Skip to contentSkip to conversation

ARM: dts: am335x-pocketbeagle: unique gpio-line-names

PATCH In review Drew Fustini 4 participants 11 messages Jan 27, 2021 – Mar 24, 2021

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 ARM: dts: am335x-pocketbeagle: unique gpio-line-names

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/

---
 arch/arm/boot/dts/am335x-pocketbeagle.dts | 140 +++++++++++-----------
 1 file changed, 70 insertions(+), 70 deletions(-)
arch/arm/boot/dts/am335x-pocketbeagle.dts +70 -70
index d526c5941c9b..209cdd17dc1e 100644
@@ -61,51 +61,51 @@ vmmcsd_fixed: fixedregulator0 {
 
 &gpio0 {
 	gpio-line-names =
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
 		"P1.08 [SPI0_CLK]",
 		"P1.10 [SPI0_MISO]",
 		"P1.12 [SPI0_MOSI]",
 		"P1.06 [SPI0_CS]",
 		"[MMC0_CD]",
 		"P2.29 [SPI1_CLK]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
+		"[SYSBOOT 12]",
+		"[SYSBOOT 13]",
+		"[SYSBOOT 14]",
+		"[SYSBOOT 15]",
 		"P1.26 [I2C2_SDA]",
 		"P1.28 [I2C2_SCL]",
 		"P2.11 [I2C1_SDA]",
 		"P2.09 [I2C1_SCL]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
+		"NC",
 		"P2.31 [SPI1_CS]",
 		"P1.20 [PRU0.16]",
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
 		"P2.03",
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
 		"P1.34",
 		"P2.19",
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
 		"P2.05 [UART4_RX]",
 		"P2.07 [UART4_TX]";
 };
 
 &gpio1 {
 	gpio-line-names =
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
 		"P2.25 [SPI1_MOSI]",
 		"P1.32 [UART0_RX]",
 		"P1.30 [UART0_TX]",
@@ -113,10 +113,10 @@ &gpio1 {
 		"P2.33",
 		"P2.22",
 		"P2.18",
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
 		"P2.01 [PWM1A]",
-		"[NC]",
+		"NC",
 		"P2.10",
 		"[USR LED 0]",
 		"[USR LED 1]",
@@ -126,35 +126,35 @@ &gpio1 {
 		"P2.04",
 		"P2.02",
 		"P2.08",
-		"[NC]",
-		"[NC]",
-		"[NC]";
+		"NC",
+		"NC",
+		"NC";
 };
 
 &gpio2 {
 	gpio-line-names =
 		"P2.20",
 		"P2.17",
-		"[NC]",
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
+		"NC",
 		"[EEPROM_WP]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[SYSBOOT]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
+		"[SYSBOOT 0]",
+		"[SYSBOOT 1]",
+		"[SYSBOOT 2]",
+		"[SYSBOOT 3]",
+		"[SYSBOOT 4]",
+		"[SYSBOOT 5]",
+		"[SYSBOOT 6]",
+		"[SYSBOOT 7]",
+		"[SYSBOOT 8]",
+		"[SYSBOOT 9]",
+		"[SYSBOOT 10]",
+		"[SYSBOOT 11]",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
 		"P2.35 [AIN5]",
 		"P1.02 [AIN6]",
 		"P1.35 [PRU1.10]",
@@ -169,19 +169,19 @@ &gpio2 {
 
 &gpio3 {
 	gpio-line-names =
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
 		"[I2C0_SDA]",
 		"[I2C0_SCL]",
-		"[JTAG]",
-		"[JTAG]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
+		"[JTAG EMU0]",
+		"[JTAG EMU1]",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
 		"P1.03 [USB1]",
 		"P1.36 [PWM0A]",
 		"P1.33 [PRU0.1]",
@@ -191,16 +191,16 @@ &gpio3 {
 		"P2.34 [PRU0.5]",
 		"P2.28 [PRU0.6]",
 		"P1.29 [PRU0.7]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]";
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
 };
 
 &am33xx_pinmux {
Signature · 1 line
2.25.1
#1 lore raw

PATCH 2/2 ARM: dts: am335x-boneblack.dts: unique gpio-line-names

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/

---
 arch/arm/boot/dts/am335x-boneblack.dts | 130 ++++++++++++-------------
 1 file changed, 65 insertions(+), 65 deletions(-)
arch/arm/boot/dts/am335x-boneblack.dts +65 -65
index b4feb85e171a..ad9d32c7ec44 100644
@@ -26,54 +26,54 @@ oppnitro-1000000000 {
 
 &gpio0 {
 	gpio-line-names =
-		"[ethernet]",
-		"[ethernet]",
+		"[mdio_data]",
+		"[mdio_clk]",
 		"P9_22 [spi0_sclk]",
 		"P9_21 [spi0_d0]",
 		"P9_18 [spi0_d1]",
 		"P9_17 [spi0_cs0]",
-		"[sd card]",
+		"[mmc0_cd]",
 		"P8_42A [ecappwm0]",
-		"P8_35 [hdmi]",
-		"P8_33 [hdmi]",
-		"P8_31 [hdmi]",
-		"P8_32 [hdmi]",
+		"P8_35 [lcd d12]",
+		"P8_33 [lcd d13]",
+		"P8_31 [lcd d14]",
+		"P8_32 [lcd d15]",
 		"P9_20 [i2c2_sda]",
 		"P9_19 [i2c2_scl]",
 		"P9_26 [uart1_rxd]",
 		"P9_24 [uart1_txd]",
-		"[ethernet]",
-		"[ethernet]",
-		"[usb]",
-		"[hdmi]",
+		"[rmii1_txd3]",
+		"[rmii1_txd2]",
+		"[usb0_drvvbus]",
+		"[hdmi cec]",
 		"P9_41B",
-		"[ethernet]",
+		"[rmii1_txd1]",
 		"P8_19 [ehrpwm2a]",
 		"P8_13 [ehrpwm2b]",
-		"[NC]",
-		"[NC]",
+		"NC",
+		"NC",
 		"P8_14",
 		"P8_17",
-		"[ethernet]",
-		"[ethernet]",
+		"[rmii1_txd0]",
+		"[rmii1_refclk]",
 		"P9_11 [uart4_rxd]",
 		"P9_13 [uart4_txd]";
 };
 
 &gpio1 {
 	gpio-line-names =
-		"P8_25 [emmc]",
-		"[emmc]",
-		"P8_5 [emmc]",
-		"P8_6 [emmc]",
-		"P8_23 [emmc]",
-		"P8_22 [emmc]",
-		"P8_3 [emmc]",
-		"P8_4 [emmc]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
+		"P8_25 [mmc1_dat0]",
+		"[mmc1_dat1]",
+		"P8_5 [mmc1_dat2]",
+		"P8_6 [mmc1_dat3]",
+		"P8_23 [mmc1_dat4]",
+		"P8_22 [mmc1_dat5]",
+		"P8_3 [mmc1_dat6]",
+		"P8_4 [mmc1_dat7]",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
 		"P8_12",
 		"P8_11",
 		"P8_16",
@@ -82,13 +82,13 @@ &gpio1 {
 		"P9_23",
 		"P9_14 [ehrpwm1a]",
 		"P9_16 [ehrpwm1b]",
-		"[emmc]",
+		"[emmc rst]",
 		"[usr0 led]",
 		"[usr1 led]",
 		"[usr2 led]",
 		"[usr3 led]",
-		"[hdmi]",
-		"[usb]",
+		"[hdmi irq]",
+		"[usb vbus oc]",
 		"[hdmi audio]",
 		"P9_12",
 		"P8_26",
@@ -116,38 +116,38 @@ &gpio2 {
 		"P8_38 [hdmi]",
 		"P8_36 [hdmi]",
 		"P8_34 [hdmi]",
-		"[ethernet]",
-		"[ethernet]",
-		"[ethernet]",
-		"[ethernet]",
+		"[rmii1_rxd3]",
+		"[rmii1_rxd2]",
+		"[rmii1_rxd1]",
+		"[rmii1_rxd0]",
 		"P8_27 [hdmi]",
 		"P8_29 [hdmi]",
 		"P8_28 [hdmi]",
 		"P8_30 [hdmi]",
-		"[emmc]",
-		"[emmc]",
-		"[emmc]",
-		"[emmc]",
-		"[emmc]",
-		"[emmc]";
+		"[mmc0_dat3]",
+		"[mmc0_dat2]",
+		"[mmc0_dat1]",
+		"[mmc0_dat0]",
+		"[mmc0_clk]",
+		"[mmc0_cmd]";
 };
 
 &gpio3 {
 	gpio-line-names =
-		"[ethernet]",
-		"[ethernet]",
-		"[ethernet]",
-		"[ethernet]",
-		"[ethernet]",
-		"[i2c0]",
-		"[i2c0]",
-		"[emu]",
-		"[emu]",
-		"[ethernet]",
-		"[ethernet]",
-		"[NC]",
-		"[NC]",
-		"[usb]",
+		"[mii col]",
+		"[mii crs]",
+		"[mii rx err]",
+		"[mii tx en]",
+		"[mii rx dv]",
+		"[i2c0 sda]",
+		"[i2c0 scl]",
+		"[jtag emu0]",
+		"[jtag emu1]",
+		"[mii tx clk]",
+		"[mii rx clk]",
+		"NC",
+		"NC",
+		"[usb vbus en]",
 		"P9_31 [spi1_sclk]",
 		"P9_29 [spi1_d0]",
 		"P9_30 [spi1_d1]",
@@ -156,14 +156,14 @@ &gpio3 {
 		"P9_27",
 		"P9_41A",
 		"P9_25",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]",
-		"[NC]";
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
 };
Signature · 1 line
2.25.1
Reviewed-by on v1 2/2
#2 lore raw

Re: [PATCH 2/2] ARM: dts: am335x-boneblack.dts: unique gpio-line-names

Quoted 9 lines · Drew Fustini

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/

Yours,
Linus Walleij

Reviewed-by on v1 2/2
#3 lore raw

Re: [PATCH 2/2] ARM: dts: am335x-boneblack.dts: unique gpio-line-names

In reply to Drew Fustini
Quoted 11 lines · Drew Fustini

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/

---

Reviewed-by on v1 1/2
#4 lore raw
In reply to Drew Fustini
Quoted 9 lines · Drew Fustini

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/

This certainly looks better!

Yours,
Linus Walleij

Reviewed-by on v1 1/2
#5 lore raw
In reply to Drew Fustini
Quoted 11 lines · Drew Fustini

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/

---

#6 lore raw
In reply to Drew Fustini
Quoted 7 lines · Drew Fustini

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/

So are these needed for v5.12 as fixes, or can these wait until after the merge window for v5.13?

Regards,

Tony

#7 lore raw
Quoted 7 lines · Tony Lindgren
Quoted 6 lines · Drew Fustini

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

Quoted 8 lines
Quoted 1 line

[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/

So are these needed for v5.12 as fixes, or can these wait until after the merge window for v5.13?

Regards,

Tony

I suppose it depends on if/when the patches to make gpio lines unique go in. I believe the last response from Linus W. was in mid-December and indicated he holding off merging as it was immature [1]

Thanks,
Drew

[1] https://lore.kernel.org/linux-gpio/CACRpkdbXRHCDGX-YBbNY7cMob0dZNhi1ETA3QnC71ZtOYB30JQ@mail.gmail.com/

#8 lore raw
Quoted 13 lines · Drew Fustini
Quoted 12 lines · Tony Lindgren
Quoted 7 lines · Drew Fustini

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/

So are these needed for v5.12 as fixes, or can these wait until after the merge window for v5.13?

Quoted 7 lines
Quoted 3 lines

Regards,

Tony

I suppose it depends on if/when the patches to make gpio lines unique go in. I believe the last response from Linus W. was in mid-December and indicated he holding off merging as it was immature [1]

There is no hurry with that plus I hold that patch back indefinately as it seems. I want to make line names unique for devices not probing from DT but DT devices, I dunno.

Yours,
Linus Walleij

#9 lore raw
In reply to Drew Fustini

Hi,

Quoted 5 lines · Drew Fustini

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

Applying this one into omap-for-v5.13/dt thanks. However the second patch does not apply against v5.12-rc2, Drew can you please repost the second patch?

Regards,

Tony

#10 lore raw
Quoted 9 lines · Tony Lindgren

Hi,

Quoted 5 lines · Drew Fustini

Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected".

Quoted 7 lines

Applying this one into omap-for-v5.13/dt thanks. However the second patch does not apply against v5.12-rc2, Drew can you please repost the second patch?

Regards,

Tony

Hi Tony, I have posted a new patch that applies okay to mainline.

Thanks,
Drew

[1] https://lore.kernel.org/linux-gpio/[email protected]/T/#u