imx: imx8mp_evk: enable eth support
Subsystems (7)
PATCH v2 1/12 imx: imx8mp_evk: enable eth support
From: Peng Fan <[email protected]>
Add board code to configure the network interface
Add net defconfig
---
V2:
Use phy-reset-gpios
Use void for setup_fec
Drop empty lines
arch/arm/dts/imx8mp-evk-u-boot.dtsi | 4 ++ arch/arm/include/asm/arch-imx8m/imx-regs.h | 2 + board/freescale/imx8mp_evk/imx8mp_evk.c | 65 +++++++++++++++++++++- configs/imx8mp_evk_defconfig | 9 ++- include/configs/imx8mp_evk.h | 16 ++++++ 5 files changed, 94 insertions(+), 2 deletions(-)
arch/arm/dts/imx8mp-evk-u-boot.dtsi +4 -0
@@ -131,3 +131,7 @@ &wdog1 { u-boot,dm-spl; }; + +&fec { + phy-reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; +};
arch/arm/include/asm/arch-imx8m/imx-regs.h +2 -0
@@ -62,6 +62,8 @@#define DDRC_IPS_BASE_ADDR (X ) (0x3d400000 + ((X) * 0x2000000))#define DDR_CSD1_BASE_ADDR 0x40000000 +#define IOMUXC_GPR_GPR1_GPR_ENET_QOS_INTF_SEL_MASK 0x70000 +#if !defined(__ASSEMBLY__)#include <asm/types.h> #include <linux/bitops.h>
board/freescale/imx8mp_evk/imx8mp_evk.c +64 -1
83 lines not on this page · raw message
configs/imx8mp_evk_defconfig +8 -1
@@ -45,6 +45,9 @@ CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT2=y
@@ -71,8 +74,12 @@ CONFIG_DM_MMC=y CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_MMC_IO_VOLTAGE=y CONFIG_FSL_ESDHC_IMX=y -CONFIG_PHYLIB=y +CONFIG_PHY_REALTEK=y CONFIG_DM_ETH=y +CONFIG_PHY_GIGE=y +CONFIG_DWC_ETH_QOS=y +CONFIG_FEC_MXC=y +CONFIG_MII=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_IMX8M=y
include/configs/imx8mp_evk.h +16 -0
@@ -44,6 +44,22 @@#endif +#if defined(CONFIG_CMD_NET ) +#define CONFIG_ETHPRIME "eth1"/* Set eqos to primary since we use its MDIO */ + +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_FEC_MXC_PHYADDR 1 +#define FEC_QUIRK_ENET_MAC + +#define DWC_NET_PHYADDR 1 +#ifdef CONFIG_DWC_ETH_QOS +#define CONFIG_SYS_NONCACHED_MEMORY (1 * SZ_1M)/* 1M */ +#endif + +#define PHY_ANEG_TIMEOUT 20000 + +#endif +/* Initial environment variables */ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \
Signature · 1 line
2.28.0
PATCH v2 2/12 imx: imx8mn_ddr4_evk: Use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board
From: Peng Fan <[email protected]>
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.
--- arch/arm/mach-imx/imx8m/Kconfig | 2 +- board/freescale/imx8mn_evk/Kconfig | 2 +- configs/imx8mn_ddr4_evk_defconfig | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-)
arch/arm/mach-imx/imx8m/Kconfig +1 -1
@@ -43,7 +43,7 @@ config TARGET_IMX8MM_EVK select SUPPORT_SPL select IMX8M_LPDDR4 -config TARGET_IMX8MN_EVK +config TARGET_IMX8MN_DDR4_EVK bool "imx8mn DDR4 EVK board" select IMX8MN select SUPPORT_SPL
board/freescale/imx8mn_evk/Kconfig +1 -1
@@ -1,4 +1,4 @@ -if TARGET_IMX8MN_EVK +if TARGET_IMX8MN_DDR4_EVK config SYS_BOARD default "imx8mn_evk"
configs/imx8mn_ddr4_evk_defconfig +1 -1
@@ -12,7 +12,7 @@ CONFIG_SYS_I2C_MXC_I2C2=y CONFIG_SYS_I2C_MXC_I2C3=y CONFIG_DM_GPIO=y CONFIG_SPL_TEXT_BASE=0x912000 -CONFIG_TARGET_IMX8MN_EVK=y +CONFIG_TARGET_IMX8MN_DDR4_EVK=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
Signature · 1 line
2.28.0
PATCH v2 3/12 imx: ddr: imx8m: Move selfref_en after DDR scrub
In reply to Peng Fan (OSS)From: Ye Li <[email protected]>
When doing DDR scrub, the DDR may enter into self refresh if the selfref_en is enabled before DDR scrub. This will cause scrub can't complete that SBRSTAT.scrub_done won't be set.
Since the selfref_en can be programmed during the course of normal operation, move it after DDR scrub
--- drivers/ddr/imx/imx8m/ddr_init.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/ddr/imx/imx8m/ddr_init.c +3 -2
@@ -235,8 +235,6 @@ int ddr_init(struct dram_timing_info *dram_timing)/* Step26: Set back register in Step4 to the original values if desired */ reg32_write (DDRC_RFSHCTL3 (0 ),0x0000000 ); -/* enable selfref_en by default */ -setbits_le32 (DDRC_PWRCTL (0 ),0x1 );/* enable port 0 */ reg32_write (DDRC_PCTRL_0 (0 ),0x00000001 );
@@ -244,6 +242,9 @@ int ddr_init(struct dram_timing_info *dram_timing)board_dram_ecc_scrub (); +/* enable selfref_en by default */ +setbits_le32 (DDRC_PWRCTL (0 ),0x1 ); +/* save the dram timing config into memory */ dram_config_save (dram_timing,CONFIG_SAVED_DRAM_TIMING_BASE );
Signature · 1 line
2.28.0
PATCH v2 4/12 imx: imx8mn_evk: correct stack/malloc adress
In reply to Peng Fan (OSS)From: Peng Fan <[email protected]>
Move SP to end of OCRAM space. Drop MALLOC_F to make it alloc from stack space.
---
V2:
Typo fixes
drivers/power/power_i2c.c | 8 ++++---- include/configs/imx8mn_evk.h | 7 ++----- 2 files changed, 6 insertions(+), 9 deletions(-)
drivers/power/power_i2c.c +4 -4
@@ -23,7 +23,7 @@ int pmic_reg_write(struct pmic *p, u32 reg, u32 val)if (check_reg (p, reg))return -EINVAL ; -#if defined(CONFIG_DM_I2C ) +#if CONFIG_IS_ENABLED (DM_I2C )struct udevice *dev;int ret;
@@ -67,7 +67,7 @@ int pmic_reg_write(struct pmic *p, u32 reg, u32 val)return -EINVAL ; } -#if defined(CONFIG_DM_I2C ) +#if CONFIG_IS_ENABLED (DM_I2C )return dm_i2c_write (dev, reg, buf, pmic_i2c_tx_num);#else return i2c_write (pmic_i2c_addr, reg,1 , buf, pmic_i2c_tx_num);
@@ -83,7 +83,7 @@ int pmic_reg_read(struct pmic *p, u32 reg, u32 *val)if (check_reg (p, reg))return -EINVAL ; -#if defined(CONFIG_DM_I2C ) +#if CONFIG_IS_ENABLED (DM_I2C )struct udevice *dev; ret = i2c_get_chip_for_busnum(p->bus, pmic_i2c_addr,
@@ -131,7 +131,7 @@ int pmic_reg_read(struct pmic *p, u32 reg, u32 *val)int pmic_probe (struct pmic *p) {debug ("Bus: %d PMIC:%s probed!\n" , p->bus, p->name); -#if defined(CONFIG_DM_I2C ) +#if CONFIG_IS_ENABLED (DM_I2C )struct udevice *dev;int ret;
include/configs/imx8mn_evk.h +2 -5
@@ -20,17 +20,14 @@ (QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)#ifdef CONFIG_SPL_BUILD -#define CONFIG_SPL_STACK 0x95fff0 -#define CONFIG_SPL_BSS_START_ADDR 0x00950000 +#define CONFIG_SPL_STACK 0x980000 +#define CONFIG_SPL_BSS_START_ADDR 0x950000#define CONFIG_SPL_BSS_MAX_SIZE SZ_8K/* 8 KB */ #define CONFIG_SYS_SPL_MALLOC_START 0x42200000#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K/* 512 KB */ #define CONFIG_SYS_ICACHE_OFF #define CONFIG_SYS_DCACHE_OFF -/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */ -#define CONFIG_MALLOC_F_ADDR 0x00940000 -/* For RAW image gives a error info not panic */ #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
Signature · 1 line
2.28.0
PATCH v2 5/12 arm: dts: imx8mn: sync dts from Linux Kernel
In reply to Peng Fan (OSS)From: Peng Fan <[email protected]>
Sync dts from Linux Kernel
commit f838f8d2b694cf9d524dc("mfd: ab8500-debugfs: Remove extraneous seq_putc")
--- arch/arm/dts/imx8mn-ddr4-evk.dts | 321 +++--- arch/arm/dts/imx8mn-evk.dtsi | 360 ++++++ arch/arm/dts/imx8mn-pinfunc.h | 1266 +++++++++++----------- arch/arm/dts/imx8mn.dtsi | 411 ++++++- include/dt-bindings/clock/imx8mn-clock.h | 30 +- 5 files changed, 1501 insertions(+), 887 deletions(-) create mode 100644 arch/arm/dts/imx8mn-evk.dtsi
arch/arm/dts/imx8mn-ddr4-evk.dts +128 -193
@@ -6,216 +6,151 @@ /dts-v1/; #include "imx8mn.dtsi" +#include "imx8mn-evk.dtsi" / { model = "NXP i.MX8MNano DDR4 EVK board"; compatible = "fsl,imx8mn-ddr4-evk", "fsl,imx8mn"; - - chosen { - stdout-path = &uart2; - }; - - reg_usdhc2_vmmc: regulator-usdhc2 { - compatible = "regulator-fixed"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; - regulator-name = "VSD_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; }; -&iomuxc { - pinctrl-names = "default"; - - pinctrl_fec1: fec1grp { - fsl,pins = < - MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x3 - MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 - MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f - MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f - MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f - MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f - MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 - MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 - MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 - MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 - MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f - MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 - MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 - MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f - MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19 - >; - }; - - pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc { - fsl,pins = < - MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 - >; - }; +&A53_0 { + cpu-supply = <&buck2_reg>; +}; - pinctrl_uart2: uart2grp { - fsl,pins = < - MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 - MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 - >; - }; +&A53_1 { + cpu-supply = <&buck2_reg>; +}; - pinctrl_usdhc2_gpio: usdhc2grpgpio { - fsl,pins = < - MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x1c4 - >; - }; +&A53_2 { + cpu-supply = <&buck2_reg>; +}; - pinctrl_usdhc2: usdhc2grp { - fsl,pins = < - MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 - MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 - MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 - MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 - MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 - MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 - MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 - >; - }; +&A53_3 { + cpu-supply = <&buck2_reg>; +}; - pinctrl_usdhc2_100mhz: usdhc2grp100mhz { - fsl,pins = < - MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 - MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 - MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 - MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 - MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 - MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 - MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 - >; - }; +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; - pinctrl_usdhc2_200mhz: usdhc2grp200mhz { - fsl,pins = < - MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 - MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 - MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 - MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 - MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 - MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 - MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 - >; - }; + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; - pinctrl_usdhc3: usdhc3grp { - fsl,pins = < - MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000190 - MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 - MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 - MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 - MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 - MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 - MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 - MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 - MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 - MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 - MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 - >; - }; - - pinctrl_usdhc3_100mhz: usdhc3grp100mhz { - fsl,pins = < - MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000194 - MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 - MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 - MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 - MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 - MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 - MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 - MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 - MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 - MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 - MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 - >; - }; + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; - pinctrl_usdhc3_200mhz: usdhc3grp200mhz { - fsl,pins = < - MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000196 - MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 - MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 - MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 - MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 - MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 - MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 - MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 - MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 - MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 - MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 - >; - }; + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; - pinctrl_wdog: wdoggrp { - fsl,pins = < - MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 - >; + opp-600M { + opp-hz = /bits/ 64 <600000000>; + }; }; }; -&fec1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec1>; - phy-mode = "rgmii-id"; - phy-handle = <ðphy0>; - fsl,magic-packet; - status = "okay"; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - ethphy0: ethernet-phy at 0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0>; - at803x,led-act-blind-workaround; - at803x,eee-disabled; - at803x,vddio-1p8v; +&i2c1 { + pmic at 4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck3_reg: BUCK3 { + // BUCK5 in datasheet + regulator-name = "buck3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + }; + + buck4_reg: BUCK4 { + // BUCK6 in datasheet + regulator-name = "buck4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + // BUCK7 in datasheet + regulator-name = "buck5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + // BUCK8 in datasheet + regulator-name = "buck6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; }; }; }; - -&snvs_pwrkey { - status = "okay"; -}; - -&uart2 { /* console */ - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; - status = "okay"; -}; - -&usdhc2 { - pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; - pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; - pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; - cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - bus-width = <4>; - vmmc-supply = <®_usdhc2_vmmc>; - status = "okay"; -}; - -&usdhc3 { - pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc3>; - pinctrl-1 = <&pinctrl_usdhc3_100mhz>; - pinctrl-2 = <&pinctrl_usdhc3_200mhz>; - bus-width = <8>; - non-removable; - status = "okay"; -}; - -&wdog1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_wdog>; - fsl,ext-reset-output; - status = "okay"; -};
arch/arm/dts/imx8mn-evk.dtsi new file +360 -0
360 lines not on this page · raw message
arch/arm/dts/imx8mn-pinfunc.h +633 -633
1,276 lines not on this page · raw message
arch/arm/dts/imx8mn.dtsi +353 -58
627 lines not on this page · raw message
include/dt-bindings/clock/imx8mn-clock.h +27 -3
@@ -122,8 +122,8 @@#define IMX8MN_CLK_I2C1 105#define IMX8MN_CLK_I2C2 106#define IMX8MN_CLK_I2C3 107 -#define IMX8MN_CLK_I2C4 118 -#define IMX8MN_CLK_UART1 119 +#define IMX8MN_CLK_I2C4 108 +#define IMX8MN_CLK_UART1 109#define IMX8MN_CLK_UART2 110#define IMX8MN_CLK_UART3 111#define IMX8MN_CLK_UART4 112
@@ -209,7 +209,31 @@#define IMX8MN_CLK_ARM 191#define IMX8MN_CLK_NAND_USDHC_BUS_RAWNAND_CLK 192#define IMX8MN_CLK_GPU_CORE_ROOT 193 +#define IMX8MN_CLK_GIC 194 -#define IMX8MN_CLK_END 194 +#define IMX8MN_SYS_PLL1_40M_CG 195 +#define IMX8MN_SYS_PLL1_80M_CG 196 +#define IMX8MN_SYS_PLL1_100M_CG 197 +#define IMX8MN_SYS_PLL1_133M_CG 198 +#define IMX8MN_SYS_PLL1_160M_CG 199 +#define IMX8MN_SYS_PLL1_200M_CG 200 +#define IMX8MN_SYS_PLL1_266M_CG 201 +#define IMX8MN_SYS_PLL1_400M_CG 202 +#define IMX8MN_SYS_PLL2_50M_CG 203 +#define IMX8MN_SYS_PLL2_100M_CG 204 +#define IMX8MN_SYS_PLL2_125M_CG 205 +#define IMX8MN_SYS_PLL2_166M_CG 206 +#define IMX8MN_SYS_PLL2_200M_CG 207 +#define IMX8MN_SYS_PLL2_250M_CG 208 +#define IMX8MN_SYS_PLL2_333M_CG 209 +#define IMX8MN_SYS_PLL2_500M_CG 210 + +#define IMX8MN_CLK_SNVS_ROOT 211 +#define IMX8MN_CLK_GPU_CORE 212 +#define IMX8MN_CLK_GPU_SHADER 213 + +#define IMX8MN_CLK_A53_CORE 214 + +#define IMX8MN_CLK_END 215#endif
Signature · 1 line
2.28.0
PATCH v2 6/12 imx: imx8mn: add i.MX8MN LPDDR4 EVK support
In reply to Peng Fan (OSS)From: Peng Fan <[email protected]>
i.MX8MN LPDDR4 EVK reuses most code of i.MX8MN DDR4 EVK code, with adding a new ddr script.
---
V2:
Update doc
arch/arm/dts/Makefile | 1 + arch/arm/dts/imx8mn-evk-u-boot.dtsi | 6 + arch/arm/dts/imx8mn-evk.dts | 128 ++ arch/arm/mach-imx/imx8m/Kconfig | 6 + .../mach-imx/imx8m/imximage-8mn-lpddr4.cfg | 17 + board/freescale/imx8mn_evk/Kconfig | 2 +- board/freescale/imx8mn_evk/Makefile | 1 + board/freescale/imx8mn_evk/lpddr4_timing.c | 1585 +++++++++++++++++ configs/imx8mn_evk_defconfig | 80 + doc/board/freescale/imx8mn_evk.rst | 20 +- 10 files changed, 1840 insertions(+), 6 deletions(-) create mode 100644 arch/arm/dts/imx8mn-evk-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mn-evk.dts create mode 100644 arch/arm/mach-imx/imx8m/imximage-8mn-lpddr4.cfg create mode 100644 board/freescale/imx8mn_evk/lpddr4_timing.c create mode 100644 configs/imx8mn_evk_defconfig
arch/arm/dts/Makefile +1 -0
@@ -775,6 +775,7 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mm-verdin.dtb \ phycore-imx8mm.dtb \ imx8mn-ddr4-evk.dtb \ + imx8mn-evk.dtb \ imx8mq-evk.dtb \ imx8mm-beacon-kit.dtb \ imx8mq-phanbell.dtb \
arch/arm/dts/imx8mn-evk-u-boot.dtsi new file +6 -0
@@ -0,0 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 NXP + */ + +#include "imx8mn-ddr4-evk-u-boot.dtsi"
arch/arm/dts/imx8mn-evk.dts new file +128 -0
128 lines not on this page · raw message
arch/arm/mach-imx/imx8m/Kconfig +6 -0
@@ -43,6 +43,12 @@ config TARGET_IMX8MM_EVK select SUPPORT_SPL select IMX8M_LPDDR4 +config TARGET_IMX8MN_EVK + bool "imx8mn LPDDR4 EVK board" + select IMX8MN + select SUPPORT_SPL + select IMX8M_LPDDR4 + config TARGET_IMX8MN_DDR4_EVK bool "imx8mn DDR4 EVK board" select IMX8MN
arch/arm/mach-imx/imx8m/imximage-8mn-lpddr4.cfg new file +17 -0
@@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 NXP + */ + +#define __ASSEMBLY__ + +FIT +ROM_VERSION v2 +BOOT_FROM sd +LOADER spl/u-boot-spl-ddr.bin 0x912000 +SECOND_LOADER u-boot.itb 0x40200000 0x60000 + +DDR_FW lpddr4_pmu_train_1d_imem.bin +DDR_FW lpddr4_pmu_train_1d_dmem.bin +DDR_FW lpddr4_pmu_train_2d_imem.bin +DDR_FW lpddr4_pmu_train_2d_dmem.bin
board/freescale/imx8mn_evk/Kconfig +1 -1
@@ -1,4 +1,4 @@ -if TARGET_IMX8MN_DDR4_EVK +if TARGET_IMX8MN_EVK || TARGET_IMX8MN_DDR4_EVK config SYS_BOARD default "imx8mn_evk"
board/freescale/imx8mn_evk/Makefile +1 -0
@@ -8,5 +8,6 @@ obj-y += imx8mn_evk.o ifdef CONFIG_SPL_BUILD obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o obj-$(CONFIG_IMX8M_DDR4) += ddr4_timing.o endif
board/freescale/imx8mn_evk/lpddr4_timing.c new file +1585 -0
1,585 lines not on this page · raw message
configs/imx8mn_evk_defconfig new file +80 -0
80 lines not on this page · raw message
doc/board/freescale/imx8mn_evk.rst +15 -5
@@ -18,7 +18,7 @@ Get and Build the ARM Trusted firmware Note: srctree is U-Boot source directory Get ATF from: https://source.codeaurora.org/external/imx/imx-atf -branch: imx_4.19.35_1.1.0 +branch: imx_5.4.70_2.3.0 .. code-block:: bash
@@ -30,18 +30,28 @@ Get the ddr firmware .. code-block:: bash - $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.5.bin - $ chmod +x firmware-imx-8.5.bin - $ ./firmware-imx-8.5 + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin + $ chmod +x firmware-imx-8.9.bin + $ ./firmware-imx-8.9 + +Choose ddr4 or lpddr4 firmware, do not copy both. +If your board is imx8mn_ddr4_evk board, use below: + +.. code-block:: bash $ cp firmware-imx-8.5/firmware/ddr/synopsys/ddr4*.bin $(srctree) + +If your board is imx8mn_ddr4_evk board, use below: +.. code-block:: bash + $ cp firmware-imx-8.5/firmware/ddr/synopsys/lpddr4*.bin $(srctree) + Build U-Boot ------------ .. code-block:: bash $ export CROSS_COMPILE=aarch64-poky-linux- - $ make imx8mn_ddr4_evk_defconfig + $ make imx8mn_ddr4_evk_defconfig or imx8mn_evk_defconfig $ export ATF_LOAD_ADDR=0x960000 $ make flash.bin
Signature · 1 line
2.28.0
PATCH v2 7/12 imx8m: clock: add type of set_clk_eqos
In reply to Peng Fan (OSS)From: Peng Fan <[email protected]>
Add type of set_clk_eqos to make it could be used by other files.
--- arch/arm/include/asm/arch-imx8m/clock.h | 1 + 1 file changed, 1 insertion(+)
arch/arm/include/asm/arch-imx8m/clock.h +1 -0
@@ -274,3 +274,4 @@ int set_clk_qspi(void);void enable_ocotp_clk (unsigned char enable);int enable_i2c_clk (unsigned char enable,unsigned int i2c_num);int set_clk_enet (enum enet_freq type); +int set_clk_eqos (enum enet_freq type);
Signature · 1 line
2.28.0
PATCH v2 8/12 arm: dts: imx8mp: sync dts from Linux Kernel
In reply to Peng Fan (OSS)From: Peng Fan <[email protected]>
Sync dts from Linux Kernel
commit f838f8d2b694cf9d524dc("mfd: ab8500-debugfs: Remove extraneous seq_putc")
--- arch/arm/dts/imx8mp-evk.dts | 117 +++++++- arch/arm/dts/imx8mp-pinfunc.h | 360 +++++++---------------- arch/arm/dts/imx8mp.dtsi | 234 +++++++++++++-- include/dt-bindings/clock/imx8mp-clock.h | 95 +++++- 4 files changed, 528 insertions(+), 278 deletions(-)
arch/arm/dts/imx8mp-evk.dts +108 -9
@@ -15,12 +15,46 @@ stdout-path = &uart2; }; + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_led>; + + status { + label = "yellow:status"; + gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + memory at 40000000 { device_type = "memory"; reg = <0x0 0x40000000 0 0xc0000000>, <0x1 0x00000000 0 0xc0000000>; }; + reg_can1_stby: regulator-can1-stby { + compatible = "regulator-fixed"; + regulator-name = "can1-stby"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1_reg>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_can2_stby: regulator-can2-stby { + compatible = "regulator-fixed"; + regulator-name = "can2-stby"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2_reg>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + reg_usdhc2_vmmc: regulator-usdhc2 { compatible = "regulator-fixed"; pinctrl-names = "default";
@@ -33,6 +67,20 @@ }; }; +&flexcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_can1_stby>; + status = "okay"; +}; + +&flexcan2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + xceiver-supply = <®_can2_stby>; + status = "disabled";/* can2 pin conflict with pdm */ +}; + &fec { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_fec>;
@@ -54,6 +102,20 @@ }; }; +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + pca6416: gpio at 20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + &snvs_pwrkey { status = "okay"; };
@@ -98,8 +160,6 @@ }; &iomuxc { - pinctrl-names = "default"; - pinctrl_fec: fecgrp { fsl,pins = < MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
@@ -120,7 +180,46 @@ >; }; - pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc { + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_RX__CAN1_RX 0x154 + MX8MP_IOMUXC_SPDIF_TX__CAN1_TX 0x154 + >; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX 0x154 + MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX 0x154 + >; + }; + + pinctrl_flexcan1_reg: flexcan1reggrp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05 0x154 /* CAN1_STBY */ + >; + }; + + pinctrl_flexcan2_reg: flexcan2reggrp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27 0x154 /* CAN2_STBY */ + >; + }; + + pinctrl_gpio_led: gpioledgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16 0x19 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c3 + MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { fsl,pins = < MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41 >;
@@ -145,7 +244,7 @@ >; }; - pinctrl_usdhc2_100mhz: usdhc2grp-100mhz { + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { fsl,pins = < MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194 MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4
@@ -157,7 +256,7 @@ >; }; - pinctrl_usdhc2_200mhz: usdhc2grp-200mhz { + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { fsl,pins = < MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196 MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6
@@ -169,7 +268,7 @@ >; }; - pinctrl_usdhc2_gpio: usdhc2grp-gpio { + pinctrl_usdhc2_gpio: usdhc2gpiogrp { fsl,pins = < MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4 >;
@@ -191,7 +290,7 @@ >; }; - pinctrl_usdhc3_100mhz: usdhc3grp-100mhz { + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { fsl,pins = < MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
@@ -207,7 +306,7 @@ >; }; - pinctrl_usdhc3_200mhz: usdhc3grp-200mhz { + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { fsl,pins = < MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
@@ -225,7 +324,7 @@ pinctrl_wdog: wdoggrp { fsl,pins = < - MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6 + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0x166 >; }; };
arch/arm/dts/imx8mp-pinfunc.h +114 -246
977 lines not on this page · raw message
arch/arm/dts/imx8mp.dtsi +214 -20
387 lines not on this page · raw message
include/dt-bindings/clock/imx8mp-clock.h +92 -3
113 lines not on this page · raw message
Signature · 1 line
2.28.0
PATCH v2 9/12 arm: dts: imx8mm: sync dts from Linux Kernel
In reply to Peng Fan (OSS)From: Peng Fan <[email protected]>
Sync dts from Linux Kernel
commit f838f8d2b694cf9d524dc("mfd: ab8500-debugfs: Remove extraneous seq_putc")
--- arch/arm/dts/imx8mm-evk.dts | 534 ++++------------------- arch/arm/dts/imx8mm-evk.dtsi | 489 +++++++++++++++++++++ arch/arm/dts/imx8mm.dtsi | 172 ++++++-- include/dt-bindings/clock/imx8mm-clock.h | 28 +- 4 files changed, 740 insertions(+), 483 deletions(-) create mode 100644 arch/arm/dts/imx8mm-evk.dtsi
arch/arm/dts/imx8mm-evk.dts +77 -457
@@ -1,309 +1,61 @@ // SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* - * Copyright 2019 NXP + * Copyright 2019-2020 NXP */ /dts-v1/; #include <dt-bindings/usb/pd.h> -#include "imx8mm.dtsi" +#include "imx8mm-evk.dtsi" / { model = "FSL i.MX8MM EVK board"; compatible = "fsl,imx8mm-evk", "fsl,imx8mm"; - chosen { - stdout-path = &uart2; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio_led>; - - status { - label = "status"; - gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - }; - - reg_usdhc2_vmmc: regulator-usdhc2 { - compatible = "regulator-fixed"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; - regulator-name = "VSD_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - wm8524: audio-codec { - #sound-dai-cells = <0>; - compatible = "wlf,wm8524"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio_wlf>; - wlf,mute-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; - }; - - sound-wm8524 { - compatible = "simple-audio-card"; - simple-audio-card,name = "wm8524-audio"; - simple-audio-card,format = "i2s"; - simple-audio-card,frame-master = <&cpudai>; - simple-audio-card,bitclock-master = <&cpudai>; - simple-audio-card,widgets = - "Line", "Left Line Out Jack", - "Line", "Right Line Out Jack"; - simple-audio-card,routing = - "Left Line Out Jack", "LINEVOUTL", - "Right Line Out Jack", "LINEVOUTR"; - - cpudai: simple-audio-card,cpu { - sound-dai = <&sai3>; - }; - - simple-audio-card,codec { - sound-dai = <&wm8524>; - clocks = <&clk IMX8MM_CLK_SAI3_ROOT>; - }; + aliases { + spi0 = &flexspi; }; }; -&A53_0 { - cpu-supply = <&buck2_reg>; -}; - -&fec1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec1>; - phy-mode = "rgmii-id"; - phy-handle = <ðphy0>; - fsl,magic-packet; - status = "okay"; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - ethphy0: ethernet-phy at 0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0>; - }; - }; -}; - -&i2c1 { - clock-frequency = <400000>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1>; - status = "okay"; - - pmic at 4b { - compatible = "rohm,bd71847"; - reg = <0x4b>; - pinctrl-0 = <&pinctrl_pmic>; - interrupt-parent = <&gpio1>; - interrupts = <3 GPIO_ACTIVE_LOW>; - rohm,reset-snvs-powered; - - regulators { - buck1_reg: BUCK1 { - regulator-name = "BUCK1"; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1300000>; - regulator-boot-on; - regulator-always-on; - regulator-ramp-delay = <1250>; - }; - - buck2_reg: BUCK2 { - regulator-name = "BUCK2"; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1300000>; - regulator-boot-on; - regulator-always-on; - regulator-ramp-delay = <1250>; - rohm,dvs-run-voltage = <1000000>; - rohm,dvs-idle-voltage = <900000>; - }; - - buck3_reg: BUCK3 { - // BUCK5 in datasheet - regulator-name = "BUCK3"; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1350000>; - regulator-boot-on; - regulator-always-on; - }; - - buck4_reg: BUCK4 { - // BUCK6 in datasheet - regulator-name = "BUCK4"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - - buck5_reg: BUCK5 { - // BUCK7 in datasheet - regulator-name = "BUCK5"; - regulator-min-microvolt = <1605000>; - regulator-max-microvolt = <1995000>; - regulator-boot-on; - regulator-always-on; - }; - - buck6_reg: BUCK6 { - // BUCK8 in datasheet - regulator-name = "BUCK6"; - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <1400000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo1_reg: LDO1 { - regulator-name = "LDO1"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; - ldo2_reg: LDO2 { - regulator-name = "LDO2"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <900000>; - regulator-boot-on; - regulator-always-on; - }; + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; - ldo3_reg: LDO3 { - regulator-name = "LDO3"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo4_reg: LDO4 { - regulator-name = "LDO4"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo6_reg: LDO6 { - regulator-name = "LDO6"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - }; + opp-25M { + opp-hz = /bits/ 64 <25000000>; }; - }; -}; -&i2c2 { - clock-frequency = <400000>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2>; - status = "okay"; - - ptn5110: tcpc at 50 { - compatible = "nxp,ptn5110"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_typec1>; - reg = <0x50>; - interrupt-parent = <&gpio2>; - interrupts = <11 8>; - status = "okay"; - - port { - typec1_dr_sw: endpoint { - remote-endpoint = <&usb1_drd_sw>; - }; + opp-100M { + opp-hz = /bits/ 64 <100000000>; }; - typec1_con: connector { - compatible = "usb-c-connector"; - label = "USB-C"; - power-role = "dual"; - data-role = "dual"; - try-power-role = "sink"; - source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; - sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) - PDO_VAR(5000, 20000, 3000)>; - op-sink-microwatt = <15000000>; - self-powered; + opp-750M { + opp-hz = /bits/ 64 <750000000>; }; }; }; -&i2c3 { - clock-frequency = <400000>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3>; - status = "okay"; - - pca6416: gpio at 20 { - compatible = "ti,tca6416"; - reg = <0x20>; - gpio-controller; - #gpio-cells = <2>; - }; -}; - -&sai3 { +&flexspi { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_sai3>; - assigned-clocks = <&clk IMX8MM_CLK_SAI3>; - assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; - assigned-clock-rates = <24576000>; + pinctrl-0 = <&pinctrl_flexspi>; status = "okay"; -}; - -&snvs_pwrkey { - status = "okay"; -}; -&uart2 { /* console */ - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; - status = "okay"; -}; - -&usbotg1 { - dr_mode = "otg"; - hnp-disable; - srp-disable; - adp-disable; - usb-role-switch; - status = "okay"; - - port { - usb1_drd_sw: endpoint { - remote-endpoint = <&typec1_dr_sw>; - }; + flash at 0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <80000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; }; }; -&usdhc2 { - pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; - pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; - pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; - cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - bus-width = <4>; - vmmc-supply = <®_usdhc2_vmmc>; - status = "okay"; -}; - &usdhc3 { + assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>; + assigned-clock-rates = <400000000>; pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc3>; pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
@@ -313,196 +65,64 @@ status = "okay"; }; -&wdog1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_wdog>; - fsl,ext-reset-output; - status = "okay"; -}; - &iomuxc { - pinctrl-names = "default"; - - pinctrl_fec1: fec1grp { - fsl,pins = < - MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 - MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 - MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f - MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f - MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f - MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f - MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 - MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 - MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 - MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 - MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f - MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 - MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 - MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f - MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19 - >; - }; - - pinctrl_gpio_led: gpioledgrp { - fsl,pins = < - MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 - >; - }; - - pinctrl_gpio_wlf: gpiowlfgrp { + pinctrl_flexspi: flexspigrp { fsl,pins = < - MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21 0xd6 - >; - }; - - pinctrl_i2c1: i2c1grp { - fsl,pins = < - MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 - MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 - >; - }; - - pinctrl_i2c2: i2c2grp { - fsl,pins = < - MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 - MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 - >; - }; - - pinctrl_i2c3: i2c3grp { - fsl,pins = < - MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 - MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 - >; - }; - - pinctrl_pmic: pmicirq { - fsl,pins = < - MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 - >; - }; - - pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc { - fsl,pins = < - MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 - >; - }; - - pinctrl_sai3: sai3grp { - fsl,pins = < - MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 - MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 - MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 - MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 - >; - }; - - pinctrl_typec1: typec1grp { - fsl,pins = < - MX8MM_IOMUXC_SD1_STROBE_GPIO2_IO11 0x159 - >; - }; - - pinctrl_uart2: uart2grp { - fsl,pins = < - MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 - MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 - >; - }; - - pinctrl_usdhc2_gpio: usdhc2grpgpio { - fsl,pins = < - MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x1c4 - >; - }; - - pinctrl_usdhc2: usdhc2grp { - fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 - MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 - MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 - MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 - MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 - MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 - >; - }; - - pinctrl_usdhc2_100mhz: usdhc2grp100mhz { - fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 - MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 - MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 - MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 - MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 - MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 - >; - }; - - pinctrl_usdhc2_200mhz: usdhc2grp200mhz { - fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 - MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 - MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 - MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 - MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 - MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2 + MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 + MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 + MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 + MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 + MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 >; }; pinctrl_usdhc3: usdhc3grp { fsl,pins = < - MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 - MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 - MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 - MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 - MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 - MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 - MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 - MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 - MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 - MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 - MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 - >; - }; - - pinctrl_usdhc3_100mhz: usdhc3grp100mhz { - fsl,pins = < - MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 - MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 - MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 - MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 - MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 - MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 - MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 - MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 - MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 - MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 - MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 - >; - }; - - pinctrl_usdhc3_200mhz: usdhc3grp200mhz { - fsl,pins = < - MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 - MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 - MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 - MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 - MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 - MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 - MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 - MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 - MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 - MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 - MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 - >; - }; - - pinctrl_wdog: wdoggrp { - fsl,pins = < - MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 >; }; };
arch/arm/dts/imx8mm-evk.dtsi new file +489 -0
489 lines not on this page · raw message
arch/arm/dts/imx8mm.dtsi +147 -25
343 lines not on this page · raw message
include/dt-bindings/clock/imx8mm-clock.h +27 -1
@@ -248,6 +248,32 @@#define IMX8MM_CLK_SNVS_ROOT 228#define IMX8MM_CLK_GIC 229 -#define IMX8MM_CLK_END 230 +#define IMX8MM_SYS_PLL1_40M_CG 230 +#define IMX8MM_SYS_PLL1_80M_CG 231 +#define IMX8MM_SYS_PLL1_100M_CG 232 +#define IMX8MM_SYS_PLL1_133M_CG 233 +#define IMX8MM_SYS_PLL1_160M_CG 234 +#define IMX8MM_SYS_PLL1_200M_CG 235 +#define IMX8MM_SYS_PLL1_266M_CG 236 +#define IMX8MM_SYS_PLL1_400M_CG 237 +#define IMX8MM_SYS_PLL2_50M_CG 238 +#define IMX8MM_SYS_PLL2_100M_CG 239 +#define IMX8MM_SYS_PLL2_125M_CG 240 +#define IMX8MM_SYS_PLL2_166M_CG 241 +#define IMX8MM_SYS_PLL2_200M_CG 242 +#define IMX8MM_SYS_PLL2_250M_CG 243 +#define IMX8MM_SYS_PLL2_333M_CG 244 +#define IMX8MM_SYS_PLL2_500M_CG 245 + +#define IMX8MM_CLK_M4_CORE 246 +#define IMX8MM_CLK_VPU_CORE 247 +#define IMX8MM_CLK_GPU3D_CORE 248 +#define IMX8MM_CLK_GPU2D_CORE 249 + +#define IMX8MM_CLK_CLKO2 250 + +#define IMX8MM_CLK_A53_CORE 251 + +#define IMX8MM_CLK_END 252#endif
Signature · 1 line
2.28.0
PATCH v2 10/12 arm: dts: imx8mq: sync dts from Linux Kernel
In reply to Peng Fan (OSS)From: Peng Fan <[email protected]>
Sync dts from Linux Kernel
commit f838f8d2b694cf9d524dc("mfd: ab8500-debugfs: Remove extraneous seq_putc")
--- arch/arm/dts/imx8mq-evk.dts | 186 +++++-- arch/arm/dts/imx8mq-pinfunc.h | 623 +++++++++++++++++++++++ arch/arm/dts/imx8mq.dtsi | 302 ++++++++++- include/dt-bindings/clock/imx8mq-clock.h | 31 +- 4 files changed, 1097 insertions(+), 45 deletions(-) create mode 100644 arch/arm/dts/imx8mq-pinfunc.h
arch/arm/dts/imx8mq-evk.dts +156 -30
@@ -6,9 +6,6 @@ /dts-v1/; -/* First 128KB is for PSCI ATF. */ -/memreserve/ 0x40000000 0x00020000; - #include "imx8mq.dtsi" / {
@@ -51,6 +48,16 @@ gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; states = <1000000 0x0 900000 0x1>; + regulator-boot-on; + regulator-always-on; + }; + + ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ir>; + linux,autosuspend-period = <125>; }; wm8524: audio-codec {
@@ -81,6 +88,21 @@ clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>; }; }; + + sound-spdif { + compatible = "fsl,imx-audio-spdif"; + model = "imx-spdif"; + spdif-controller = <&spdif1>; + spdif-out; + spdif-in; + }; + + sound-hdmi-arc { + compatible = "fsl,imx-audio-spdif"; + model = "imx-hdmi-arc"; + spdif-controller = <&spdif2>; + spdif-in; + }; }; &A53_0 {
@@ -99,13 +121,42 @@ cpu-supply = <&buck2_reg>; }; +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + + /* + * On imx8mq B0 PLL can't be bypassed so low bus is 166M + */ + opp-166M { + opp-hz = /bits/ 64 <166935483>; + }; + + opp-800M { + opp-hz = /bits/ 64 <800000000>; + }; + }; +}; + +&dphy { + status = "okay"; +}; + &fec1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_fec1>; phy-mode = "rgmii-id"; phy-handle = <ðphy0>; - phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; - phy-reset-duration = <10>; fsl,magic-packet; status = "okay";
@@ -116,24 +167,17 @@ ethphy0: ethernet-phy at 0 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <0>; + reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; }; }; }; -&sai2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_sai2>; - assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1_BYPASS>, <&clk IMX8MQ_CLK_SAI2>; - assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL1_OUT>; - assigned-clock-rates = <0>, <24576000>; - status = "okay"; -}; - &gpio5 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_wifi_reset>; - wl-reg-on { + wl-reg-on-hog { gpio-hog; gpios = <29 GPIO_ACTIVE_HIGH>; output-high;
@@ -231,6 +275,40 @@ }; }; +&lcdif { + status = "okay"; +}; + +&mipi_dsi { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + panel at 0 { + pinctrl-0 = <&pinctrl_mipi_dsi>; + pinctrl-names = "default"; + compatible = "raydium,rm67191"; + reg = <0>; + reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>; + dsi-lanes = <4>; + + port { + panel_in: endpoint { + remote-endpoint = <&mipi_dsi_out>; + }; + }; + }; + + ports { + port at 1 { + reg = <1>; + mipi_dsi_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + &pcie0 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>;
@@ -247,10 +325,49 @@ power-supply = <&sw1a_reg>; }; +&qspi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi>; + status = "okay"; + + n25q256a: flash at 0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a", "jedec,spi-nor"; + spi-max-frequency = <29000000>; + }; +}; + +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1_BYPASS>, <&clk IMX8MQ_CLK_SAI2>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL1_OUT>; + assigned-clock-rates = <0>, <24576000>; + status = "okay"; +}; + &snvs_pwrkey { status = "okay"; }; +&spdif1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spdif1>; + assigned-clocks = <&clk IMX8MQ_CLK_SPDIF1>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + +&spdif2 { + assigned-clocks = <&clk IMX8MQ_CLK_SPDIF2>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + &uart1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>;
@@ -266,21 +383,9 @@ status = "okay"; }; -&qspi0 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_qspi>; - status = "okay"; - - n25q256a: flash at 0 { - reg = <0>; - #address-cells = <1>; - #size-cells = <1>; - compatible = "micron,n25q256a", "jedec,spi-nor"; - spi-max-frequency = <29000000>; - }; -}; - &usdhc1 { + assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>; + assigned-clock-rates = <400000000>; pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc1>; pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
@@ -294,6 +399,8 @@ }; &usdhc2 { + assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>; + assigned-clock-rates = <200000000>; pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc2>; pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
@@ -345,6 +452,18 @@ >; }; + pinctrl_ir: irgrp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x4f + >; + }; + + pinctrl_mipi_dsi: mipidsigrp { + fsl,pins = < + MX8MQ_IOMUXC_ECSPI1_SCLK_GPIO5_IO6 0x16 + >; + }; + pinctrl_pcie0: pcie0grp { fsl,pins = < MX8MQ_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x76
@@ -364,7 +483,7 @@ >; }; - pinctrl_reg_usdhc2: regusdhc2grpgpio { + pinctrl_reg_usdhc2: regusdhc2gpiogrp { fsl,pins = < MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 >;
@@ -380,6 +499,13 @@ >; }; + pinctrl_spdif1: spdif1grp { + fsl,pins = < + MX8MQ_IOMUXC_SPDIF_TX_SPDIF1_OUT 0xd6 + MX8MQ_IOMUXC_SPDIF_RX_SPDIF1_IN 0xd6 + >; + }; + pinctrl_uart1: uart1grp { fsl,pins = < MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
arch/arm/dts/imx8mq-pinfunc.h new file +623 -0
623 lines not on this page · raw message
arch/arm/dts/imx8mq.dtsi +288 -14
480 lines not on this page · raw message
include/dt-bindings/clock/imx8mq-clock.h +30 -1
@@ -403,5 +403,34 @@#define IMX8MQ_CLK_SNVS_ROOT 264#define IMX8MQ_CLK_GIC 265 -#define IMX8MQ_CLK_END 266 +#define IMX8MQ_VIDEO2_PLL1_REF_SEL 266 + +#define IMX8MQ_SYS1_PLL_40M_CG 267 +#define IMX8MQ_SYS1_PLL_80M_CG 268 +#define IMX8MQ_SYS1_PLL_100M_CG 269 +#define IMX8MQ_SYS1_PLL_133M_CG 270 +#define IMX8MQ_SYS1_PLL_160M_CG 271 +#define IMX8MQ_SYS1_PLL_200M_CG 272 +#define IMX8MQ_SYS1_PLL_266M_CG 273 +#define IMX8MQ_SYS1_PLL_400M_CG 274 +#define IMX8MQ_SYS1_PLL_800M_CG 275 +#define IMX8MQ_SYS2_PLL_50M_CG 276 +#define IMX8MQ_SYS2_PLL_100M_CG 277 +#define IMX8MQ_SYS2_PLL_125M_CG 278 +#define IMX8MQ_SYS2_PLL_166M_CG 279 +#define IMX8MQ_SYS2_PLL_200M_CG 280 +#define IMX8MQ_SYS2_PLL_250M_CG 281 +#define IMX8MQ_SYS2_PLL_333M_CG 282 +#define IMX8MQ_SYS2_PLL_500M_CG 283 +#define IMX8MQ_SYS2_PLL_1000M_CG 284 + +#define IMX8MQ_CLK_GPU_CORE 285 +#define IMX8MQ_CLK_GPU_SHADER 286 +#define IMX8MQ_CLK_M4_CORE 287 +#define IMX8MQ_CLK_VPU_CORE 288 + +#define IMX8MQ_CLK_A53_CORE 289 + +#define IMX8MQ_CLK_END 290 +#endif /* __DT_BINDINGS_CLOCK_IMX8MQ_H */
Signature · 1 line
2.28.0
PATCH v2 11/12 imx8m: lowlevel_init: tune alignment
In reply to Peng Fan (OSS)From: Peng Fan <[email protected]>
The minimum alignment is 16 bytes, so use align 4 is enough.
--- arch/arm/mach-imx/imx8m/lowlevel_init.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-imx/imx8m/lowlevel_init.S +1 -1
@@ -5,7 +5,7 @@ #include <config.h> -.align 8 +.align 4 .global rom_pointer rom_pointer: .space 256
Signature · 1 line
2.28.0
PATCH v2 12/12 imx: imx8m: move CONFIG_SPL_SYS_[I, D]CACHE_OFF to defconfig
In reply to Peng Fan (OSS)From: Peng Fan <[email protected]>
move CONFIG_SPL_SYS_[I,D]CACHE_OFF to defconfig
--- configs/imx8mn_ddr4_evk_defconfig | 2 ++ configs/imx8mn_evk_defconfig | 2 ++ configs/imx8mp_evk_defconfig | 2 ++ include/configs/imx8mn_evk.h | 2 -- include/configs/imx8mp_evk.h | 2 -- 5 files changed, 6 insertions(+), 4 deletions(-)
configs/imx8mn_ddr4_evk_defconfig +2 -0
@@ -1,4 +1,6 @@ CONFIG_ARM=y +CONFIG_SPL_SYS_ICACHE_OFF=y +CONFIG_SPL_SYS_DCACHE_OFF=y CONFIG_ARCH_IMX8M=y CONFIG_SYS_TEXT_BASE=0x40200000 CONFIG_SPL_GPIO_SUPPORT=y
configs/imx8mn_evk_defconfig +2 -0
@@ -1,4 +1,6 @@ CONFIG_ARM=y +CONFIG_SPL_SYS_ICACHE_OFF=y +CONFIG_SPL_SYS_DCACHE_OFF=y CONFIG_ARCH_IMX8M=y CONFIG_SYS_TEXT_BASE=0x40200000 CONFIG_SPL_GPIO_SUPPORT=y
configs/imx8mp_evk_defconfig +2 -0
@@ -1,4 +1,6 @@ CONFIG_ARM=y +CONFIG_SPL_SYS_ICACHE_OFF=y +CONFIG_SPL_SYS_DCACHE_OFF=y CONFIG_ARCH_IMX8M=y CONFIG_SYS_TEXT_BASE=0x40200000 CONFIG_SPL_GPIO_SUPPORT=y
include/configs/imx8mn_evk.h +0 -2
@@ -25,8 +25,6 @@#define CONFIG_SPL_BSS_MAX_SIZE SZ_8K/* 8 KB */ #define CONFIG_SYS_SPL_MALLOC_START 0x42200000#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K/* 512 KB */ -#define CONFIG_SYS_ICACHE_OFF -#define CONFIG_SYS_DCACHE_OFF /* For RAW image gives a error info not panic */ #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
include/configs/imx8mp_evk.h +0 -2
@@ -26,8 +26,6 @@#define CONFIG_SPL_BSS_MAX_SIZE 0x400/* 1 KB */ #define CONFIG_SYS_SPL_MALLOC_START 0x42200000#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K/* 512 KB */ -#define CONFIG_SYS_ICACHE_OFF -#define CONFIG_SYS_DCACHE_OFF #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
Signature · 1 line
2.28.0
Fabio Estevam
reviewerPATCH v2 12/12 imx: imx8m: move CONFIG_SPL_SYS_[I,D]CACHE_OFF to defconfig
Hi Peng
configs/imx8mn_ddr4_evk_defconfig line 3
Quoted 8 lines · Peng Fan (OSS)
configs/imx8mn_ddr4_evk_defconfig +2
-0@@ -1,4 +1,6 @@ CONFIG_ARM=y +CONFIG_SPL_SYS_ICACHE_OFF=y +CONFIG_SPL_SYS_DCACHE_OFF=y
I understand that this patch is just moving these symbols from include file to defconfig, but a more fundamental question: why do we need to disable caches in the first place?
My understanding is that it is safe to run with caches enabled on these imx8 platforms.
Please clarify.
Thanks,
Fabio Estevam
Peng Fan
reviewerPATCH v2 12/12 imx: imx8m: move CONFIG_SPL_SYS_[I,D]CACHE_OFF to defconfig
Quoted 8 lines
Subject: Re: [PATCH V2 12/12] imx: imx8m: move
CONFIG_SPL_SYS_[I,D]CACHE_OFF to defconfigHi Peng
On Sun, Jan 3, 2021 at 6:43 AM Peng Fan (OSS) <[email protected]> wrote:
Quoted 13 lines
configs/imx8mn_ddr4_evk_defconfig line 3
Quoted 9 lines
configs/imx8mn_ddr4_evk_defconfig +2
-0@@ -1,4 +1,6 @@ CONFIG_ARM=y +CONFIG_SPL_SYS_ICACHE_OFF=y +CONFIG_SPL_SYS_DCACHE_OFF=yI understand that this patch is just moving these symbols from include file to defconfig, but a more fundamental question: why do we need to disable caches in the first place?
No need to disable icache. Dcache needs to be off, since we not have MMU setup.
I could use a follow up patch to enable icache, agree?
Thanks,
Peng.
Quoted 9 lines
My understanding is that it is safe to run with caches enabled on these imx8 platforms.
Please clarify.
Thanks,
Fabio Estevam
Fabio Estevam
reviewerPATCH v2 12/12 imx: imx8m: move CONFIG_SPL_SYS_[I,D]CACHE_OFF to defconfig
Hi Peng,
Quoted 2 lines · Peng Fan
No need to disable icache. Dcache needs to be off, since we not have MMU setup.
Is the requirement to disable D-Cache in SPL specific to i.MX8MN and i.MX8MP?
We do not pass CONFIG_SPL_SYS_ICACHE_OFF=y and CONFIG_SPL_SYS_DCACHE_OFF=y for imx8mq_evk_defconfig, for example.
Regards,
Fabio Estevam