Device driver location for the PCIe root port's DMA engine
Subsystems (2)
Hi
I'm starting this mail to seek advice on the best approach to be taken to add support for the driver of the PCIe root port's DMA engine.
To give some background, Tegra194's PCIe IPs are dual-mode PCIe IPs i.e. they work either in the root port mode or in the endpoint mode based on the boot time configuration.
Since the PCIe hardware IP as such is the same for both (RP and EP) modes, the DMA engine sub-system of the PCIe IP is also made available to both modes of operation.
Typically, the DMA engine is seen only in the endpoint mode, and that DMA engine’s configuration registers are made available to the host through one of its BARs.
In the situation that we have here, where there is a DMA engine present as part of the root port, the DMA engine isn’t a typical general-purpose DMA engine in the sense that it can’t have both source and destination addresses targeting external memory addresses. RP’s DMA engine, while doing a write operation,
would always fetch data (i.e. source) from local memory and write it to the remote memory over PCIe link (i.e. destination would be the BAR of an endpoint)
whereas while doing a read operation,
would always fetch/read data (i.e. source) from a remote memory over the PCIe link and write it to the local memory.
I see that there are at least two ways we can have a driver for this DMA engine.
a) DMA engine driver as one of the port service drivers
Since the DMA engine is a part of the root port hardware itself
(although it is not part of the standard capabilities of the root port), it is one of the options to have the driver for the DMA engine go as one of the port service drivers (along with AER, PME, hot-plug, etc...). Based on Vendor-ID and Device-ID matching runtime, either it gets binded/enabled (like in the case of Tegra194) or it doesn't.
b) DMA engine driver as a platform driver
The DMA engine hardware can be described as a sub-node under the PCIe
controller's node in the device tree and a separate platform driver can be written to work with it.
I’m inclined to have the DMA engine driver as a port service driver as it makes it cleaner and also in line with the design philosophy (the way I understood it) of the port service drivers. Please let me know your thoughts on this.
Thanks,
Vidya Sagar
[+cc Matthew for portdrv comment]
Quoted 38 lines · Vidya Sagar
Hi
I'm starting this mail to seek advice on the best approach to be taken to add support for the driver of the PCIe root port's DMA engine. To give some background, Tegra194's PCIe IPs are dual-mode PCIe IPs i.e. they work either in the root port mode or in the endpoint mode based on the boot time configuration.
Since the PCIe hardware IP as such is the same for both (RP and EP) modes, the DMA engine sub-system of the PCIe IP is also made available to both modes of operation.
Typically, the DMA engine is seen only in the endpoint mode, and that DMA engine’s configuration registers are made available to the host through one of its BARs.
In the situation that we have here, where there is a DMA engine present as part of the root port, the DMA engine isn’t a typical general-purpose DMA engine in the sense that it can’t have both source and destination addresses targeting external memory addresses.
RP’s DMA engine, while doing a write operation,
would always fetch data (i.e. source) from local memory and write it to the remote memory over PCIe link (i.e. destination would be the BAR of an endpoint)
whereas while doing a read operation,
would always fetch/read data (i.e. source) from a remote memory over the PCIe link and write it to the local memory.I see that there are at least two ways we can have a driver for this DMA engine.
a) DMA engine driver as one of the port service drivers
Since the DMA engine is a part of the root port hardware itself (although
it is not part of the standard capabilities of the root port), it is one of the options to have the driver for the DMA engine go as one of the port service drivers (along with AER, PME, hot-plug, etc...). Based on Vendor-ID and Device-ID matching runtime, either it gets binded/enabled (like in the case of Tegra194) or it doesn't.
b) DMA engine driver as a platform driver
The DMA engine hardware can be described as a sub-node under the PCIe
controller's node in the device tree and a separate platform driver can be written to work with it.
Quoted 4 lines
I’m inclined to have the DMA engine driver as a port service driver as it makes it cleaner and also in line with the design philosophy (the way I understood it) of the port service drivers.
Please let me know your thoughts on this.
Personally I'm not a fan of the port service driver model. It creates additional struct devices for things that are not separate devices. And it creates a parallel hierarchy in /sys/bus/pci_express/devices/ that I think does not accurately model the hardware.
The existing port services (AER, DPC, hotplug, etc) are things the device advertises via the PCI Capabilities defined by the generic PCIe spec, and in my opinion the support for them should be directly part of the PCI core and activated when the relevant Capability is present.
The DMA engine is different -- this is device-specific functionality and I think the obvious way to discover it and bind a driver to it is via the PCI Vendor and Device ID.
This *is* complicated by the fact that you can't just use pci_register_driver() to claim functionality implemented in Root Ports or Switch Ports because portdrv binds to them before you have a chance. I think that's a defect in the portdrv design. The usual workaround is to use pci_get_device(), which has its own issues (it's ugly, it's outside the normal driver binding model, doesn't work nicely with hotplug or udev, doesn't coordinate with other drivers using the same device, etc). There are many examples of this in the EDAC code.
Bjorn
Quoted 49 lines · Bjorn Helgaas
External email: Use caution opening links or attachments
[+cc Matthew for portdrv comment]
Quoted 38 lines · Vidya Sagar
Hi
I'm starting this mail to seek advice on the best approach to be taken to add support for the driver of the PCIe root port's DMA engine. To give some background, Tegra194's PCIe IPs are dual-mode PCIe IPs i.e. they work either in the root port mode or in the endpoint mode based on the boot time configuration.
Since the PCIe hardware IP as such is the same for both (RP and EP) modes, the DMA engine sub-system of the PCIe IP is also made available to both modes of operation.
Typically, the DMA engine is seen only in the endpoint mode, and that DMA engine’s configuration registers are made available to the host through one of its BARs.
In the situation that we have here, where there is a DMA engine present as part of the root port, the DMA engine isn’t a typical general-purpose DMA engine in the sense that it can’t have both source and destination addresses targeting external memory addresses.
RP’s DMA engine, while doing a write operation,
would always fetch data (i.e. source) from local memory and write it to the remote memory over PCIe link (i.e. destination would be the BAR of an endpoint)
whereas while doing a read operation,
would always fetch/read data (i.e. source) from a remote memory over the PCIe link and write it to the local memory.I see that there are at least two ways we can have a driver for this DMA engine.
a) DMA engine driver as one of the port service drivers
Since the DMA engine is a part of the root port hardware itself (although
it is not part of the standard capabilities of the root port), it is one of the options to have the driver for the DMA engine go as one of the port service drivers (along with AER, PME, hot-plug, etc...). Based on Vendor-ID and Device-ID matching runtime, either it gets binded/enabled (like in the case of Tegra194) or it doesn't.
b) DMA engine driver as a platform driver
The DMA engine hardware can be described as a sub-node under the PCIe
controller's node in the device tree and a separate platform driver can be written to work with it.Quoted 4 lines
I’m inclined to have the DMA engine driver as a port service driver as it makes it cleaner and also in line with the design philosophy (the way I understood it) of the port service drivers.
Please let me know your thoughts on this.
Quoted 4 lines
Personally I'm not a fan of the port service driver model. It creates additional struct devices for things that are not separate devices. And it creates a parallel hierarchy in
/sys/bus/pci_express/devices/that I think does not accurately model the hardware.
Agree.
Quoted 5 lines
The existing port services (AER, DPC, hotplug, etc) are things the device advertises via the PCI Capabilities defined by the generic PCIe spec, and in my opinion the support for them should be directly part of the PCI core and activated when the relevant Capability is present.
Is there an on-going activity to remove port service drivers are move AER/DPC/Hotplug etc.. handling within PCI core?
Quoted 9 lines
The DMA engine is different -- this is device-specific functionality and I think the obvious way to discover it and bind a driver to it is via the PCI Vendor and Device ID.
This *is* complicated by the fact that you can't just use
pci_register_driver()to claim functionality implemented in Root Ports or Switch Ports because portdrv binds to them before you have a chance. I think that's a defect in the portdrv design. The usual
Yes. Hence I was thinking of adding a service driver for the DMA functionality
Quoted 5 lines
workaround is to use
pci_get_device(), which has its own issues (it's ugly, it's outside the normal driver binding model, doesn't work nicely with hotplug or udev, doesn't coordinate with other drivers using the same device, etc). There are many examples of this in the EDAC code.
I didn't think of approaching this issue in this way. Thanks for the pointers to EDAC code. I'll wait for comments from Matthew before I proceed with this approach.
Quoted 3 lines
Bjorn
Quoted 8 lines · Vidya Sagar
Quoted 4 lines · Bjorn Helgaas
The existing port services (AER, DPC, hotplug, etc) are things the device advertises via the PCI Capabilities defined by the generic PCIe spec, and in my opinion the support for them should be directly part of the PCI core and activated when the relevant Capability is present.
Is there an on-going activity to remove port service drivers are move AER/DPC/Hotplug etc.. handling within PCI core?
No, not that I'm aware of. I'd just like to avoid extending that model.
Bjorn
Quoted 25 lines · Vidya Sagar
Hi
I'm starting this mail to seek advice on the best approach to be taken to add support for the driver of the PCIe root port's DMA engine. To give some background, Tegra194's PCIe IPs are dual-mode PCIe IPs i.e. they work either in the root port mode or in the endpoint mode based on the boot time configuration.
Since the PCIe hardware IP as such is the same for both (RP and EP) modes, the DMA engine sub-system of the PCIe IP is also made available to both modes of operation.
Typically, the DMA engine is seen only in the endpoint mode, and that DMA engine’s configuration registers are made available to the host through one of its BARs.
In the situation that we have here, where there is a DMA engine present as part of the root port, the DMA engine isn’t a typical general-purpose DMA engine in the sense that it can’t have both source and destination addresses targeting external memory addresses.
RP’s DMA engine, while doing a write operation,
would always fetch data (i.e. source) from local memory and write it to the remote memory over PCIe link (i.e. destination would be the BAR of an endpoint)
whereas while doing a read operation,
would always fetch/read data (i.e. source) from a remote memory over the PCIe link and write it to the local memory.
Quoted 13 lines
I see that there are at least two ways we can have a driver for this DMA engine.
a) DMA engine driver as one of the port service drivers
Since the DMA engine is a part of the root port hardware itself
(although it is not part of the standard capabilities of the root port), it is one of the options to have the driver for the DMA engine go as one of the port service drivers (along with AER, PME, hot-plug, etc...). Based on Vendor-ID and Device-ID matching runtime, either it gets binded/enabled (like in the case of Tegra194) or it doesn't.
b) DMA engine driver as a platform driver
The DMA engine hardware can be described as a sub-node under the PCIe
controller's node in the device tree and a separate platform driver can be written to work with it.
DT expects PCI bridge child nodes to be a PCI device. We've already broken that with the interrupt controller child nodes, but I don't really want to add more.
Quoted 4 lines
I’m inclined to have the DMA engine driver as a port service driver as it makes it cleaner and also in line with the design philosophy (the way I understood it) of the port service drivers.
Please let me know your thoughts on this.
What is the actual usecase and benefit for using the DMA engine with the RP? The only one I've come up with is the hardware designers think having DMA is better than not having DMA so they include that option on the DWC controller.
Rob
Quoted 43 lines · Rob Herring
External email: Use caution opening links or attachments
Quoted 25 lines · Vidya Sagar
Hi
I'm starting this mail to seek advice on the best approach to be taken to add support for the driver of the PCIe root port's DMA engine. To give some background, Tegra194's PCIe IPs are dual-mode PCIe IPs i.e. they work either in the root port mode or in the endpoint mode based on the boot time configuration.
Since the PCIe hardware IP as such is the same for both (RP and EP) modes, the DMA engine sub-system of the PCIe IP is also made available to both modes of operation.
Typically, the DMA engine is seen only in the endpoint mode, and that DMA engine’s configuration registers are made available to the host through one of its BARs.
In the situation that we have here, where there is a DMA engine present as part of the root port, the DMA engine isn’t a typical general-purpose DMA engine in the sense that it can’t have both source and destination addresses targeting external memory addresses.
RP’s DMA engine, while doing a write operation,
would always fetch data (i.e. source) from local memory and write it to the remote memory over PCIe link (i.e. destination would be the BAR of an endpoint)
whereas while doing a read operation,
would always fetch/read data (i.e. source) from a remote memory over the PCIe link and write it to the local memory.Quoted 13 lines
I see that there are at least two ways we can have a driver for this DMA engine.
a) DMA engine driver as one of the port service drivers
Since the DMA engine is a part of the root port hardware itself
(although it is not part of the standard capabilities of the root port), it is one of the options to have the driver for the DMA engine go as one of the port service drivers (along with AER, PME, hot-plug, etc...). Based on Vendor-ID and Device-ID matching runtime, either it gets binded/enabled (like in the case of Tegra194) or it doesn't.
b) DMA engine driver as a platform driver
The DMA engine hardware can be described as a sub-node under the PCIe
controller's node in the device tree and a separate platform driver can be written to work with it.
Quoted 3 lines
DT expects PCI bridge child nodes to be a PCI device. We've already broken that with the interrupt controller child nodes, but I don't really want to add more.
Understood. Is there any other way of specifying the DMA functionality other than as a child node so that it is inline with the DT framework's expectations?
Quoted 10 lines
Quoted 5 lines
I’m inclined to have the DMA engine driver as a port service driver as it makes it cleaner and also in line with the design philosophy (the way I understood it) of the port service drivers.
Please let me know your thoughts on this.What is the actual usecase and benefit for using the DMA engine with the RP? The only one I've come up with is the hardware designers think having DMA is better than not having DMA so they include that option on the DWC controller.
In Tegra194-to-Tegra194 configuration (with one Tegra194 as RP and the other as EP) better performance is expected when DMA engines on both sides are used for pushing(writing) the data across instead of using only the EP's DMA engine for both push(write) and pull(read).
Quoted 3 lines
Rob