Skip to contentSkip to conversation

Fix SPI Chipselect/Clock bug for sun6i

PATCH In review Ralf Schlatterbeck 2 participants 5 messages Dec 26, 2020 – May 20, 2021

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Fix SPI Chipselect/Clock bug for sun6i

This patch makes additional GPIOs usable as chipselects for SPI. It is available for years on the linux-sunxi SPIdev page at
http://linux-sunxi.org/SPIdev and probably is originally by the user "Mirko" there. I've tried unsuccessfully to contact the author. Note that contrary to what is stated on the page above, the bug doesn't have cosmetic implications only:

The SPI-Driver for the H2 Allwinner processor in the Linux kernel is supposed to support normal GPIOs as additional chipselects but fails to do so without the patch.

For oscilloscope screenshots with/without the patch, see my blog post
https://blog.runtux.com/posts/2019/04/18/
or the discussion in the armbian forum at
https://forum.armbian.com/topic/4330-spi-gpio-chip-select-support/
(my logo there is a penguin).
Please bear with me if I'm not following proper procedures, this is my first patch to the kernel in years.

Thanks
Ralf Schlatterbeck

From 682ae1848b0df00cceb4c76486b971826b2737a9 Mon Sep 17 00:00:00 2001
From: Ralf Schlatterbeck <[email protected]>
Date: Thu, 11 Apr 2019 16:21:54 +0200
Subject: [PATCH] Fix SPI Chipselect/Clock bug for sun6i

The current sun6i SPI implementation initializes the transfer too early, resulting in SCK going high before the transer. When using an additional (gpio) chipselect with sun6i, the chipselect is asserted at a time when clock is high, making the SPI transfer fail. This patch from the sunxi spidev page http://linux-sunxi.org/SPIdev fixes this, without the patch no additional gpio chipselects can be used. The relevant code seems to be from the user "Mirko" of the linux-sunxi wiki page, I was unable to contact the original author.

---
 drivers/spi/spi-sun6i.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/spi/spi-sun6i.c +5 -1
index 19238e1b76b4..9b292c6ade50 100644
@@ -290,6 +290,10 @@ static int sun6i_spi_transfer_one(struct spi_master *master,
 	}
 
 	sun6i_spi_write(sspi, SUN6I_CLK_CTL_REG, reg);
+	/* Finally enable the bus - doing so before might raise SCK to HIGH */
+	sun6i_spi_write(sspi, SUN6I_GBL_CTL_REG,
+			sun6i_spi_read(sspi, SUN6I_GBL_CTL_REG)
+			| SUN6I_GBL_CTL_BUS_ENABLE);
 
 	/* Setup the transfer now... */
 	if (sspi->tx_buf)
@@ -398,7 +402,7 @@ static int sun6i_spi_runtime_resume(struct device *dev)
 	}
 
 	sun6i_spi_write(sspi, SUN6I_GBL_CTL_REG,
-			SUN6I_GBL_CTL_BUS_ENABLE | SUN6I_GBL_CTL_MASTER | SUN6I_GBL_CTL_TP);
+			SUN6I_GBL_CTL_MASTER | SUN6I_GBL_CTL_TP);
 
 	return 0;
 
Signature · 5 lines
2.20.1
-- 
Dr. Ralf Schlatterbeck                  Tel:   +43/2243/26465-16
Open Source Consulting                  www:   www.runtux.com
Reichergasse 131, A-3411 Weidling       email: [email protected]
#1 lore raw

Hi,

Quoted 28 lines · Ralf Schlatterbeck

This patch makes additional GPIOs usable as chipselects for SPI. It is available for years on the linux-sunxi SPIdev page at
http://linux-sunxi.org/SPIdev and probably is originally by the user "Mirko" there. I've tried unsuccessfully to contact the author. Note that contrary to what is stated on the page above, the bug doesn't have cosmetic implications only:

The SPI-Driver for the H2 Allwinner processor in the Linux kernel is supposed to support normal GPIOs as additional chipselects but fails to do so without the patch.

For oscilloscope screenshots with/without the patch, see my blog post
https://blog.runtux.com/posts/2019/04/18/
or the discussion in the armbian forum at
https://forum.armbian.com/topic/4330-spi-gpio-chip-select-support/
(my logo there is a penguin).
Please bear with me if I'm not following proper procedures, this is my first patch to the kernel in years.

Thanks
Ralf Schlatterbeck

From 682ae1848b0df00cceb4c76486b971826b2737a9 Mon Sep 17 00:00:00 2001
From: Ralf Schlatterbeck <[email protected]>
Date: Thu, 11 Apr 2019 16:21:54 +0200
Subject: [PATCH] Fix SPI Chipselect/Clock bug for sun6i

Quoted 8 lines

The current sun6i SPI implementation initializes the transfer too early, resulting in SCK going high before the transer. When using an additional (gpio) chipselect with sun6i, the chipselect is asserted at a time when clock is high, making the SPI transfer fail. This patch from the sunxi spidev page http://linux-sunxi.org/SPIdev fixes this, without the patch no additional gpio chipselects can be used. The relevant code seems to be from the user "Mirko" of the linux-sunxi wiki page, I was unable to contact the original author.

Unfortunately, without the author's Signed-off-by (and yours), we can't merge that patch.

Maxime

#2 lore raw
Quoted 3 lines · Maxime Ripard

Unfortunately, without the author's Signed-off-by (and yours), we can't merge that patch.

Thanks for the Reply. I've researched more and found out who the probable Author of the patch is. I've tried to contact him via Email, I'll follow up with correct signed-off etc when I've got permission.

Ralf

Signature · 3 lines
Dr. Ralf Schlatterbeck                  Tel:   +43/2243/26465-16
Open Source Consulting                  www:   www.runtux.com
Reichergasse 131, A-3411 Weidling       email: [email protected]
#3 lore raw
Quoted 8 lines · Ralf Schlatterbeck
Quoted 3 lines · Maxime Ripard

Unfortunately, without the author's Signed-off-by (and yours), we can't merge that patch.

Thanks for the Reply. I've researched more and found out who the probable Author of the patch is. I've tried to contact him via Email, I'll follow up with correct signed-off etc when I've got permission.

Great, thanks!
Maxime

#4 lore raw
Quoted 6 lines · Maxime Ripard
Quoted 5 lines · Ralf Schlatterbeck
Quoted 3 lines · Maxime Ripard

Unfortunately, without the author's Signed-off-by (and yours), we can't merge that patch.

Quoted 6 lines
Quoted 3 lines

Thanks for the Reply. I've researched more and found out who the probable Author of the patch is. I've tried to contact him via Email, I'll follow up with correct signed-off etc when I've got permission.

Great, thanks!
Maxime

I've finally got permission :-) I'll re-submit in a separate thread.

Ralf

Signature · 8 lines
Dr. Ralf Schlatterbeck                  Tel:   +43/2243/26465-16
Open Source Consulting                  www:   www.runtux.com
Reichergasse 131, A-3411 Weidling       email: [email protected]

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel