hwmon: Add AHT10 Temperature and Humidity Sensor Driver
Subsystems (2)
PATCH v3 1/1 hwmon: Add AHT10 Temperature and Humidity Sensor Driver
This patch adds a hwmon driver for the AHT10 Temperature and Humidity sensor. It has a maximum sample rate, as the datasheet states that the chip may heat up if it is sampled more than once every two seconds.
Has been tested a to work on a raspberrypi0w
Changes from v2:
Add reference to documentation to index.rst
Properly align defines
Clamp value instead of returning error
Adjust return values
Remove unnecessary print, check and comment
Major changes from initial patch:
Removed devicetree/of references
Removed aht10_reset, aht10_remove
Add documentation
Switch to hwmon channels, attributes and info More appropriate usage of mutex
Return standard error codes
Add checking statements for errors that are returned Other code improvements as suggested
--- Documentation/hwmon/aht10.rst | 46 +++++ Documentation/hwmon/index.rst | 1 + drivers/hwmon/Kconfig | 10 + drivers/hwmon/Makefile | 1 + drivers/hwmon/aht10.c | 347 ++++++++++++++++++++++++++++++++++ 5 files changed, 405 insertions(+) create mode 100644 Documentation/hwmon/aht10.rst create mode 100644 drivers/hwmon/aht10.c
Documentation/hwmon/aht10.rst new file +46 -0
@@ -0,0 +1,46 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver aht10 +===================== + +Supported chips: + + * Aosong AHT10 + + Prefix: 'aht10' + + Addresses scanned: None + + Datasheet: + + Chinese: http://www.aosong.com/userfiles/files/media/AHT10%E4%BA%A7%E5%93%81%E6%89%8B%E5%86%8C%20A3%2020201210.pdf + English: https://server4.eca.ir/eshop/AHT10/Aosong_AHT10_en_draft_0c.pdf + +Author: Johannes Cornelis Draaijer <[email protected]> + + +Description +----------- + +The AHT10 is a Temperature and Humidity sensor + +The address of this i2c device may only be 0x38 + +Usage Notes +----------- + +This driver does not probe for AHT10 devices, as there is no reliable +way to determine if an i2c chip is or isn't an AHT10. The device has +to be instantiated explicitly with the address 0x38. See +Documentation/i2c/instantiating-devices.rst for details. + +Sysfs entries +------------- + +=============== ============================================ +temp1_input Measured temperature in millidegrees Celcius +humidity1_input Measured humidity in %H +update_interval The minimum interval for polling the sensor, + in milliseconds. Writable. Must be at + least 2000. +=============== ============================================
Documentation/hwmon/index.rst +1 -0
@@ -38,6 +38,7 @@ Hardware Monitoring Kernel Drivers adt7462 adt7470 adt7475 + aht10 amc6821 amd_energy asb100
drivers/hwmon/Kconfig +10 -0
@@ -257,6 +257,16 @@ config SENSORS_ADT7475 This driver can also be built as a module. If so, the module will be called adt7475. +config SENSORS_AHT10 + tristate "Aosong AHT10" + depends on I2C + help + If you say yes here, you get support for the Aosong AHT10 + temperature and humidity sensors + + This driver can also be built as a module. If so, the module + will be called aht10. + config SENSORS_AS370 tristate "Synaptics AS370 SoC hardware monitoring driver" help
drivers/hwmon/Makefile +1 -0
@@ -45,6 +45,7 @@ obj-$(CONFIG_SENSORS_ADT7411) += adt7411.o obj-$(CONFIG_SENSORS_ADT7462) += adt7462.o obj-$(CONFIG_SENSORS_ADT7470) += adt7470.o obj-$(CONFIG_SENSORS_ADT7475) += adt7475.o +obj-$(CONFIG_SENSORS_AHT10) += aht10.o obj-$(CONFIG_SENSORS_AMD_ENERGY) += amd_energy.o obj-$(CONFIG_SENSORS_APPLESMC) += applesmc.o obj-$(CONFIG_SENSORS_ARM_SCMI) += scmi-hwmon.o
drivers/hwmon/aht10.c new file +347 -0
347 lines not on this page · raw message
Signature · 1 line
2.25.1
Quoted 24 lines · Johannes Cornelis Draaijer (datdenkikniet)
This patch adds a hwmon driver for the AHT10 Temperature and Humidity sensor. It has a maximum sample rate, as the datasheet states that the chip may heat up if it is sampled more than once every two seconds.
Has been tested a to work on a raspberrypi0w
Changes from v2:
Add reference to documentation toindex.rst
Properly align defines
Clamp value instead of returning error
Adjust return values
Remove unnecessary print, check and commentMajor changes from initial patch:
Removed devicetree/of references
Removedaht10_reset,aht10_remove
Add documentation
Switch to hwmon channels, attributes and info More appropriate usage of mutex
Return standard error codes
Add checking statements for errors that are returned Other code improvements as suggested
Quoted 1 line
Applied.
Thanks,
Guenter