mmc: mmci: Add bindings to operate CMD, CK, CKIN pins as GPIO
Subsystems (5)
PATCH v2 1/4 mmc: mmci: Add bindings to operate CMD, CK, CKIN pins as GPIO
Add DT bindings to describe GPIO line associated with CMD, CK, CKIN pins.
---
V2: Rebase on next-20210122
--- .../devicetree/bindings/mmc/arm,pl18x.yaml | 20 +++++++++++++++++++ 1 file changed, 20 insertions(+)
Documentation/devicetree/bindings/mmc/arm,pl18x.yaml +20 -0
@@ -127,6 +127,26 @@ properties: driver to sample the receive data (for example with a voltage switch transceiver). + st,cmd-gpios: + maxItems: 1 + description: + The GPIO matching the CMD pin. + + st,ck-gpios: + maxItems: 1 + description: + The GPIO matching the CK pin. + + st,ckin-gpios: + maxItems: 1 + description: + The GPIO matching the CKIN pin. + +dependencies: + st,cmd-gpios: [ "st,use-ckin" ] + st,ck-gpios: [ "st,use-ckin" ] + st,ckin-gpios: [ "st,use-ckin" ] + unevaluatedProperties: false required:
Signature · 1 line
2.29.2
PATCH v2 2/4 mmc: mmci: Add support for probing bus voltage level translator
Add support for testing whether bus voltage level translator is present and operational. This is useful on systems where the bus voltage level translator is optional, as the translator can be auto-detected by the driver and the feedback clock functionality can be disabled if it is not present.
This requires additional pinmux state, "init", where the CMD, CK, CKIN lines are not configured, so they can be claimed as GPIOs early on in probe(). The translator test sets CMD high to avoid interfering with a card, and then verifies whether signal set on CK is detected on CKIN. If the signal is detected, translator is present, otherwise the CKIN feedback clock are disabled.
---
V2: Rebase on next-20210122, add TB and RB
--- drivers/mmc/host/mmci.c | 70 ++++++++++++++++++++++++++++++++++++++--- 1 file changed, 65 insertions(+), 5 deletions(-)
drivers/mmc/host/mmci.c +65 -5
@@ -36,6 +36,7 @@#include <linux/types.h> #include <linux/pinctrl/consumer.h> #include <linux/reset.h> +#include <linux/gpio/consumer.h> #include <asm/div64.h> #include <asm/io.h>
@@ -1888,6 +1889,65 @@ static struct mmc_host_ops mmci_ops = { .start_signal_voltage_switch = mmci_sig_volt_switch, }; +static void mmci_probe_level_translator (struct mmc_host *mmc) +{ +struct device *dev =mmc_dev (mmc); +struct mmci_host *host =mmc_priv (mmc); +struct gpio_desc *cmd_gpio; +struct gpio_desc *ck_gpio; +struct gpio_desc *ckin_gpio; +int clk_hi, clk_lo; + +/* +* Assume the level translator is present if st,use-ckin is set. +* This is to cater for DTs which do not implement this test. +*/ + host->clk_reg_add |=MCI_STM32_CLK_SELCKIN ; + + cmd_gpio =gpiod_get (dev,"st,cmd" ,GPIOD_OUT_HIGH ); +if (IS_ERR (cmd_gpio)) + goto exit_cmd; + + ck_gpio =gpiod_get (dev,"st,ck" ,GPIOD_OUT_HIGH ); +if (IS_ERR (ck_gpio)) + goto exit_ck; + + ckin_gpio =gpiod_get (dev,"st,ckin" ,GPIOD_IN ); +if (IS_ERR (ckin_gpio)) + goto exit_ckin; + +/* All GPIOs are valid, test whether level translator works */ + +/* Sample CKIN */ + clk_hi = !!gpiod_get_value (ckin_gpio); + +/* Set CK low */ +gpiod_set_value (ck_gpio,0 ); + +/* Sample CKIN */ + clk_lo = !!gpiod_get_value (ckin_gpio); + +/* Tristate all */ +gpiod_direction_input (cmd_gpio); +gpiod_direction_input (ck_gpio); + +/* Level translator is present if CK signal is propagated to CKIN */ +if (!clk_hi || clk_lo) { + host->clk_reg_add &= ~MCI_STM32_CLK_SELCKIN ; +dev_warn (dev, +"Level translator inoperable, CK signal not detected on CKIN, disabling.\n" ); + } + +gpiod_put (ckin_gpio); + +exit_ckin: +gpiod_put (ck_gpio); +exit_ck: +gpiod_put (cmd_gpio); +exit_cmd: +pinctrl_select_default_state (dev); +} +static int mmci_of_parse (struct device_node *np,struct mmc_host *mmc) {struct mmci_host *host =mmc_priv (mmc);
@@ -1913,7 +1973,7 @@ static int mmci_of_parse(struct device_node *np, struct mmc_host *mmc)if (of_get_property (np,"st,neg-edge" ,NULL )) host->clk_reg_add |=MCI_STM32_CLK_NEGEDGE ;if (of_get_property (np,"st,use-ckin" ,NULL )) - host->clk_reg_add |=MCI_STM32_CLK_SELCKIN ; +mmci_probe_level_translator (mmc);if (of_get_property (np,"mmc-cap-mmc-highspeed" ,NULL )) mmc->caps |=MMC_CAP_MMC_HIGHSPEED ;
@@ -1949,15 +2009,15 @@ static int mmci_probe(struct amba_device *dev,if (!mmc)return -ENOMEM ; - ret =mmci_of_parse (np, mmc); -if (ret) - goto host_free; - host =mmc_priv (mmc); host->mmc = mmc; host->mmc_ops = &mmci_ops; mmc->ops = &mmci_ops; + ret =mmci_of_parse (np, mmc); +if (ret) + goto host_free; +/* * Some variant (STM32) doesn't have opendrain bit, nevertheless * pins can be set accordingly using pinctrl
Signature · 1 line
2.29.2
Re: [PATCH V2 2/4] mmc: mmci: Add support for probing bus voltage level translator
Quoted 14 lines · Marek Vasut
Add support for testing whether bus voltage level translator is present and operational. This is useful on systems where the bus voltage level translator is optional, as the translator can be auto-detected by the driver and the feedback clock functionality can be disabled if it is not present.
This requires additional pinmux state, "init", where the CMD, CK, CKIN lines are not configured, so they can be claimed as GPIOs early on in
probe(). The translator test sets CMD high to avoid interfering with a card, and then verifies whether signal set on CK is detected on CKIN. If the signal is detected, translator is present, otherwise the CKIN feedback clock are disabled.
Quoted 8 lines
Tested-by Yann Gautier <[email protected]>Reviewed-by Linus Walleij <[email protected]>Signed-off-by Marek Vasut <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Linus Walleij <[email protected]>Cc Ludovic Barre <[email protected]>Cc Ulf Hansson <[email protected]>
Applied for next, thanks!
Kind regards
Uffe
Quoted 116 lines
---
V2: Rebase on next-20210122, add TB and RB--- drivers/mmc/host/mmci.c | 70 ++++++++++++++++++++++++++++++++++++++--- 1 file changed, 65 insertions(+), 5 deletions(-)drivers/mmc/host/mmci.c +65
-6@@ -36,6 +36,7 @@#include <linux/types.h> #include <linux/pinctrl/consumer.h> #include <linux/reset.h> +#include <linux/gpio/consumer.h> #include <asm/div64.h> #include <asm/io.h> @@ -1888,6 +1889,65 @@ static struct mmc_host_ops mmci_ops = { .start_signal_voltage_switch = mmci_sig_volt_switch, }; +static void mmci_probe_level_translator (struct mmc_host *mmc) +{ +struct device *dev =mmc_dev (mmc); +struct mmci_host *host =mmc_priv (mmc); +struct gpio_desc *cmd_gpio; +struct gpio_desc *ck_gpio; +struct gpio_desc *ckin_gpio; +int clk_hi, clk_lo; + +/* +* Assume the level translator is present if st,use-ckin is set. +* This is to cater for DTs which do not implement this test. +*/ + host->clk_reg_add |=MCI_STM32_CLK_SELCKIN ; + + cmd_gpio =gpiod_get (dev,"st,cmd" ,GPIOD_OUT_HIGH ); +if (IS_ERR (cmd_gpio)) + goto exit_cmd; + + ck_gpio =gpiod_get (dev,"st,ck" ,GPIOD_OUT_HIGH ); +if (IS_ERR (ck_gpio)) + goto exit_ck; + + ckin_gpio =gpiod_get (dev,"st,ckin" ,GPIOD_IN ); +if (IS_ERR (ckin_gpio)) + goto exit_ckin; + +/* All GPIOs are valid, test whether level translator works */ + +/* Sample CKIN */ + clk_hi = !!gpiod_get_value (ckin_gpio); + +/* Set CK low */ +gpiod_set_value (ck_gpio,0 ); + +/* Sample CKIN */ + clk_lo = !!gpiod_get_value (ckin_gpio); + +/* Tristate all */ +gpiod_direction_input (cmd_gpio); +gpiod_direction_input (ck_gpio); + +/* Level translator is present if CK signal is propagated to CKIN */ +if (!clk_hi || clk_lo) { + host->clk_reg_add &= ~MCI_STM32_CLK_SELCKIN ; +dev_warn (dev, +"Level translator inoperable, CK signal not detected on CKIN, disabling.\n" ); + } + +gpiod_put (ckin_gpio); + +exit_ckin: +gpiod_put (ck_gpio); +exit_ck: +gpiod_put (cmd_gpio); +exit_cmd: +pinctrl_select_default_state (dev); +} +static int mmci_of_parse (struct device_node *np,struct mmc_host *mmc) {struct mmci_host *host =mmc_priv (mmc);@@ -1913,7 +1973,7 @@ static int mmci_of_parse(struct device_node *np, struct mmc_host *mmc)if (of_get_property (np,"st,neg-edge" ,NULL )) host->clk_reg_add |=MCI_STM32_CLK_NEGEDGE ;if (of_get_property (np,"st,use-ckin" ,NULL )) - host->clk_reg_add |=MCI_STM32_CLK_SELCKIN ; +mmci_probe_level_translator (mmc);if (of_get_property (np,"mmc-cap-mmc-highspeed" ,NULL )) mmc->caps |=MMC_CAP_MMC_HIGHSPEED ;@@ -1949,15 +2009,15 @@ static int mmci_probe(struct amba_device *dev,if (!mmc)return -ENOMEM ; - ret =mmci_of_parse (np, mmc); -if (ret) - goto host_free; - host =mmc_priv (mmc); host->mmc = mmc; host->mmc_ops = &mmci_ops; mmc->ops = &mmci_ops; + ret =mmci_of_parse (np, mmc); +if (ret) + goto host_free; +/* * Some variant (STM32) doesn't have opendrain bit, nevertheless * pins can be set accordingly using pinctrl -- 2.29.2
PATCH v2 3/4 ARM: dts: stm32: Add additional init state for SDMMC1 pins
In reply to Marek VasutAdd "init" mux option for SDMMC1, where the CMD, CK, CKIN lines are not configured, so they can be claimed as GPIOs early on in driver probe(). This is used for probing optional voltage level translator.
---
V2: Rebase on next-20210122
--- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +23 -0
@@ -1385,6 +1385,18 @@ pins { }; }; + sdmmc1_b4_init_pins_a: sdmmc1-b4-init-0 { + pins1 { + pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ + <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ + <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ + <STM32_PINMUX('C', 11, AF12)>; /* SDMMC1_D3 */ + slew-rate = <1>; + drive-push-pull; + bias-disable; + }; + }; + sdmmc1_dir_pins_a: sdmmc1-dir-0 { pins1 { pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
@@ -1409,6 +1421,17 @@ pins { }; }; + sdmmc1_dir_init_pins_a: sdmmc1-dir-init-0 { + pins1 { + pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */ + <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */ + <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */ + slew-rate = <1>; + drive-push-pull; + bias-pull-up; + }; + }; + sdmmc1_dir_pins_b: sdmmc1-dir-1 { pins1 { pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
Signature · 1 line
2.29.2
PATCH v2 4/4 ARM: dts: stm32: Enable voltage translator auto-detection on DHCOM
In reply to Marek VasutThe DHCOM SoM uSD slot has an optional voltage level translator, add DT bindings which permit the MMCI driver to detect the translator automatically.
---
V2: Rebase on next-20210122
--- arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi +6 -1
@@ -408,14 +408,19 @@ &rtc { }; &sdmmc1 { - pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-names = "default", "opendrain", "sleep", "init"; pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>; pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>; + pinctrl-3 = <&sdmmc1_b4_init_pins_a &sdmmc1_dir_init_pins_a>; cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; disable-wp; st,sig-dir; st,neg-edge; + st,use-ckin; + st,cmd-gpios = <&gpiod 2 0>; + st,ck-gpios = <&gpioc 12 0>; + st,ckin-gpios = <&gpioe 4 0>; bus-width = <4>; vmmc-supply = <&vdd_sd>; status = "okay";
Signature · 1 line
2.29.2
Alexandre TORGUE
maintainerRe: [PATCH V2 4/4] ARM: dts: stm32: Enable voltage translator auto-detection on DHCOM
Hi Marek
Quoted 32 lines · Marek Vasut
The DHCOM SoM uSD slot has an optional voltage level translator, add DT bindings which permit the MMCI driver to detect the translator automatically.
Signed-off-by Marek Vasut <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Linus Walleij <[email protected]>Cc Ludovic Barre <[email protected]>Cc Ulf Hansson <[email protected]>---
V2: Rebase on next-20210122--- arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi +2
-1@@ -408,14 +408,19 @@ &rtc { }; &sdmmc1 { - pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-names = "default", "opendrain", "sleep", "init"; pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>; pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>; + pinctrl-3 = <&sdmmc1_b4_init_pins_a &sdmmc1_dir_init_pins_a>; cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi &rtc { · line 426
Quoted 10 lines
arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi +4
-0disable-wp; st,sig-dir; st,neg-edge; + st,use-ckin; + st,cmd-gpios = <&gpiod 2 0>; + st,ck-gpios = <&gpioc 12 0>; + st,ckin-gpios = <&gpioe 4 0>; bus-width = <4>; vmmc-supply = <&vdd_sd>; status = "okay";
DT patches applied on stm32-next.
Thanks
Alex
Quoted 10 lines · Marek Vasut
Add DT bindings to describe GPIO line associated with CMD, CK, CKIN pins.
Signed-off-by Marek Vasut <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Linus Walleij <[email protected]>Cc Ludovic Barre <[email protected]>Cc Rob Herring <[email protected]>Cc Ulf Hansson <[email protected]>
Quoted 2 lines
---
V2: Rebase on next-20210122
I would probably add an example as well, but that can be done separately and isn't super-important.
Yours,
Linus Walleij
Quoted 11 lines · Marek Vasut
Add DT bindings to describe GPIO line associated with CMD, CK, CKIN pins.
Signed-off-by Marek Vasut <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Linus Walleij <[email protected]>Cc Ludovic Barre <[email protected]>Cc Rob Herring <[email protected]>Cc Ulf Hansson <[email protected]>
Applied for next, thanks!
Kind regards
Uffe
Quoted 40 lines
---
V2: Rebase on next-20210122--- .../devicetree/bindings/mmc/arm,pl18x.yaml | 20 +++++++++++++++++++ 1 file changed, 20 insertions(+)Documentation/devicetree/bindings/mmc/arm,pl18x.yaml +20
-1@@ -127,6 +127,26 @@ properties: driver to sample the receive data (for example with a voltage switch transceiver). + st,cmd-gpios: + maxItems: 1 + description: + The GPIO matching the CMD pin. + + st,ck-gpios: + maxItems: 1 + description: + The GPIO matching the CK pin. + + st,ckin-gpios: + maxItems: 1 + description: + The GPIO matching the CKIN pin. + +dependencies: + st,cmd-gpios: [ "st,use-ckin" ] + st,ck-gpios: [ "st,use-ckin" ] + st,ckin-gpios: [ "st,use-ckin" ] + unevaluatedProperties: false required: --2.29.2