Skip to contentSkip to conversation

iwd in AP mode: no HT capabilities

DISCUSSION [email protected] 2 participants 2 messages Jan 14, 2021

lore
Share & tools
lore
#0 lore raw

Hi,

I tried to switch from wpa_supplicant to iwd to start an access point.

When looking at the scan results from another machine, I see that when using iwd, the device sends no HT capabilities and only supports 11MBit/s.

output from "iw dev wlp2s0 scan":

with iwd based ap:
-----
BSS 74:da:38:f4:e1:42(on wlp2s0)
last seen: 789976.536s [boottime]
TSF: 11382336 usec (0d, 00:00:11)
freq: 2437
beacon interval: 100 TUs
capability: ESS Privacy (0x0011)
signal: -48.00 dBm
last seen: 4088 ms ago
Information elements from Probe Response frame:
SSID: testbox
Supported rates: 1.0* 5.5 11.0
DS Parameter set: channel 6
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* Response Type: 3 (AP)
* UUID: 927467be-c802-5217-a136-a5489eb14b24
* Manufacturer:
* Model:
* Model Number:
* Serial Number:
* Primary Device Type: 1-00372a04-1
* Device name: testbox
* Config methods: PBC
* Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
-----

with wpa_supplicant based ap:
-----
BSS d0:37:45:99:3e:1f(on wlp2s0)
last seen: 789193.105s [boottime]
TSF: 5592759 usec (0d, 00:00:05)
freq: 2412
beacon interval: 100 TUs
capability: ESS Privacy ShortSlotTime (0x0411)
signal: -58.00 dBm
last seen: 3230 ms ago
Information elements from Probe Response frame:
SSID: testbox
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0 DS Parameter set: channel 1
ERP: Barker_Preamble_Mode
Extended supported rates: 24.0 36.0 48.0 54.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK PSK/SHA-256
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
HT capabilities:
Capabilities: 0x92c
HT20
SM Power Save disabled
RX HT20 SGI
RX STBC 1-stream
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 16 usec (0x07) HT Max RX data rate: 476 Mbps
HT TX/RX MCS rate indexes supported: 0-7
HT operation:
* primary channel: 1
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: no
* non-GF present: 0
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
WMM: * Parameter version 1
* u-APSD
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 2976 usec
* VO: CW 3-7, AIFSN 2, TXOP 1472 usec
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
* Device name:
* Primary Device Type: 0-00000000-0
-----

Is this a driver issue or a general problem with iwd?

Best regards,
Georg

#1 lore raw

Hi Georg,

Quoted 3 lines · On Thu, 14 Jan 2021 at 19:54, <[email protected]> wrote:

I tried to switch from wpa_supplicant to iwd to start an access point.

When looking at the scan results from another machine, I see that when using iwd, the device sends no HT capabilities and only supports 11MBit/s.

This is a missing feature in IWD at this time, the AP mode is still very basic and only reports a few hardcoded bitrates. AP beacon changes are blocked by an ongoing development in ell for the moment.

Best regards