Skip to contentSkip to conversation

arm64: dts: rockchip: cleanup cpu_thermal node of rk3399-rock960.dts

PATCH Applied Johan Jonker 2 participants 2 messages Jan 18, 2021 – Jan 25, 2021

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 arm64: dts: rockchip: cleanup cpu_thermal node of rk3399-rock960.dts

The cpu_thermal node in the rk3399-rock960.dts file does not reference &cpu_thermal directly to add the board-specific parts, but also repeats all the SoC default properties.
Clean the whole thing up and fix alignment.
Place new nodes in the correct alphabetical order. Compered to rk3399.dtsi the temperature property in cpu_alert0 changes from <70000> to <65000>.
A sustainable-power property was added.
The trip property in cooling map0 points to <&cpu_alert1> instead of <&cpu_alert0>.

---
 arch/arm64/boot/dts/rockchip/rk3399-rock960.dts | 53 +++++++------------------
 1 file changed, 14 insertions(+), 39 deletions(-)
arch/arm64/boot/dts/rockchip/rk3399-rock960.dts +14 -39
index b20774081..1a23e8f3c 100644
@@ -63,6 +63,20 @@
 
 };
 
+&cpu_alert0 {
+	temperature = <65000>;
+};
+
+&cpu_thermal {
+	sustainable-power = <1550>;
+
+	cooling-maps {
+		map0 {
+			trip = <&cpu_alert1>;
+		};
+	};
+};
+
 &pcie0 {
 	ep-gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_HIGH>;
 };
@@ -125,45 +139,6 @@
 	status = "okay";
 };
 
-&thermal_zones {
-	cpu_thermal: cpu-thermal {
-		polling-delay-passive = <100>;
-		polling-delay = <1000>;
-		thermal-sensors = <&tsadc 0>;
-		sustainable-power = <1550>;
-
-		trips {
-			cpu_alert0: cpu_alert0 {
-				    temperature = <65000>;
-				    hysteresis = <2000>;
-				    type = "passive";
-			};
-
-			cpu_alert1: cpu_alert1 {
-				    temperature = <75000>;
-				    hysteresis = <2000>;
-				    type = "passive";
-			};
-
-			cpu_crit: cpu_crit {
-				  temperature = <95000>;
-				  hysteresis = <2000>;
-				  type = "critical";
-			};
-		};
-
-		cooling-maps {
-			     map0 {
-
-			     trip = <&cpu_alert1>;
-			     cooling-device =
-					<&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					<&cpu_b1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-			};
-		};
-	};
-};
-
 &usbdrd_dwc3_0 {
 	dr_mode = "otg";
 };
Signature · 7 lines
2.11.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
maintainer Applied
#1 lore raw
Quoted 10 lines · Johan Jonker

The cpu_thermal node in the rk3399-rock960.dts file does not reference &cpu_thermal directly to add the board-specific parts, but also repeats all the SoC default properties.
Clean the whole thing up and fix alignment.
Place new nodes in the correct alphabetical order. Compered to rk3399.dtsi the temperature property in cpu_alert0 changes from <70000> to <65000>.
A sustainable-power property was added.
The trip property in cooling map0 points to <&cpu_alert1> instead of <&cpu_alert0>.

Applied, thanks!

[1/1] arm64: dts: rockchip: cleanup cpu_thermal node of rk3399-rock960.dts

      commit: 376e46b5dd0ad9d06f029bbc4a66dd25dd059597

Best regards,

Signature · 6 lines
Heiko Stuebner <[email protected]>

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip