NVIDIA Tegra memory improvements
v3 cover NVIDIA Tegra memory improvements
Hi,
Here is the last patch of the series which had minor problem in v2, the rest of the patches are already applied by Krzysztof Kozlowski.
Changelog:
v3: - Added new optional reg property for emc-tables nodes in order to
fix dt_binding_check warning.
Please note that I will prepare a separate patch for v5.14 that will add the new property to the device-trees since Thierry already sent out PR for v5.13.
v2: - Fixed typos in the converted schemas.
- Corrected reg entry of tegra20-mc-gart schema to use fixed number of items.
- Made power-domain to use maxItems instead of $ref phandle in schemas.
Dmitry Osipenko (1):
dt-bindings: memory: tegra20: emc: Convert to schema
.../memory-controllers/nvidia,tegra20-emc.txt | 130 -------- .../nvidia,tegra20-emc.yaml | 303 ++++++++++++++++++ 2 files changed, 303 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml
Signature · 1 line
2.30.2
PATCH v3 1/1 dt-bindings: memory: tegra20: emc: Convert to schema
Convert Tegra20 External Memory Controller binding to schema.
Signed-off-by Dmitry Osipenko <[email protected]>
--- .../memory-controllers/nvidia,tegra20-emc.txt | 130 -------- .../nvidia,tegra20-emc.yaml | 303 ++++++++++++++++++ 2 files changed, 303 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml
Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.txt deleted +0 -130
@@ -1,130 +0,0 @@ -Embedded Memory Controller - -Properties: -- name : Should be emc -- #address-cells : Should be 1 -- #size-cells : Should be 0 -- compatible : Should contain "nvidia,tegra20-emc". -- reg : Offset and length of the register set for the device -- nvidia,use-ram-code : If present, the sub-nodes will be addressed - and chosen using the ramcode board selector. If omitted, only one - set of tables can be present and said tables will be used - irrespective of ram-code configuration. -- interrupts : Should contain EMC General interrupt. -- clocks : Should contain EMC clock. -- nvidia,memory-controller : Phandle of the Memory Controller node. -- #interconnect-cells : Should be 0. -- operating-points-v2: See ../bindings/opp/opp.txt for details. - -For each opp entry in 'operating-points-v2' table: -- opp-supported-hw: One bitfield indicating SoC process ID mask - - A bitwise AND is performed against this value and if any bit - matches, the OPP gets enabled. - -Optional properties: -- power-domains: Phandle of the SoC "core" power domain. - -Child device nodes describe the memory settings for different configurations and clock rates. - -Example: - - opp_table: opp-table { - compatible = "operating-points-v2"; - - opp@36000000 { - opp-microvolt = <950000 950000 1300000>; - opp-hz = /bits/ 64 <36000000>; - }; - ... - }; - - memory-controller@7000f400 { - #address-cells = < 1 >; - #size-cells = < 0 >; - #interconnect-cells = <0>; - compatible = "nvidia,tegra20-emc"; - reg = <0x7000f400 0x400>; - interrupts = <0 78 0x04>; - clocks = <&tegra_car TEGRA20_CLK_EMC>; - nvidia,memory-controller = <&mc>; - power-domains = <&domain>; - operating-points-v2 = <&opp_table>; - } - - -Embedded Memory Controller ram-code table - -If the emc node has the nvidia,use-ram-code property present, then the -next level of nodes below the emc table are used to specify which settings -apply for which ram-code settings. - -If the emc node lacks the nvidia,use-ram-code property, this level is omitted -and the tables are stored directly under the emc node (see below). - -Properties: - -- name : Should be emc-tables -- nvidia,ram-code : the binary representation of the ram-code board strappings - for which this node (and children) are valid. - - - -Embedded Memory Controller configuration table - -This is a table containing the EMC register settings for the various -operating speeds of the memory controller. They are always located as -subnodes of the emc controller node. - -There are two ways of specifying which tables to use: - -* The simplest is if there is just one set of tables in the device tree, - and they will always be used (based on which frequency is used). - This is the preferred method, especially when firmware can fill in - this information based on the specific system information and just - pass it on to the kernel. - -* The slightly more complex one is when more than one memory configuration - might exist on the system. The Tegra20 platform handles this during - early boot by selecting one out of possible 4 memory settings based - on a 2-pin "ram code" bootstrap setting on the board. The values of - these strappings can be read through a register in the SoC, and thus - used to select which tables to use. - -Properties: -- name : Should be emc-table -- compatible : Should contain "nvidia,tegra20-emc-table". -- reg : either an opaque enumerator to tell different tables apart, or - the valid frequency for which the table should be used (in kHz). -- clock-frequency : the clock frequency for the EMC at which this - table should be used (in kHz). -- nvidia,emc-registers : a 46 word array of EMC registers to be programmed - for operation at the 'clock-frequency' setting. - The order and contents of the registers are: - RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT, - WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR, - PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW, - TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE, - ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE, - ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0, - CFG_CLKTRIM_1, CFG_CLKTRIM_2 - - emc-table@166000 { - reg = <166000>; - compatible = "nvidia,tegra20-emc-table"; - clock-frequency = < 166000 >; - nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 >; - }; - - emc-table@333000 { - reg = <333000>; - compatible = "nvidia,tegra20-emc-table"; - clock-frequency = < 333000 >; - nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 >; - };
Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml new file +303 -0
303 lines not on this page · raw message
Signature · 1 line
2.30.2
Rob Herring
maintainerRe: [PATCH v3 1/1] dt-bindings: memory: tegra20: emc: Convert to schema
Quoted 206 lines · Dmitry Osipenko
Convert Tegra20 External Memory Controller binding to schema.
Signed-off-by Dmitry Osipenko <[email protected]>--- .../memory-controllers/nvidia,tegra20-emc.txt | 130 -------- .../nvidia,tegra20-emc.yaml | 303 ++++++++++++++++++ 2 files changed, 303 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yamlDocumentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.txt deleted +0
-130@@ -1,130 +0,0 @@ -Embedded Memory Controller - -Properties: -- name : Should be emc -- #address-cells : Should be 1 -- #size-cells : Should be 0 -- compatible : Should contain "nvidia,tegra20-emc". -- reg : Offset and length of the register set for the device -- nvidia,use-ram-code : If present, the sub-nodes will be addressed - and chosen using the ramcode board selector. If omitted, only one - set of tables can be present and said tables will be used - irrespective of ram-code configuration. -- interrupts : Should contain EMC General interrupt. -- clocks : Should contain EMC clock. -- nvidia,memory-controller : Phandle of the Memory Controller node. -- #interconnect-cells : Should be 0. -- operating-points-v2: See ../bindings/opp/opp.txt for details. - -For each opp entry in 'operating-points-v2' table: -- opp-supported-hw: One bitfield indicating SoC process ID mask - - A bitwise AND is performed against this value and if any bit - matches, the OPP gets enabled. - -Optional properties: -- power-domains: Phandle of the SoC "core" power domain. - -Child device nodes describe the memory settings for different configurations and clock rates. - -Example: - - opp_table: opp-table { - compatible = "operating-points-v2"; - - opp@36000000 { - opp-microvolt = <950000 950000 1300000>; - opp-hz = /bits/ 64 <36000000>; - }; - ... - }; - - memory-controller@7000f400 { - #address-cells = < 1 >; - #size-cells = < 0 >; - #interconnect-cells = <0>; - compatible = "nvidia,tegra20-emc"; - reg = <0x7000f400 0x400>; - interrupts = <0 78 0x04>; - clocks = <&tegra_car TEGRA20_CLK_EMC>; - nvidia,memory-controller = <&mc>; - power-domains = <&domain>; - operating-points-v2 = <&opp_table>; - } - - -Embedded Memory Controller ram-code table - -If the emc node has the nvidia,use-ram-code property present, then the -next level of nodes below the emc table are used to specify which settings -apply for which ram-code settings. - -If the emc node lacks the nvidia,use-ram-code property, this level is omitted -and the tables are stored directly under the emc node (see below). - -Properties: - -- name : Should be emc-tables -- nvidia,ram-code : the binary representation of the ram-code board strappings - for which this node (and children) are valid. - - - -Embedded Memory Controller configuration table - -This is a table containing the EMC register settings for the various -operating speeds of the memory controller. They are always located as -subnodes of the emc controller node. - -There are two ways of specifying which tables to use: - -* The simplest is if there is just one set of tables in the device tree, - and they will always be used (based on which frequency is used). - This is the preferred method, especially when firmware can fill in - this information based on the specific system information and just - pass it on to the kernel. - -* The slightly more complex one is when more than one memory configuration - might exist on the system. The Tegra20 platform handles this during - early boot by selecting one out of possible 4 memory settings based - on a 2-pin "ram code" bootstrap setting on the board. The values of - these strappings can be read through a register in the SoC, and thus - used to select which tables to use. - -Properties: -- name : Should be emc-table -- compatible : Should contain "nvidia,tegra20-emc-table". -- reg : either an opaque enumerator to tell different tables apart, or - the valid frequency for which the table should be used (in kHz). -- clock-frequency : the clock frequency for the EMC at which this - table should be used (in kHz). -- nvidia,emc-registers : a 46 word array of EMC registers to be programmed - for operation at the 'clock-frequency' setting. - The order and contents of the registers are: - RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT, - WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR, - PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW, - TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE, - ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE, - ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0, - CFG_CLKTRIM_1, CFG_CLKTRIM_2 - - emc-table@166000 { - reg = <166000>; - compatible = "nvidia,tegra20-emc-table"; - clock-frequency = < 166000 >; - nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 >; - }; - - emc-table@333000 { - reg = <333000>; - compatible = "nvidia,tegra20-emc-table"; - clock-frequency = < 333000 >; - nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 >; - };Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml new file +54
-0@@ -0,0 +1,303 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra20-emc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra20 SoC External Memory Controller + +maintainers: + - Dmitry Osipenko <[email protected]> + - Jon Hunter <[email protected]> + - Thierry Reding <[email protected]> + +description: | + The External Memory Controller (EMC) interfaces with the off-chip SDRAM to + service the request stream sent from Memory Controller. The EMC also has + various performance-affecting settings beyond the obvious SDRAM configuration + parameters and initialization settings. Tegra20 EMC supports multiple JEDEC + standard protocols: DDR1, LPDDR2 and DDR2. + +properties: + compatible: + const: nvidia,tegra20-emc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + "#interconnect-cells": + const: 0 + + nvidia,memory-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle of the Memory Controller node. + + power-domains: + maxItems: 1 + description: + Phandle of the SoC "core" power domain. + + operating-points-v2: + description:
Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml line 64
Quoted 10 lines
Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml new file +10
-0+ Should contain freqs and voltages and opp-supported-hw property, which + is a bitfield indicating SoC process ID mask. + + nvidia,use-ram-code: + type: boolean + description: + If present, the emc-tables@ sub-nodes will be addressed. + +patternProperties: + "^emc-table@[0-9]+$":
Duplicating this can be avoided. Change this to:
$defs:
emc-table:
And then do:
patternProperties:
"^emc-table@[0-9]+$":
$ref: #/$defs/emc-table
And the same later on.
Quoted 242 lines
Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml new file +239
-0+ type: object + properties: + compatible: + const: nvidia,tegra20-emc-table + + clock-frequency: + description: + Memory clock rate in kHz. + minimum: 1000 + maximum: 900000 + + reg: + maxItems: 1 + description: + Either an opaque enumerator to tell different tables apart, or + the valid frequency for which the table should be used (in kHz). + + nvidia,emc-registers: + description: + EMC timing characterization data. These are the registers + (see section "15.4.1 EMC Registers" in the TRM) whose values + need to be specified, according to the board documentation. + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: EMC_RC + - description: EMC_RFC + - description: EMC_RAS + - description: EMC_RP + - description: EMC_R2W + - description: EMC_W2R + - description: EMC_R2P + - description: EMC_W2P + - description: EMC_RD_RCD + - description: EMC_WR_RCD + - description: EMC_RRD + - description: EMC_REXT + - description: EMC_WDV + - description: EMC_QUSE + - description: EMC_QRST + - description: EMC_QSAFE + - description: EMC_RDV + - description: EMC_REFRESH + - description: EMC_BURST_REFRESH_NUM + - description: EMC_PDEX2WR + - description: EMC_PDEX2RD + - description: EMC_PCHG2PDEN + - description: EMC_ACT2PDEN + - description: EMC_AR2PDEN + - description: EMC_RW2PDEN + - description: EMC_TXSR + - description: EMC_TCKE + - description: EMC_TFAW + - description: EMC_TRPAB + - description: EMC_TCLKSTABLE + - description: EMC_TCLKSTOP + - description: EMC_TREFBW + - description: EMC_QUSE_EXTRA + - description: EMC_FBIO_CFG6 + - description: EMC_ODT_WRITE + - description: EMC_ODT_READ + - description: EMC_FBIO_CFG5 + - description: EMC_CFG_DIG_DLL + - description: EMC_DLL_XFORM_DQS + - description: EMC_DLL_XFORM_QUSE + - description: EMC_ZCAL_REF_CNT + - description: EMC_ZCAL_WAIT_CNT + - description: EMC_AUTO_CAL_INTERVAL + - description: EMC_CFG_CLKTRIM_0 + - description: EMC_CFG_CLKTRIM_1 + - description: EMC_CFG_CLKTRIM_2 + + required: + - clock-frequency + - compatible + - reg + - nvidia,emc-registers + + additionalProperties: false + + "^emc-tables@[a-z0-9-]+$": + type: object + properties: + reg: + maxItems: 1 + description: + An opaque enumerator to tell different tables apart. + + nvidia,ram-code: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Value of RAM_CODE this timing set is used for. + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + patternProperties: + "^emc-table@[0-9]+$": + type: object + properties: + compatible: + const: nvidia,tegra20-emc-table + + clock-frequency: + description: + Memory clock rate in kHz. + minimum: 1000 + maximum: 900000 + + reg: + maxItems: 1 + description: + Either an opaque enumerator to tell different tables apart, or + the valid frequency for which the table should be used (in kHz). + + nvidia,emc-registers: + description: + EMC timing characterization data. These are the registers + (see section "15.4.1 EMC Registers" in the TRM) whose values + need to be specified, according to the board documentation. + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + - description: EMC_RC + - description: EMC_RFC + - description: EMC_RAS + - description: EMC_RP + - description: EMC_R2W + - description: EMC_W2R + - description: EMC_R2P + - description: EMC_W2P + - description: EMC_RD_RCD + - description: EMC_WR_RCD + - description: EMC_RRD + - description: EMC_REXT + - description: EMC_WDV + - description: EMC_QUSE + - description: EMC_QRST + - description: EMC_QSAFE + - description: EMC_RDV + - description: EMC_REFRESH + - description: EMC_BURST_REFRESH_NUM + - description: EMC_PDEX2WR + - description: EMC_PDEX2RD + - description: EMC_PCHG2PDEN + - description: EMC_ACT2PDEN + - description: EMC_AR2PDEN + - description: EMC_RW2PDEN + - description: EMC_TXSR + - description: EMC_TCKE + - description: EMC_TFAW + - description: EMC_TRPAB + - description: EMC_TCLKSTABLE + - description: EMC_TCLKSTOP + - description: EMC_TREFBW + - description: EMC_QUSE_EXTRA + - description: EMC_FBIO_CFG6 + - description: EMC_ODT_WRITE + - description: EMC_ODT_READ + - description: EMC_FBIO_CFG5 + - description: EMC_CFG_DIG_DLL + - description: EMC_DLL_XFORM_DQS + - description: EMC_DLL_XFORM_QUSE + - description: EMC_ZCAL_REF_CNT + - description: EMC_ZCAL_WAIT_CNT + - description: EMC_AUTO_CAL_INTERVAL + - description: EMC_CFG_CLKTRIM_0 + - description: EMC_CFG_CLKTRIM_1 + - description: EMC_CFG_CLKTRIM_2 + + required: + - clock-frequency + - compatible + - reg + - nvidia,emc-registers + + additionalProperties: false + + required: + - nvidia,ram-code + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - nvidia,memory-controller + - "#interconnect-cells" + - operating-points-v2 + +additionalProperties: false + +examples: + - | + external-memory-controller@7000f400 { + compatible = "nvidia,tegra20-emc"; + reg = <0x7000f400 0x400>; + interrupts = <0 78 4>; + clocks = <&clock_controller 57>; + + nvidia,memory-controller = <&mc>; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; + + #interconnect-cells = <0>; + #address-cells = <1>; + #size-cells = <0>; + + nvidia,use-ram-code; + + emc-tables@0 { + nvidia,ram-code = <0>; + reg = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + emc-table@333000 { + reg = <333000>; + compatible = "nvidia,tegra20-emc-table"; + clock-frequency = <333000>; + nvidia,emc-registers = <0x00000018 0x00000033 + 0x00000012 0x00000004 0x00000004 0x00000005 + 0x00000003 0x0000000c 0x00000006 0x00000006 + 0x00000003 0x00000001 0x00000004 0x00000005 + 0x00000004 0x00000009 0x0000000d 0x00000bff + 0x00000000 0x00000003 0x00000003 0x00000006 + 0x00000006 0x00000001 0x00000011 0x000000c8 + 0x00000003 0x0000000e 0x00000007 0x00000008 + 0x00000002 0x00000000 0x00000000 0x00000002 + 0x00000000 0x00000000 0x00000083 0xf0440303 + 0x007fe010 0x00001414 0x00000000 0x00000000 + 0x00000000 0x00000000 0x00000000 0x00000000>; + }; + }; + };Signature · 1 line
2.30.2
Re: [PATCH v3 1/1] dt-bindings: memory: tegra20: emc: Convert to schema
08.04.2021 23:29, Rob Herring пишет:
Quoted 224 lines · Dmitry Osipenko
Quoted 206 lines
Convert Tegra20 External Memory Controller binding to schema.
Signed-off-by Dmitry Osipenko <[email protected]>--- .../memory-controllers/nvidia,tegra20-emc.txt | 130 -------- .../nvidia,tegra20-emc.yaml | 303 ++++++++++++++++++ 2 files changed, 303 insertions(+), 130 deletions(-) delete mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yamlDocumentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.txt deleted +0
-130@@ -1,130 +0,0 @@ -Embedded Memory Controller - -Properties: -- name : Should be emc -- #address-cells : Should be 1 -- #size-cells : Should be 0 -- compatible : Should contain "nvidia,tegra20-emc". -- reg : Offset and length of the register set for the device -- nvidia,use-ram-code : If present, the sub-nodes will be addressed - and chosen using the ramcode board selector. If omitted, only one - set of tables can be present and said tables will be used - irrespective of ram-code configuration. -- interrupts : Should contain EMC General interrupt. -- clocks : Should contain EMC clock. -- nvidia,memory-controller : Phandle of the Memory Controller node. -- #interconnect-cells : Should be 0. -- operating-points-v2: See ../bindings/opp/opp.txt for details. - -For each opp entry in 'operating-points-v2' table: -- opp-supported-hw: One bitfield indicating SoC process ID mask - - A bitwise AND is performed against this value and if any bit - matches, the OPP gets enabled. - -Optional properties: -- power-domains: Phandle of the SoC "core" power domain. - -Child device nodes describe the memory settings for different configurations and clock rates. - -Example: - - opp_table: opp-table { - compatible = "operating-points-v2"; - - opp@36000000 { - opp-microvolt = <950000 950000 1300000>; - opp-hz = /bits/ 64 <36000000>; - }; - ... - }; - - memory-controller@7000f400 { - #address-cells = < 1 >; - #size-cells = < 0 >; - #interconnect-cells = <0>; - compatible = "nvidia,tegra20-emc"; - reg = <0x7000f400 0x400>; - interrupts = <0 78 0x04>; - clocks = <&tegra_car TEGRA20_CLK_EMC>; - nvidia,memory-controller = <&mc>; - power-domains = <&domain>; - operating-points-v2 = <&opp_table>; - } - - -Embedded Memory Controller ram-code table - -If the emc node has the nvidia,use-ram-code property present, then the -next level of nodes below the emc table are used to specify which settings -apply for which ram-code settings. - -If the emc node lacks the nvidia,use-ram-code property, this level is omitted -and the tables are stored directly under the emc node (see below). - -Properties: - -- name : Should be emc-tables -- nvidia,ram-code : the binary representation of the ram-code board strappings - for which this node (and children) are valid. - - - -Embedded Memory Controller configuration table - -This is a table containing the EMC register settings for the various -operating speeds of the memory controller. They are always located as -subnodes of the emc controller node. - -There are two ways of specifying which tables to use: - -* The simplest is if there is just one set of tables in the device tree, - and they will always be used (based on which frequency is used). - This is the preferred method, especially when firmware can fill in - this information based on the specific system information and just - pass it on to the kernel. - -* The slightly more complex one is when more than one memory configuration - might exist on the system. The Tegra20 platform handles this during - early boot by selecting one out of possible 4 memory settings based - on a 2-pin "ram code" bootstrap setting on the board. The values of - these strappings can be read through a register in the SoC, and thus - used to select which tables to use. - -Properties: -- name : Should be emc-table -- compatible : Should contain "nvidia,tegra20-emc-table". -- reg : either an opaque enumerator to tell different tables apart, or - the valid frequency for which the table should be used (in kHz). -- clock-frequency : the clock frequency for the EMC at which this - table should be used (in kHz). -- nvidia,emc-registers : a 46 word array of EMC registers to be programmed - for operation at the 'clock-frequency' setting. - The order and contents of the registers are: - RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT, - WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR, - PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW, - TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE, - ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE, - ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0, - CFG_CLKTRIM_1, CFG_CLKTRIM_2 - - emc-table@166000 { - reg = <166000>; - compatible = "nvidia,tegra20-emc-table"; - clock-frequency = < 166000 >; - nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 >; - }; - - emc-table@333000 { - reg = <333000>; - compatible = "nvidia,tegra20-emc-table"; - clock-frequency = < 333000 >; - nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 0 0 0 0 >; - };Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml new file +54
-0@@ -0,0 +1,303 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra20-emc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra20 SoC External Memory Controller + +maintainers: + - Dmitry Osipenko <[email protected]> + - Jon Hunter <[email protected]> + - Thierry Reding <[email protected]> + +description: | + The External Memory Controller (EMC) interfaces with the off-chip SDRAM to + service the request stream sent from Memory Controller. The EMC also has + various performance-affecting settings beyond the obvious SDRAM configuration + parameters and initialization settings. Tegra20 EMC supports multiple JEDEC + standard protocols: DDR1, LPDDR2 and DDR2. + +properties: + compatible: + const: nvidia,tegra20-emc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + "#interconnect-cells": + const: 0 + + nvidia,memory-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle of the Memory Controller node. + + power-domains: + maxItems: 1 + description: + Phandle of the SoC "core" power domain. + + operating-points-v2: + description:Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml line 64
Quoted 10 lines
Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-emc.yaml new file +10
-0+ Should contain freqs and voltages and opp-supported-hw property, which + is a bitfield indicating SoC process ID mask. + + nvidia,use-ram-code: + type: boolean + description: + If present, the emc-tables@ sub-nodes will be addressed. + +patternProperties: + "^emc-table@[0-9]+$":Duplicating this can be avoided. Change this to:
$defs:
emc-table:
Quoted 7 lines
And then do:
patternProperties:
"^emc-table@[0-9]+$":$ref: #/$defs/emc-tableAnd the same later on.
Thank you, I'll try that variant.