net: phy: realtek: Add support for RTL9000AA/AN
Subsystems (3)
PATCH v2 1/1 net: phy: realtek: Add support for RTL9000AA/AN
RTL9000AA/AN as 100BASE-T1 is following:
- 100 Mbps
- Full duplex
- Link Status Change Interrupt
---
v2:
- Remove the use of .ack_interrupt()
- Implement .handle_interrupt() callback
- Remove the slash from driver name
--- drivers/net/phy/realtek.c | 81 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 81 insertions(+)
drivers/net/phy/realtek.c +81 -0
@@ -60,6 +60,9 @@#define RTL_LPADV_5000FULL BIT(6)#define RTL_LPADV_2500FULL BIT(5) +#define RTL9000A_GINMR 0x14 +#define RTL9000A_GINMR_LINK_STATUS BIT(4) +#define RTLGEN_SPEED_MASK 0x0630#define RTL_GENERIC_PHYID 0x001cc800
@@ -655,6 +658,71 @@ static int rtlgen_resume(struct phy_device *phydev)return ret; } +static int rtl9000a_config_init (struct phy_device *phydev) +{ + phydev->autoneg =AUTONEG_DISABLE ; + phydev->speed =SPEED_100 ; + phydev->duplex =DUPLEX_FULL ; + +return 0 ; +} + +static int rtl9000a_config_aneg (struct phy_device *phydev) +{ +return 0 ; +} + +static int rtl9000a_ack_interrupt (struct phy_device *phydev) +{ +int err; + + err =phy_read (phydev,RTL8211F_INSR ); + +return (err <0 ) ? err :0 ; +} + +static int rtl9000a_config_intr (struct phy_device *phydev) +{ +u16 val; +int err; + +if (phydev->interrupts ==PHY_INTERRUPT_ENABLED ) { + err =rtl9000a_ack_interrupt (phydev); +if (err) +return err; + + val = (u16 )~RTL9000A_GINMR_LINK_STATUS ; + err =phy_write_paged (phydev,0xa42 ,RTL9000A_GINMR , val); + }else { + val = ~0 ; + err =phy_write_paged (phydev,0xa42 ,RTL9000A_GINMR , val); +if (err) +return err; + + err =rtl9000a_ack_interrupt (phydev); + } + +return phy_write_paged (phydev,0xa42 ,RTL9000A_GINMR , val); +} + +static irqreturn_t rtl9000a_handle_interrupt (struct phy_device *phydev) +{ +int irq_status; + + irq_status =phy_read (phydev,RTL8211F_INSR ); +if (irq_status <0 ) { +phy_error (phydev); +return IRQ_NONE ; + } + +if (!(irq_status &RTL8211F_INER_LINK_STATUS )) +return IRQ_NONE ; + +phy_trigger_machine (phydev); + +return IRQ_HANDLED ; +} +static struct phy_driver realtek_drvs[] = { {PHY_ID_MATCH_EXACT (0x00008201 ),
@@ -823,6 +891,19 @@ static struct phy_driver realtek_drvs[] = { .handle_interrupt = genphy_handle_interrupt_no_ack, .suspend = genphy_suspend, .resume = genphy_resume, + }, { + PHY_ID_MATCH_EXACT(0x001ccb00), + .name = "RTL9000AA_RTL9000AN Ethernet", + .features = PHY_BASIC_T1_FEATURES, + .config_init = rtl9000a_config_init, + .config_aneg = rtl9000a_config_aneg, + .read_status = genphy_update_link, + .config_intr = rtl9000a_config_intr, + .handle_interrupt = rtl9000a_handle_interrupt, + .suspend = genphy_suspend, + .resume = genphy_resume, + .read_page = rtl821x_read_page, + .write_page = rtl821x_write_page, }, };
Signature · 1 line
2.29.2
Russell King - ARM Linux admin
reviewerQuoted 7 lines · Yuusuke Ashizuka
RTL9000AA/AN as 100BASE-T1 is following:
- 100 Mbps
- Full duplex
- Link Status Change InterruptSigned-off-by Yuusuke Ashizuka <[email protected]>Signed-off-by Torii Kenichi <[email protected]>
Not a review comment on your patch, but, we really need to do something with the way phylib handles configuration changes - we have the current situation where config_aneg() _will_ get called for PHYs like this that do not support autonegotiation if userspace attempts to enable autoneg - there is nothing in phy_ethtool_ksettings_set() that prevents this.
Returning an error from config_aneg() achieves nothing, and resetting the settings in config_init() also does nothing to avoid autonegotiation being enabled.
I think we need phy_ethtool_ksettings_set() to check whether ETHTOOL_LINK_MODE_Autoneg_BIT is set in phydev->supported before allowing the AUTONEG_ENABLE case.
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
Andrew Lunn
maintainerQuoted 4 lines · Yuusuke Ashizuka
RTL9000AA/AN as 100BASE-T1 is following:
- 100 Mbps
- Full duplex
- Link Status Change Interrupt
Hi Yuusuke
For T1, it seems like Master is pretty important. Do you have information to be able to return the current Master/slave configuration, or allow it to be configured? See the nxp-tja11xx.c for an example.
Thanks
Andrew
Quoted 4 lines
For T1, it seems like Master is pretty important. Do you have information to be able to return the current Master/slave configuration, or allow it to be configured? See the
nxp-tja11xx.cfor an example.
I think it's possible to return a Master/Slave configuration.
By the way, do you need the cable test function as implemented in nxp-tja11xx.c?
Thanks & Best Regards,
Yuusuke Ashiduka
Andrew Lunn
maintainerQuoted 6 lines · On Tue, Jan 12, 2021 at 05:14:21AM +0000, [email protected] wrote:
Quoted 4 lines
For T1, it seems like Master is pretty important. Do you have information to be able to return the current Master/slave configuration, or allow it to be configured? See the
nxp-tja11xx.cfor an example.I think it's possible to return a Master/Slave configuration.
Great. It would be good to add it.
Quoted 2 lines
By the way, do you need the cable test function as implemented in
nxp-tja11xx.c?
We don't need it. But if you want to implement it, that would be great.
Andrew
Quoted 3 lines
Quoted 1 line
I think it's possible to return a Master/Slave configuration.
Great. It would be good to add it.
OK. I think it will take some time to implement this feature, as we prioritize investigating comments from Russell.
Quoted 5 lines
Quoted 2 lines
By the way, do you need the cable test function as implementedin
nxp-tja11xx.c?We don't need it. But if you want to implement it, that would be great.
We also don't need the cable test feature.
However, we are interested in adding this feature, so we will consider adding the cable test feature after the RTL9000AA/AN support are merged.
Thanks & Best Regards,
Yuusuke Ashiduka
Hi Andrew
Quoted 4 lines
For T1, it seems like Master is pretty important. Do you have information to be able to return the current Master/slave configuration, or allow it to be configured? See the
nxp-tja11xx.cfor an example.
Do you know how to switch between master/slave?
The help of the ethtool command can show about the "master-slave" option, but it doesn't seem to handle the arguments.
I checked ethtool.c and it seems that do_sset () doesn't implement the process of parsing master-slave arguments...
Thanks & Best Regards,
Yuusuke Ashiduka
Andrew Lunn
maintainerQuoted 8 lines · On Thu, Jan 14, 2021 at 08:38:12AM +0000, [email protected] wrote:
Hi Andrew
Quoted 4 lines
For T1, it seems like Master is pretty important. Do you have information to be able to return the current Master/slave configuration, or allow it to be configured? See the
nxp-tja11xx.cfor an example.Do you know how to switch between master/slave?
There was a patch to ethtool merged for this:
commit 558f7cc33daf82f945af432c79db40edcbe0dad0
Author: Oleksij Rempel <[email protected]> Date: Wed Jun 10 10:37:43 2020 +0200
netlink: add master/slave configuration support
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of auto-negotiation support, we needed to be able to configure the MASTER-SLAVE role of the port manually or from an application in user space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9) 22.2.4.3.8 MASTER-SLAVE status register (Register 10) 40.5.2 MASTER-SLAVE configuration resolution 45.2.1.185.1 MASTER-SLAVE config value (1.2100.14) 45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall source TX_TCLK from a local clock source. When configured as SLAVE, the PMA Transmit function shall source TX_TCLK from the clock recovered from data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Andrew
Hi Andrew
Quoted 9 lines
Quoted 1 line
Do you know how to switch between master/slave?
There was a patch to ethtool merged for this:
commit
558f7cc33daf82f945af432c79db40edcbe0dad0Author: Oleksij Rempel <[email protected]> Date: Wed Jun 10 10:37:43 2020 +0200netlink: add master/slave configuration support
I know this.
--
# ./ethtool --version ethtool version 5.10 # ./ethtool -s eth1 master-slave slave-force ethtool (-s): invalid value 'slave-force' for parameter 'master-slave' --
As I wrote in the previous e-mail, it doesn't work because it doesn't include the process to parse the master-slave argument.
Quoted 4 lines
The help of the ethtool command can show about the "master-slave" option, but it doesn't seem to handle the arguments.
I checkedethtool.cand it seems thatdo_sset() doesn't implement the process of parsing master-slave arguments...
Once ethtool works properly, I will test the master-slave switching behavior.
Andrew Lunn
maintainerQuoted 10 lines · On Mon, Jan 18, 2021 at 10:17:04AM +0000, [email protected] wrote:
Hi Andrew
Quoted 8 lines
Quoted 1 line
Do you know how to switch between master/slave?
There was a patch to ethtool merged for this:
commit
558f7cc33daf82f945af432c79db40edcbe0dad0Author: Oleksij Rempel <[email protected]> Date: Wed Jun 10 10:37:43 2020 +0200
Quoted 8 lines
Quoted 1 line
netlink: add master/slave configuration support
I know this.
--# ./ethtool --version ethtool version 5.10 # ./ethtool -s eth1 master-slave slave-force ethtool (-s): invalid value 'slave-force' for parameter 'master-slave'
The parameter is called 'forced-slave'. See the man page:
ethtool -s devname [speed N] [duplex half|full] [port tp|aui|bnc|mii]
[mdix auto|on|off] [autoneg on|off] [advertise N[/M] | advertise mode on|off ...] [phyad N] [xcvr internal|external] [wol N[/M] | wol p|u|m|b|a|g|s|f|d...]
[sopass xx:yy:zz:aa:bb:cc] [master-slave preferred- master|preferred-slave|forced-master|forced-slave] [msglvl N[/M] | msglvl type on|off ...]
sudo ethtool -s eth10 master-slave forced-master
netlink error: master/slave configuration not supported by device (offset 36) netlink error: Operation not supported
Andrew
Hi Andrew
Quoted 1 line
The parameter is called 'forced-slave'. See the man page:
Umm...
# ./ethtool --help
ethtool [ FLAGS ] -s|--change DEVNAME Change generic options
[ speed %d ]
[ duplex half|full ]
[ port tp|aui|bnc|mii|fibre|da ]
[ mdix auto|on|off ]
[ autoneg on|off ]
[ advertise %x[/%x] | mode on|off ... [--] ]
[ phyad %d ]
[ xcvr internal|external ]
[ wol %d[/%d] | p|u|m|b|a|g|s|f|d... ]
[ sopass %x:%x:%x:%x:%x:%x ]
[ msglvl %d[/%d] | type on|off ... [--] ]
[ master-slave master-preferred|slave-preferred|master-force|slave-force ]
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The help for the ethtool command seems to be wrong...Quoted 4 lines
sudo ethtool -s eth10 master-slave forced-master netlink error: master/slave configuration not supported by device (offset 36)
netlink error: Operation not supported
It seems to work. Thanks!
# ./ethtool -s eth1 master-slave forced-slave [36173.937680] rtl9000a_config_aneg: master_slave_set=5 [36173.942891] rtl9000a_config_aneg: phy_modify_changed()=1 [36174.008502] libphy: genphy_setup_forced: speed=100, duplex=1 [36174.014283] rtl9000a_config_aneg: ret=0 [36174.018513] rtl9000a_read_status: PHYCR=0x0000 [36174.023074] rtl9000a_read_status: PHYSR1=0x0000 [36174.027653] ravb e6800000.ethernet eth1: Link is Down [36174.033116] rtl9000a_read_status: PHYCR=0x0000 [36174.037702] rtl9000a_read_status: PHYSR1=0x0000
I will test it for a while, and if there is no problem, I will post the 3rd patch.