Skip to contentSkip to conversation

arm64: dts: fsl-ls1012a-rdb: add i2c devices

PATCH Applied Pawel Dembicki 2 participants 3 messages Jan 19, 2021 – Jan 29, 2021

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 arm64: dts: fsl-ls1012a-rdb: add i2c devices

LS1012A-RDB equipped in some i2c devices:
- 3x GPIO Expander: PCAL9555A (NXP)
- Gyro: FXAS21002 (NXP)
- Accelerometer: FXOS8700 (NXP)
- Current & Power Monitor: INA220 (TI)

This patch add listed devices to dts.

---
Changes in v2:
- resend only

 .../boot/dts/freescale/fsl-ls1012a-rdb.dts    | 45 +++++++++++++++++++
 1 file changed, 45 insertions(+)
arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts +45 -0
index d45c17620b98..12117a973eb6 100644
@@ -7,6 +7,7 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "fsl-ls1012a.dtsi"
 
 / {
@@ -33,6 +34,50 @@ &esdhc1 {
 
 &i2c0 {
 	status = "okay";
+
+	accelerometer@1e {
+		compatible = "nxp,fxos8700";
+		reg = <0x1e>;
+		interrupt-parent = <&gpio26>;
+		interrupts = <13 IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "INT1";
+	};
+
+	gyroscope@20 {
+		compatible = "nxp,fxas21002c";
+		reg = <0x20>;
+	};
+
+	gpio@24 {
+		compatible = "nxp,pcal9555a";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@25 {
+		compatible = "nxp,pcal9555a";
+		reg = <0x25>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio26: gpio@26 {
+		compatible = "nxp,pcal9555a";
+		reg = <0x26>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	current-sensor@40 {
+		compatible = "ti,ina220";
+		reg = <0x40>;
+		shunt-resistor = <2000>;
+	};
 };
 
 &qspi {
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#1 lore raw

PATCH v2 2/2 arm64: dts: fsl-ls1012a-frdm: add spi-uart device

This patch adds spi-uart controller to LS1012A-FRDM board dts. Device is equipped in SC16IS740 from NXP.

---
Changes in v2:
- reordered property list
- change clock name to "clock-sc16is7xx"

 .../boot/dts/freescale/fsl-ls1012a-frdm.dts   | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts +21 -0
index 67702667ed8a..2517528f684f 100644
@@ -7,6 +7,7 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "fsl-ls1012a.dtsi"
 
 / {
@@ -57,6 +58,26 @@ simple-audio-card,codec {
 	};
 };
 
+&dspi {
+	bus-num = <0>;
+	status = "okay";
+
+	serial@0 {
+		compatible = "nxp,sc16is740";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		clocks = <&sc16is7xx_clk>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+
+		sc16is7xx_clk: clock-sc16is7xx {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+		};
+	};
+};
+
 &duart0 {
 	status = "okay";
 };
Signature · 1 line
2.25.1
Applied
#2 lore raw
In reply to Pawel Dembicki
Quoted 9 lines · Pawel Dembicki

LS1012A-RDB equipped in some i2c devices:
- 3x GPIO Expander: PCAL9555A (NXP)
- Gyro: FXAS21002 (NXP)
- Accelerometer: FXOS8700 (NXP)
- Current & Power Monitor: INA220 (TI)

This patch add listed devices to dts.

Applied both, thanks.

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel