Skip to contentSkip to conversation

i2c-imx.c: Synthesize end of transaction events without idle interrupts

PATCH Applied Kevin Paul Herbert 3 participants 6 messages Dec 22, 2020 – Feb 1, 2021

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 i2c-imx.c: Synthesize end of transaction events without idle interrupts

Only the Layerscape SoCs have interrupts on bus idle, which facilitate sending events which complete slave bus transactions.

Add support for synthesizing missing events. If we see a master request, or a newly addressed slave request, if the last event sent to the backend was I2C_SLAVE_READ_REQUESTED, send the backend a I2C_SLAVE_READ_PROCESSED followed by I2C_SLAVE_STOP. For all other events, send an I2C_SLAVE_STOP.

---
 drivers/i2c/busses/i2c-imx.c | 59 +++++++++++++++++++++++++++++++-----
 1 file changed, 52 insertions(+), 7 deletions(-)
drivers/i2c/busses/i2c-imx.c +52 -7
index b444fbf1a262..b3e2a6a7fc19 100644
@@ -209,6 +209,7 @@ struct imx_i2c_struct {
 
 	struct imx_i2c_dma	*dma;
 	struct i2c_client	*slave;
+	enum i2c_slave_event last_slave_event;
 };
 
 static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
@@ -662,6 +663,36 @@ static void i2c_imx_enable_bus_idle(struct imx_i2c_struct *i2c_imx)
 	}
 }
 
+static void i2c_imx_slave_event(struct imx_i2c_struct *i2c_imx,
+				enum i2c_slave_event event, u8 *val)
+{
+	i2c_slave_event(i2c_imx->slave, event, val);
+	i2c_imx->last_slave_event = event;
+}
+
+static void i2c_imx_slave_finish_op(struct imx_i2c_struct *i2c_imx)
+{
+	u8 val;
+
+	while (i2c_imx->last_slave_event != I2C_SLAVE_STOP) {
+		switch (i2c_imx->last_slave_event) {
+		case I2C_SLAVE_READ_REQUESTED:
+			i2c_imx_slave_event(i2c_imx, I2C_SLAVE_READ_PROCESSED,
+					    &val);
+			break;
+
+		case I2C_SLAVE_WRITE_REQUESTED:
+		case I2C_SLAVE_READ_PROCESSED:
+		case I2C_SLAVE_WRITE_RECEIVED:
+			i2c_imx_slave_event(i2c_imx, I2C_SLAVE_STOP, &val);
+			break;
+
+		case I2C_SLAVE_STOP:
+			break;
+		}
+	}
+}
+
 static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
 				     unsigned int status, unsigned int ctl)
 {
@@ -674,9 +705,11 @@ static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
 	}
 
 	if (status & I2SR_IAAS) { /* Addressed as a slave */
+		i2c_imx_slave_finish_op(i2c_imx);
 		if (status & I2SR_SRW) { /* Master wants to read from us*/
 			dev_dbg(&i2c_imx->adapter.dev, "read requested");
-			i2c_slave_event(i2c_imx->slave, I2C_SLAVE_READ_REQUESTED, &value);
+			i2c_imx_slave_event(i2c_imx,
+					    I2C_SLAVE_READ_REQUESTED, &value);
 
 			/* Slave transmit */
 			ctl |= I2CR_MTX;
@@ -686,7 +719,8 @@ static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
 			imx_i2c_write_reg(value, i2c_imx, IMX_I2C_I2DR);
 		} else { /* Master wants to write to us */
 			dev_dbg(&i2c_imx->adapter.dev, "write requested");
-			i2c_slave_event(i2c_imx->slave,	I2C_SLAVE_WRITE_REQUESTED, &value);
+			i2c_imx_slave_event(i2c_imx,
+					    I2C_SLAVE_WRITE_REQUESTED, &value);
 
 			/* Slave receive */
 			ctl &= ~I2CR_MTX;
@@ -697,17 +731,20 @@ static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
 	} else if (!(ctl & I2CR_MTX)) { /* Receive mode */
 		if (status & I2SR_IBB) { /* No STOP signal detected */
 			value = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
-			i2c_slave_event(i2c_imx->slave,	I2C_SLAVE_WRITE_RECEIVED, &value);
+			i2c_imx_slave_event(i2c_imx,
+					    I2C_SLAVE_WRITE_RECEIVED, &value);
 		} else { /* STOP signal is detected */
 			dev_dbg(&i2c_imx->adapter.dev,
 				"STOP signal detected");
-			i2c_slave_event(i2c_imx->slave, I2C_SLAVE_STOP, &value);
+			i2c_imx_slave_event(i2c_imx,
+					    I2C_SLAVE_STOP, &value);
 		}
 	} else if (!(status & I2SR_RXAK)) { /* Transmit mode received ACK */
 		ctl |= I2CR_MTX;
 		imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
 
-		i2c_slave_event(i2c_imx->slave,	I2C_SLAVE_READ_PROCESSED, &value);
+		i2c_imx_slave_event(i2c_imx,
+				    I2C_SLAVE_READ_PROCESSED, &value);
 
 		imx_i2c_write_reg(value, i2c_imx, IMX_I2C_I2DR);
 	} else { /* Transmit mode received NAK */
@@ -748,6 +785,7 @@ static int i2c_imx_reg_slave(struct i2c_client *client)
 		return -EBUSY;
 
 	i2c_imx->slave = client;
+	i2c_imx->last_slave_event = I2C_SLAVE_STOP;
 
 	/* Resume */
 	ret = pm_runtime_get_sync(i2c_imx->adapter.dev.parent);
@@ -800,10 +838,17 @@ static irqreturn_t i2c_imx_isr(int irq, void *dev_id)
 
 	status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
 	ctl = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
+
 	if (status & I2SR_IIF) {
 		i2c_imx_clear_irq(i2c_imx, I2SR_IIF);
-		if (i2c_imx->slave && !(ctl & I2CR_MSTA))
-			return i2c_imx_slave_isr(i2c_imx, status, ctl);
+		if (i2c_imx->slave) {
+			if (!(ctl & I2CR_MSTA)) {
+				return i2c_imx_slave_isr(i2c_imx, status, ctl);
+			} else if (i2c_imx->last_slave_event !=
+				   I2C_SLAVE_STOP) {
+				i2c_imx_slave_finish_op(i2c_imx);
+			}
+		}
 		return i2c_imx_master_isr(i2c_imx, status);
 	}
 
Signature · 1 line
2.25.1
maintainer
#1 lore raw

Hi Kevin Paul,

Quoted 48 lines · Kevin Paul Herbert

Only the Layerscape SoCs have interrupts on bus idle, which facilitate sending events which complete slave bus transactions.

Add support for synthesizing missing events. If we see a master request, or a newly addressed slave request, if the last event sent to the backend was I2C_SLAVE_READ_REQUESTED, send the backend a I2C_SLAVE_READ_PROCESSED followed by I2C_SLAVE_STOP. For all other events, send an I2C_SLAVE_STOP.

---
 drivers/i2c/busses/i2c-imx.c | 59 +++++++++++++++++++++++++++++++-----
 1 file changed, 52 insertions(+), 7 deletions(-)
drivers/i2c/busses/i2c-imx.c +20 -0
index b444fbf1a262..b3e2a6a7fc19 100644
@@ -209,6 +209,7 @@ struct imx_i2c_struct {
 
 	struct imx_i2c_dma	*dma;
 	struct i2c_client	*slave;
+	enum i2c_slave_event last_slave_event;
 };
 
 static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
@@ -662,6 +663,36 @@ static void i2c_imx_enable_bus_idle(struct imx_i2c_struct *i2c_imx)
 	}
 }
 
+static void i2c_imx_slave_event(struct imx_i2c_struct *i2c_imx,
+				enum i2c_slave_event event, u8 *val)
+{
+	i2c_slave_event(i2c_imx->slave, event, val);
+	i2c_imx->last_slave_event = event;
+}
+
+static void i2c_imx_slave_finish_op(struct imx_i2c_struct *i2c_imx)
+{
+	u8 val;
+
+	while (i2c_imx->last_slave_event != I2C_SLAVE_STOP) {
+		switch (i2c_imx->last_slave_event) {
+		case I2C_SLAVE_READ_REQUESTED:
+			i2c_imx_slave_event(i2c_imx, I2C_SLAVE_READ_PROCESSED,
+					    &val);
+			break;
+
+		case I2C_SLAVE_WRITE_REQUESTED:

drivers/i2c/busses/i2c-imx.c static void i2c_imx_enable_bus_idle(struct imx_i2c_struct *i2c_imx) · line 694

Quoted 10 lines
drivers/i2c/busses/i2c-imx.c +10 -0
+		case I2C_SLAVE_READ_PROCESSED:
+		case I2C_SLAVE_WRITE_RECEIVED:
+			i2c_imx_slave_event(i2c_imx, I2C_SLAVE_STOP, &val);
+			break;
+
+		case I2C_SLAVE_STOP:
+			break;
+		}
+	}
+}

Is it really working code?

The i2c_imx_slave_finish_op() is a waiting busy loop withing an IRQ! And it is waiting for an event, which is updated in the same IRQ callback. Or am i missing some thing?

Regards,
Oleksij

Quoted 87 lines
drivers/i2c/busses/i2c-imx.c +21 -7
 static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
 				     unsigned int status, unsigned int ctl)
 {
@@ -674,9 +705,11 @@ static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
 	}
 
 	if (status & I2SR_IAAS) { /* Addressed as a slave */
+		i2c_imx_slave_finish_op(i2c_imx);
 		if (status & I2SR_SRW) { /* Master wants to read from us*/
 			dev_dbg(&i2c_imx->adapter.dev, "read requested");
-			i2c_slave_event(i2c_imx->slave, I2C_SLAVE_READ_REQUESTED, &value);
+			i2c_imx_slave_event(i2c_imx,
+					    I2C_SLAVE_READ_REQUESTED, &value);
 
 			/* Slave transmit */
 			ctl |= I2CR_MTX;
@@ -686,7 +719,8 @@ static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
 			imx_i2c_write_reg(value, i2c_imx, IMX_I2C_I2DR);
 		} else { /* Master wants to write to us */
 			dev_dbg(&i2c_imx->adapter.dev, "write requested");
-			i2c_slave_event(i2c_imx->slave,	I2C_SLAVE_WRITE_REQUESTED, &value);
+			i2c_imx_slave_event(i2c_imx,
+					    I2C_SLAVE_WRITE_REQUESTED, &value);
 
 			/* Slave receive */
 			ctl &= ~I2CR_MTX;
@@ -697,17 +731,20 @@ static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
 	} else if (!(ctl & I2CR_MTX)) { /* Receive mode */
 		if (status & I2SR_IBB) { /* No STOP signal detected */
 			value = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
-			i2c_slave_event(i2c_imx->slave,	I2C_SLAVE_WRITE_RECEIVED, &value);
+			i2c_imx_slave_event(i2c_imx,
+					    I2C_SLAVE_WRITE_RECEIVED, &value);
 		} else { /* STOP signal is detected */
 			dev_dbg(&i2c_imx->adapter.dev,
 				"STOP signal detected");
-			i2c_slave_event(i2c_imx->slave, I2C_SLAVE_STOP, &value);
+			i2c_imx_slave_event(i2c_imx,
+					    I2C_SLAVE_STOP, &value);
 		}
 	} else if (!(status & I2SR_RXAK)) { /* Transmit mode received ACK */
 		ctl |= I2CR_MTX;
 		imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
 
-		i2c_slave_event(i2c_imx->slave,	I2C_SLAVE_READ_PROCESSED, &value);
+		i2c_imx_slave_event(i2c_imx,
+				    I2C_SLAVE_READ_PROCESSED, &value);
 
 		imx_i2c_write_reg(value, i2c_imx, IMX_I2C_I2DR);
 	} else { /* Transmit mode received NAK */
@@ -748,6 +785,7 @@ static int i2c_imx_reg_slave(struct i2c_client *client)
 		return -EBUSY;
 
 	i2c_imx->slave = client;
+	i2c_imx->last_slave_event = I2C_SLAVE_STOP;
 
 	/* Resume */
 	ret = pm_runtime_get_sync(i2c_imx->adapter.dev.parent);
@@ -800,10 +838,17 @@ static irqreturn_t i2c_imx_isr(int irq, void *dev_id)
 
 	status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
 	ctl = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
+
 	if (status & I2SR_IIF) {
 		i2c_imx_clear_irq(i2c_imx, I2SR_IIF);
-		if (i2c_imx->slave && !(ctl & I2CR_MSTA))
-			return i2c_imx_slave_isr(i2c_imx, status, ctl);
+		if (i2c_imx->slave) {
+			if (!(ctl & I2CR_MSTA)) {
+				return i2c_imx_slave_isr(i2c_imx, status, ctl);
+			} else if (i2c_imx->last_slave_event !=
+				   I2C_SLAVE_STOP) {
+				i2c_imx_slave_finish_op(i2c_imx);
+			}
+		}
 		return i2c_imx_master_isr(i2c_imx, status);
 	}
 
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Signature · 4 lines
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#2 lore raw

The loop sends either one or two events to the slave driver. If the state is I2C_SLAVE_READ_REQUESTED, we synthesize the I2C_SLAVE_READ_PROCESSED event, and then our state becomes I2C_SLAVE_READ_PROCESSED. In all other states, we transition to I2C_SLAVE_STOP and exit the loop.

It is not a busy loop at all. It is calling the callback handler (that already expects to be in IRQ context) one or two times, and then it exits the loop.

Kevin

Quoted 165 lines · Oleksij Rempel

Hi Kevin Paul,

Quoted 48 lines · Kevin Paul Herbert

Only the Layerscape SoCs have interrupts on bus idle, which facilitate sending events which complete slave bus transactions.

Add support for synthesizing missing events. If we see a master request, or a newly addressed slave request, if the last event sent to the backend was I2C_SLAVE_READ_REQUESTED, send the backend a I2C_SLAVE_READ_PROCESSED followed by I2C_SLAVE_STOP. For all other events, send an I2C_SLAVE_STOP.

---
 drivers/i2c/busses/i2c-imx.c | 59 +++++++++++++++++++++++++++++++-----
 1 file changed, 52 insertions(+), 7 deletions(-)
drivers/i2c/busses/i2c-imx.c +20 -0
index b444fbf1a262..b3e2a6a7fc19 100644
@@ -209,6 +209,7 @@ struct imx_i2c_struct {
 
      struct imx_i2c_dma      *dma;
      struct i2c_client       *slave;
+     enum i2c_slave_event last_slave_event;
 };
 
 static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
@@ -662,6 +663,36 @@ static void i2c_imx_enable_bus_idle(struct imx_i2c_struct *i2c_imx)
      }
 }
 
+static void i2c_imx_slave_event(struct imx_i2c_struct *i2c_imx,
+                             enum i2c_slave_event event, u8 *val)
+{
+     i2c_slave_event(i2c_imx->slave, event, val);
+     i2c_imx->last_slave_event = event;
+}
+
+static void i2c_imx_slave_finish_op(struct imx_i2c_struct *i2c_imx)
+{
+     u8 val;
+
+     while (i2c_imx->last_slave_event != I2C_SLAVE_STOP) {
+             switch (i2c_imx->last_slave_event) {
+             case I2C_SLAVE_READ_REQUESTED:
+                     i2c_imx_slave_event(i2c_imx, I2C_SLAVE_READ_PROCESSED,
+                                         &val);
+                     break;
+
+             case I2C_SLAVE_WRITE_REQUESTED:

drivers/i2c/busses/i2c-imx.c static void i2c_imx_enable_bus_idle(struct imx_i2c_struct *i2c_imx) · line 694

Quoted 10 lines
drivers/i2c/busses/i2c-imx.c +10 -0
+             case I2C_SLAVE_READ_PROCESSED:
+             case I2C_SLAVE_WRITE_RECEIVED:
+                     i2c_imx_slave_event(i2c_imx, I2C_SLAVE_STOP, &val);
+                     break;
+
+             case I2C_SLAVE_STOP:
+                     break;
+             }
+     }
+}

Is it really working code?

The i2c_imx_slave_finish_op() is a waiting busy loop withing an IRQ! And it is waiting for an event, which is updated in the same IRQ callback. Or am i missing some thing?

Regards,
Oleksij

Quoted 82 lines
drivers/i2c/busses/i2c-imx.c +21 -8
 static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
                                   unsigned int status, unsigned int ctl)
 {
@@ -674,9 +705,11 @@ static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
      }
 
      if (status & I2SR_IAAS) { /* Addressed as a slave */
+             i2c_imx_slave_finish_op(i2c_imx);
              if (status & I2SR_SRW) { /* Master wants to read from us*/
                      dev_dbg(&i2c_imx->adapter.dev, "read requested");
-                     i2c_slave_event(i2c_imx->slave, I2C_SLAVE_READ_REQUESTED, &value);
+                     i2c_imx_slave_event(i2c_imx,
+                                         I2C_SLAVE_READ_REQUESTED, &value);
 
                      /* Slave transmit */
                      ctl |= I2CR_MTX;
@@ -686,7 +719,8 @@ static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
                      imx_i2c_write_reg(value, i2c_imx, IMX_I2C_I2DR);
              } else { /* Master wants to write to us */
                      dev_dbg(&i2c_imx->adapter.dev, "write requested");
-                     i2c_slave_event(i2c_imx->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+                     i2c_imx_slave_event(i2c_imx,
+                                         I2C_SLAVE_WRITE_REQUESTED, &value);
 
                      /* Slave receive */
                      ctl &= ~I2CR_MTX;
@@ -697,17 +731,20 @@ static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx,
      } else if (!(ctl & I2CR_MTX)) { /* Receive mode */
              if (status & I2SR_IBB) { /* No STOP signal detected */
                      value = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
-                     i2c_slave_event(i2c_imx->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
+                     i2c_imx_slave_event(i2c_imx,
+                                         I2C_SLAVE_WRITE_RECEIVED, &value);
              } else { /* STOP signal is detected */
                      dev_dbg(&i2c_imx->adapter.dev,
                              "STOP signal detected");
-                     i2c_slave_event(i2c_imx->slave, I2C_SLAVE_STOP, &value);
+                     i2c_imx_slave_event(i2c_imx,
+                                         I2C_SLAVE_STOP, &value);
              }
      } else if (!(status & I2SR_RXAK)) { /* Transmit mode received ACK */
              ctl |= I2CR_MTX;
              imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
 
-             i2c_slave_event(i2c_imx->slave, I2C_SLAVE_READ_PROCESSED, &value);
+             i2c_imx_slave_event(i2c_imx,
+                                 I2C_SLAVE_READ_PROCESSED, &value);
 
              imx_i2c_write_reg(value, i2c_imx, IMX_I2C_I2DR);
      } else { /* Transmit mode received NAK */
@@ -748,6 +785,7 @@ static int i2c_imx_reg_slave(struct i2c_client *client)
              return -EBUSY;
 
      i2c_imx->slave = client;
+     i2c_imx->last_slave_event = I2C_SLAVE_STOP;
 
      /* Resume */
      ret = pm_runtime_get_sync(i2c_imx->adapter.dev.parent);
@@ -800,10 +838,17 @@ static irqreturn_t i2c_imx_isr(int irq, void *dev_id)
 
      status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
      ctl = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
+
      if (status & I2SR_IIF) {
              i2c_imx_clear_irq(i2c_imx, I2SR_IIF);
-             if (i2c_imx->slave && !(ctl & I2CR_MSTA))
-                     return i2c_imx_slave_isr(i2c_imx, status, ctl);
+             if (i2c_imx->slave) {
+                     if (!(ctl & I2CR_MSTA)) {
+                             return i2c_imx_slave_isr(i2c_imx, status, ctl);
+                     } else if (i2c_imx->last_slave_event !=
+                                I2C_SLAVE_STOP) {
+                             i2c_imx_slave_finish_op(i2c_imx);
+                     }
+             }
              return i2c_imx_master_isr(i2c_imx, status);
      }
 
--

2.25.1

Quoted 5 lines

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

--

Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#3 lore raw
Quoted 9 lines · Kevin Herbert

The loop sends either one or two events to the slave driver. If the state is I2C_SLAVE_READ_REQUESTED, we synthesize the I2C_SLAVE_READ_PROCESSED event, and then our state becomes I2C_SLAVE_READ_PROCESSED. In all other states, we transition to I2C_SLAVE_STOP and exit the loop.

It is not a busy loop at all. It is calling the callback handler (that already expects to be in IRQ context) one or two times, and then it exits the loop.

Oleksij, does this answer your question?

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

maintainer Tested-by Acked-by
#4 lore raw
Quoted 7 lines · Wolfram Sang
Quoted 6 lines · Kevin Herbert

The loop sends either one or two events to the slave driver. If the state is I2C_SLAVE_READ_REQUESTED, we synthesize the I2C_SLAVE_READ_PROCESSED event, and then our state becomes I2C_SLAVE_READ_PROCESSED. In all other states, we transition to I2C_SLAVE_STOP and exit the loop.

Quoted 6 lines
Quoted 3 lines

It is not a busy loop at all. It is calling the callback handler (that already expects to be in IRQ context) one or two times, and then it exits the loop.

Oleksij, does this answer your question?

Sorry, I missed this email.

Kevin, thank you for the answer and the patch.

Regards,
Oleksij

Signature · 9 lines
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Applied
#5 lore raw
In reply to Kevin Paul Herbert
Quoted 9 lines · Kevin Paul Herbert

Only the Layerscape SoCs have interrupts on bus idle, which facilitate sending events which complete slave bus transactions.

Add support for synthesizing missing events. If we see a master request, or a newly addressed slave request, if the last event sent to the backend was I2C_SLAVE_READ_REQUESTED, send the backend a I2C_SLAVE_READ_PROCESSED followed by I2C_SLAVE_STOP. For all other events, send an I2C_SLAVE_STOP.

Applied to for-next, thanks!