Skip to contentSkip to conversation

Bluetooth: btusb: Add a Kconfig option to disable USB wakeup by default

PATCH In review [email protected] 2 participants 3 messages Dec 30, 2020 – Jan 25, 2021

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Bluetooth: btusb: Add a Kconfig option to disable USB wakeup by default

From: Max Chou <[email protected]>

For the original commit of 9e45524a011107a73bc2cdde8370c61e82e93a4d, wakeup is always disabled for Realtek Bluetooth devices. However, there's the capability for Realtek Bluetooth devices to apply USB wakeup. Otherwise, there's the better power consumption without USB wakeup during suspending.
In this commit, divide the original commit into two parts.
1. Redefine the feature that Realtek devices should be enabled wakeup on auto-suspend as BTUSB_WAKEUP_AUTOSUSPEND.
2. Add a Kconfig option to switch disable_wakeup for Bluetooth USB devices by default as CONFIG_BT_HCIBTUSB_DISABLEWAKEUP.

---
 drivers/bluetooth/Kconfig | 11 +++++++++++
 drivers/bluetooth/btusb.c | 41 ++++++++++++++++++++++++++-------------
 2 files changed, 38 insertions(+), 14 deletions(-)
drivers/bluetooth/Kconfig +11 -0
index 4e73a531b377..7af10897a248 100644
@@ -41,6 +41,17 @@ config BT_HCIBTUSB_AUTOSUSPEND
 	  This can be overridden by passing btusb.enable_autosuspend=[y|n]
 	  on the kernel commandline.
 
+config BT_HCIBTUSB_DISABLEWAKEUP
+	bool "Disable USB wakeup for Bluetooth USB devices by default"
+	depends on BT_HCIBTUSB
+	default n
+	help
+	  Say Y here to disable USB wakeup for Bluetooth USB devices by
+	  default.
+
+	  This can be overridden by passing btusb.disable_wakeup=[y|n]
+	  on the kernel commandline.
+
 config BT_HCIBTUSB_BCM
 	bool "Broadcom protocol support"
 	depends on BT_HCIBTUSB
drivers/bluetooth/btusb.c +27 -14

95 lines not on this page · raw message

Signature · 7 lines
2.17.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
author
#1 lore raw

// add Abhishek to CC list

BRs,
Max

-----Original Message-----
From: Max Chou <[email protected]>
Sent: Wednesday, December 30, 2020 2:55 PM
To: [email protected]; [email protected]; [email protected]; [email protected]
Cc: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; Hilda Wu <[email protected]>; KidmanLee <[email protected]>; Max Chou <[email protected]>
Subject: [PATCH] Bluetooth: btusb: Add a Kconfig option to disable USB wakeup by default

From: Max Chou <[email protected]>

For the original commit of 9e45524a011107a73bc2cdde8370c61e82e93a4d,
wakeup is always disabled for Realtek Bluetooth devices.
However, there's the capability for Realtek Bluetooth devices to apply USB wakeup. Otherwise, there's the better power consumption without USB wakeup during suspending. In this commit, divide the original commit into two parts.
1. Redefine the feature that Realtek devices should be enabled wakeup on auto-suspend as BTUSB_WAKEUP_AUTOSUSPEND.
2. Add a Kconfig option to switch disable_wakeup for Bluetooth USB devices by default as CONFIG_BT_HCIBTUSB_DISABLEWAKEUP.

---
 drivers/bluetooth/Kconfig | 11 +++++++++++  drivers/bluetooth/btusb.c | 41 ++++++++++++++++++++++++++-------------
 2 files changed, 38 insertions(+), 14 deletions(-)
drivers/bluetooth/Kconfig +11 -0
@@ -41,6 +41,17 @@ config BT_HCIBTUSB_AUTOSUSPEND
 	  This can be overridden by passing btusb.enable_autosuspend=[y|n]
 	  on the kernel commandline.
 
+config BT_HCIBTUSB_DISABLEWAKEUP
+	bool "Disable USB wakeup for Bluetooth USB devices by default"
+	depends on BT_HCIBTUSB
+	default n
+	help
+	  Say Y here to disable USB wakeup for Bluetooth USB devices by
+	  default.
+
+	  This can be overridden by passing btusb.disable_wakeup=[y|n]
+	  on the kernel commandline.
+
 config BT_HCIBTUSB_BCM
 	bool "Broadcom protocol support"
 	depends on BT_HCIBTUSB
drivers/bluetooth/btusb.c +2 -0
@@ -30,6 +30,7 @@
 static bool disable_scofix;
 static bool force_scofix;
 static bool enable_autosuspend = IS_ENABLED(CONFIG_BT_HCIBTUSB_AUTOSUSPEND);
+static bool disable_wakeup = 
+IS_ENABLED(CONFIG_BT_HCIBTUSB_DISABLEWAKEUP);
 
 static bool reset = true;

@@ -505,7 +506,7 @@ static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
#define BTUSB_OOB_WAKE_ENABLED 11
#define BTUSB_HW_RESET_ACTIVE 12
#define BTUSB_TX_WAIT_VND_EVT 13
-#define BTUSB_WAKEUP_DISABLE 14
+#define BTUSB_WAKEUP_AUTOSUSPEND 14

struct btusb_data {
struct hci_dev *hdev;
@@ -1330,7 +1331,7 @@ static int btusb_open(struct hci_dev *hdev)
* For Realtek chips, global suspend without
* SET_FEATURE (DEVICE_REMOTE_WAKEUP) can save more power in device. */
- if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
+ if (disable_wakeup)
device_wakeup_disable(&data->udev->dev);

if (test_and_set_bit(BTUSB_INTR_RUNNING, &data->flags)) @@ -1399,7 +1400,7 @@ static int btusb_close(struct hci_dev *hdev) data->intf->needs_remote_wakeup = 0;

/* Enable remote wake up for auto-suspend */
- if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
+ if (test_bit(BTUSB_WAKEUP_AUTOSUSPEND, &data->flags))
data->intf->needs_remote_wakeup = 1;

usb_autopm_put_interface(data->intf);
@@ -4257,7 +4258,7 @@ static bool btusb_prevent_wake(struct hci_dev *hdev) {
struct btusb_data *data = hci_get_drvdata(hdev);

- if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
+ if (disable_wakeup)
return true;

return !device_may_wakeup(&data->udev->dev);
@@ -4557,11 +4558,8 @@ static int btusb_probe(struct usb_interface *intf,
hdev->shutdown = btrtl_shutdown_realtek; hdev->cmd_timeout = btusb_rtl_cmd_timeout;

- /* Realtek devices lose their updated firmware over global
- * suspend that means host doesn't send SET_FEATURE
- * (DEVICE_REMOTE_WAKEUP)
- */
- set_bit(BTUSB_WAKEUP_DISABLE, &data->flags);
+ /* Realtek devices need to set USB remote wakeup on auto-suspend */
+ set_bit(BTUSB_WAKEUP_AUTOSUSPEND, &data->flags);
}

if (!reset)
@@ -4731,17 +4729,29 @@ static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
enable_irq(data->oob_wake_irq);
}

- /* For global suspend, Realtek devices lose the loaded fw
- * in them. But for autosuspend, firmware should remain.
+ /* For suspend(S3), Realtek devices lose the loaded fw
+ * if USB wakeup is disabled.
+ * It can meet better power consumption.
+ * Otherwise, the fw is alive if USB wakeup is enabled.
+ * It's able to wake Host up by the paired devices.
+ * Note that disable_wakeup should be false,
+ * and device_may_wakeup() should return true.
+ *
+ * For autosuspend, firmware should remain.
* Actually, it depends on whether the usb host sends
* set feature (enable wakeup) or not.
*/
- if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags)) {
+ if (test_bit(BTUSB_WAKEUP_AUTOSUSPEND, &data->flags)) {
if (PMSG_IS_AUTO(message) &&
device_can_wakeup(&data->udev->dev))
data->udev->do_remote_wakeup = 1;
- else if (!PMSG_IS_AUTO(message))
- data->udev->reset_resume = 1;
+ else if (!PMSG_IS_AUTO(message)) {
+ if (disable_wakeup ||
+ !device_may_wakeup(&data->udev->dev)) {
+ data->udev->do_remote_wakeup = 0;
+ data->udev->reset_resume = 1;
+ }
+ }
}

return 0;
@@ -4865,6 +4875,9 @@ MODULE_PARM_DESC(force_scofix, "Force fixup of wrong SCO buffers size"); module_param(enable_autosuspend, bool, 0644); MODULE_PARM_DESC(enable_autosuspend, "Enable USB autosuspend by default");

+module_param(disable_wakeup, bool, 0644); +MODULE_PARM_DESC(disable_wakeup, "Disable USB wakeup by default"); +
module_param(reset, bool, 0644);
MODULE_PARM_DESC(reset, "Send HCI reset command on initialization");

--
2.17.1

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

maintainer
#2 lore raw
In reply to [email protected]

Hi Max,

Quoted 10 lines

For the original commit of 9e45524a011107a73bc2cdde8370c61e82e93a4d, wakeup is always disabled for Realtek Bluetooth devices. However, there's the capability for Realtek Bluetooth devices to apply USB wakeup. Otherwise, there's the better power consumption without USB wakeup during suspending.
In this commit, divide the original commit into two parts.
1. Redefine the feature that Realtek devices should be enabled wakeup on auto-suspend as BTUSB_WAKEUP_AUTOSUSPEND.
2. Add a Kconfig option to switch disable_wakeup for Bluetooth USB devices by default as CONFIG_BT_HCIBTUSB_DISABLEWAKEUP.

lets not make this so complicated. Lets just make this work. So define this based on the Realtek hardware that supports it and not just a generic option. If your hardware is broken or works different from revision to revision, then quirk it inside the driver.

Regards

Marcel

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek