Add MIPI rx DPI support

index 65cc059..04536cc 100644
@@ -189,10 +189,10 @@ static int wait_aux_op_finish(struct anx7625_data *ctx)
 			       AP_AUX_CTRL_STATUS);
 	if (val < 0 || (val & 0x0F)) {
 		DRM_DEV_ERROR(dev, "aux status %02x\n", val);
-		val = -EIO;
+		return -EIO;
 	}
 
-	return val;
+	return 0;
 }
 
 static int anx7625_video_mute_control(struct anx7625_data *ctx,

index 04536cc..5c9b801 100644
@@ -150,18 +150,18 @@ static int anx7625_write_and(struct anx7625_data *ctx,
 	return anx7625_reg_write(ctx, client, offset, (val & (mask)));
 }
 
-static int anx7625_write_and_or(struct anx7625_data *ctx,
-				struct i2c_client *client,
-				u8 offset, u8 and_mask, u8 or_mask)
+static int anx7625_config_bit_matrix(struct anx7625_data *ctx)
 {
-	int val;
+	int i, ret;
 
-	val = anx7625_reg_read(ctx, client, offset);
-	if (val < 0)
-		return val;
+	ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
+			       AUDIO_CONTROL_REGISTER, 0x80);
+	for (i = 0; i < 13; i++)
+		ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+					 VIDEO_BIT_MATRIX_12 + i,
+					 0x18 + i);
 
-	return anx7625_reg_write(ctx, client,
-				 offset, (val & and_mask) | (or_mask));
+	return ret;
 }
 
 static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx)

@@ -219,38 +219,6 @@ static int anx7625_video_mute_control(struct anx7625_data *ctx,
 	return ret;
 }
 
-static int anx7625_config_audio_input(struct anx7625_data *ctx)
-{
-	struct device *dev = &ctx->client->dev;
-	int ret;
-
-	/* Channel num */
-	ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
-				AUDIO_CHANNEL_STATUS_6, I2S_CH_2 << 5);
-
-	/* FS */
-	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
-				    AUDIO_CHANNEL_STATUS_4,
-				    0xf0, AUDIO_FS_48K);
-	/* Word length */
-	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
-				    AUDIO_CHANNEL_STATUS_5,
-				    0xf0, AUDIO_W_LEN_24_24MAX);
-	/* I2S */
-	ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
-				AUDIO_CHANNEL_STATUS_6, I2S_SLAVE_MODE);
-	ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client,
-				 AUDIO_CONTROL_REGISTER, ~TDM_TIMING_MODE);
-	/* Audio change flag */
-	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
-				AP_AV_STATUS, AP_AUDIO_CHG);
-
-	if (ret < 0)
-		DRM_DEV_ERROR(dev, "fail to config audio.\n");
-
-	return ret;
-}
-
 /* Reduction of fraction a/b */
 static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b)
 {

@@ -410,7 +378,7 @@ static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx)
 	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
 			MIPI_LANE_CTRL_0, 0xfc);
 	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client,
-				MIPI_LANE_CTRL_0, 3);
+				MIPI_LANE_CTRL_0, ctx->pdata.mipi_lanes - 1);
 
 	/* Htotal */
 	htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min +

@@ -595,6 +563,76 @@ static int anx7625_dsi_config(struct anx7625_data *ctx)
 	return ret;
 }
 
+static int anx7625_api_dpi_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	u16 freq = ctx->dt.pixelclock.min / 1000;
+	int ret;
+
+	/* configure pixel clock */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				PIXEL_CLOCK_L, freq & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 PIXEL_CLOCK_H, (freq >> 8));
+
+	/* set DPI mode */
+	/* set to DPI PLL module sel */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_9, 0x20);
+	/* power down MIPI */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_LANE_CTRL_10, 0x08);
+	/* enable DPI mode */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_18, 0x1C);
+	/* set first edge */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+				 VIDEO_CONTROL_0, 0x06);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n");
+
+	return ret;
+}
+
+static int anx7625_dpi_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n");
+
+	/* DSC disable */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				R_DSC_CTRL_0, ~DSC_EN);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n");
+		return ret;
+	}
+
+	ret = anx7625_config_bit_matrix(ctx);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "config bit matrix failed.\n");
+		return ret;
+	}
+
+	ret = anx7625_api_dpi_config(ctx);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n");
+		return ret;
+	}
+
+	/* set MIPI RX EN */
+	ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+			       AP_AV_STATUS, AP_MIPI_RX_EN);
+	/* clear mute flag */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				 AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n");
+
+	return ret;
+}
+
 static void anx7625_dp_start(struct anx7625_data *ctx)
 {
 	int ret;

@@ -605,9 +643,10 @@ static void anx7625_dp_start(struct anx7625_data *ctx)
 		return;
 	}
 
-	anx7625_config_audio_input(ctx);
-
-	ret = anx7625_dsi_config(ctx);
+	if (ctx->pdata.is_dpi)
+		ret = anx7625_dpi_config(ctx);
+	else
+		ret = anx7625_dsi_config(ctx);
 
 	if (ret < 0)
 		DRM_DEV_ERROR(dev, "MIPI phy setup error.\n");

@@ -1051,6 +1090,7 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
 		return;
 	}
 
+	ctx->hpd_status = 1;
 	ctx->hpd_high_cnt++;
 
 	/* Not support HDCP */

@@ -1060,8 +1100,10 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
 	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10);
 	/* Interrupt for DRM */
 	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01);
-	if (ret < 0)
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n");
 		return;
+	}
 
 	ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86);
 	if (ret < 0)

@@ -1080,6 +1122,10 @@ static void anx7625_hpd_polling(struct anx7625_data *ctx)
 	int ret, val;
 	struct device *dev = &ctx->client->dev;
 
+	/* Interrupt mode, no need poll HPD status, just return */
+	if (ctx->pdata.intp_irq)
+		return;
+
 	if (atomic_read(&ctx->power_status) != 1) {
 		DRM_DEV_DEBUG_DRIVER(dev, "No need to poling HPD status.\n");
 		return;

@@ -1130,6 +1176,21 @@ static void anx7625_remove_edid(struct anx7625_data *ctx)
 	ctx->slimport_edid_p.edid_block_num = -1;
 }
 
+static void anx7625_dp_adjust_swing(struct anx7625_data *ctx)
+{
+	int i;
+
+	for (i = 0; i < ctx->pdata.dp_lane0_swing_reg_cnt; i++)
+		anx7625_reg_write(ctx, ctx->i2c.tx_p1_client,
+				  DP_TX_LANE0_SWING_REG0 + i,
+				  ctx->pdata.lane0_reg_data[i] & 0xFF);
+
+	for (i = 0; i < ctx->pdata.dp_lane1_swing_reg_cnt; i++)
+		anx7625_reg_write(ctx, ctx->i2c.tx_p1_client,
+				  DP_TX_LANE1_SWING_REG0 + i,
+				  ctx->pdata.lane1_reg_data[i] & 0xFF);
+}
+
 static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
 {
 	struct device *dev = &ctx->client->dev;

@@ -1145,9 +1206,8 @@ static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
 	} else {
 		DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n");
 		anx7625_start_dp_work(ctx);
+		anx7625_dp_adjust_swing(ctx);
 	}
-
-	ctx->hpd_status = 1;
 }
 
 static int anx7625_hpd_change_detect(struct anx7625_data *ctx)

@@ -1224,20 +1284,70 @@ static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
+static int anx7625_get_swing_setting(struct device *dev,
+				     struct anx7625_platform_data *pdata)
+{
+	int num_regs;
+
+	if (of_get_property(dev->of_node,
+			    "analogix,lane0-swing", &num_regs)) {
+		if (num_regs > DP_TX_SWING_REG_CNT)
+			num_regs = DP_TX_SWING_REG_CNT;
+
+		pdata->dp_lane0_swing_reg_cnt = num_regs;
+		of_property_read_u32_array(dev->of_node, "analogix,lane0-swing",
+					   pdata->lane0_reg_data, num_regs);
+	}
+
+	if (of_get_property(dev->of_node,
+			    "analogix,lane1-swing", &num_regs)) {
+		if (num_regs > DP_TX_SWING_REG_CNT)
+			num_regs = DP_TX_SWING_REG_CNT;
+
+		pdata->dp_lane1_swing_reg_cnt = num_regs;
+		of_property_read_u32_array(dev->of_node, "analogix,lane1-swing",
+					   pdata->lane1_reg_data, num_regs);
+	}
+
+	return 0;
+}
+
 static int anx7625_parse_dt(struct device *dev,
 			    struct anx7625_platform_data *pdata)
 {
-	struct device_node *np = dev->of_node;
+	struct device_node *np = dev->of_node, *ep0;
 	struct drm_panel *panel;
 	int ret;
+	int bus_type, mipi_lanes;
 
+	anx7625_get_swing_setting(dev, pdata);
+
+	pdata->is_dpi = 1; /* default dpi mode */
 	pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0);
 	if (!pdata->mipi_host_node) {
 		DRM_DEV_ERROR(dev, "fail to get internal panel.\n");
 		return -ENODEV;
 	}
 
-	DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n");
+	ep0 = of_graph_get_endpoint_by_regs(np, 0, 0);
+	if (ep0) {
+		if (of_property_read_u32(ep0, "bus-type", &bus_type))
+			bus_type = 0;
+
+		mipi_lanes = of_property_count_u32_elems(ep0, "data-lanes");
+	}
+
+	if (bus_type == 5) /* bus type is Parallel(DSI) */
+		pdata->is_dpi = 0;
+
+	pdata->mipi_lanes = mipi_lanes;
+	if (pdata->mipi_lanes > MAX_LANES_SUPPORT || pdata->mipi_lanes <= 0)
+		pdata->mipi_lanes = MAX_LANES_SUPPORT;
+
+	if (pdata->is_dpi)
+		DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DPI host node.\n");
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n");
 
 	ret = drm_of_find_panel_or_bridge(np, 1, 0, &panel, NULL);
 	if (ret < 0) {

@@ -1300,9 +1410,13 @@ static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx)
 {
 	struct device *dev = &ctx->client->dev;
 
-	DRM_DEV_DEBUG_DRIVER(dev, "sink detect, return connected\n");
+	DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n");
+
+	if (ctx->pdata.panel_bridge)
+		return connector_status_connected;
 
-	return connector_status_connected;
+	return ctx->hpd_status ? connector_status_connected :
+				     connector_status_disconnected;
 }
 
 static int anx7625_attach_dsi(struct anx7625_data *ctx)

@@ -1330,7 +1444,7 @@ static int anx7625_attach_dsi(struct anx7625_data *ctx)
 		return -EINVAL;
 	}
 
-	dsi->lanes = 4;
+	dsi->lanes = ctx->pdata.mipi_lanes;
 	dsi->format = MIPI_DSI_FMT_RGB888;
 	dsi->mode_flags = MIPI_DSI_MODE_VIDEO	|
 		MIPI_DSI_MODE_VIDEO_SYNC_PULSE	|

@@ -1376,10 +1490,12 @@ static int anx7625_bridge_attach(struct drm_bridge *bridge,
 		return -ENODEV;
 	}
 
-	err = anx7625_attach_dsi(ctx);
-	if (err) {
-		DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err);
-		return err;
+	if (!ctx->pdata.is_dpi) {
+		err = anx7625_attach_dsi(ctx);
+		if (err) {
+			DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err);
+			return err;
+		}
 	}
 
 	if (ctx->pdata.panel_bridge) {

@@ -1478,6 +1594,10 @@ static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge,
 
 	DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n");
 
+	/* No need fixup for external monitor */
+	if (!ctx->pdata.panel_bridge)
+		return true;
+
 	hsync = mode->hsync_end - mode->hsync_start;
 	hfp = mode->hsync_start - mode->hdisplay;
 	hbp = mode->htotal - mode->hsync_end;

@@ -1786,8 +1906,13 @@ static int anx7625_i2c_probe(struct i2c_client *client,
 
 	platform->bridge.funcs = &anx7625_bridge_funcs;
 	platform->bridge.of_node = client->dev.of_node;
-	platform->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_HPD;
-	platform->bridge.type = DRM_MODE_CONNECTOR_eDP;
+	platform->bridge.ops = DRM_BRIDGE_OP_EDID;
+	if (!platform->pdata.panel_bridge)
+		platform->bridge.ops |= DRM_BRIDGE_OP_HPD |
+					DRM_BRIDGE_OP_DETECT;
+	platform->bridge.type = platform->pdata.panel_bridge ?
+				    DRM_MODE_CONNECTOR_eDP :
+				    DRM_MODE_CONNECTOR_DisplayPort;
 	drm_bridge_add(&platform->bridge);
 
 	DRM_DEV_DEBUG_DRIVER(dev, "probe done\n");

index 193ad86..beee95d 100644
@@ -141,12 +141,20 @@
 #define  HORIZONTAL_BACK_PORCH_H      0x22  /* Bit[7:4] are reserved */
 
 /******** END of I2C Address 0x72 *********/
+
+/***************************************************************/
+/* Register definition of device address 0x7a */
+#define DP_TX_SWING_REG_CNT		0x14
+#define DP_TX_LANE0_SWING_REG0		0x00
+#define DP_TX_LANE1_SWING_REG0		0x14
+/******** END of I2C Address 0x7a *********/
+
 /***************************************************************/
 /* Register definition of device address 0x7e */
 
 #define  I2C_ADDR_7E_FLASH_CONTROLLER  0x7E
 
-#define FLASH_LOAD_STA 0x05
+#define FLASH_LOAD_STA          0x05
 #define FLASH_LOAD_STA_CHK	BIT(7)
 
 #define  XTAL_FRQ_SEL    0x3F

@@ -347,11 +355,19 @@ struct s_edid_data {
 
 /***************** Display End *****************/
 
+#define MAX_LANES_SUPPORT	4
+
 struct anx7625_platform_data {
 	struct gpio_desc *gpio_p_on;
 	struct gpio_desc *gpio_reset;
 	struct drm_bridge *panel_bridge;
 	int intp_irq;
+	int is_dpi;
+	int mipi_lanes;
+	int dp_lane0_swing_reg_cnt;
+	int lane0_reg_data[DP_TX_SWING_REG_CNT];
+	int dp_lane1_swing_reg_cnt;
+	int lane1_reg_data[DP_TX_SWING_REG_CNT];
 	u32 low_power_mode;
 	struct device_node *mipi_host_node;
 };

index 5c9b801..5e19170 100644
@@ -633,6 +633,150 @@ static int anx7625_dpi_config(struct anx7625_data *ctx)
 	return ret;
 }
 
+static int anx7625_aux_dpcd_read(struct anx7625_data *ctx,
+				 u8 addrh, u8 addrm, u8 addrl,
+				 u8 len, u8 *buf)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+	u8 cmd;
+
+	if (len > MAX_DPCD_BUFFER_SIZE) {
+		DRM_DEV_ERROR(dev, "exceed aux buffer len.\n");
+		return -E2BIG;
+	}
+
+	cmd = ((len - 1) << 4) | 0x09;
+
+	/* Set command and length */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_COMMAND, cmd);
+
+	/* Set aux access address */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_7_0, addrl);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_15_8, addrm);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_19_16, addrh);
+
+	/* Enable aux access */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN);
+
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "cannot access aux related register.\n");
+		return -EIO;
+	}
+
+	usleep_range(2000, 2100);
+
+	ret = wait_aux_op_finish(ctx);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "aux IO error: wait aux op finish.\n");
+		return ret;
+	}
+
+	ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+				     AP_AUX_BUFF_START, len, buf);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "read dpcd register failed\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int anx7625_read_flash_status(struct anx7625_data *ctx)
+{
+	return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, R_RAM_CTRL);
+}
+
+static int anx7625_hdcp_key_probe(struct anx7625_data *ctx)
+{
+	int ret, val;
+	struct device *dev = &ctx->client->dev;
+	u8 ident[32];
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				FLASH_ADDR_HIGH, 0x91);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 FLASH_ADDR_LOW, 0xA0);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "IO error : set key flash address.\n");
+		return ret;
+	}
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				FLASH_LEN_HIGH, (FLASH_BUF_LEN - 1) >> 8);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 FLASH_LEN_LOW, (FLASH_BUF_LEN - 1) & 0xFF);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "IO error : set key flash len.\n");
+		return ret;
+	}
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				R_FLASH_RW_CTRL, FLASH_READ);
+	ret |= readx_poll_timeout(anx7625_read_flash_status,
+				  ctx, val,
+				  ((val & FLASH_DONE) || (val < 0)),
+				  2000,
+				  2000 * 150);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "flash read access fail!\n");
+		return -EIO;
+	}
+
+	ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+				     FLASH_BUF_BASE_ADDR,
+				     FLASH_BUF_LEN, ident);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "read flash data fail!\n");
+		return -EIO;
+	}
+
+	if (ident[29] == 0xFF && ident[30] == 0xFF && ident[31] == 0xFF)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int anx7625_hdcp_setting(struct anx7625_data *ctx)
+{
+	u8 bcap;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	ret = anx7625_hdcp_key_probe(ctx);
+	if (ret) {
+		DRM_DEV_DEBUG_DRIVER(dev, "disable HDCP by config\n");
+		return anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+					 0xee, 0x9f);
+	}
+
+	anx7625_aux_dpcd_read(ctx, 0x06, 0x80, 0x28, 1, &bcap);
+	if (!(bcap & 0x01)) {
+		DRM_DEV_DEBUG_DRIVER(dev, "bcap(0x%x) not support HDCP 1.4.\n",
+				     bcap);
+		return anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+					 0xee, 0x9f);
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "enable HDCP 1.4\n");
+
+	ret = anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xee, 0x20);
+
+	/* Try auth flag */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10);
+	/* Interrupt for DRM */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "fail to enable HDCP\n");
+
+	return ret;
+}
+
 static void anx7625_dp_start(struct anx7625_data *ctx)
 {
 	int ret;

@@ -643,6 +787,9 @@ static void anx7625_dp_start(struct anx7625_data *ctx)
 		return;
 	}
 
+	/* HDCP config */
+	anx7625_hdcp_setting(ctx);
+
 	if (ctx->pdata.is_dpi)
 		ret = anx7625_dpi_config(ctx);
 	else

index beee95d..c6f93e4 100644
@@ -154,9 +154,45 @@
 
 #define  I2C_ADDR_7E_FLASH_CONTROLLER  0x7E
 
+#define FLASH_SRAM_SEL          0x00
+#define SRAM_ADDR_HIGH          0x01
+#define SRAM_ADDR_LOW           0x02
+#define SRAM_LEN_HIGH           0x03
+#define SRAM_LEN_LOW            0x04
 #define FLASH_LOAD_STA          0x05
 #define FLASH_LOAD_STA_CHK	BIT(7)
 
+#define R_RAM_CTRL              0x05
+/* bit positions */
+#define FLASH_DONE              BIT(7)
+#define BOOT_LOAD_DONE          BIT(6)
+#define CRC_OK                  BIT(5)
+#define LOAD_DONE               BIT(4)
+#define O_RW_DONE               BIT(3)
+#define FUSE_BUSY               BIT(2)
+#define DECRYPT_EN              BIT(1)
+#define LOAD_START              BIT(0)
+
+#define FLASH_ADDR_HIGH         0x0F
+#define FLASH_ADDR_LOW          0x10
+#define FLASH_LEN_HIGH          0x31
+#define FLASH_LEN_LOW           0x32
+
+#define R_FLASH_RW_CTRL         0x33
+/* bit positions */
+#define READ_DELAY_SELECT       BIT(7)
+#define GENERAL_INSTRUCTION_EN  BIT(6)
+#define FLASH_ERASE_EN          BIT(5)
+#define RDID_READ_EN            BIT(4)
+#define REMS_READ_EN            BIT(3)
+#define WRITE_STATUS_EN         BIT(2)
+#define FLASH_READ              BIT(1)
+#define FLASH_WRITE             BIT(0)
+
+#define FLASH_BUF_BASE_ADDR     0x60
+#define FLASH_BUF_LEN           0x20
+#define FLASH_KEY_OFFSET        0x8000
+
 #define  XTAL_FRQ_SEL    0x3F
 /* bit field positions */
 #define  XTAL_FRQ_SEL_POS    5

index 5e19170..f4653f2 100644
@@ -30,6 +30,8 @@
 #include <drm/drm_print.h>
 #include <drm/drm_probe_helper.h>
 
+#include <sound/hdmi-codec.h>
+
 #include <video/display_timing.h>
 
 #include "anx7625.h"

@@ -150,6 +152,20 @@ static int anx7625_write_and(struct anx7625_data *ctx,
 	return anx7625_reg_write(ctx, client, offset, (val & (mask)));
 }
 
+static int anx7625_write_and_or(struct anx7625_data *ctx,
+				struct i2c_client *client,
+				u8 offset, u8 and_mask, u8 or_mask)
+{
+	int val;
+
+	val = anx7625_reg_read(ctx, client, offset);
+	if (val < 0)
+		return val;
+
+	return anx7625_reg_write(ctx, client,
+				 offset, (val & and_mask) | (or_mask));
+}
+
 static int anx7625_config_bit_matrix(struct anx7625_data *ctx)
 {
 	int i, ret;

@@ -1496,6 +1512,9 @@ static int anx7625_parse_dt(struct device *dev,
 	else
 		DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n");
 
+	if (of_property_read_bool(np, "analogix,audio-enable"))
+		pdata->audio_en = 1;
+
 	ret = drm_of_find_panel_or_bridge(np, 1, 0, &panel, NULL);
 	if (ret < 0) {
 		if (ret == -ENODEV)

@@ -1566,6 +1585,208 @@ static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx)
 				     connector_status_disconnected;
 }
 
+int anx7625_audio_hw_params(struct device *dev, void *data,
+			    struct hdmi_codec_daifmt *fmt,
+			    struct hdmi_codec_params *params)
+{
+	struct anx7625_data *ctx = dev_get_drvdata(dev);
+	int wl, ch, rate;
+	int ret = 0;
+
+	if (fmt->fmt != HDMI_DSP_A) {
+		DRM_DEV_ERROR(dev, "only supports DSP_A\n");
+		return -EINVAL;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "setting %d Hz, %d bit, %d channels\n",
+			     params->sample_rate, params->sample_width,
+			     params->cea.channels);
+
+	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+				    AUDIO_CHANNEL_STATUS_6,
+				    ~I2S_SLAVE_MODE,
+				    TDM_SLAVE_MODE);
+
+	/* Word length */
+	switch (params->sample_width) {
+	case 16:
+		wl = AUDIO_W_LEN_16_20MAX;
+		break;
+	case 18:
+		wl = AUDIO_W_LEN_18_20MAX;
+		break;
+	case 20:
+		wl = AUDIO_W_LEN_20_20MAX;
+		break;
+	case 24:
+		wl = AUDIO_W_LEN_24_24MAX;
+		break;
+	default:
+		DRM_DEV_DEBUG_DRIVER(dev, "wordlength: %d bit not support",
+				     params->sample_width);
+		return -EINVAL;
+	}
+	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+				    AUDIO_CHANNEL_STATUS_5,
+				    0xf0, wl);
+
+	/* Channel num */
+	switch (params->cea.channels) {
+	case 2:
+		ch = I2S_CH_2;
+		break;
+	case 4:
+		ch = TDM_CH_4;
+		break;
+	case 6:
+		ch = TDM_CH_6;
+		break;
+	case 8:
+		ch = TDM_CH_8;
+		break;
+	default:
+		DRM_DEV_DEBUG_DRIVER(dev, "channel number: %d not support",
+				     params->cea.channels);
+		return -EINVAL;
+	}
+	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+			       AUDIO_CHANNEL_STATUS_6, 0x1f, ch << 5);
+	if (ch > I2S_CH_2)
+		ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
+				AUDIO_CHANNEL_STATUS_6, AUDIO_LAYOUT);
+	else
+		ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client,
+				AUDIO_CHANNEL_STATUS_6, ~AUDIO_LAYOUT);
+
+	/* FS */
+	switch (params->sample_rate) {
+	case 32000:
+		rate = AUDIO_FS_32K;
+		break;
+	case 44100:
+		rate = AUDIO_FS_441K;
+		break;
+	case 48000:
+		rate = AUDIO_FS_48K;
+		break;
+	case 88200:
+		rate = AUDIO_FS_882K;
+		break;
+	case 96000:
+		rate = AUDIO_FS_96K;
+		break;
+	case 176400:
+		rate = AUDIO_FS_1764K;
+		break;
+	case 192000:
+		rate = AUDIO_FS_192K;
+		break;
+	default:
+		DRM_DEV_DEBUG_DRIVER(dev, "sample rate: %d not support",
+				     params->sample_rate);
+		return -EINVAL;
+	}
+	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+				    AUDIO_CHANNEL_STATUS_4,
+				    0xf0, rate);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				AP_AV_STATUS, AP_AUDIO_CHG);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "IO error : config audio.\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static void anx7625_audio_shutdown(struct device *dev, void *data)
+{
+	DRM_DEV_DEBUG_DRIVER(dev, "stop audio\n");
+}
+
+static int anx7625_hdmi_i2s_get_dai_id(struct snd_soc_component *component,
+				       struct device_node *endpoint)
+{
+	struct of_endpoint of_ep;
+	int ret;
+
+	ret = of_graph_parse_endpoint(endpoint, &of_ep);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * HDMI sound should be located at external DPI port
+	 * Didn't have good way to check where is internal(DSI)
+	 * or external(DPI) bridge
+	 */
+	return 0;
+}
+
+static void
+anx7625_audio_update_connector_status(struct anx7625_data *ctx,
+				      enum drm_connector_status status)
+{
+	if (ctx->plugged_cb && ctx->codec_dev) {
+		ctx->plugged_cb(ctx->codec_dev,
+				status == connector_status_connected);
+	}
+}
+
+static int anx7625_audio_hook_plugged_cb(struct device *dev, void *data,
+					 hdmi_codec_plugged_cb fn,
+					 struct device *codec_dev)
+{
+	struct anx7625_data *ctx = data;
+
+	ctx->plugged_cb = fn;
+	ctx->codec_dev = codec_dev;
+	anx7625_audio_update_connector_status(ctx, anx7625_sink_detect(ctx));
+
+	return 0;
+}
+
+static const struct hdmi_codec_ops anx7625_codec_ops = {
+	.hw_params	= anx7625_audio_hw_params,
+	.audio_shutdown = anx7625_audio_shutdown,
+	.get_dai_id	= anx7625_hdmi_i2s_get_dai_id,
+	.hook_plugged_cb = anx7625_audio_hook_plugged_cb,
+};
+
+static void anx7625_unregister_audio(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+
+	if (ctx->audio_pdev) {
+		platform_device_unregister(ctx->audio_pdev);
+		ctx->audio_pdev = NULL;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "unbound to %s", HDMI_CODEC_DRV_NAME);
+}
+
+static int anx7625_register_audio(struct device *dev, struct anx7625_data *ctx)
+{
+	struct hdmi_codec_pdata codec_data = {
+		.ops = &anx7625_codec_ops,
+		.max_i2s_channels = 8,
+		.i2s = 1,
+		.data = ctx,
+	};
+
+	ctx->audio_pdev = platform_device_register_data(dev,
+							HDMI_CODEC_DRV_NAME,
+							PLATFORM_DEVID_AUTO,
+							&codec_data,
+							sizeof(codec_data));
+
+	if (IS_ERR(ctx->audio_pdev))
+		return IS_ERR(ctx->audio_pdev);
+
+	DRM_DEV_DEBUG_DRIVER(dev, "bound to %s", HDMI_CODEC_DRV_NAME);
+
+	return 0;
+}
+
 static int anx7625_attach_dsi(struct anx7625_data *ctx)
 {
 	struct mipi_dsi_device *dsi;

@@ -2062,6 +2283,9 @@ static int anx7625_i2c_probe(struct i2c_client *client,
 				    DRM_MODE_CONNECTOR_DisplayPort;
 	drm_bridge_add(&platform->bridge);
 
+	if (platform->pdata.audio_en)
+		anx7625_register_audio(dev, platform);
+
 	DRM_DEV_DEBUG_DRIVER(dev, "probe done\n");
 
 	return 0;

@@ -2087,6 +2311,9 @@ static int anx7625_i2c_remove(struct i2c_client *client)
 
 	anx7625_unregister_i2c_dummy_clients(platform);
 
+	if (platform->pdata.audio_en)
+		anx7625_unregister_audio(platform);
+
 	kfree(platform);
 	return 0;
 }

index c6f93e4..d6be2a8 100644
@@ -111,6 +111,7 @@
 #define AUDIO_CHANNEL_STATUS_6 0xd5
 #define TDM_SLAVE_MODE 0x10
 #define I2S_SLAVE_MODE 0x08
+#define AUDIO_LAYOUT   0x01
 
 #define AUDIO_CONTROL_REGISTER 0xe6
 #define TDM_TIMING_MODE 0x08

@@ -400,6 +401,7 @@ struct anx7625_platform_data {
 	int intp_irq;
 	int is_dpi;
 	int mipi_lanes;
+	int audio_en;
 	int dp_lane0_swing_reg_cnt;
 	int lane0_reg_data[DP_TX_SWING_REG_CNT];
 	int dp_lane1_swing_reg_cnt;

@@ -420,6 +422,7 @@ struct anx7625_i2c_client {
 
 struct anx7625_data {
 	struct anx7625_platform_data pdata;
+	struct platform_device *audio_pdev;
 	atomic_t power_status;
 	int hpd_status;
 	int hpd_high_cnt;

@@ -429,6 +432,8 @@ struct anx7625_data {
 	struct anx7625_i2c_client i2c;
 	struct i2c_client *last_client;
 	struct s_edid_data slimport_edid_p;
+	struct device *codec_dev;
+	hdmi_codec_plugged_cb plugged_cb;
 	struct work_struct work;
 	struct workqueue_struct *workqueue;
 	char edid_block;