drm/vc4: hdmi: Add CEC support for the BCM2711
Subsystems (10)
v2 cover drm/vc4: hdmi: Add CEC support for the BCM2711
Hi,
Here's a series introducing the CEC support for the BCM2711 found on the RaspberryPi4.
The BCM2711 HDMI controller uses a similar layout for the CEC registers, the main difference being that the interrupt handling part is now shared between both HDMI controllers.
This series is mainly about fixing a couple of bugs, reworking the driver to support having two different interrupts, one for each direction, provided by an external irqchip, and enables the irqchip driver for the controller we have.
This has been tested on an RPi3 and RPi4, but requires the latest firmware. It's is based on the 10 and 12 bpc series.
Here is the cec-compliance output:
pi@raspberrypi:~$ cec-ctl --tuner -p 1.0.0.0 The CEC adapter doesn't allow setting the physical address manually, ignore this option.
Driver Info:
Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e
Logical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask : 0x0008
CEC Version : 2.0
Vendor ID : 0x000c03 (HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
None
pi@raspberrypi:~$ cec-compliance cec-compliance SHA : not available Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : 1.0.0.0 Logical Address Mask : 0x0008 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Tuner Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : 3 (Tuner 1) Primary Device Type : Tuner Logical Address Type : Tuner All Device Types : Tuner RC TV Profile : None Device Features :
None
Compliance test for device /dev/cec0:
The test results mean the following:
OK Supported correctly by the device.
OK (Not Supported) Not supported and not mandatory for the device.
OK (Presumed) Presumably supported. Manually check to confirm.
OK (Unexpected) Supported correctly but is not expected to be supported for this device.
OK (Refused) Supported by the device, but was refused.
FAIL Failed and was expected to be supported by this device.
Find remote devices:
Polling: OK
Network topology:
System Information for device 0 (TV) from device 3 (Tuner 1):
CEC Version : 2.0
Physical Address : 0.0.0.0
Primary Device Type : TV
Vendor ID : 0x000c03
OSD Name : 'TV '
Power Status : Tx, OK, Rx, OK, Feature Abort
Total: 1, Succeeded: 1, Failed: 0, Warnings: 0
pi@raspberrypi:~$ cec-ctl -d1 --tuner -p 1.0.0.0 The CEC adapter doesn't allow setting the physical address manually, ignore this option.
Driver Info:
Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e
Logical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask : 0x0008
CEC Version : 2.0
Vendor ID : 0x000c03 (HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
None
pi@raspberrypi:~$ cec-compliance -d1 cec-compliance SHA : not available Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : 1.0.0.0 Logical Address Mask : 0x0008 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Tuner Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : 3 (Tuner 1) Primary Device Type : Tuner Logical Address Type : Tuner All Device Types : Tuner RC TV Profile : None Device Features :
None
Compliance test for device /dev/cec1:
The test results mean the following:
OK Supported correctly by the device.
OK (Not Supported) Not supported and not mandatory for the device.
OK (Presumed) Presumably supported. Manually check to confirm.
OK (Unexpected) Supported correctly but is not expected to be supported for this device.
OK (Refused) Supported by the device, but was refused.
FAIL Failed and was expected to be supported by this device.
Find remote devices:
Polling: OK
Network topology:
System Information for device 0 (TV) from device 3 (Tuner 1):
CEC Version : 2.0
Physical Address : 0.0.0.0
Primary Device Type : TV
Vendor ID : 0x000c03
OSD Name : 'TV '
Power Status : Tx, OK, Rx, OK, Feature Abort
Total: 1, Succeeded: 1, Failed: 0, Warnings: 0
And for the hotplug detect test:
pi@raspberrypi:~$ cec-ctl --playback Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :
None
pi@raspberrypi:~$ cec-ctl -t0 --image-view-on Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :
None
Transmit from Unregistered to TV (15 to 0):CEC_MSG_IMAGE_VIEW_ON (0x04)
Sequence: 1 Tx Timestamp: 9182.611s pi@raspberrypi:~$ cec-ctl -d1 --playback Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :
None
pi@raspberrypi:~$ cec-ctl -d1 -t0 --image-view-on Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :
None
Transmit from Unregistered to TV (15 to 0):CEC_MSG_IMAGE_VIEW_ON (0x04)
Sequence: 1 Tx Timestamp: 9207.191s
With the pulse-eight side reporting:
$ sudo cec-ctl -M Driver Info: Driver Name : pulse8-cec Adapter Name : serio0 Capabilities : 0x0000003f Physical Address Logical Addresses Transmit Passthrough Remote Control Support Monitor All Driver version : 5.9.16 Available Logical Addresses: 1 Connector Info : None Physical Address : 0.0.0.0 Logical Address Mask : 0x0001 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : 'TV ' Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : 0 (TV) Primary Device Type : TV Logical Address Type : TV All Device Types : TV RC TV Profile : None Device Features :
None
Initial Event: State Change: PA: 0.0.0.0, LA mask: 0x0001, Conn Info: no
Received from Unregistered to TV (15 to 0): IMAGE_VIEW_ON (0x04) Received from Unregistered to TV (15 to 0): IMAGE_VIEW_ON (0x04)
Let me know what you think,
Maxime
Changes from v1:
- Removed the irqchip patch in favor of a select in mach-bcm
- Fixed HDMI1 interrupt numbers
- Removed redundant call to drm_connector_update_edid_property
- Fixed the condition in vc4_hdmi_connector_detect
- Added the tags
- Rebased on top of drm-misc-next-2021-01-06
Dom Cobley (5):
drm/vc4: hdmi: Move hdmi reset to bind
drm/vc4: hdmi: Fix register offset with longer CEC messages drm/vc4: hdmi: Fix up CEC registers
drm/vc4: hdmi: Restore cec physical address on reconnect drm/vc4: hdmi: Remove cec_available flag
Maxime Ripard (10):
ARM: bcm: Select BRCMSTB_L2_IRQ for bcm2835
drm/vc4: hdmi: Compute the CEC clock divider from the clock rate drm/vc4: hdmi: Update the CEC clock divider on HSM rate change drm/vc4: hdmi: Introduce a CEC clock
drm/vc4: hdmi: Split the interrupt handlers
drm/vc4: hdmi: Support BCM2711 CEC interrupt setup drm/vc4: hdmi: Don't register the CEC adapter if there's no interrupts
dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
ARM: dts: bcm2711: Add the BSC interrupt controller
ARM: dts: bcm2711: Add the CEC interrupt controller
.../bindings/display/brcm,bcm2711-hdmi.yaml | 20 +- arch/arm/boot/dts/bcm2711.dtsi | 30 +++ arch/arm/mach-bcm/Kconfig | 1 + arch/arm64/Kconfig.platforms | 1 + drivers/gpu/drm/vc4/vc4_hdmi.c | 223 ++++++++++++++---- drivers/gpu/drm/vc4/vc4_hdmi.h | 11 +- drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 4 +- 7 files changed, 234 insertions(+), 56 deletions(-)
Signature · 1 line
2.29.2
PATCH v2 1/15 ARM: bcm: Select BRCMSTB_L2_IRQ for bcm2835
The BCM2711 has a number of instances of interrupt controllers handled by the driver behind the BRCMSTB_L2_IRQ Kconfig option (irq-brcmstb-l2).
Let's select that driver as part of the ARCH_BCM2835 Kconfig option.
--- arch/arm/mach-bcm/Kconfig | 1 + arch/arm64/Kconfig.platforms | 1 + 2 files changed, 2 insertions(+)
arch/arm/mach-bcm/Kconfig +1 -0
@@ -161,6 +161,7 @@ config ARCH_BCM2835 select ARM_TIMER_SP804 select HAVE_ARM_ARCH_TIMER if ARCH_MULTI_V7 select BCM2835_TIMER + select BRCMSTB_L2_IRQ select PINCTRL select PINCTRL_BCM2835 select MFD_CORE
arch/arm64/Kconfig.platforms +1 -0
@@ -39,6 +39,7 @@ config ARCH_BCM2835 select ARM_AMBA select ARM_GIC select ARM_TIMER_SP804 + select BRCMSTB_L2_IRQ help This enables support for the Broadcom BCM2837 and BCM2711 SoC. These SoCs are used in the Raspberry Pi 3 and 4 devices.
Signature · 1 line
2.29.2
Re: [PATCH v2 01/15] ARM: bcm: Select BRCMSTB_L2_IRQ for bcm2835
Quoted 6 lines · Maxime Ripard
The BCM2711 has a number of instances of interrupt controllers handled by the driver behind the
BRCMSTB_L2_IRQKconfigoption (irq-brcmstb-l2).Let's select that driver as part of the
ARCH_BCM2835Kconfigoption.Signed-off-by Maxime Ripard <[email protected]>
Nicolas, I suppose you will be taking patches 1 and 14, 15 through the SoC pull request, right?
Signature · 1 line
Florian
Re: [PATCH v2 01/15] ARM: bcm: Select BRCMSTB_L2_IRQ for bcm2835
@Maxime it seems you forgot to CC me on the series :)
Quoted 5 lines · Florian Fainelli
Quoted 3 lines · Maxime Ripard
The BCM2711 has a number of instances of interrupt controllers handled by the driver behind the
BRCMSTB_L2_IRQKconfigoption (irq-brcmstb-l2).
Quoted 8 lines
Quoted 3 lines
Let's select that driver as part of the
ARCH_BCM2835Kconfigoption.Signed-off-by Maxime Ripard <[email protected]>Acked-by Florian Fainelli <[email protected]>Nicolas, I suppose you will be taking patches 1 and 14, 15 through the SoC pull request, right?
Yes, that's about right. But I think it'd be nice to wait a bit to see if RobH has something to say.
Regards,
Nicolas
PATCH v2 2/15 drm/vc4: hdmi: Move hdmi reset to bind
In reply to Maxime RipardFrom: Dom Cobley <[email protected]>
The hdmi reset got moved to a later point in the commit 9045e91a476b ("drm/vc4: hdmi: Add reset callback").
However, the reset now occurs after vc4_hdmi_cec_init and so tramples the setup of registers like HDMI_CEC_CNTRL_1
This only affects pi0-3 as on pi4 the cec registers are in a separate block
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +3 -3
@@ -779,9 +779,6 @@ static void vc4_hdmi_encoder_pre_crtc_configure(struct drm_encoder *encoder,return ; } -if (vc4_hdmi->variant->reset) - vc4_hdmi->variant->reset (vc4_hdmi); -if (vc4_hdmi->variant->phy_init) vc4_hdmi->variant->phy_init (vc4_hdmi, vc4_conn_state);
@@ -1874,6 +1871,9 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data) vc4_hdmi->disable_wifi_frequencies =of_property_read_bool (dev->of_node,"wifi-2.4ghz-coexistence" ); +if (vc4_hdmi->variant->reset) + vc4_hdmi->variant->reset (vc4_hdmi); +pm_runtime_enable (dev);drm_simple_encoder_init (drm, encoder,DRM_MODE_ENCODER_TMDS );
Signature · 1 line
2.29.2
PATCH v2 3/15 drm/vc4: hdmi: Fix register offset with longer CEC messages
In reply to Maxime RipardFrom: Dom Cobley <[email protected]>
The code prior to 311e305fdb4e ("drm/vc4: hdmi: Implement a register layout abstraction") was relying on the fact that the register offset was incremented by 4 for each readl call. That worked since the register width is 4 bytes.
However, since that commit the HDMI_READ macro is now taking an enum, and the offset doesn't increment by 4 but 1 now. Divide the index by 4 to fix this.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +15 -2
@@ -1443,13 +1443,20 @@ static irqreturn_t vc4_cec_irq_handler_thread(int irq, void *priv)static void vc4_cec_read_msg (struct vc4_hdmi *vc4_hdmi,u32 cntrl1) { +struct drm_device *dev = vc4_hdmi->connector.dev;struct cec_msg *msg = &vc4_hdmi->cec_rx_msg;unsigned int i; msg->len =1 + ((cntrl1 &VC4_HDMI_CEC_REC_WRD_CNT_MASK ) >>VC4_HDMI_CEC_REC_WRD_CNT_SHIFT ); + +if (msg->len >16 ) { +drm_err (dev,"Attempting to read too much data (%d)\n" , msg->len); +return ; + } +for (i =0 ; i < msg->len; i +=4 ) { -u32 val =HDMI_READ (HDMI_CEC_RX_DATA_1 + i); +u32 val =HDMI_READ (HDMI_CEC_RX_DATA_1 + (i >>2 )); msg->msg[i] = val &0xff ; msg->msg[i +1 ] = (val >>8 ) &0xff ;
@@ -1542,11 +1549,17 @@ static int vc4_hdmi_cec_adap_transmit(struct cec_adapter *adap, u8 attempts, u32 signal_free_time, struct cec_msg *msg) { struct vc4_hdmi *vc4_hdmi = cec_get_drvdata(adap); +struct drm_device *dev = vc4_hdmi->connector.dev;u32 val;unsigned int i; +if (msg->len >16 ) { +drm_err (dev,"Attempting to transmit too much data (%d)\n" , msg->len); +return -ENOMEM ; + } + for (i = 0; i < msg->len; i += 4) - HDMI_WRITE(HDMI_CEC_TX_DATA_1 + i, + HDMI_WRITE(HDMI_CEC_TX_DATA_1 + (i >> 2), (msg->msg[i]) | (msg->msg[i + 1] << 8) | (msg->msg[i + 2] << 16) |
Signature · 1 line
2.29.2
PATCH v2 4/15 drm/vc4: hdmi: Fix up CEC registers
In reply to Maxime RipardFrom: Dom Cobley <[email protected]>
The commit 311e305fdb4e ("drm/vc4: hdmi: Implement a register layout abstraction") forgot one CEC register, and made a copy and paste mistake for another one. Fix those mistakes.
--- drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/gpu/drm/vc4/vc4_hdmi_regs.h +3 -1
@@ -29,6 +29,7 @@ enum vc4_hdmi_field {HDMI_CEC_CPU_MASK_SET ,HDMI_CEC_CPU_MASK_STATUS ,HDMI_CEC_CPU_STATUS , + HDMI_CEC_CPU_SET,/* * Transmit data, first byte is low byte of the 32-bit reg.
@@ -199,9 +200,10 @@ static const struct vc4_hdmi_register __maybe_unused vc4_hdmi_fields[] = {VC4_HDMI_REG (HDMI_TX_PHY_RESET_CTL ,0x02c0 ),VC4_HDMI_REG (HDMI_TX_PHY_CTL_0 ,0x02c4 ),VC4_HDMI_REG (HDMI_CEC_CPU_STATUS ,0x0340 ), +VC4_HDMI_REG (HDMI_CEC_CPU_SET ,0x0344 ),VC4_HDMI_REG (HDMI_CEC_CPU_CLEAR ,0x0348 ),VC4_HDMI_REG (HDMI_CEC_CPU_MASK_STATUS ,0x034c ), -VC4_HDMI_REG (HDMI_CEC_CPU_MASK_SET ,0x034c ), +VC4_HDMI_REG (HDMI_CEC_CPU_MASK_SET ,0x0350 ),VC4_HDMI_REG (HDMI_CEC_CPU_MASK_CLEAR ,0x0354 ), VC4_HDMI_REG(HDMI_RAM_PACKET_START, 0x0400), };
Signature · 1 line
2.29.2
PATCH v2 5/15 drm/vc4: hdmi: Restore cec physical address on reconnect
In reply to Maxime RipardFrom: Dom Cobley <[email protected]>
Currently we call cec_phys_addr_invalidate on a hotplug deassert. That may be due to a TV power cycling, or an AVR being switched on (and switching edid).
This makes CEC unusable since our controller wouldn't have a physical address anymore.
Set it back up again on the hotplug assert.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 24 ++++++++++++++++++------ 1 file changed, 18 insertions(+), 6 deletions(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +18 -6
@@ -136,20 +136,32 @@ static enum drm_connector_status vc4_hdmi_connector_detect(struct drm_connector *connector, bool force) {struct vc4_hdmi *vc4_hdmi =connector_to_vc4_hdmi (connector); +bool connected = false;if (vc4_hdmi->hpd_gpio) {if (gpio_get_value_cansleep (vc4_hdmi->hpd_gpio) ^ vc4_hdmi->hpd_active_low) -return connector_status_connected; -cec_phys_addr_invalidate (vc4_hdmi->cec_adap); -return connector_status_disconnected; + connected = true; + }else if (drm_probe_ddc (vc4_hdmi->ddc)) { + connected = true; + }else if (HDMI_READ (HDMI_HOTPLUG ) &VC4_HDMI_HOTPLUG_CONNECTED ) { + connected = true; } -if (drm_probe_ddc (vc4_hdmi->ddc)) -return connector_status_connected; +if (connected) { +if (connector->status != connector_status_connected) { +struct edid *edid =drm_get_edid (connector, vc4_hdmi->ddc); + +if (edid) { +cec_s_phys_addr_from_edid (vc4_hdmi->cec_adap, edid); + vc4_hdmi->encoder.hdmi_monitor =drm_detect_hdmi_monitor (edid); +kfree (edid); + } + } -if (HDMI_READ (HDMI_HOTPLUG ) &VC4_HDMI_HOTPLUG_CONNECTED )return connector_status_connected; + } +cec_phys_addr_invalidate (vc4_hdmi->cec_adap);return connector_status_disconnected; }
Signature · 1 line
2.29.2
Re: [PATCH v2 05/15] drm/vc4: hdmi: Restore cec physical address on reconnect
Hi Maxime
Sorry for the slow reply on these patches.
Quoted 7 lines · Maxime Ripard
From: Dom Cobley <[email protected]>
Currently we call
cec_phys_addr_invalidateon a hotplug deassert. That may be due to a TV power cycling, or an AVR being switched on (and switching edid).
Quoted 8 lines
This makes CEC unusable since our controller wouldn't have a physical address anymore.
Set it back up again on the hotplug assert.
Fixes 15b4511a4af6 ("drm/vc4: add HDMI CEC support")Signed-off-by Dom Cobley <[email protected]>Signed-off-by Maxime Ripard <[email protected]>
I follow the logic, and trust Dom that it works, but I don't know if that is the correct thing within CEC.
Ideally Hans will comment as the original author of the CEC code - I believe he's testing the series anyway.
Quoted 48 lines
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 24 ++++++++++++++++++------ 1 file changed, 18 insertions(+), 6 deletions(-)drivers/gpu/drm/vc4/vc4_hdmi.c +18
-7@@ -136,20 +136,32 @@ static enum drm_connector_status vc4_hdmi_connector_detect(struct drm_connector *connector, bool force) {struct vc4_hdmi *vc4_hdmi =connector_to_vc4_hdmi (connector); +bool connected = false;if (vc4_hdmi->hpd_gpio) {if (gpio_get_value_cansleep (vc4_hdmi->hpd_gpio) ^ vc4_hdmi->hpd_active_low) -return connector_status_connected; -cec_phys_addr_invalidate (vc4_hdmi->cec_adap); -return connector_status_disconnected; + connected = true; + }else if (drm_probe_ddc (vc4_hdmi->ddc)) { + connected = true; + }else if (HDMI_READ (HDMI_HOTPLUG ) &VC4_HDMI_HOTPLUG_CONNECTED ) { + connected = true; } -if (drm_probe_ddc (vc4_hdmi->ddc)) -return connector_status_connected; +if (connected) { +if (connector->status != connector_status_connected) { +struct edid *edid =drm_get_edid (connector, vc4_hdmi->ddc); + +if (edid) { +cec_s_phys_addr_from_edid (vc4_hdmi->cec_adap, edid); + vc4_hdmi->encoder.hdmi_monitor =drm_detect_hdmi_monitor (edid); +kfree (edid); + } + } -if (HDMI_READ (HDMI_HOTPLUG ) &VC4_HDMI_HOTPLUG_CONNECTED )return connector_status_connected; + } +cec_phys_addr_invalidate (vc4_hdmi->cec_adap);return connector_status_disconnected; } --
Quoted 2 lines
2.29.2
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v2 6/15 drm/vc4: hdmi: Compute the CEC clock divider from the clock rate
In reply to Maxime RipardThe CEC clock divider needs to output a frequency of 40kHz from the HSM rate on the BCM2835. The driver used to have a fixed frequency for it, but that changed for the BCM2711 and we now need to compute it dynamically to maintain the proper rate.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +3 -1
@@ -1598,6 +1598,7 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi) {struct cec_connector_info conn_info;struct platform_device *pdev = vc4_hdmi->pdev; +u16 clk_cnt;u32 value;int ret;
@@ -1623,8 +1624,9 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi)* divider: the hsm_clock rate and this divider setting will * give a 40 kHz CEC clock. */ + clk_cnt =clk_get_rate (vc4_hdmi->hsm_clock) /CEC_CLOCK_FREQ ; value |=VC4_HDMI_CEC_ADDR_MASK | - (4091 <<VC4_HDMI_CEC_DIV_CLK_CNT_SHIFT ); + (clk_cnt <<VC4_HDMI_CEC_DIV_CLK_CNT_SHIFT );HDMI_WRITE (HDMI_CEC_CNTRL_1 , value); ret = devm_request_threaded_irq(&pdev->dev, platform_get_irq(pdev, 0), vc4_cec_irq_handler,
Signature · 7 lines
2.29.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v2 7/15 drm/vc4: hdmi: Update the CEC clock divider on HSM rate change
In reply to Maxime RipardAs part of the enable sequence we might change the HSM clock rate if the pixel rate is different than the one we were already dealing with.
On the BCM2835 however, the CEC clock derives from the HSM clock so any rate change will need to be reflected in the CEC clock divider to output 40kHz.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 39 +++++++++++++++++++++++++--------- 1 file changed, 29 insertions(+), 10 deletions(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +29 -10
@@ -132,6 +132,27 @@ static void vc5_hdmi_reset(struct vc4_hdmi *vc4_hdmi) HDMI_READ(HDMI_CLOCK_STOP) | VC4_DVP_HT_CLOCK_STOP_PIXEL); } +#ifdef CONFIG_DRM_VC4_HDMI_CEC +static void vc4_hdmi_cec_update_clk_div (struct vc4_hdmi *vc4_hdmi) +{ +u16 clk_cnt; +u32 value; + + value =HDMI_READ (HDMI_CEC_CNTRL_1 ); + value &= ~VC4_HDMI_CEC_DIV_CLK_CNT_MASK ; + +/* +* Set the clock divider: the hsm_clock rate and this divider +* setting will give a 40 kHz CEC clock. +*/ + clk_cnt =clk_get_rate (vc4_hdmi->hsm_clock) /CEC_CLOCK_FREQ ; + value |= clk_cnt <<VC4_HDMI_CEC_DIV_CLK_CNT_SHIFT ; +HDMI_WRITE (HDMI_CEC_CNTRL_1 , value); +} +#else +static void vc4_hdmi_cec_update_clk_div (struct vc4_hdmi *vc4_hdmi) {} +#endif +static enum drm_connector_status vc4_hdmi_connector_detect (struct drm_connector *connector,bool force) {
@@ -770,6 +791,8 @@ static void vc4_hdmi_encoder_pre_crtc_configure(struct drm_encoder *encoder,return ; } +vc4_hdmi_cec_update_clk_div (vc4_hdmi); +/* * FIXME: When the pixel freq is 594MHz (4k60), this needs to be setup * at 300MHz.
@@ -1598,7 +1621,6 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi) {struct cec_connector_info conn_info;struct platform_device *pdev = vc4_hdmi->pdev; -u16 clk_cnt;u32 value;int ret;
@@ -1617,17 +1639,14 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi)cec_s_conn_info (vc4_hdmi->cec_adap, &conn_info);HDMI_WRITE (HDMI_CEC_CPU_MASK_SET ,0xffffffff ); + value =HDMI_READ (HDMI_CEC_CNTRL_1 ); - value &= ~VC4_HDMI_CEC_DIV_CLK_CNT_MASK ; -/* -* Set the logical address to Unregistered and set the clock -* divider: the hsm_clock rate and this divider setting will -* give a 40 kHz CEC clock. -*/ - clk_cnt =clk_get_rate (vc4_hdmi->hsm_clock) /CEC_CLOCK_FREQ ; - value |=VC4_HDMI_CEC_ADDR_MASK | - (clk_cnt <<VC4_HDMI_CEC_DIV_CLK_CNT_SHIFT ); +/* Set the logical address to Unregistered */ + value |=VC4_HDMI_CEC_ADDR_MASK ;HDMI_WRITE (HDMI_CEC_CNTRL_1 , value); + +vc4_hdmi_cec_update_clk_div (vc4_hdmi); + ret = devm_request_threaded_irq(&pdev->dev, platform_get_irq(pdev, 0), vc4_cec_irq_handler, vc4_cec_irq_handler_thread, 0,
Signature · 1 line
2.29.2
PATCH v2 8/15 drm/vc4: hdmi: Introduce a CEC clock
In reply to Maxime RipardWhile the BCM2835 had the CEC clock derived from the HSM clock, the BCM2711 has a dedicated parent clock for it.
Let's introduce a separate clock for it so that we can handle both cases.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 9 ++++++++- drivers/gpu/drm/vc4/vc4_hdmi.h | 1 + 2 files changed, 9 insertions(+), 1 deletion(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +8 -1
@@ -145,7 +145,7 @@ static void vc4_hdmi_cec_update_clk_div(struct vc4_hdmi *vc4_hdmi)* Set the clock divider: the hsm_clock rate and this divider * setting will give a 40 kHz CEC clock. */ - clk_cnt =clk_get_rate (vc4_hdmi->hsm_clock) /CEC_CLOCK_FREQ ; + clk_cnt =clk_get_rate (vc4_hdmi->cec_clock) /CEC_CLOCK_FREQ ; value |= clk_cnt <<VC4_HDMI_CEC_DIV_CLK_CNT_SHIFT ;HDMI_WRITE (HDMI_CEC_CNTRL_1 , value); }
@@ -1752,6 +1752,7 @@ static int vc4_hdmi_init_resources(struct vc4_hdmi *vc4_hdmi)return PTR_ERR (vc4_hdmi->hsm_clock); } vc4_hdmi->audio_clock = vc4_hdmi->hsm_clock; + vc4_hdmi->cec_clock = vc4_hdmi->hsm_clock;return 0 ; }
@@ -1845,6 +1846,12 @@ static int vc5_hdmi_init_resources(struct vc4_hdmi *vc4_hdmi)return PTR_ERR (vc4_hdmi->audio_clock); } + vc4_hdmi->cec_clock =devm_clk_get (dev,"cec" ); +if (IS_ERR (vc4_hdmi->cec_clock)) { +DRM_ERROR ("Failed to get CEC clock\n" ); +return PTR_ERR (vc4_hdmi->cec_clock); + } + vc4_hdmi->reset =devm_reset_control_get (dev,NULL );if (IS_ERR (vc4_hdmi->reset)) {DRM_ERROR ("Failed to get HDMI reset line\n" );
drivers/gpu/drm/vc4/vc4_hdmi.h +1 -0
@@ -155,6 +155,7 @@ struct vc4_hdmi {bool cec_tx_ok;bool cec_irq_was_rx; +struct clk *cec_clock;struct clk *pixel_clock;struct clk *hsm_clock;struct clk *audio_clock;
Signature · 1 line
2.29.2
PATCH v2 9/15 drm/vc4: hdmi: Split the interrupt handlers
In reply to Maxime RipardThe BCM2711 has two different interrupt sources to transmit and receive CEC messages, provided through an external interrupt chip shared between the two HDMI interrupt controllers.
The rest of the CEC controller is identical though so we need to change a bit the code organisation to share the code as much as possible, yet still allowing to register independant handlers.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 86 +++++++++++++++++++++++++--------- 1 file changed, 65 insertions(+), 21 deletions(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +65 -21
@@ -1454,15 +1454,22 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *vc4_hdmi) }#ifdef CONFIG_DRM_VC4_HDMI_CEC -static irqreturn_t vc4_cec_irq_handler_thread (int irq,void *priv) +static irqreturn_t vc4_cec_irq_handler_rx_thread (int irq,void *priv) {struct vc4_hdmi *vc4_hdmi = priv; -if (vc4_hdmi->cec_irq_was_rx) { -if (vc4_hdmi->cec_rx_msg.len) -cec_received_msg (vc4_hdmi->cec_adap, - &vc4_hdmi->cec_rx_msg); - }else if (vc4_hdmi->cec_tx_ok) { +if (vc4_hdmi->cec_rx_msg.len) +cec_received_msg (vc4_hdmi->cec_adap, + &vc4_hdmi->cec_rx_msg); + +return IRQ_HANDLED ; +} + +static irqreturn_t vc4_cec_irq_handler_tx_thread (int irq,void *priv) +{ +struct vc4_hdmi *vc4_hdmi = priv; + +if (vc4_hdmi->cec_tx_ok) {cec_transmit_done (vc4_hdmi->cec_adap,CEC_TX_STATUS_OK ,0 ,0 ,0 ,0 ); }else {
@@ -1476,6 +1483,19 @@ static irqreturn_t vc4_cec_irq_handler_thread(int irq, void *priv)return IRQ_HANDLED ; } +static irqreturn_t vc4_cec_irq_handler_thread (int irq,void *priv) +{ +struct vc4_hdmi *vc4_hdmi = priv; +irqreturn_t ret; + +if (vc4_hdmi->cec_irq_was_rx) + ret =vc4_cec_irq_handler_rx_thread (irq, priv); +else + ret =vc4_cec_irq_handler_tx_thread (irq, priv); + +return ret; +} +static void vc4_cec_read_msg (struct vc4_hdmi *vc4_hdmi,u32 cntrl1) {struct drm_device *dev = vc4_hdmi->connector.dev;
@@ -1500,31 +1520,55 @@ static void vc4_cec_read_msg(struct vc4_hdmi *vc4_hdmi, u32 cntrl1) } } +static irqreturn_t vc4_cec_irq_handler_tx_bare (int irq,void *priv) +{ +struct vc4_hdmi *vc4_hdmi = priv; +u32 cntrl1; + + cntrl1 =HDMI_READ (HDMI_CEC_CNTRL_1 ); + vc4_hdmi->cec_tx_ok = cntrl1 &VC4_HDMI_CEC_TX_STATUS_GOOD ; + cntrl1 &= ~VC4_HDMI_CEC_START_XMIT_BEGIN ; +HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); + +return IRQ_WAKE_THREAD ; +} + +static irqreturn_t vc4_cec_irq_handler_rx_bare (int irq,void *priv) +{ +struct vc4_hdmi *vc4_hdmi = priv; +u32 cntrl1; + + vc4_hdmi->cec_rx_msg.len =0 ; + cntrl1 =HDMI_READ (HDMI_CEC_CNTRL_1 ); +vc4_cec_read_msg (vc4_hdmi, cntrl1); + cntrl1 |=VC4_HDMI_CEC_CLEAR_RECEIVE_OFF ; +HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); + cntrl1 &= ~VC4_HDMI_CEC_CLEAR_RECEIVE_OFF ; + +HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); + +return IRQ_WAKE_THREAD ; +} +static irqreturn_t vc4_cec_irq_handler (int irq,void *priv) {struct vc4_hdmi *vc4_hdmi = priv;u32 stat =HDMI_READ (HDMI_CEC_CPU_STATUS ); -u32 cntrl1, cntrl5; +irqreturn_t ret; +u32 cntrl5;if (!(stat &VC4_HDMI_CPU_CEC ))return IRQ_NONE ; - vc4_hdmi->cec_rx_msg.len =0 ; - cntrl1 =HDMI_READ (HDMI_CEC_CNTRL_1 ); + cntrl5 =HDMI_READ (HDMI_CEC_CNTRL_5 ); vc4_hdmi->cec_irq_was_rx = cntrl5 &VC4_HDMI_CEC_RX_CEC_INT ; -if (vc4_hdmi->cec_irq_was_rx) { -vc4_cec_read_msg (vc4_hdmi, cntrl1); - cntrl1 |=VC4_HDMI_CEC_CLEAR_RECEIVE_OFF ; -HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); - cntrl1 &= ~VC4_HDMI_CEC_CLEAR_RECEIVE_OFF ; - }else { - vc4_hdmi->cec_tx_ok = cntrl1 &VC4_HDMI_CEC_TX_STATUS_GOOD ; - cntrl1 &= ~VC4_HDMI_CEC_START_XMIT_BEGIN ; - } -HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); +if (vc4_hdmi->cec_irq_was_rx) + ret =vc4_cec_irq_handler_rx_bare (irq, priv); +else + ret =vc4_cec_irq_handler_tx_bare (irq, priv); +HDMI_WRITE (HDMI_CEC_CPU_CLEAR ,VC4_HDMI_CPU_CEC ); - -return IRQ_WAKE_THREAD ; +return ret; }static int vc4_hdmi_cec_adap_enable (struct cec_adapter *adap,bool enable)
Signature · 1 line
2.29.2
Re: [PATCH v2 09/15] drm/vc4: hdmi: Split the interrupt handlers
Hi Maxime
Quoted 8 lines · Maxime Ripard
The BCM2711 has two different interrupt sources to transmit and receive CEC messages, provided through an external interrupt chip shared between the two HDMI interrupt controllers.
The rest of the CEC controller is identical though so we need to change a bit the code organisation to share the code as much as possible, yet still allowing to register independant handlers.
s/independant/independent
Quoted 2 lines
Signed-off-by Maxime Ripard <[email protected]>
With that
Quoted 129 lines
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 86 +++++++++++++++++++++++++--------- 1 file changed, 65 insertions(+), 21 deletions(-)drivers/gpu/drm/vc4/vc4_hdmi.c +65
-22@@ -1454,15 +1454,22 @@ static int vc4_hdmi_audio_init(struct vc4_hdmi *vc4_hdmi) }#ifdef CONFIG_DRM_VC4_HDMI_CEC -static irqreturn_t vc4_cec_irq_handler_thread (int irq,void *priv) +static irqreturn_t vc4_cec_irq_handler_rx_thread (int irq,void *priv) {struct vc4_hdmi *vc4_hdmi = priv; -if (vc4_hdmi->cec_irq_was_rx) { -if (vc4_hdmi->cec_rx_msg.len) -cec_received_msg (vc4_hdmi->cec_adap, - &vc4_hdmi->cec_rx_msg); - }else if (vc4_hdmi->cec_tx_ok) { +if (vc4_hdmi->cec_rx_msg.len) +cec_received_msg (vc4_hdmi->cec_adap, + &vc4_hdmi->cec_rx_msg); + +return IRQ_HANDLED ; +} + +static irqreturn_t vc4_cec_irq_handler_tx_thread (int irq,void *priv) +{ +struct vc4_hdmi *vc4_hdmi = priv; + +if (vc4_hdmi->cec_tx_ok) {cec_transmit_done (vc4_hdmi->cec_adap,CEC_TX_STATUS_OK ,0 ,0 ,0 ,0 ); }else {@@ -1476,6 +1483,19 @@ static irqreturn_t vc4_cec_irq_handler_thread(int irq, void *priv)return IRQ_HANDLED ; } +static irqreturn_t vc4_cec_irq_handler_thread (int irq,void *priv) +{ +struct vc4_hdmi *vc4_hdmi = priv; +irqreturn_t ret; + +if (vc4_hdmi->cec_irq_was_rx) + ret =vc4_cec_irq_handler_rx_thread (irq, priv); +else + ret =vc4_cec_irq_handler_tx_thread (irq, priv); + +return ret; +} +static void vc4_cec_read_msg (struct vc4_hdmi *vc4_hdmi,u32 cntrl1) {struct drm_device *dev = vc4_hdmi->connector.dev;@@ -1500,31 +1520,55 @@ static void vc4_cec_read_msg(struct vc4_hdmi *vc4_hdmi, u32 cntrl1) } } +static irqreturn_t vc4_cec_irq_handler_tx_bare (int irq,void *priv) +{ +struct vc4_hdmi *vc4_hdmi = priv; +u32 cntrl1; + + cntrl1 =HDMI_READ (HDMI_CEC_CNTRL_1 ); + vc4_hdmi->cec_tx_ok = cntrl1 &VC4_HDMI_CEC_TX_STATUS_GOOD ; + cntrl1 &= ~VC4_HDMI_CEC_START_XMIT_BEGIN ; +HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); + +return IRQ_WAKE_THREAD ; +} + +static irqreturn_t vc4_cec_irq_handler_rx_bare (int irq,void *priv) +{ +struct vc4_hdmi *vc4_hdmi = priv; +u32 cntrl1; + + vc4_hdmi->cec_rx_msg.len =0 ; + cntrl1 =HDMI_READ (HDMI_CEC_CNTRL_1 ); +vc4_cec_read_msg (vc4_hdmi, cntrl1); + cntrl1 |=VC4_HDMI_CEC_CLEAR_RECEIVE_OFF ; +HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); + cntrl1 &= ~VC4_HDMI_CEC_CLEAR_RECEIVE_OFF ; + +HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); + +return IRQ_WAKE_THREAD ; +} +static irqreturn_t vc4_cec_irq_handler (int irq,void *priv) {struct vc4_hdmi *vc4_hdmi = priv;u32 stat =HDMI_READ (HDMI_CEC_CPU_STATUS ); -u32 cntrl1, cntrl5; +irqreturn_t ret; +u32 cntrl5;if (!(stat &VC4_HDMI_CPU_CEC ))return IRQ_NONE ; - vc4_hdmi->cec_rx_msg.len =0 ; - cntrl1 =HDMI_READ (HDMI_CEC_CNTRL_1 ); + cntrl5 =HDMI_READ (HDMI_CEC_CNTRL_5 ); vc4_hdmi->cec_irq_was_rx = cntrl5 &VC4_HDMI_CEC_RX_CEC_INT ; -if (vc4_hdmi->cec_irq_was_rx) { -vc4_cec_read_msg (vc4_hdmi, cntrl1); - cntrl1 |=VC4_HDMI_CEC_CLEAR_RECEIVE_OFF ; -HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); - cntrl1 &= ~VC4_HDMI_CEC_CLEAR_RECEIVE_OFF ; - }else { - vc4_hdmi->cec_tx_ok = cntrl1 &VC4_HDMI_CEC_TX_STATUS_GOOD ; - cntrl1 &= ~VC4_HDMI_CEC_START_XMIT_BEGIN ; - } -HDMI_WRITE (HDMI_CEC_CNTRL_1 , cntrl1); +if (vc4_hdmi->cec_irq_was_rx) + ret =vc4_cec_irq_handler_rx_bare (irq, priv); +else + ret =vc4_cec_irq_handler_tx_bare (irq, priv); +HDMI_WRITE (HDMI_CEC_CPU_CLEAR ,VC4_HDMI_CPU_CEC ); - -return IRQ_WAKE_THREAD ; +return ret; }static int vc4_hdmi_cec_adap_enable (struct cec_adapter *adap,bool enable) --
Quoted 2 lines
2.29.2
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v2 10/15 drm/vc4: hdmi: Support BCM2711 CEC interrupt setup
In reply to Maxime RipardThe HDMI controller found in the BCM2711 has an external interrupt controller for the CEC and hotplug interrupt shared between the two instances.
Let's add a variant flag to register a single interrupt handler and deals with the interrupt handler setup, or two interrupt handlers relying on an external irqchip.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 42 ++++++++++++++++++++++++++-------- drivers/gpu/drm/vc4/vc4_hdmi.h | 7 ++++++ 2 files changed, 39 insertions(+), 10 deletions(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +32 -10
@@ -1605,9 +1605,11 @@ static int vc4_hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable) ((3600 / usecs) <<VC4_HDMI_CEC_CNT_TO_3600_US_SHIFT ) | ((3500 / usecs) << VC4_HDMI_CEC_CNT_TO_3500_US_SHIFT)); -HDMI_WRITE (HDMI_CEC_CPU_MASK_CLEAR ,VC4_HDMI_CPU_CEC ); +if (!vc4_hdmi->variant->external_irq_controller) +HDMI_WRITE (HDMI_CEC_CPU_MASK_CLEAR ,VC4_HDMI_CPU_CEC ); }else { -HDMI_WRITE (HDMI_CEC_CPU_MASK_SET ,VC4_HDMI_CPU_CEC ); +if (!vc4_hdmi->variant->external_irq_controller) +HDMI_WRITE (HDMI_CEC_CPU_MASK_SET ,VC4_HDMI_CPU_CEC );HDMI_WRITE (HDMI_CEC_CNTRL_5 , val |VC4_HDMI_CEC_TX_SW_RESET |VC4_HDMI_CEC_RX_SW_RESET ); }
@@ -1682,8 +1684,6 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi)cec_fill_conn_info_from_drm (&conn_info, &vc4_hdmi->connector);cec_s_conn_info (vc4_hdmi->cec_adap, &conn_info); -HDMI_WRITE (HDMI_CEC_CPU_MASK_SET ,0xffffffff ); - value =HDMI_READ (HDMI_CEC_CNTRL_1 );/* Set the logical address to Unregistered */ value |=VC4_HDMI_CEC_ADDR_MASK ;
@@ -1691,12 +1691,32 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi)vc4_hdmi_cec_update_clk_div (vc4_hdmi); - ret =devm_request_threaded_irq (&pdev->dev,platform_get_irq (pdev,0 ), - vc4_cec_irq_handler, - vc4_cec_irq_handler_thread,0 , -"vc4 hdmi cec" , vc4_hdmi); -if (ret) - goto err_delete_cec_adap; +if (vc4_hdmi->variant->external_irq_controller) { + ret =devm_request_threaded_irq (&pdev->dev, +platform_get_irq_byname (pdev,"cec-rx" ), + vc4_cec_irq_handler_rx_bare, + vc4_cec_irq_handler_rx_thread,0 , +"vc4 hdmi cec rx" , vc4_hdmi); +if (ret) + goto err_delete_cec_adap; + + ret =devm_request_threaded_irq (&pdev->dev, +platform_get_irq_byname (pdev,"cec-tx" ), + vc4_cec_irq_handler_tx_bare, + vc4_cec_irq_handler_tx_thread,0 , +"vc4 hdmi cec tx" , vc4_hdmi); +if (ret) + goto err_delete_cec_adap; + }else { +HDMI_WRITE (HDMI_CEC_CPU_MASK_SET ,0xffffffff ); + + ret =devm_request_threaded_irq (&pdev->dev,platform_get_irq (pdev,0 ), + vc4_cec_irq_handler, + vc4_cec_irq_handler_thread,0 , +"vc4 hdmi cec" , vc4_hdmi); +if (ret) + goto err_delete_cec_adap; + } ret =cec_register_adapter (vc4_hdmi->cec_adap, &pdev->dev);if (ret <0 )
@@ -2095,6 +2115,7 @@ static const struct vc4_hdmi_variant bcm2711_hdmi0_variant = { PHY_LANE_CK, }, .unsupported_odd_h_timings = true, + .external_irq_controller = true, .init_resources = vc5_hdmi_init_resources, .csc_setup = vc5_hdmi_csc_setup,
@@ -2121,6 +2142,7 @@ static const struct vc4_hdmi_variant bcm2711_hdmi1_variant = { PHY_LANE_2, }, .unsupported_odd_h_timings = true, + .external_irq_controller = true, .init_resources = vc5_hdmi_init_resources, .csc_setup = vc5_hdmi_csc_setup,
drivers/gpu/drm/vc4/vc4_hdmi.h +7 -0
@@ -64,6 +64,13 @@ struct vc4_hdmi_variant {/* The BCM2711 cannot deal with odd horizontal pixel timings */ bool unsupported_odd_h_timings; +/* +* The BCM2711 CEC/hotplug IRQ controller is shared between the +* two HDMI controllers, and we have a proper irqchip driver for +* it. +*/ +bool external_irq_controller; +/* Callback to get the resources (memory region, interrupts, * clocks, etc) for that variant. */
Signature · 1 line
2.29.2
Re: [PATCH v2 10/15] drm/vc4: hdmi: Support BCM2711 CEC interrupt setup
Hi Maxime
Quoted 10 lines · Maxime Ripard
The HDMI controller found in the BCM2711 has an external interrupt controller for the CEC and hotplug interrupt shared between the two instances.
Let's add a variant flag to register a single interrupt handler and deals with the interrupt handler setup, or two interrupt handlers relying on an external irqchip.
Signed-off-by Maxime Ripard <[email protected]>
Looks good
Quoted 106 lines
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 42 ++++++++++++++++++++++++++-------- drivers/gpu/drm/vc4/vc4_hdmi.h | 7 ++++++ 2 files changed, 39 insertions(+), 10 deletions(-)drivers/gpu/drm/vc4/vc4_hdmi.c +32
-10@@ -1605,9 +1605,11 @@ static int vc4_hdmi_cec_adap_enable(struct cec_adapter *adap, bool enable) ((3600 / usecs) <<VC4_HDMI_CEC_CNT_TO_3600_US_SHIFT ) | ((3500 / usecs) << VC4_HDMI_CEC_CNT_TO_3500_US_SHIFT)); -HDMI_WRITE (HDMI_CEC_CPU_MASK_CLEAR ,VC4_HDMI_CPU_CEC ); +if (!vc4_hdmi->variant->external_irq_controller) +HDMI_WRITE (HDMI_CEC_CPU_MASK_CLEAR ,VC4_HDMI_CPU_CEC ); }else { -HDMI_WRITE (HDMI_CEC_CPU_MASK_SET ,VC4_HDMI_CPU_CEC ); +if (!vc4_hdmi->variant->external_irq_controller) +HDMI_WRITE (HDMI_CEC_CPU_MASK_SET ,VC4_HDMI_CPU_CEC );HDMI_WRITE (HDMI_CEC_CNTRL_5 , val |VC4_HDMI_CEC_TX_SW_RESET |VC4_HDMI_CEC_RX_SW_RESET ); }@@ -1682,8 +1684,6 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi)cec_fill_conn_info_from_drm (&conn_info, &vc4_hdmi->connector);cec_s_conn_info (vc4_hdmi->cec_adap, &conn_info); -HDMI_WRITE (HDMI_CEC_CPU_MASK_SET ,0xffffffff ); - value =HDMI_READ (HDMI_CEC_CNTRL_1 );/* Set the logical address to Unregistered */ value |=VC4_HDMI_CEC_ADDR_MASK ;@@ -1691,12 +1691,32 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi)vc4_hdmi_cec_update_clk_div (vc4_hdmi); - ret =devm_request_threaded_irq (&pdev->dev,platform_get_irq (pdev,0 ), - vc4_cec_irq_handler, - vc4_cec_irq_handler_thread,0 , -"vc4 hdmi cec" , vc4_hdmi); -if (ret) - goto err_delete_cec_adap; +if (vc4_hdmi->variant->external_irq_controller) { + ret =devm_request_threaded_irq (&pdev->dev, +platform_get_irq_byname (pdev,"cec-rx" ), + vc4_cec_irq_handler_rx_bare, + vc4_cec_irq_handler_rx_thread,0 , +"vc4 hdmi cec rx" , vc4_hdmi); +if (ret) + goto err_delete_cec_adap; + + ret =devm_request_threaded_irq (&pdev->dev, +platform_get_irq_byname (pdev,"cec-tx" ), + vc4_cec_irq_handler_tx_bare, + vc4_cec_irq_handler_tx_thread,0 , +"vc4 hdmi cec tx" , vc4_hdmi); +if (ret) + goto err_delete_cec_adap; + }else { +HDMI_WRITE (HDMI_CEC_CPU_MASK_SET ,0xffffffff ); + + ret =devm_request_threaded_irq (&pdev->dev,platform_get_irq (pdev,0 ), + vc4_cec_irq_handler, + vc4_cec_irq_handler_thread,0 , +"vc4 hdmi cec" , vc4_hdmi); +if (ret) + goto err_delete_cec_adap; + } ret =cec_register_adapter (vc4_hdmi->cec_adap, &pdev->dev);if (ret <0 )@@ -2095,6 +2115,7 @@ static const struct vc4_hdmi_variant bcm2711_hdmi0_variant = { PHY_LANE_CK, }, .unsupported_odd_h_timings = true, + .external_irq_controller = true, .init_resources = vc5_hdmi_init_resources, .csc_setup = vc5_hdmi_csc_setup,@@ -2121,6 +2142,7 @@ static const struct vc4_hdmi_variant bcm2711_hdmi1_variant = { PHY_LANE_2, }, .unsupported_odd_h_timings = true, + .external_irq_controller = true, .init_resources = vc5_hdmi_init_resources, .csc_setup = vc5_hdmi_csc_setup,drivers/gpu/drm/vc4/vc4_hdmi.h +7
-1@@ -64,6 +64,13 @@ struct vc4_hdmi_variant {/* The BCM2711 cannot deal with odd horizontal pixel timings */ bool unsupported_odd_h_timings; +/* +* The BCM2711 CEC/hotplug IRQ controller is shared between the +* two HDMI controllers, and we have a proper irqchip driver for +* it. +*/ +bool external_irq_controller; +/* Callback to get the resources (memory region, interrupts, * clocks, etc) for that variant. */ --
Quoted 2 lines
2.29.2
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v2 11/15 drm/vc4: hdmi: Remove cec_available flag
In reply to Maxime RipardFrom: Dom Cobley <[email protected]>
Now that our HDMI controller supports CEC for the BCM2711, let's remove that flag.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 4 ---- drivers/gpu/drm/vc4/vc4_hdmi.h | 3 --- 2 files changed, 7 deletions(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +0 -4
@@ -1670,9 +1670,6 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi)u32 value;int ret; -if (!vc4_hdmi->variant->cec_available) -return 0 ; - vc4_hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops, vc4_hdmi, "vc4", CEC_CAP_DEFAULTS |
@@ -2086,7 +2083,6 @@ static const struct vc4_hdmi_variant bcm2835_variant = { .debugfs_name = "hdmi_regs", .card_name = "vc4-hdmi", .max_pixel_clock = 162000000, - .cec_available = true, .registers = vc4_hdmi_fields, .num_registers = ARRAY_SIZE(vc4_hdmi_fields),
drivers/gpu/drm/vc4/vc4_hdmi.h +0 -3
@@ -42,9 +42,6 @@ struct vc4_hdmi_variant {/* Filename to expose the registers in debugfs */ const char *debugfs_name; -/* Set to true when the CEC support is available */ -bool cec_available; -/* Maximum pixel clock supported by the controller (in Hz) */ unsigned long long max_pixel_clock;
Signature · 1 line
2.29.2
PATCH v2 12/15 drm/vc4: hdmi: Don't register the CEC adapter if there's no interrupts
In reply to Maxime RipardWe introduced the BCM2711 support to the vc4 HDMI controller with 5.10, but this was lacking any of the interrupts of the CEC controller so we have to deal with the backward compatibility.
Do so by simply ignoring the CEC setup if the DT doesn't have the interrupts property.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/gpu/drm/vc4/vc4_hdmi.c +6 -0
@@ -1667,9 +1667,15 @@ static int vc4_hdmi_cec_init(struct vc4_hdmi *vc4_hdmi) {struct cec_connector_info conn_info;struct platform_device *pdev = vc4_hdmi->pdev; +struct device *dev = &pdev->dev;u32 value;int ret; +if (!of_find_property (dev->of_node,"interrupts" ,NULL )) { +dev_warn (dev,"'interrupts' DT property is missing, no CEC\n" ); +return 0 ; + } + vc4_hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops, vc4_hdmi, "vc4", CEC_CAP_DEFAULTS |
Signature · 1 line
2.29.2
PATCH v2 13/15 dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
In reply to Maxime RipardThe CEC and hotplug interrupts were missing when that binding was introduced, let's add them in now that we've figured out how it works.
--- .../bindings/display/brcm,bcm2711-hdmi.yaml | 20 ++++++++++++++++++- 1 file changed, 19 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml +19 -1
@@ -53,6 +53,24 @@ properties: - const: audio - const: cec + interrupts: + items: + - description: CEC TX interrupt + - description: CEC RX interrupt + - description: CEC stuck at low interrupt + - description: Wake-up interrupt + - description: Hotplug connected interrupt + - description: Hotplug removed interrupt + + interrupt-names: + items: + - const: cec-tx + - const: cec-rx + - const: cec-low + - const: wakeup + - const: hpd-connected + - const: hpd-removed + ddc: allOf: - $ref: /schemas/types.yaml#/definitions/phandle
@@ -90,7 +108,7 @@ required: - resets - ddc -additionalProperties: false +unevaluatedProperties: false examples: - |
Signature · 1 line
2.29.2
Re: [PATCH v2 13/15] dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
Hi Maxime
Quoted 5 lines · Maxime Ripard
The CEC and hotplug interrupts were missing when that binding was introduced, let's add them in now that we've figured out how it works.
Signed-off-by Maxime Ripard <[email protected]>
Looks reasonable to me, but I'm not a DT bindings expert
Quoted 43 lines
--- .../bindings/display/brcm,bcm2711-hdmi.yaml | 20 ++++++++++++++++++- 1 file changed, 19 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml +19
-2@@ -53,6 +53,24 @@ properties: - const: audio - const: cec + interrupts: + items: + - description: CEC TX interrupt + - description: CEC RX interrupt + - description: CEC stuck at low interrupt + - description: Wake-up interrupt + - description: Hotplug connected interrupt + - description: Hotplug removed interrupt + + interrupt-names: + items: + - const: cec-tx + - const: cec-rx + - const: cec-low + - const: wakeup + - const: hpd-connected + - const: hpd-removed + ddc: allOf: - $ref: /schemas/types.yaml#/definitions/phandle@@ -90,7 +108,7 @@ required: - resets - ddc -additionalProperties: false +unevaluatedProperties: false examples: - | --
Quoted 2 lines
2.29.2
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Rob Herring
maintainerRe: [PATCH v2 13/15] dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
In reply to Maxime RipardQuoted 39 lines · Maxime Ripard
The CEC and hotplug interrupts were missing when that binding was introduced, let's add them in now that we've figured out how it works.
Signed-off-by Maxime Ripard <[email protected]>--- .../bindings/display/brcm,bcm2711-hdmi.yaml | 20 ++++++++++++++++++- 1 file changed, 19 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml +18
-0@@ -53,6 +53,24 @@ properties: - const: audio - const: cec + interrupts: + items: + - description: CEC TX interrupt + - description: CEC RX interrupt + - description: CEC stuck at low interrupt + - description: Wake-up interrupt + - description: Hotplug connected interrupt + - description: Hotplug removed interrupt + + interrupt-names: + items: + - const: cec-tx + - const: cec-rx + - const: cec-low + - const: wakeup + - const: hpd-connected + - const: hpd-removed + ddc: allOf: - $ref: /schemas/types.yaml#/definitions/phandle
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml required: · line 111
Quoted 5 lines
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml +1
-1@@ -90,7 +108,7 @@ required: - resets - ddc -additionalProperties: false +unevaluatedProperties: false
/builds/robherring/linux-dt-bindings/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml:
'additionalProperties' is a required property
And you missed the DT list, so no checks ran.
Rob
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Rob Herring
maintainerRe: [PATCH v2 13/15] dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
Quoted 44 lines · Rob Herring
Quoted 42 lines · Maxime Ripard
The CEC and hotplug interrupts were missing when that binding was introduced, let's add them in now that we've figured out how it works.
Signed-off-by Maxime Ripard <[email protected]>--- .../bindings/display/brcm,bcm2711-hdmi.yaml | 20 ++++++++++++++++++- 1 file changed, 19 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml +18
-0@@ -53,6 +53,24 @@ properties: - const: audio - const: cec + interrupts: + items: + - description: CEC TX interrupt + - description: CEC RX interrupt + - description: CEC stuck at low interrupt + - description: Wake-up interrupt + - description: Hotplug connected interrupt + - description: Hotplug removed interrupt + + interrupt-names: + items: + - const: cec-tx + - const: cec-rx + - const: cec-low + - const: wakeup + - const: hpd-connected + - const: hpd-removed + ddc: allOf: - $ref: /schemas/types.yaml#/definitions/phandle@@ -90,7 +108,7 @@ required: - resets - ddc
Quoted 7 lines
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml required: · line 111
Quoted 2 lines
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml +1
-1-additionalProperties: false +unevaluatedProperties: false/builds/robherring/linux-dt-bindings/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml:
'additionalProperties' is a required propertyAnd you missed the DT list, so no checks ran.
This is still failing in linux-next.
Rob
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v2 14/15 ARM: dts: bcm2711: Add the BSC interrupt controller
In reply to Maxime RipardThe BSC controllers used for the HDMI DDC have an interrupt controller shared between both instances. Let's add it to avoid polling.
--- arch/arm/boot/dts/bcm2711.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/arm/boot/dts/bcm2711.dtsi +12 -0
@@ -308,6 +308,14 @@ dvp: clock@7ef00000 { #reset-cells = <1>; }; + bsc_intr: interrupt-controller@7ef00040 { + compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; + reg = <0x7ef00040 0x30>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + }; + hdmi0: hdmi@7ef00700 { compatible = "brcm,bcm2711-hdmi0"; reg = <0x7ef00700 0x300>,
@@ -341,6 +349,8 @@ ddc0: i2c@7ef04500 { reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; reg-names = "bsc", "auto-i2c"; clock-frequency = <97500>; + interrupt-parent = <&bsc_intr>; + interrupts = <0>; status = "disabled"; };
@@ -377,6 +387,8 @@ ddc1: i2c@7ef09500 { reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>; reg-names = "bsc", "auto-i2c"; clock-frequency = <97500>; + interrupt-parent = <&bsc_intr>; + interrupts = <1>; status = "disabled"; }; };
Signature · 1 line
2.29.2
Dave Stevenson
maintainerRe: [PATCH v2 14/15] ARM: dts: bcm2711: Add the BSC interrupt controller
Hi Maxime
Quoted 3 lines · Maxime Ripard
The BSC controllers used for the HDMI DDC have an interrupt controller shared between both instances. Let's add it to avoid polling.
This seems to have unintended side effects.
GIC interrupt 117 is shared between the standard I2C controllers (i2c-bcm2835) and the l2-intc block handling the HDMI I2C interrupts.
Whilst i2c-bcm2835 requests the interrupt with IRQF_SHARED, that doesn't appear to be an option for l2-intc registering as an interrupt controller. i2c-bcm2835 therefore loses out and fails to register for the interrupt.
Is there an equivalent flag that an interrupt controller can add to say that the parent interrupt is shared? Is that even supported?
Thanks
Dave
Quoted 44 lines
Reviewed-by Florian Fainelli <[email protected]>Signed-off-by Maxime Ripard <[email protected]>--- arch/arm/boot/dts/bcm2711.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)arch/arm/boot/dts/bcm2711.dtsi +12
-1@@ -308,6 +308,14 @@ dvp: clock@7ef00000 { #reset-cells = <1>; }; + bsc_intr: interrupt-controller@7ef00040 { + compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; + reg = <0x7ef00040 0x30>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + }; + hdmi0: hdmi@7ef00700 { compatible = "brcm,bcm2711-hdmi0"; reg = <0x7ef00700 0x300>,@@ -341,6 +349,8 @@ ddc0: i2c@7ef04500 { reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; reg-names = "bsc", "auto-i2c"; clock-frequency = <97500>; + interrupt-parent = <&bsc_intr>; + interrupts = <0>; status = "disabled"; };@@ -377,6 +387,8 @@ ddc1: i2c@7ef09500 { reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>; reg-names = "bsc", "auto-i2c"; clock-frequency = <97500>; + interrupt-parent = <&bsc_intr>; + interrupts = <1>; status = "disabled"; }; }; --
Quoted 2 lines
2.29.2
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 14/15] ARM: dts: bcm2711: Add the BSC interrupt controller
Hi Dave,
Quoted 9 lines · Dave Stevenson
Quoted 3 lines · Maxime Ripard
The BSC controllers used for the HDMI DDC have an interrupt controller shared between both instances. Let's add it to avoid polling.
This seems to have unintended side effects.
GIC interrupt 117 is shared between the standard I2C controllers (i2c-bcm2835) and the l2-intc block handling the HDMI I2C interrupts.
Quoted 7 lines
Whilst i2c-bcm2835 requests the interrupt with
IRQF_SHARED, that doesn't appear to be an option for l2-intc registering as an interrupt controller. i2c-bcm2835 therefore loses out and fails to register for the interrupt.Is there an equivalent flag that an interrupt controller can add to say that the parent interrupt is shared? Is that even supported?
Indeed, it looks like setting an equivalent to IRQF_SHARED would be the solution, but I couldn't find anything that would allow us to in the irqchip code.
Marc, Thomas, is it something that is allowed?
Thanks!
Maxime
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 14/15] ARM: dts: bcm2711: Add the BSC interrupt controller
Hi Maxime,
Quoted 17 lines · Maxime Ripard
Hi Dave,
Quoted 14 lines · Dave Stevenson
Quoted 3 lines · Maxime Ripard
The BSC controllers used for the HDMI DDC have an interrupt controller shared between both instances. Let's add it to avoid polling.
This seems to have unintended side effects.
GIC interrupt 117 is shared between the standard I2C controllers (i2c-bcm2835) and the l2-intc block handling the HDMI I2C interrupts.Whilst i2c-bcm2835 requests the interrupt with
IRQF_SHARED, that doesn't appear to be an option for l2-intc registering as an interrupt controller. i2c-bcm2835 therefore loses out and fails to register for the interrupt.
Quoted 8 lines
Quoted 2 lines
Is there an equivalent flag that an interrupt controller can add to say that the parent interrupt is shared? Is that even supported?
Indeed, it looks like setting an equivalent to
IRQF_SHAREDwould be the solution, but I couldn't find anything that would allow us to in the irqchip code.Marc, Thomas, is it something that is allowed?
No, not really. That's because the chained handler is actually an interrupt flow, and not a normal handler. IRQF_SHARED acts at the wrong level for that.
I can see two possibilities:
- the l2-intc gets turned into a normal handler, and does the demux from there. Horrible stuff.
- the i2c controller gets parented to the l2c-int as a fake interrupt, and gets called from there. Horrible stuff.
Pick your poison... :-/
M.
Signature · 5 lines
Jazz is not dead. It just smells funny... _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Dave Stevenson
maintainerRe: [PATCH v2 14/15] ARM: dts: bcm2711: Add the BSC interrupt controller
Hi Marc.
Quoted 36 lines · Marc Zyngier
Hi Maxime,
Quoted 17 lines · Maxime Ripard
Hi Dave,
Quoted 14 lines · Dave Stevenson
Quoted 3 lines · Maxime Ripard
The BSC controllers used for the HDMI DDC have an interrupt controller shared between both instances. Let's add it to avoid polling.
This seems to have unintended side effects.
GIC interrupt 117 is shared between the standard I2C controllers (i2c-bcm2835) and the l2-intc block handling the HDMI I2C interrupts.Whilst i2c-bcm2835 requests the interrupt with
IRQF_SHARED, that doesn't appear to be an option for l2-intc registering as an interrupt controller. i2c-bcm2835 therefore loses out and fails to register for the interrupt.Quoted 8 lines
Quoted 2 lines
Is there an equivalent flag that an interrupt controller can add to say that the parent interrupt is shared? Is that even supported?
Indeed, it looks like setting an equivalent to
IRQF_SHAREDwould be the solution, but I couldn't find anything that would allow us to in the irqchip code.Marc, Thomas, is it something that is allowed?
No, not really. That's because the chained handler is actually an interrupt flow, and not a normal handler.
IRQF_SHAREDacts at the wrong level for that.I can see two possibilities:
Quoted 7 lines
- the l2-intc gets turned into a normal handler, and does the demux from there. Horrible stuff.
- the i2c controller gets parented to the l2c-int as a fake interrupt, and gets called from there. Horrible stuff.
Pick your poison... :-/
Thanks for the info.
Option 3 - remove l2-intc and drop back to polling the i2c-brcmstb blocks (which the driver supports anyway).
HDMI I2C generally isn't heavily used once displays are connected, so I'd be OK with that.
(We can keep the l2-intc that handles CEC and HPD as that is on a unique GIC interrupt).
Dave
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 14/15] ARM: dts: bcm2711: Add the BSC interrupt controller
Quoted 49 lines · Dave Stevenson
Hi Marc.
Quoted 36 lines · Marc Zyngier
Hi Maxime,
Quoted 17 lines · Maxime Ripard
Hi Dave,
Quoted 14 lines · Dave Stevenson
Quoted 3 lines · Maxime Ripard
The BSC controllers used for the HDMI DDC have an interrupt controller shared between both instances. Let's add it to avoid polling.
This seems to have unintended side effects.
GIC interrupt 117 is shared between the standard I2C controllers (i2c-bcm2835) and the l2-intc block handling the HDMI I2C interrupts.Whilst i2c-bcm2835 requests the interrupt with
IRQF_SHARED, that doesn't appear to be an option for l2-intc registering as an interrupt controller. i2c-bcm2835 therefore loses out and fails to register for the interrupt.Quoted 8 lines
Quoted 2 lines
Is there an equivalent flag that an interrupt controller can add to say that the parent interrupt is shared? Is that even supported?
Indeed, it looks like setting an equivalent to
IRQF_SHAREDwould be the solution, but I couldn't find anything that would allow us to in the irqchip code.Marc, Thomas, is it something that is allowed?
No, not really. That's because the chained handler is actually an interrupt flow, and not a normal handler.
IRQF_SHAREDacts at the wrong level for that.I can see two possibilities:
Quoted 7 lines
- the l2-intc gets turned into a normal handler, and does the demux from there. Horrible stuff.
- the i2c controller gets parented to the l2c-int as a fake interrupt, and gets called from there. Horrible stuff.
Pick your poison... :-/
Thanks for the info.
Quoted 7 lines
Option 3 - remove l2-intc and drop back to polling the i2c-brcmstb blocks (which the driver supports anyway).
HDMI I2C generally isn't heavily used once displays are connected, so I'd be OK with that.(We can keep the l2-intc that handles CEC and HPD as that is on a unique GIC interrupt).
Agreed, Maxime or Nicolas do you want me to send a revert of this patch?
Signature · 6 lines
Florian _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v2 14/15] ARM: dts: bcm2711: Add the BSC interrupt controller
Quoted 55 lines · Florian Fainelli
Quoted 54 lines · Dave Stevenson
Hi Marc.
Quoted 36 lines · Marc Zyngier
Hi Maxime,
Quoted 17 lines · Maxime Ripard
Hi Dave,
Quoted 14 lines · Dave Stevenson
Quoted 3 lines · Maxime Ripard
The BSC controllers used for the HDMI DDC have an interrupt controller shared between both instances. Let's add it to avoid polling.
This seems to have unintended side effects.
GIC interrupt 117 is shared between the standard I2C controllers (i2c-bcm2835) and the l2-intc block handling the HDMI I2C interrupts.Whilst i2c-bcm2835 requests the interrupt with
IRQF_SHARED, that doesn't appear to be an option for l2-intc registering as an interrupt controller. i2c-bcm2835 therefore loses out and fails to register for the interrupt.Quoted 8 lines
Quoted 2 lines
Is there an equivalent flag that an interrupt controller can add to say that the parent interrupt is shared? Is that even supported?
Indeed, it looks like setting an equivalent to
IRQF_SHAREDwould be the solution, but I couldn't find anything that would allow us to in the irqchip code.Marc, Thomas, is it something that is allowed?
No, not really. That's because the chained handler is actually an interrupt flow, and not a normal handler.
IRQF_SHAREDacts at the wrong level for that.I can see two possibilities:
Quoted 7 lines
- the l2-intc gets turned into a normal handler, and does the demux from there. Horrible stuff.
- the i2c controller gets parented to the l2c-int as a fake interrupt, and gets called from there. Horrible stuff.
Pick your poison... :-/
Thanks for the info.
Option 3 - remove l2-intc and drop back to polling the i2c-brcmstb blocks (which the driver supports anyway).
HDMI I2C generally isn't heavily used once displays are connected, so I'd be OK with that.
Quoted 4 lines
Quoted 2 lines
(We can keep the l2-intc that handles CEC and HPD as that is on a unique GIC interrupt).
Agreed, Maxime or Nicolas do you want me to send a revert of this patch?
Reverting seems the safe move, but I'll defer to whatever Maxime says.
Regards,
Nicolas
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 14/15] ARM: dts: bcm2711: Add the BSC interrupt controller
Quoted 56 lines · Nicolas Saenz Julienne
Quoted 55 lines · Florian Fainelli
Quoted 54 lines · Dave Stevenson
Hi Marc.
Quoted 36 lines · Marc Zyngier
Hi Maxime,
Quoted 17 lines · Maxime Ripard
Hi Dave,
Quoted 14 lines · Dave Stevenson
Quoted 3 lines · Maxime Ripard
The BSC controllers used for the HDMI DDC have an interrupt controller shared between both instances. Let's add it to avoid polling.
This seems to have unintended side effects.
GIC interrupt 117 is shared between the standard I2C controllers (i2c-bcm2835) and the l2-intc block handling the HDMI I2C interrupts.Whilst i2c-bcm2835 requests the interrupt with
IRQF_SHARED, that doesn't appear to be an option for l2-intc registering as an interrupt controller. i2c-bcm2835 therefore loses out and fails to register for the interrupt.Quoted 8 lines
Quoted 2 lines
Is there an equivalent flag that an interrupt controller can add to say that the parent interrupt is shared? Is that even supported?
Indeed, it looks like setting an equivalent to
IRQF_SHAREDwould be the solution, but I couldn't find anything that would allow us to in the irqchip code.Marc, Thomas, is it something that is allowed?
No, not really. That's because the chained handler is actually an interrupt flow, and not a normal handler.
IRQF_SHAREDacts at the wrong level for that.I can see two possibilities:
Quoted 7 lines
- the l2-intc gets turned into a normal handler, and does the demux from there. Horrible stuff.
- the i2c controller gets parented to the l2c-int as a fake interrupt, and gets called from there. Horrible stuff.
Pick your poison... :-/
Thanks for the info.
Option 3 - remove l2-intc and drop back to polling the i2c-brcmstb blocks (which the driver supports anyway).
HDMI I2C generally isn't heavily used once displays are connected, so I'd be OK with that.
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
(We can keep the l2-intc that handles CEC and HPD as that is on a unique GIC interrupt).
Agreed, Maxime or Nicolas do you want me to send a revert of this patch?
Reverting seems the safe move, but I'll defer to whatever Maxime says.
Yes, reverting it seems like the easiest way forward. If you can send it Florian that would be great :)
Maxime
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH v2 15/15 ARM: dts: bcm2711: Add the CEC interrupt controller
In reply to Maxime RipardThe CEC and hotplug interrupts go through an interrupt controller shared between the two HDMI controllers.
Let's add that interrupt controller and the interrupts for both HDMI controllers
--- arch/arm/boot/dts/bcm2711.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
arch/arm/boot/dts/bcm2711.dtsi +18 -0
@@ -316,6 +316,14 @@ bsc_intr: interrupt-controller@7ef00040 { #interrupt-cells = <1>; }; + aon_intr: interrupt-controller@7ef00100 { + compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; + reg = <0x7ef00100 0x30>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + }; + hdmi0: hdmi@7ef00700 { compatible = "brcm,bcm2711-hdmi0"; reg = <0x7ef00700 0x300>,
@@ -338,6 +346,11 @@ hdmi0: hdmi@7ef00700 { "hd"; clock-names = "hdmi", "bvb", "audio", "cec"; resets = <&dvp 0>; + interrupt-parent = <&aon_intr>; + interrupts = <0>, <1>, <2>, + <3>, <4>, <5>; + interrupt-names = "cec-tx", "cec-rx", "cec-low", + "wakeup", "hpd-connected", "hpd-removed"; ddc = <&ddc0>; dmas = <&dma 10>; dma-names = "audio-rx";
@@ -377,6 +390,11 @@ hdmi1: hdmi@7ef05700 { ddc = <&ddc1>; clock-names = "hdmi", "bvb", "audio", "cec"; resets = <&dvp 1>; + interrupt-parent = <&aon_intr>; + interrupts = <8>, <7>, <6>, + <9>, <10>, <11>; + interrupt-names = "cec-tx", "cec-rx", "cec-low", + "wakeup", "hpd-connected", "hpd-removed"; dmas = <&dma 17>; dma-names = "audio-rx"; status = "disabled";
Signature · 1 line
2.29.2
Re: [PATCH v2 15/15] ARM: dts: bcm2711: Add the CEC interrupt controller
Quoted 9 lines · Maxime Ripard
The CEC and hotplug interrupts go through an interrupt controller shared between the two HDMI controllers.
Let's add that interrupt controller and the interrupts for both HDMI controllers
Reviewed-by Florian Fainelli <[email protected]>Signed-off-by Maxime Ripard <[email protected]>---
Applied for-next.
Thanks,
Nicolas
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi Maxime,
Quoted 9 lines · Maxime Ripard
Hi,
Here's a series introducing the CEC support for the BCM2711 found on the RaspberryPi4.
The BCM2711 HDMI controller uses a similar layout for the CEC registers, the main difference being that the interrupt handling part is now shared between both HDMI controllers.
Quoted 6 lines
This series is mainly about fixing a couple of bugs, reworking the driver to support having two different interrupts, one for each direction, provided by an external irqchip, and enables the irqchip driver for the controller we have.
This has been tested on an RPi3 and RPi4, but requires the latest firmware. It's is based on the 10 and 12 bpc series.
Thank you for this series, I plan to test this later this week.
Regards,
Hans
Quoted 341 lines
Here is the cec-compliance output:
pi@raspberrypi:~$ cec-ctl --tuner -p 1.0.0.0 The CEC adapter doesn't allow setting the physical address manually, ignore this option.Driver Info:
Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010eLogical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask :0x0008
CEC Version : 2.0
Vendor ID :0x000c03(HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
Nonepi@raspberrypi:~$ cec-compliance cec-compliance SHA : not available Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : 1.0.0.0 Logical Address Mask : 0x0008 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Tuner Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1) Primary Device Type : Tuner Logical Address Type : Tuner All Device Types : Tuner RC TV Profile : None Device Features :None
Compliance test for device
/dev/cec0:The test results mean the following:
OK Supported correctly by the device.
OK (Not Supported) Not supported and not mandatory for the device.
OK (Presumed) Presumably supported. Manually check to confirm.
OK (Unexpected) Supported correctly but is not expected to be supported for this device.
OK (Refused) Supported by the device, but was refused.
FAIL Failed and was expected to be supported by this device.Find remote devices:
Polling: OKNetwork topology:
System Information for device 0 (TV) from device 3 (Tuner 1):
CEC Version : 2.0
Physical Address : 0.0.0.0
Primary Device Type : TV
Vendor ID :0x000c03
OSD Name : 'TV '
Power Status : Tx, OK, Rx, OK, Feature AbortTotal: 1, Succeeded: 1, Failed: 0, Warnings: 0
pi@raspberrypi:~$ cec-ctl -d1 --tuner -p 1.0.0.0 The CEC adapter doesn't allow setting the physical address manually, ignore this option.Driver Info:
Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010eLogical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask :0x0008
CEC Version : 2.0
Vendor ID :0x000c03(HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
Nonepi@raspberrypi:~$ cec-compliance -d1 cec-compliance SHA : not available Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : 1.0.0.0 Logical Address Mask : 0x0008 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Tuner Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1) Primary Device Type : Tuner Logical Address Type : Tuner All Device Types : Tuner RC TV Profile : None Device Features :None
Compliance test for device
/dev/cec1:The test results mean the following:
OK Supported correctly by the device.
OK (Not Supported) Not supported and not mandatory for the device.
OK (Presumed) Presumably supported. Manually check to confirm.
OK (Unexpected) Supported correctly but is not expected to be supported for this device.
OK (Refused) Supported by the device, but was refused.
FAIL Failed and was expected to be supported by this device.Find remote devices:
Polling: OKNetwork topology:
System Information for device 0 (TV) from device 3 (Tuner 1):
CEC Version : 2.0
Physical Address : 0.0.0.0
Primary Device Type : TV
Vendor ID :0x000c03
OSD Name : 'TV '
Power Status : Tx, OK, Rx, OK, Feature AbortTotal: 1, Succeeded: 1, Failed: 0, Warnings: 0
And for the hotplug detect test:
pi@raspberrypi:~$ cec-ctl --playback Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
pi@raspberrypi:~$ cec-ctl -t0 --image-view-on Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
Transmit from Unregistered to TV (15 to 0):
CEC_MSG_IMAGE_VIEW_ON(0x04)Sequence: 1 Tx Timestamp: 9182.611s pi@raspberrypi:~$ cec-ctl -d1 --playback Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
pi@raspberrypi:~$ cec-ctl -d1 -t0 --image-view-on Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
Transmit from Unregistered to TV (15 to 0):
CEC_MSG_IMAGE_VIEW_ON(0x04)Sequence: 1 Tx Timestamp: 9207.191sWith the pulse-eight side reporting:
$ sudo cec-ctl -M Driver Info: Driver Name : pulse8-cec Adapter Name : serio0 Capabilities : 0x0000003f Physical Address Logical Addresses Transmit Passthrough Remote Control Support Monitor All Driver version : 5.9.16 Available Logical Addresses: 1 Connector Info : None Physical Address : 0.0.0.0 Logical Address Mask : 0x0001 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : 'TV ' Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 0 (TV) Primary Device Type : TV Logical Address Type : TV All Device Types : TV RC TV Profile : None Device Features :None
Initial Event: State Change: PA: 0.0.0.0, LA mask:
0x0001, Conn Info: noReceived from Unregistered to TV (15 to 0):
IMAGE_VIEW_ON(0x04) Received from Unregistered to TV (15 to 0):IMAGE_VIEW_ON(0x04)Let me know what you think,
MaximeChanges from v1:
- Removed the irqchip patch in favor of a select in mach-bcm
- Fixed HDMI1 interrupt numbers
- Removed redundant call todrm_connector_update_edid_property
- Fixed the condition invc4_hdmi_connector_detect
- Added the tags
- Rebased on top of drm-misc-next-2021-01-06Dom Cobley (5):
drm/vc4: hdmi: Move hdmi reset to bind
drm/vc4: hdmi: Fix register offset with longer CEC messages drm/vc4: hdmi: Fix up CEC registers
drm/vc4: hdmi: Restore cec physical address on reconnect drm/vc4: hdmi: Removecec_availableflagMaxime Ripard (10):
ARM: bcm: SelectBRCMSTB_L2_IRQfor bcm2835
drm/vc4: hdmi: Compute the CEC clock divider from the clock rate drm/vc4: hdmi: Update the CEC clock divider on HSM rate change drm/vc4: hdmi: Introduce a CEC clock
drm/vc4: hdmi: Split the interrupt handlers
drm/vc4: hdmi: Support BCM2711 CEC interrupt setup drm/vc4: hdmi: Don't register the CEC adapter if there's no interrupts
dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
ARM: dts: bcm2711: Add the BSC interrupt controller
ARM: dts: bcm2711: Add the CEC interrupt controller.../bindings/display/brcm,bcm2711-hdmi.yaml | 20 +- arch/arm/boot/dts/bcm2711.dtsi | 30 +++ arch/arm/mach-bcm/Kconfig | 1 + arch/arm64/Kconfig.platforms | 1 + drivers/gpu/drm/vc4/vc4_hdmi.c | 223 ++++++++++++++---- drivers/gpu/drm/vc4/vc4_hdmi.h | 11 +- drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 4 +- 7 files changed, 234 insertions(+), 56 deletions(-)
Quoted 12 lines · Hans Verkuil
Hi Maxime,
Quoted 9 lines · Maxime Ripard
Hi,
Here's a series introducing the CEC support for the BCM2711 found on the RaspberryPi4.
The BCM2711 HDMI controller uses a similar layout for the CEC registers, the main difference being that the interrupt handling part is now shared between both HDMI controllers.
Quoted 8 lines
Quoted 6 lines
This series is mainly about fixing a couple of bugs, reworking the driver to support having two different interrupts, one for each direction, provided by an external irqchip, and enables the irqchip driver for the controller we have.
This has been tested on an RPi3 and RPi4, but requires the latest firmware. It's is based on the 10 and 12 bpc series.
Thank you for this series, I plan to test this later this week.
Testing is delayed: my microHDMI to HDMI adapter has problems with the CEC pin (possibly not connected at all). I've ordered adapter cables (hopefully of better quality), but those haven't arrived yet. I expect them later this week.
Regards,
Hans
Quoted 347 lines
Regards,
Hans
Quoted 341 lines
Here is the cec-compliance output:
pi@raspberrypi:~$ cec-ctl --tuner -p 1.0.0.0 The CEC adapter doesn't allow setting the physical address manually, ignore this option.Driver Info:
Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010eLogical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask :0x0008
CEC Version : 2.0
Vendor ID :0x000c03(HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
Nonepi@raspberrypi:~$ cec-compliance cec-compliance SHA : not available Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : 1.0.0.0 Logical Address Mask : 0x0008 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Tuner Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1) Primary Device Type : Tuner Logical Address Type : Tuner All Device Types : Tuner RC TV Profile : None Device Features :None
Compliance test for device
/dev/cec0:The test results mean the following:
OK Supported correctly by the device.
OK (Not Supported) Not supported and not mandatory for the device.
OK (Presumed) Presumably supported. Manually check to confirm.
OK (Unexpected) Supported correctly but is not expected to be supported for this device.
OK (Refused) Supported by the device, but was refused.
FAIL Failed and was expected to be supported by this device.Find remote devices:
Polling: OKNetwork topology:
System Information for device 0 (TV) from device 3 (Tuner 1):
CEC Version : 2.0
Physical Address : 0.0.0.0
Primary Device Type : TV
Vendor ID :0x000c03
OSD Name : 'TV '
Power Status : Tx, OK, Rx, OK, Feature AbortTotal: 1, Succeeded: 1, Failed: 0, Warnings: 0
pi@raspberrypi:~$ cec-ctl -d1 --tuner -p 1.0.0.0 The CEC adapter doesn't allow setting the physical address manually, ignore this option.Driver Info:
Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010eLogical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask :0x0008
CEC Version : 2.0
Vendor ID :0x000c03(HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
Nonepi@raspberrypi:~$ cec-compliance -d1 cec-compliance SHA : not available Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : 1.0.0.0 Logical Address Mask : 0x0008 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Tuner Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1) Primary Device Type : Tuner Logical Address Type : Tuner All Device Types : Tuner RC TV Profile : None Device Features :None
Compliance test for device
/dev/cec1:The test results mean the following:
OK Supported correctly by the device.
OK (Not Supported) Not supported and not mandatory for the device.
OK (Presumed) Presumably supported. Manually check to confirm.
OK (Unexpected) Supported correctly but is not expected to be supported for this device.
OK (Refused) Supported by the device, but was refused.
FAIL Failed and was expected to be supported by this device.Find remote devices:
Polling: OKNetwork topology:
System Information for device 0 (TV) from device 3 (Tuner 1):
CEC Version : 2.0
Physical Address : 0.0.0.0
Primary Device Type : TV
Vendor ID :0x000c03
OSD Name : 'TV '
Power Status : Tx, OK, Rx, OK, Feature AbortTotal: 1, Succeeded: 1, Failed: 0, Warnings: 0
And for the hotplug detect test:
pi@raspberrypi:~$ cec-ctl --playback Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
pi@raspberrypi:~$ cec-ctl -t0 --image-view-on Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
Transmit from Unregistered to TV (15 to 0):
CEC_MSG_IMAGE_VIEW_ON(0x04)Sequence: 1 Tx Timestamp: 9182.611s pi@raspberrypi:~$ cec-ctl -d1 --playback Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
pi@raspberrypi:~$ cec-ctl -d1 -t0 --image-view-on Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
Transmit from Unregistered to TV (15 to 0):
CEC_MSG_IMAGE_VIEW_ON(0x04)Sequence: 1 Tx Timestamp: 9207.191sWith the pulse-eight side reporting:
$ sudo cec-ctl -M Driver Info: Driver Name : pulse8-cec Adapter Name : serio0 Capabilities : 0x0000003f Physical Address Logical Addresses Transmit Passthrough Remote Control Support Monitor All Driver version : 5.9.16 Available Logical Addresses: 1 Connector Info : None Physical Address : 0.0.0.0 Logical Address Mask : 0x0001 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : 'TV ' Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 0 (TV) Primary Device Type : TV Logical Address Type : TV All Device Types : TV RC TV Profile : None Device Features :None
Initial Event: State Change: PA: 0.0.0.0, LA mask:
0x0001, Conn Info: noReceived from Unregistered to TV (15 to 0):
IMAGE_VIEW_ON(0x04) Received from Unregistered to TV (15 to 0):IMAGE_VIEW_ON(0x04)Let me know what you think,
MaximeChanges from v1:
- Removed the irqchip patch in favor of a select in mach-bcm
- Fixed HDMI1 interrupt numbers
- Removed redundant call todrm_connector_update_edid_property
- Fixed the condition invc4_hdmi_connector_detect
- Added the tags
- Rebased on top of drm-misc-next-2021-01-06Dom Cobley (5):
drm/vc4: hdmi: Move hdmi reset to bind
drm/vc4: hdmi: Fix register offset with longer CEC messages drm/vc4: hdmi: Fix up CEC registers
drm/vc4: hdmi: Restore cec physical address on reconnect drm/vc4: hdmi: Removecec_availableflagMaxime Ripard (10):
ARM: bcm: SelectBRCMSTB_L2_IRQfor bcm2835
drm/vc4: hdmi: Compute the CEC clock divider from the clock rate drm/vc4: hdmi: Update the CEC clock divider on HSM rate change drm/vc4: hdmi: Introduce a CEC clock
drm/vc4: hdmi: Split the interrupt handlers
drm/vc4: hdmi: Support BCM2711 CEC interrupt setup drm/vc4: hdmi: Don't register the CEC adapter if there's no interrupts
dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
ARM: dts: bcm2711: Add the BSC interrupt controller
ARM: dts: bcm2711: Add the CEC interrupt controller.../bindings/display/brcm,bcm2711-hdmi.yaml | 20 +- arch/arm/boot/dts/bcm2711.dtsi | 30 +++ arch/arm/mach-bcm/Kconfig | 1 + arch/arm64/Kconfig.platforms | 1 + drivers/gpu/drm/vc4/vc4_hdmi.c | 223 ++++++++++++++---- drivers/gpu/drm/vc4/vc4_hdmi.h | 11 +- drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 4 +- 7 files changed, 234 insertions(+), 56 deletions(-)
Quoted 17 lines · Hans Verkuil
Quoted 16 lines · Hans Verkuil
Hi Maxime,
Quoted 13 lines · Maxime Ripard
Hi,
Here's a series introducing the CEC support for the BCM2711 found on the RaspberryPi4.
The BCM2711 HDMI controller uses a similar layout for the CEC registers, the main difference being that the interrupt handling part is now shared between both HDMI controllers.
This series is mainly about fixing a couple of bugs, reworking the driver to support having two different interrupts, one for each direction, provided by an external irqchip, and enables the irqchip driver for the controller we have.
Quoted 8 lines
Quoted 4 lines
Quoted 2 lines
This has been tested on an RPi3 and RPi4, but requires the latest firmware. It's is based on the 10 and 12 bpc series.
Thank you for this series, I plan to test this later this week.
Testing is delayed: my microHDMI to HDMI adapter has problems with the CEC pin (possibly not connected at all). I've ordered adapter cables (hopefully of better quality), but those haven't arrived yet. I expect them later this week.
After testing this you can add my:
for the patches in this series.
Thank you for working on this!
Regards,
Hans
Quoted 353 lines
Regards,
Hans
Quoted 347 lines
Regards,
Hans
Quoted 341 lines
Here is the cec-compliance output:
pi@raspberrypi:~$ cec-ctl --tuner -p 1.0.0.0 The CEC adapter doesn't allow setting the physical address manually, ignore this option.Driver Info:
Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010eLogical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask :0x0008
CEC Version : 2.0
Vendor ID :0x000c03(HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
Nonepi@raspberrypi:~$ cec-compliance cec-compliance SHA : not available Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : 1.0.0.0 Logical Address Mask : 0x0008 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Tuner Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1) Primary Device Type : Tuner Logical Address Type : Tuner All Device Types : Tuner RC TV Profile : None Device Features :None
Compliance test for device
/dev/cec0:The test results mean the following:
OK Supported correctly by the device.
OK (Not Supported) Not supported and not mandatory for the device.
OK (Presumed) Presumably supported. Manually check to confirm.
OK (Unexpected) Supported correctly but is not expected to be supported for this device.
OK (Refused) Supported by the device, but was refused.
FAIL Failed and was expected to be supported by this device.Find remote devices:
Polling: OKNetwork topology:
System Information for device 0 (TV) from device 3 (Tuner 1):
CEC Version : 2.0
Physical Address : 0.0.0.0
Primary Device Type : TV
Vendor ID :0x000c03
OSD Name : 'TV '
Power Status : Tx, OK, Rx, OK, Feature AbortTotal: 1, Succeeded: 1, Failed: 0, Warnings: 0
pi@raspberrypi:~$ cec-ctl -d1 --tuner -p 1.0.0.0 The CEC adapter doesn't allow setting the physical address manually, ignore this option.Driver Info:
Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010eLogical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask :0x0008
CEC Version : 2.0
Vendor ID :0x000c03(HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
Nonepi@raspberrypi:~$ cec-compliance -d1 cec-compliance SHA : not available Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : 1.0.0.0 Logical Address Mask : 0x0008 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Tuner Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 3 (Tuner 1) Primary Device Type : Tuner Logical Address Type : Tuner All Device Types : Tuner RC TV Profile : None Device Features :None
Compliance test for device
/dev/cec1:The test results mean the following:
OK Supported correctly by the device.
OK (Not Supported) Not supported and not mandatory for the device.
OK (Presumed) Presumably supported. Manually check to confirm.
OK (Unexpected) Supported correctly but is not expected to be supported for this device.
OK (Refused) Supported by the device, but was refused.
FAIL Failed and was expected to be supported by this device.Find remote devices:
Polling: OKNetwork topology:
System Information for device 0 (TV) from device 3 (Tuner 1):
CEC Version : 2.0
Physical Address : 0.0.0.0
Primary Device Type : TV
Vendor ID :0x000c03
OSD Name : 'TV '
Power Status : Tx, OK, Rx, OK, Feature AbortTotal: 1, Succeeded: 1, Failed: 0, Warnings: 0
And for the hotplug detect test:
pi@raspberrypi:~$ cec-ctl --playback Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
pi@raspberrypi:~$ cec-ctl -t0 --image-view-on Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
Transmit from Unregistered to TV (15 to 0):
CEC_MSG_IMAGE_VIEW_ON(0x04)Sequence: 1 Tx Timestamp: 9182.611s pi@raspberrypi:~$ cec-ctl -d1 --playback Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
pi@raspberrypi:~$ cec-ctl -d1 -t0 --image-view-on Driver Info: Driver Name : vc4_hdmi Adapter Name : vc4 Capabilities : 0x0000010e Logical Addresses Transmit Passthrough Driver version : 5.10.0 Available Logical Addresses: 1 Physical Address : f.f.f.f Logical Address Mask : 0x0000 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : Playback Logical Addresses : 1 (Allow RC Passthrough)Logical Address : Not Allocated Primary Device Type : Playback Logical Address Type : Playback All Device Types : Playback RC TV Profile : None Device Features :None
Transmit from Unregistered to TV (15 to 0):
CEC_MSG_IMAGE_VIEW_ON(0x04)Sequence: 1 Tx Timestamp: 9207.191sWith the pulse-eight side reporting:
$ sudo cec-ctl -M Driver Info: Driver Name : pulse8-cec Adapter Name : serio0 Capabilities : 0x0000003f Physical Address Logical Addresses Transmit Passthrough Remote Control Support Monitor All Driver version : 5.9.16 Available Logical Addresses: 1 Connector Info : None Physical Address : 0.0.0.0 Logical Address Mask : 0x0001 CEC Version : 2.0 Vendor ID : 0x000c03 (HDMI) OSD Name : 'TV ' Logical Addresses : 1 (Allow RC Passthrough)Logical Address : 0 (TV) Primary Device Type : TV Logical Address Type : TV All Device Types : TV RC TV Profile : None Device Features :None
Initial Event: State Change: PA: 0.0.0.0, LA mask:
0x0001, Conn Info: noReceived from Unregistered to TV (15 to 0):
IMAGE_VIEW_ON(0x04) Received from Unregistered to TV (15 to 0):IMAGE_VIEW_ON(0x04)Let me know what you think,
MaximeChanges from v1:
- Removed the irqchip patch in favor of a select in mach-bcm
- Fixed HDMI1 interrupt numbers
- Removed redundant call todrm_connector_update_edid_property
- Fixed the condition invc4_hdmi_connector_detect
- Added the tags
- Rebased on top of drm-misc-next-2021-01-06Dom Cobley (5):
drm/vc4: hdmi: Move hdmi reset to bind
drm/vc4: hdmi: Fix register offset with longer CEC messages drm/vc4: hdmi: Fix up CEC registers
drm/vc4: hdmi: Restore cec physical address on reconnect drm/vc4: hdmi: Removecec_availableflagMaxime Ripard (10):
ARM: bcm: SelectBRCMSTB_L2_IRQfor bcm2835
drm/vc4: hdmi: Compute the CEC clock divider from the clock rate drm/vc4: hdmi: Update the CEC clock divider on HSM rate change drm/vc4: hdmi: Introduce a CEC clock
drm/vc4: hdmi: Split the interrupt handlers
drm/vc4: hdmi: Support BCM2711 CEC interrupt setup drm/vc4: hdmi: Don't register the CEC adapter if there's no interrupts
dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
ARM: dts: bcm2711: Add the BSC interrupt controller
ARM: dts: bcm2711: Add the CEC interrupt controller.../bindings/display/brcm,bcm2711-hdmi.yaml | 20 +- arch/arm/boot/dts/bcm2711.dtsi | 30 +++ arch/arm/mach-bcm/Kconfig | 1 + arch/arm64/Kconfig.platforms | 1 + drivers/gpu/drm/vc4/vc4_hdmi.c | 223 ++++++++++++++---- drivers/gpu/drm/vc4/vc4_hdmi.h | 11 +- drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 4 +- 7 files changed, 234 insertions(+), 56 deletions(-)
Hi,
Quoted 9 lines · Maxime Ripard
Hi,
Here's a series introducing the CEC support for the BCM2711 found on the RaspberryPi4.
The BCM2711 HDMI controller uses a similar layout for the CEC registers, the main difference being that the interrupt handling part is now shared between both HDMI controllers.
Quoted 6 lines
This series is mainly about fixing a couple of bugs, reworking the driver to support having two different interrupts, one for each direction, provided by an external irqchip, and enables the irqchip driver for the controller we have.
This has been tested on an RPi3 and RPi4, but requires the latest firmware. It's is based on the 10 and 12 bpc series.
I applied patches #1 and #14 for-next. I'm waiting on Hans' testing for #15.
Regards,
Nicolas
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Maxime Ripard
AppliedHi!
Quoted 12 lines · Nicolas Saenz Julienne
Hi,
Quoted 9 lines · Maxime Ripard
Hi,
Here's a series introducing the CEC support for the BCM2711 found on the RaspberryPi4.
The BCM2711 HDMI controller uses a similar layout for the CEC registers, the main difference being that the interrupt handling part is now shared between both HDMI controllers.
Quoted 8 lines
Quoted 6 lines
This series is mainly about fixing a couple of bugs, reworking the driver to support having two different interrupts, one for each direction, provided by an external irqchip, and enables the irqchip driver for the controller we have.
This has been tested on an RPi3 and RPi4, but requires the latest firmware. It's is based on the 10 and 12 bpc series.
I applied patches #1 and #14 for-next. I'm waiting on Hans' testing for #15.
I've applied to drm-misc-next the patches 2 to 13
Maxime
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel