, code looks cleaner after the fix. With i8042, that does not mean much.

Best regards,
Pavel

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

From: Florian Westphal <[email protected]>

commit c0700dfa2cae44c033ed97dade8a2679c7d22a9d upstream.

There are reports wrt lockdep splat in nftables, e.g.:

------------[ cut here ]------------
WARNING: CPU: 2 PID: 31416 at net/netfilter/nf_tables_api.c:622
lockdep_nfnl_nft_mutex_not_held+0x28/0x38 [nf_tables]

...

These are caused by an earlier, unrelated bug such as a n ABBA deadlock in a different subsystem.
In such an event, lockdep is disabled and lockdep_is_held returns true unconditionally. This then causes the WARN() in nf_tables.

Make the WARN conditional on lockdep still active to avoid this.

---
 net/netfilter/nf_tables_api.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

@@ -532,7 +532,8 @@ static void nft_request_module(struct ne
 static void lockdep_nfnl_nft_mutex_not_held(void)
 {
 #ifdef CONFIG_PROVE_LOCKING
-	WARN_ON_ONCE(lockdep_nfnl_is_held(NFNL_SUBSYS_NFTABLES));
+	if (debug_locks)
+		WARN_ON_ONCE(lockdep_nfnl_is_held(NFNL_SUBSYS_NFTABLES));
 #endif
 }
 

From: Masami Hiramatsu <[email protected]>

commit 12cb908a11b2544b5f53e9af856e6b6a90ed5533 upstream

Since insn.prefixes.nbytes can be bigger than the size of insn.prefixes.bytes[] when a prefix is repeated, the proper check must be

insn.prefixes.bytes[i] != 0 and i < 4

instead of using insn.prefixes.nbytes. Use the new for_each_insn_prefix() macro which does it correctly.

Debugged by Kees Cook <[email protected]>.

[ bp: Massage commit message. ]

---
 arch/x86/lib/insn-eval.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

@@ -70,14 +70,15 @@ static int get_seg_reg_override_idx(stru
 {
 	int idx = INAT_SEG_REG_DEFAULT;
 	int num_overrides = 0, i;
+	insn_byte_t p;
 
 	insn_get_prefixes(insn);
 
 	/* Look for any segment override prefixes. */
-	for (i = 0; i < insn->prefixes.nbytes; i++) {
+	for_each_insn_prefix(insn, i, p) {
 		insn_attr_t attr;
 
-		attr = inat_get_opcode_attribute(insn->prefixes.bytes[i]);
+		attr = inat_get_opcode_attribute(p);
 		switch (attr) {
 		case INAT_MAKE_PREFIX(INAT_PFX_CS):
 			idx = INAT_SEG_REG_CS;

All tests passing for Tegra ...

Test results for stable-v4.19:

    15 builds:	15 pass, 0 fail
    22 boots:	22 pass, 0 fail
    38 tests:	38 pass, 0 fail

Linux version: 4.19.163-rc1-ga1b1c60de6b9
Boards tested: tegra124-jetson-tk1, tegra186-p2771-0000,

                tegra194-p2972-0000, tegra20-ventana,
                tegra210-p2371-2180, tegra30-cardhu-a04

Jon

CIP testing did not find any problems here.

Best regards,
Pavel

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

Thanks for testing and letting me know.

greg k-h

Compiled and booted on my test system. No dmesg regressions.

thanks,
-- Shuah

Build results:

	total: 155 pass: 155 fail: 0
Qemu test results:
	total: 417 pass: 417 fail: 0

Guenter

Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.

Summary
------------------------------------------------------------------------

kernel: 4.19.163-rc1
git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
git branch: linux-4.19.y
git commit: a1b1c60de6b977bc1a2fc8176b647879030ab862
git describe: v4.19.162-41-ga1b1c60de6b9
Test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-linux-4.19.y/build/v4.19.162-41-ga1b1c60de6b9

No regressions (compared to build v4.19.162)

No fixes (compared to build v4.19.162)

Ran 43756 total tests in the following environments and test suites.

Environments
--------------
- arm
- arm64
- dragonboard-410c - arm64
- hi6220-hikey - arm64
- i386
- juno-r2 - arm64
- juno-r2-compat
- juno-r2-kasan
- mips
- nxp-ls2088
- qemu-arm64-clang
- qemu-arm64-kasan
- qemu-x86_64-clang
- qemu-x86_64-kasan
- qemu_arm
- qemu_arm64
- qemu_arm64-compat
- qemu_i386
- qemu_x86_64
- qemu_x86_64-compat
- s390
- sparc
- x15 - arm
- x86_64
- x86-kasan

Test Suites
-----------
* build
* linux-log-parser
* install-android-platform-tools-r2600
* libhugetlbfs
* ltp-controllers-tests
* ltp-cve-tests
* ltp-dio-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs_bind-tests
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-io-tests
* ltp-sched-tests
* kselftest
* ltp-cap_bounds-tests
* ltp-containers-tests
* ltp-cpuhotplug-tests
* ltp-crypto-tests
* ltp-ipc-tests
* ltp-mm-tests
* ltp-nptl-tests
* ltp-pty-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* ltp-tracing-tests
* network-basic-tests
* perf
* v4l2-compliance
* ltp-commands-tests
* ltp-fs-tests
* ltp-math-tests
* ltp-open-posix-tests
* kvm-unit-tests
* rcutorture
* fwts

Linaro LKFT
https://lkft.linaro.org