dt-bindings: mtd: move partition binding to its own file
Subsystems (2)
PATCH v3 1/3 dt-bindings: mtd: move partition binding to its own file
From: Rafał Miłecki <[email protected]>
Single partition binding is quite common and may be:
1. Used by multiple parsers
2. Extended for more specific cases
Move it to separated file to avoid code duplication.
--- .../mtd/partitions/fixed-partitions.yaml | 33 +------------ .../bindings/mtd/partitions/partition.yaml | 47 +++++++++++++++++++ 2 files changed, 48 insertions(+), 32 deletions(-) create mode 100644 Documentation/devicetree/bindings/mtd/partitions/partition.yaml
Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml +1 -32
@@ -27,38 +27,7 @@ properties: patternProperties: "@[0-9a-f]+$": - description: node describing a single flash partition - type: object - - properties: - reg: - description: partition's offset and size within the flash - maxItems: 1 - - label: - description: The label / name for this partition. If omitted, the label - is taken from the node name (excluding the unit address). - - read-only: - description: This parameter, if present, is a hint that this partition - should only be mounted read-only. This is usually used for flash - partitions containing early-boot firmware images or data which should - not be clobbered. - type: boolean - - lock: - description: Do not unlock the partition at initialization time (not - supported on all devices) - type: boolean - - slc-mode: - description: This parameter, if present, allows one to emulate SLC mode - on a partition attached to an MLC NAND thus making this partition - immune to paired-pages corruptions - type: boolean - - required: - - reg + $ref: "partition.yaml#" required: - "#address-cells"
Documentation/devicetree/bindings/mtd/partitions/partition.yaml new file +47 -0
47 lines not on this page · raw message
Signature · 6 lines
2.26.2 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v3 2/3 dt-bindings: mtd: add binding for BCM4908 partitions
From: Rafał Miłecki <[email protected]>
BCM4908 uses fixed partitions layout but function of some partitions may vary. Some devices use multiple firmware partitions and those partitions should be marked to let system discover their purpose.
---
V2: Use enum: [ 1, 2 ] for address & size
Use ^partition@[0-9a-f]+$ pattern ("partition" was added) Drop unneeded allOf
Add unevaluatedProperties
--- .../partitions/brcm,bcm4908-partitions.yaml | 70 +++++++++++++++++++ 1 file changed, 70 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/partitions/brcm,bcm4908-partitions.yaml
Documentation/devicetree/bindings/mtd/partitions/brcm,bcm4908-partitions.yaml new file +70 -0
@@ -0,0 +1,70 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/brcm,bcm4908-partitions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM4908 partitioning + +description: | + Broadcom BCM4908 CFE bootloader supports two firmware partitions. One is used + for regular booting, the other is treated as fallback. + + This binding allows defining all fixed partitions and marking those containing + firmware. System can use that information e.g. for booting or flashing + purposes. + +maintainers: + - Rafał Miłecki <[email protected]> + +properties: + compatible: + const: brcm,bcm4908-partitions + + "#address-cells": + enum: [ 1, 2 ] + + "#size-cells": + enum: [ 1, 2 ] + +patternProperties: + "^partition@[0-9a-f]+$": + $ref: "partition.yaml#" + properties: + compatible: + const: brcm,bcm4908-firmware + unevaluatedProperties: false + +required: + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + partitions { + compatible = "brcm,bcm4908-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "cferom"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + compatible = "brcm,bcm4908-firmware"; + reg = <0x100000 0xf00000>; + }; + + partition@1000000 { + compatible = "brcm,bcm4908-firmware"; + reg = <0x1000000 0xf00000>; + }; + + partition@1f00000 { + label = "calibration"; + reg = <0x1f00000 0x100000>; + }; + };
Signature · 6 lines
2.26.2 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v3 3/3 mtd: parsers: ofpart: support BCM4908 fixed partitions
In reply to Rafał MiłeckiFrom: Rafał Miłecki <[email protected]>
BCM4908 partitioning is based on fixed layout but allows specifying multiple firmware partitions. It requires detecting which firmware partition was used for booting current kernel.
To support such cases without duplicating a lot of code (without copying most of the ofpart.c code) support for post-parsing callback was added.
BCM4908 callback simply reads offset of currently used firmware partition from the DT. Bootloader specifies it using the "brcm_blparms" property.
---
V3: Add #include "bcm4908-partitions.h" to fix:drivers/mtd/parsers/bcm4908-partitions.c:45:5: warning: no previous prototype for function 'bcm4908_partitions_post_parse' [-Wmissing-prototypes]
--- drivers/mtd/parsers/Makefile | 1 + drivers/mtd/parsers/bcm4908-partitions.c | 64 ++++++++++++++++++++++++ drivers/mtd/parsers/bcm4908-partitions.h | 7 +++ drivers/mtd/parsers/ofpart.c | 28 ++++++++++- 4 files changed, 98 insertions(+), 2 deletions(-) create mode 100644 drivers/mtd/parsers/bcm4908-partitions.c create mode 100644 drivers/mtd/parsers/bcm4908-partitions.h
drivers/mtd/parsers/Makefile +1 -0
@@ -4,6 +4,7 @@ obj-$(CONFIG_MTD_BCM47XX_PARTS) += bcm47xxpart.o obj-$(CONFIG_MTD_BCM63XX_PARTS) += bcm63xxpart.o obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o obj-$(CONFIG_MTD_OF_PARTS) += ofpart.o +obj-$(CONFIG_MTD_OF_PARTS) += bcm4908-partitions.o obj-$(CONFIG_MTD_PARSER_IMAGETAG) += parser_imagetag.o obj-$(CONFIG_MTD_AFS_PARTS) += afs.o obj-$(CONFIG_MTD_PARSER_TRX) += parser_trx.o
drivers/mtd/parsers/bcm4908-partitions.c new file +64 -0
64 lines not on this page · raw message
drivers/mtd/parsers/bcm4908-partitions.h new file +7 -0
@@ -0,0 +1,7 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __BCM4908_PARTITIONS_H +#define __BCM4908_PARTITIONS_H + +int bcm4908_partitions_post_parse (struct mtd_info *mtd,struct mtd_partition *parts,int nr_parts); + +#endif
drivers/mtd/parsers/ofpart.c +26 -2
@@ -16,6 +16,18 @@#include <linux/slab.h> #include <linux/mtd/partitions.h> +#include "bcm4908-partitions.h" + +struct fixed_partitions_quirks { +int (*post_parse)(struct mtd_info *mtd,struct mtd_partition *parts,int nr_parts); +}; + +struct fixed_partitions_quirks bcm4908_partitions_quirks = { + .post_parse = bcm4908_partitions_post_parse, +}; + +static const struct of_device_id parse_ofpart_match_table[]; +static bool node_has_compatible (struct device_node *pp) {return of_get_property (pp,"compatible" ,NULL );
@@ -25,6 +37,8 @@ static int parse_fixed_partitions(struct mtd_info *master,const struct mtd_partition **pparts, struct mtd_part_parser_data *data) { + const struct fixed_partitions_quirks *quirks; +const struct of_device_id *of_id;struct mtd_partition *parts;struct device_node *mtd_node;struct device_node *ofpart_node;
@@ -33,7 +47,6 @@ static int parse_fixed_partitions(struct mtd_info *master,int nr_parts, i, ret =0 ;bool dedicated = true; -/* Pull of_node from the master device node */ mtd_node =mtd_get_of_node (master);if (!mtd_node)
@@ -50,11 +63,16 @@ static int parse_fixed_partitions(struct mtd_info *master, master->name, mtd_node); ofpart_node = mtd_node; dedicated = false; - }else if (!of_device_is_compatible (ofpart_node,"fixed-partitions" )) { + } + + of_id =of_match_node (parse_ofpart_match_table, ofpart_node); +if (dedicated && !of_id) {/* The 'partitions' subnode might be used by another parser */ return 0 ; } + quirks = of_id ? of_id->data :NULL ; +/* First count the subnodes */ nr_parts =0 ;for_each_child_of_node (ofpart_node, pp) {
@@ -126,6 +144,9 @@ static int parse_fixed_partitions(struct mtd_info *master,if (!nr_parts) goto ofpart_none; +if (quirks && quirks->post_parse) + quirks->post_parse (master, parts, nr_parts); + *pparts = parts;return nr_parts;
@@ -140,7 +161,10 @@ static int parse_fixed_partitions(struct mtd_info *master, }static const struct of_device_id parse_ofpart_match_table[] = { +/* Generic */ { .compatible ="fixed-partitions" }, +/* Customized */ + { .compatible ="brcm,bcm4908-partitions" , .data = &bcm4908_partitions_quirks, }, {}, };MODULE_DEVICE_TABLE (of, parse_ofpart_match_table);
Signature · 6 lines
2.26.2 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/