Skip to contentSkip to conversation

irqchip/irq-pruss-intc: implement set_type() callback

PATCH In review David Lechner 2 participants 3 messages Jan 4, 2021 – Jan 5, 2021 irqchip drivers

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 irqchip/irq-pruss-intc: implement set_type() callback

This implements the irqchip set_type() callback for the TI PRUSS interrupt controller. This is needed for cases where an event needs to be active low.

According to the technical reference manual, the polarity should always be set to high, however in practice, the polarity needs to be set low for the McASP Tx/Rx system event in conjunction with soft UART PRU firmware for TI AM18XX SoCs, otherwise it doesn't work.

---
 drivers/irqchip/irq-pruss-intc.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/irqchip/irq-pruss-intc.c +27 -0
index 5409016e6ca0..f882af8a7ded 100644
@@ -334,6 +334,32 @@ static void pruss_intc_irq_unmask(struct irq_data *data)
 	pruss_intc_write_reg(intc, PRU_INTC_EISR, hwirq);
 }
 
+static int pruss_intc_irq_set_type(struct irq_data *data, unsigned int type)
+{
+	struct pruss_intc *intc = irq_data_get_irq_chip_data(data);
+	u32 reg, bit, val;
+
+	if (type & IRQ_TYPE_LEVEL_MASK) {
+		/* polarity register */
+		reg = PRU_INTC_SIPR(data->hwirq / 32);
+		bit = BIT(data->hwirq % 32);
+		val = pruss_intc_read_reg(intc, reg);
+
+		/*
+		 * This check also ensures that IRQ_TYPE_DEFAULT will result
+		 * in setting the level to high.
+		 */
+		if (type & IRQ_TYPE_LEVEL_HIGH)
+			val |= bit;
+		else
+			val &= ~bit;
+
+		pruss_intc_write_reg(intc, reg, val);
+	}
+
+	return 0;
+}
+
 static int pruss_intc_irq_reqres(struct irq_data *data)
 {
 	if (!try_module_get(THIS_MODULE))
@@ -389,6 +415,7 @@ static struct irq_chip pruss_irqchip = {
 	.irq_ack		= pruss_intc_irq_ack,
 	.irq_mask		= pruss_intc_irq_mask,
 	.irq_unmask		= pruss_intc_irq_unmask,
+	.irq_set_type		= pruss_intc_irq_set_type,
 	.irq_request_resources	= pruss_intc_irq_reqres,
 	.irq_release_resources	= pruss_intc_irq_relres,
 	.irq_get_irqchip_state	= pruss_intc_irq_get_irqchip_state,
Signature · 1 line
2.25.1
#1 lore raw
Quoted 8 lines · David Lechner

This implements the irqchip set_type() callback for the TI PRUSS interrupt controller. This is needed for cases where an event needs to be active low.

According to the technical reference manual, the polarity should always be set to high, however in practice, the polarity needs to be set low for the McASP Tx/Rx system event in conjunction with soft UART PRU firmware for TI AM18XX SoCs, otherwise it doesn't work.

I remember asking about this when I reviewed the patch series, and was told that there was no need to handle anything *but* level high. As a consequence, the DT binding doesn't have any way to express the trigger configuration.

Now this? What is going to drive the configuration?

Quoted 27 lines
---
 drivers/irqchip/irq-pruss-intc.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/irqchip/irq-pruss-intc.c +11 -0
index 5409016e6ca0..f882af8a7ded 100644
@@ -334,6 +334,32 @@ static void pruss_intc_irq_unmask(struct irq_data 
 *data)
 	pruss_intc_write_reg(intc, PRU_INTC_EISR, hwirq);
 }
 
+static int pruss_intc_irq_set_type(struct irq_data *data, unsigned int 
 type)
+{
+	struct pruss_intc *intc = irq_data_get_irq_chip_data(data);
+	u32 reg, bit, val;
+
+	if (type & IRQ_TYPE_LEVEL_MASK) {
+		/* polarity register */
+		reg = PRU_INTC_SIPR(data->hwirq / 32);
+		bit = BIT(data->hwirq % 32);
+		val = pruss_intc_read_reg(intc, reg);
+

drivers/irqchip/irq-pruss-intc.c static void pruss_intc_irq_unmask(struct irq_data · line 359

Quoted 10 lines
drivers/irqchip/irq-pruss-intc.c +10 -0
+		/*
+		 * This check also ensures that IRQ_TYPE_DEFAULT will result
+		 * in setting the level to high.
+		 */
+		if (type & IRQ_TYPE_LEVEL_HIGH)
+			val |= bit;
+		else
+			val &= ~bit;
+
+		pruss_intc_write_reg(intc, reg, val);

RMW of a shared register without locking?

drivers/irqchip/irq-pruss-intc.c static void pruss_intc_irq_unmask(struct irq_data *data) · line 360

Quoted 3 lines
drivers/irqchip/irq-pruss-intc.c +3 -0
+	}
+
+	return 0;

What happens when this is passed an edge configuration? It should at least return an error.

drivers/irqchip/irq-pruss-intc.c static struct irq_chip pruss_irqchip = { · line 421

Quoted 13 lines
drivers/irqchip/irq-pruss-intc.c +2 -0
+}
+
 static int pruss_intc_irq_reqres(struct irq_data *data)

{

drivers/irqchip/irq-pruss-intc.c +1 -0
 	if (!try_module_get(THIS_MODULE))
@@ -389,6 +415,7 @@ static struct irq_chip pruss_irqchip = {
 	.irq_ack		= pruss_intc_irq_ack,
 	.irq_mask		= pruss_intc_irq_mask,
 	.irq_unmask		= pruss_intc_irq_unmask,
+	.irq_set_type		= pruss_intc_irq_set_type,
 	.irq_request_resources	= pruss_intc_irq_reqres,
 	.irq_release_resources	= pruss_intc_irq_relres,
 	.irq_get_irqchip_state	= pruss_intc_irq_get_irqchip_state,

Thanks,

        M.
Signature · 1 line
Jazz is not dead. It just smells funny...
#2 lore raw
Quoted 10 lines · Marc Zyngier
Quoted 8 lines · David Lechner

This implements the irqchip set_type() callback for the TI PRUSS interrupt controller. This is needed for cases where an event needs to be active low.

According to the technical reference manual, the polarity should always be set to high, however in practice, the polarity needs to be set low for the McASP Tx/Rx system event in conjunction with soft UART PRU firmware for TI AM18XX SoCs, otherwise it doesn't work.

Quoted 6 lines

I remember asking about this when I reviewed the patch series, and was told that there was no need to handle anything *but* level high. As a consequence, the DT binding doesn't have any way to express the trigger configuration.

Now this? What is going to drive the configuration?

I made it work by setting IRQF_TRIGGER_LOW in devm_request_irq().

I can try to see if there is a way to change the (10 year old) firmware instead.

Hopefully someone from TI can shed more light on the subject?

Quoted 39 lines
Quoted 26 lines

---
 drivers/irqchip/irq-pruss-intc.c | 27 +++++++++++++++++++++++++++

 1 file changed, 27 insertions(+)
drivers/irqchip/irq-pruss-intc.c +11 -0
index 5409016e6ca0..f882af8a7ded 100644
@@ -334,6 +334,32 @@ static void pruss_intc_irq_unmask(struct irq_data *data)
      pruss_intc_write_reg(intc, PRU_INTC_EISR, hwirq);
  }
 
+static int pruss_intc_irq_set_type(struct irq_data *data, unsigned int type)
+{
+    struct pruss_intc *intc = irq_data_get_irq_chip_data(data);
+    u32 reg, bit, val;
+
+    if (type & IRQ_TYPE_LEVEL_MASK) {
+        /* polarity register */
+        reg = PRU_INTC_SIPR(data->hwirq / 32);
+        bit = BIT(data->hwirq % 32);
+        val = pruss_intc_read_reg(intc, reg);
+

drivers/irqchip/irq-pruss-intc.c static void pruss_intc_irq_unmask(struct irq_data *data) · line 357

Quoted 10 lines
drivers/irqchip/irq-pruss-intc.c +10 -0
+        /*
+         * This check also ensures that IRQ_TYPE_DEFAULT will result
+         * in setting the level to high.
+         */
+        if (type & IRQ_TYPE_LEVEL_HIGH)
+            val |= bit;
+        else
+            val &= ~bit;
+
+        pruss_intc_write_reg(intc, reg, val);

RMW  of a shared register without locking?

Quoted 6 lines

drivers/irqchip/irq-pruss-intc.c static void pruss_intc_irq_unmask(struct irq_data *data) · line 360

Quoted 3 lines
drivers/irqchip/irq-pruss-intc.c +3 -0
+    }
+
+    return 0;

What happens when this is passed an edge configuration? It should at least return an error.

This is probably a moot point if we are not going to allow changing the type, but there is another register for selecting edge or level. But the manual says similarly says it should always be set to level.

Quoted 18 lines
Quoted 7 lines
drivers/irqchip/irq-pruss-intc.c +2 -0
+}
+
  static int pruss_intc_irq_reqres(struct irq_data *data)
  {
      if (!try_module_get(THIS_MODULE))

drivers/irqchip/irq-pruss-intc.c static struct irq_chip pruss_irqchip = { · line 421

Quoted 7 lines
drivers/irqchip/irq-pruss-intc.c +1 -0
@@ -389,6 +415,7 @@ static struct irq_chip pruss_irqchip = {
      .irq_ack        = pruss_intc_irq_ack,
      .irq_mask        = pruss_intc_irq_mask,
      .irq_unmask        = pruss_intc_irq_unmask,
+    .irq_set_type        = pruss_intc_irq_set_type,
      .irq_request_resources    = pruss_intc_irq_reqres,
      .irq_release_resources    = pruss_intc_irq_relres,
      .irq_get_irqchip_state    = pruss_intc_irq_get_irqchip_state,

Thanks,

        M.