Add initial support for BQ Aquaris X5
v2 cover Add initial support for BQ Aquaris X5
v2:
- reorder I2C devices sorting them by address
v1:
- initial patch submission
https://lore.kernel.org/linux-arm-msm/[email protected]/
Aquaris X5 (Longcheer L8910) is a smartphone released by BQ in 2015.
As part of msm8916-mainline project, this series aims to bring initial mainline support for it.
Features added:
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- Regulators
- WiFi/BT
- Volume buttons
- Vibrator
- Touchkeys backlight
- Accelerometer and gyroscope sensor
- Magnetometer sensor
Jonathan Albrieux (3):
arm64: dts: qcom: Add device tree for BQ Aquaris X5 (Longcheer L8910)
arm64: dts: qcom: msm8916: Add blsp_i2c3
arm64: dts: qcom: msm8916-longcheer-l8910: Add imu/magnetometer
arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8916-longcheer-l8910.dts | 267 ++++++++++++++++++ arch/arm64/boot/dts/qcom/msm8916-pins.dtsi | 16 ++ arch/arm64/boot/dts/qcom/msm8916.dtsi | 15 + 4 files changed, 299 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
Signature · 1 line
2.17.1
PATCH v2 1/3 arm64: dts: qcom: Add device tree for BQ Aquaris X5 (Longcheer L8910)
BQ Aquaris X5 (Longcheer L8910) is a smartphone using the MSM8916 SoC.
Add device tree with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- Regulators
- WiFi/BT
- Volume buttons
- Vibrator
- Touchkeys backlight
This device tree is based on downstream device tree from BQ and from Longcheer L8915 device tree.
--- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8916-longcheer-l8910.dts | 230 ++++++++++++++++++ 2 files changed, 231 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
arch/arm64/boot/dts/qcom/Makefile +1 -0
@@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8910.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a3u-eur.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a5u-eur.dtb
arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts new file +230 -0
230 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v2 2/3 arm64: dts: qcom: msm8916: Add blsp_i2c3
In reply to Jonathan AlbrieuxMSM8916 has another I2C QUP controller that can be enabled on GPIO 10 and 11.
Add blsp_i2c3 to msm8916.dtsi and disable it by default.
--- arch/arm64/boot/dts/qcom/msm8916-pins.dtsi | 16 ++++++++++++++++ arch/arm64/boot/dts/qcom/msm8916.dtsi | 15 +++++++++++++++ 2 files changed, 31 insertions(+)
arch/arm64/boot/dts/qcom/msm8916-pins.dtsi +16 -0
@@ -220,6 +220,22 @@ bias-disable; }; + i2c3_default: i2c3-default { + pins = "gpio10", "gpio11"; + function = "blsp_i2c3"; + + drive-strength = <2>; + bias-disable; + }; + + i2c3_sleep: i2c3-sleep { + pins = "gpio10", "gpio11"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + i2c4_default: i2c4-default { pins = "gpio14", "gpio15"; function = "blsp_i2c4";
arch/arm64/boot/dts/qcom/msm8916.dtsi +15 -0
@@ -1528,6 +1528,21 @@ status = "disabled"; }; + blsp_i2c3: i2c@78b7000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b7000 0x500>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>; + clock-names = "iface", "core"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c3_default>; + pinctrl-1 = <&i2c3_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + blsp_spi3: spi@78b7000 { compatible = "qcom,spi-qup-v2.2.1"; reg = <0x078b7000 0x500>;
Signature · 1 line
2.17.1
PATCH v2 3/3 arm64: dts: qcom: msm8916-longcheer-l8910: Add imu/magnetometer
In reply to Jonathan AlbrieuxBQ Aquaris X5 (Longcheer L8910) has:
- BMI160 accelerometer and gyroscope sensor
- AK09911 magnetometer sensor
Add them to the device tree.
This patch depends on patch "arm64: dts: qcom: msm8916: Add blsp_i2c3".
--- .../boot/dts/qcom/msm8916-longcheer-l8910.dts | 37 +++++++++++++++++++ 1 file changed, 37 insertions(+)
arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts +37 -0
@@ -56,6 +56,35 @@ }; }; +&blsp_i2c3 { + status = "okay"; + + magnetometer@d { + compatible = "asahi-kasei,ak09911"; + reg = <0x0d>; + + vdd-supply = <&pm8916_l17>; + vid-supply = <&pm8916_l6>; + + reset-gpios = <&msmgpio 111 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&mag_reset_default>; + }; + + imu@68 { + compatible = "bosch,bmi160"; + reg = <0x68>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + + mount-matrix = "0", "1", "0", + "-1", "0", "0", + "0", "0", "1"; + }; +}; + &blsp1_uart2 { status = "okay"; };
@@ -220,6 +249,14 @@ bias-pull-up; }; + mag_reset_default: mag-reset-default { + pins = "gpio111"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + usb_id_default: usb-id-default { pins = "gpio110"; function = "gpio";
Signature · 1 line
2.17.1
Re: [PATCH v2 3/3] arm64: dts: qcom: msm8916-longcheer-l8910: Add imu/magnetometer
Quoted 8 lines · Jonathan Albrieux
BQ Aquaris X5 (Longcheer L8910) has:
- BMI160 accelerometer and gyroscope sensor
- AK09911 magnetometer sensor
Add them to the device tree.This patch depends on patch "arm64: dts: qcom: msm8916: Add
blsp_i2c3".Signed-off-by Jonathan Albrieux <[email protected]>
Quoted 62 lines
--- .../boot/dts/qcom/msm8916-longcheer-l8910.dts | 37 +++++++++++++++++++ 1 file changed, 37 insertions(+)arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts +37
-0@@ -56,6 +56,35 @@ }; }; +&blsp_i2c3 { + status = "okay"; + + magnetometer@d { + compatible = "asahi-kasei,ak09911"; + reg = <0x0d>; + + vdd-supply = <&pm8916_l17>; + vid-supply = <&pm8916_l6>; + + reset-gpios = <&msmgpio 111 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&mag_reset_default>; + }; + + imu@68 { + compatible = "bosch,bmi160"; + reg = <0x68>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + + mount-matrix = "0", "1", "0", + "-1", "0", "0", + "0", "0", "1"; + }; +}; + &blsp1_uart2 { status = "okay"; };@@ -220,6 +249,14 @@ bias-pull-up; }; + mag_reset_default: mag-reset-default { + pins = "gpio111"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + usb_id_default: usb-id-default { pins = "gpio110"; function = "gpio";Signature · 1 line
2.17.1