Skip to contentSkip to conversation

riscv: Add support for SPI on Kendryte K210

PATCH Superseded Sean Anderson 1 participant 1 message Dec 22, 2020

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 riscv: Add support for SPI on Kendryte K210

This enables configs necessary for using SPI. The environment is saved to the very end of SPI flash. This is unlikely to be overwritten unless the entire flash is reprogrammed.

This also supplies a default bootcommand. It loads an image and device tree from the first partition of the MMC. This is a minimal/least effort bootcmd, so suggestions (especially in the form of patches) are welcome. I didn't set up distro boot because I think it is unlikely that any general-purpose linux distros will ever be ported to this board.

---
Sorry for the late follow-up Jagen.

This patch was previously part of
https://patchwork.ozlabs.org/project/uboot/list/?series=208443

 board/sipeed/maix/Kconfig          |  16 ++
 configs/sipeed_maix_bitm_defconfig |  10 +
 doc/board/sipeed/maix.rst          | 319 ++++++++++++++++++++++++-----
 include/configs/sipeed-maix.h      |   7 +-
 4 files changed, 300 insertions(+), 52 deletions(-)
board/sipeed/maix/Kconfig +16 -0
index 4c42dd2087..2cdea8ea81 100644
@@ -53,4 +53,20 @@ config BOARD_SPECIFIC_OPTIONS
 	imply CMD_GPIO
 	imply LED
 	imply LED_GPIO
+	imply SPI
+	imply DESIGNWARE_SPI
+	imply SPI_FLASH_GIGADEVICE
+	imply SPI_FLASH_WINBOND
+	imply DM_MTD
+	imply SPI_FLASH_MTD
+	imply CMD_MTD
+	imply ENV_IS_IN_SPI_FLASH
+	imply MMC
+	imply MMC_BROKEN_CD
+	imply MMC_SPI
+	imply CMD_MMC
+	imply DOS_PARTITION
+	imply EFI_PARTITION
+	imply CMD_PART
+	imply CMD_FS_GENERIC
 endif
configs/sipeed_maix_bitm_defconfig +10 -0
index 459bf0d530..cb9824e84e 100644
@@ -1,8 +1,18 @@
 CONFIG_RISCV=y
+CONFIG_ENV_SIZE=0x1000
+CONFIG_ENV_OFFSET=0xfff000
+CONFIG_ENV_SECT_SIZE=0x1000
 CONFIG_TARGET_SIPEED_MAIX=y
 CONFIG_ARCH_RV64I=y
 CONFIG_STACK_SIZE=0x100000
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="run k210_bootcmd"
+CONFIG_MTDIDS_DEFAULT="nor0=spi3:0"
+CONFIG_MTDPARTS_DEFAULT="nor0:1M(u-boot),0x1000 at 0xfff000(env)"
 # CONFIG_NET is not set
 # CONFIG_INPUT is not set
+CONFIG_SF_DEFAULT_BUS=3
 # CONFIG_DM_ETH is not set
+CONFIG_FS_EXT4=y
+CONFIG_FS_FAT=y
 # CONFIG_EFI_LOADER is not set
doc/board/sipeed/maix.rst +269 -50

366 lines not on this page · raw message

include/configs/sipeed-maix.h +5 -2
index 36ff522e4b..08acb25075 100644
@@ -24,10 +24,13 @@
 #ifndef CONFIG_EXTRA_ENV_SETTINGS
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x80060000\0" \
-	"fdt_addr_r=0x80028000\0" \
+	"fdt_addr_r=0x80400000\0" \
 	"scriptaddr=0x80020000\0" \
 	"kernel_addr_r=0x80060000\0" \
-	"fdtfile=kendryte/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0"
+	"fdtfile=kendryte/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
+	"k210_bootcmd=load mmc 0:1 $loadaddr /uImage && " \
+		"load mmc 0:1 $fdt_addr_r /k210.dtb && " \
+		"bootm $loadaddr - $fdt_addr_r\0"
 #endif
 
 #endif /* CONFIGS_SIPEED_MAIX_H */
Signature · 1 line
2.29.2