Skip to contentSkip to conversation

iio: adis16480: support burst read function

PATCH In review Nuno Sa 2 participants 6 messages Apr 22, 2021 – May 18, 2021

Subsystems (2)
lore
Share & tools
lore

Nuno Sa

author maintainer
#0 lore raw

PATCH v4 1/1 iio: adis16480: support burst read function

Some supported devices support burst read function. This provides a method for reading a batch of data (status, temperature, gyroscopes, accelerometers, time stamp/data counter, and CRC code), which does not require a stall time between each 16-bit segment and only requires one command on the DIN line to initiate. Devices supporting this mode are:

* adis16495-1
* adis16495-2
* adis16495-3
* adis16497-1
* adis16497-2
* adis16497-3

---
Changes in v2:
* Return right away if offset == 4 (no valid transition found from
brurst_id to sys_flags).

Changes in v3:
* Move crc32.h header;
* Return proper 'irqreturn_t' types in all error paths;
* Move 'adis->current_page = 0' to right after setting it;
* Restore spi max transfer in case 'spi_sync()' fails;
* Use 80 line chars for 'devm_adis_setup_buffer_and_trigger()'.

Changes in v4:
* Rebased this patch on top of the series in [1]. Thus, we do not
need to directly change the spi max speed and avoid a potential race.

[1]: https://marc.info/?l=linux-iio&m=161908662424639&w=2

 drivers/iio/imu/adis16480.c | 160 +++++++++++++++++++++++++++++++++---
 1 file changed, 147 insertions(+), 13 deletions(-)
drivers/iio/imu/adis16480.c +147 -13
index f81b86690b76..a9c21a5ae05a 100644
@@ -19,11 +19,15 @@
 #include <linux/sysfs.h>
 #include <linux/module.h>
 #include <linux/lcm.h>
+#include <linux/swab.h>
+#include <linux/crc32.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/sysfs.h>
 #include <linux/iio/buffer.h>
 #include <linux/iio/imu/adis.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger_consumer.h>
 
 #include <linux/debugfs.h>
 
@@ -103,6 +107,12 @@
  * Available only for ADIS1649x devices
  */
 #define ADIS16495_REG_SYNC_SCALE		ADIS16480_REG(0x03, 0x10)
+#define ADIS16495_REG_BURST_CMD			ADIS16480_REG(0x00, 0x7C)
+#define ADIS16495_BURST_ID			0xA5A5
+/* total number of segments in burst */
+#define ADIS16495_BURST_MAX_DATA		20
+/* spi max speed in burst mode */
+#define ADIS16495_BURST_MAX_SPEED              6000000
 
 #define ADIS16480_REG_SERIAL_NUM		ADIS16480_REG(0x04, 0x20)
 
@@ -163,6 +173,8 @@ struct adis16480 {
 	struct clk *ext_clk;
 	enum adis16480_clock_mode clk_mode;
 	unsigned int clk_freq;
+	/* Alignment needed for the timestamp */
+	__be16 data[ADIS16495_BURST_MAX_DATA] __aligned(8);
 };
 
 static const char * const adis16480_int_pin_names[4] = {
@@ -863,7 +875,7 @@ static const char * const adis16480_status_error_msgs[] = {
 
 static int adis16480_enable_irq(struct adis *adis, bool enable);
 
-#define ADIS16480_DATA(_prod_id, _timeouts)				\
+#define ADIS16480_DATA(_prod_id, _timeouts, _burst_len)			\
 {									\
 	.diag_stat_reg = ADIS16480_REG_DIAG_STS,			\
 	.glob_cmd_reg = ADIS16480_REG_GLOB_CMD,				\
@@ -887,6 +899,9 @@ static int adis16480_enable_irq(struct adis *adis, bool enable);
 		BIT(ADIS16480_DIAG_STAT_BARO_FAIL),			\
 	.enable_irq = adis16480_enable_irq,				\
 	.timeouts = (_timeouts),					\
+	.burst_reg_cmd = ADIS16495_REG_BURST_CMD,			\
+	.burst_len = (_burst_len),					\
+	.burst_max_speed_hz = ADIS16495_BURST_MAX_SPEED			\
 }
 
 static const struct adis_timeout adis16485_timeouts = {
@@ -931,7 +946,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.int_clk = 2460000,
 		.max_dec_rate = 2048,
 		.filter_freqs = adis16480_def_filter_freqs,
-		.adis_data = ADIS16480_DATA(16375, &adis16485_timeouts),
+		.adis_data = ADIS16480_DATA(16375, &adis16485_timeouts, 0),
 	},
 	[ADIS16480] = {
 		.channels = adis16480_channels,
@@ -944,7 +959,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.int_clk = 2460000,
 		.max_dec_rate = 2048,
 		.filter_freqs = adis16480_def_filter_freqs,
-		.adis_data = ADIS16480_DATA(16480, &adis16480_timeouts),
+		.adis_data = ADIS16480_DATA(16480, &adis16480_timeouts, 0),
 	},
 	[ADIS16485] = {
 		.channels = adis16485_channels,
@@ -957,7 +972,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.int_clk = 2460000,
 		.max_dec_rate = 2048,
 		.filter_freqs = adis16480_def_filter_freqs,
-		.adis_data = ADIS16480_DATA(16485, &adis16485_timeouts),
+		.adis_data = ADIS16480_DATA(16485, &adis16485_timeouts, 0),
 	},
 	[ADIS16488] = {
 		.channels = adis16480_channels,
@@ -970,7 +985,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.int_clk = 2460000,
 		.max_dec_rate = 2048,
 		.filter_freqs = adis16480_def_filter_freqs,
-		.adis_data = ADIS16480_DATA(16488, &adis16485_timeouts),
+		.adis_data = ADIS16480_DATA(16488, &adis16485_timeouts, 0),
 	},
 	[ADIS16490] = {
 		.channels = adis16485_channels,
@@ -984,7 +999,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16490, &adis16495_timeouts),
+		.adis_data = ADIS16480_DATA(16490, &adis16495_timeouts, 0),
 	},
 	[ADIS16495_1] = {
 		.channels = adis16485_channels,
@@ -998,7 +1013,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16495_2] = {
 		.channels = adis16485_channels,
@@ -1012,7 +1029,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16495_3] = {
 		.channels = adis16485_channels,
@@ -1026,7 +1045,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16497_1] = {
 		.channels = adis16485_channels,
@@ -1040,7 +1061,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16497_2] = {
 		.channels = adis16485_channels,
@@ -1054,7 +1077,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16497_3] = {
 		.channels = adis16485_channels,
@@ -1068,10 +1093,118 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 };
 
+static bool adis16480_validate_crc(const u16 *buf, const u8 n_elem, const u32 crc)
+{
+	u32 crc_calc;
+	u16 crc_buf[15];
+	int j;
+
+	for (j = 0; j < n_elem; j++)
+		crc_buf[j] = swab16(buf[j]);
+
+	crc_calc = crc32(~0, crc_buf, n_elem * 2);
+	crc_calc ^= ~0;
+
+	return (crc == crc_calc);
+}
+
+static irqreturn_t adis16480_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct adis16480 *st = iio_priv(indio_dev);
+	struct adis *adis = &st->adis;
+	int ret, bit, offset, i = 0;
+	__be16 *buffer;
+	u32 crc;
+	bool valid;
+
+	adis_dev_lock(adis);
+	if (adis->current_page != 0) {
+		adis->tx[0] = ADIS_WRITE_REG(ADIS_REG_PAGE_ID);
+		adis->tx[1] = 0;
+		ret = spi_write(adis->spi, adis->tx, 2);
+		if (ret) {
+			dev_err(&adis->spi->dev, "Failed to change device page: %d\n", ret);
+			adis_dev_unlock(adis);
+			goto irq_done;
+		}
+
+		adis->current_page = 0;
+	}
+
+	ret = spi_sync(adis->spi, &adis->msg);
+	if (ret) {
+		dev_err(&adis->spi->dev, "Failed to read data: %d\n", ret);
+		adis_dev_unlock(adis);
+		goto irq_done;
+	}
+
+	adis_dev_unlock(adis);
+
+	/*
+	 * After making the burst request, the response can have one or two
+	 * 16-bit responses containing the BURST_ID depending on the sclk. If
+	 * clk > 3.6MHz, then we will have two BURST_ID in a row. If clk < 3MHZ,
+	 * we have only one. To manage that variation, we use the transition from the
+	 * BURST_ID to the SYS_E_FLAG register, which will not be equal to 0xA5A5. If
+	 * we not find this variation in the first 4 segments, then the data should
+	 * not be valid.
+	 */
+	buffer = adis->buffer;
+	for (offset = 0; offset < 4; offset++) {
+		u16 curr = be16_to_cpu(buffer[offset]);
+		u16 next = be16_to_cpu(buffer[offset + 1]);
+
+		if (curr == ADIS16495_BURST_ID && next != ADIS16495_BURST_ID) {
+			offset++;
+			break;
+		}
+	}
+
+	if (offset == 4) {
+		dev_err(&adis->spi->dev, "Invalid burst data\n");
+		goto irq_done;
+	}
+
+	crc = be16_to_cpu(buffer[offset + 16]) << 16 | be16_to_cpu(buffer[offset + 15]);
+	valid = adis16480_validate_crc((u16 *)&buffer[offset], 15, crc);
+	if (!valid) {
+		dev_err(&adis->spi->dev, "Invalid crc\n");
+		goto irq_done;
+	}
+
+	for_each_set_bit(bit, indio_dev->active_scan_mask, indio_dev->masklength) {
+		/*
+		 * When burst mode is used, temperature is the first data
+		 * channel in the sequence, but the temperature scan index
+		 * is 10.
+		 */
+		switch (bit) {
+		case ADIS16480_SCAN_TEMP:
+			st->data[i++] = buffer[offset + 1];
+			break;
+		case ADIS16480_SCAN_GYRO_X ... ADIS16480_SCAN_ACCEL_Z:
+			/* The lower register data is sequenced first */
+			st->data[i++] = buffer[2 * bit + offset + 3];
+			st->data[i++] = buffer[2 * bit + offset + 2];
+			break;
+		}
+	}
+
+	iio_push_to_buffers_with_timestamp(indio_dev, st->data, pf->timestamp);
+irq_done:
+	iio_trigger_notify_done(indio_dev->trig);
+
+	return IRQ_HANDLED;
+}
+
 static const struct iio_info adis16480_info = {
 	.read_raw = &adis16480_read_raw,
 	.write_raw = &adis16480_write_raw,
@@ -1341,7 +1474,8 @@ static int adis16480_probe(struct spi_device *spi)
 		st->clk_freq = st->chip_info->int_clk;
 	}
 
-	ret = devm_adis_setup_buffer_and_trigger(&st->adis, indio_dev, NULL);
+	ret = devm_adis_setup_buffer_and_trigger(&st->adis, indio_dev,
+						 adis16480_trigger_handler);
 	if (ret)
 		return ret;
 
Signature · 1 line
2.31.1
maintainer
#1 lore raw
Quoted 14 lines · On Thu, 22 Apr 2021 12:37:35 +0200 Nuno Sa <[email protected]> wrote:

Some supported devices support burst read function. This provides a method for reading a batch of data (status, temperature, gyroscopes, accelerometers, time stamp/data counter, and CRC code), which does not require a stall time between each 16-bit segment and only requires one command on the DIN line to initiate. Devices supporting this mode are:

* adis16495-1
* adis16495-2
* adis16495-3
* adis16497-1
* adis16497-2
* adis16497-3

Quoted 2 lines

Looks good to me. Give me a poke if I seem to have lost it when the dependency is in place.

Thanks,

Jonathan

Quoted 312 lines

---
Changes in v2:
* Return right away if offset == 4 (no valid transition found from
brurst_id to sys_flags).

Changes in v3:
* Move crc32.h header;
* Return proper 'irqreturn_t' types in all error paths;
* Move 'adis->current_page = 0' to right after setting it;
* Restore spi max transfer in case 'spi_sync()' fails;
* Use 80 line chars for 'devm_adis_setup_buffer_and_trigger()'.

Changes in v4:
* Rebased this patch on top of the series in [1]. Thus, we do not
need to directly change the spi max speed and avoid a potential race.

[1]: https://marc.info/?l=linux-iio&m=161908662424639&w=2

 drivers/iio/imu/adis16480.c | 160 +++++++++++++++++++++++++++++++++---
 1 file changed, 147 insertions(+), 13 deletions(-)
drivers/iio/imu/adis16480.c +147 -13
index f81b86690b76..a9c21a5ae05a 100644
@@ -19,11 +19,15 @@
 #include <linux/sysfs.h>
 #include <linux/module.h>
 #include <linux/lcm.h>
+#include <linux/swab.h>
+#include <linux/crc32.h>
 
 #include <linux/iio/iio.h>
 #include <linux/iio/sysfs.h>
 #include <linux/iio/buffer.h>
 #include <linux/iio/imu/adis.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger_consumer.h>
 
 #include <linux/debugfs.h>
 
@@ -103,6 +107,12 @@
  * Available only for ADIS1649x devices
  */
 #define ADIS16495_REG_SYNC_SCALE		ADIS16480_REG(0x03, 0x10)
+#define ADIS16495_REG_BURST_CMD			ADIS16480_REG(0x00, 0x7C)
+#define ADIS16495_BURST_ID			0xA5A5
+/* total number of segments in burst */
+#define ADIS16495_BURST_MAX_DATA		20
+/* spi max speed in burst mode */
+#define ADIS16495_BURST_MAX_SPEED              6000000
 
 #define ADIS16480_REG_SERIAL_NUM		ADIS16480_REG(0x04, 0x20)
 
@@ -163,6 +173,8 @@ struct adis16480 {
 	struct clk *ext_clk;
 	enum adis16480_clock_mode clk_mode;
 	unsigned int clk_freq;
+	/* Alignment needed for the timestamp */
+	__be16 data[ADIS16495_BURST_MAX_DATA] __aligned(8);
 };
 
 static const char * const adis16480_int_pin_names[4] = {
@@ -863,7 +875,7 @@ static const char * const adis16480_status_error_msgs[] = {
 
 static int adis16480_enable_irq(struct adis *adis, bool enable);
 
-#define ADIS16480_DATA(_prod_id, _timeouts)				\
+#define ADIS16480_DATA(_prod_id, _timeouts, _burst_len)			\
 {									\
 	.diag_stat_reg = ADIS16480_REG_DIAG_STS,			\
 	.glob_cmd_reg = ADIS16480_REG_GLOB_CMD,				\
@@ -887,6 +899,9 @@ static int adis16480_enable_irq(struct adis *adis, bool enable);
 		BIT(ADIS16480_DIAG_STAT_BARO_FAIL),			\
 	.enable_irq = adis16480_enable_irq,				\
 	.timeouts = (_timeouts),					\
+	.burst_reg_cmd = ADIS16495_REG_BURST_CMD,			\
+	.burst_len = (_burst_len),					\
+	.burst_max_speed_hz = ADIS16495_BURST_MAX_SPEED			\
 }
 
 static const struct adis_timeout adis16485_timeouts = {
@@ -931,7 +946,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.int_clk = 2460000,
 		.max_dec_rate = 2048,
 		.filter_freqs = adis16480_def_filter_freqs,
-		.adis_data = ADIS16480_DATA(16375, &adis16485_timeouts),
+		.adis_data = ADIS16480_DATA(16375, &adis16485_timeouts, 0),
 	},
 	[ADIS16480] = {
 		.channels = adis16480_channels,
@@ -944,7 +959,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.int_clk = 2460000,
 		.max_dec_rate = 2048,
 		.filter_freqs = adis16480_def_filter_freqs,
-		.adis_data = ADIS16480_DATA(16480, &adis16480_timeouts),
+		.adis_data = ADIS16480_DATA(16480, &adis16480_timeouts, 0),
 	},
 	[ADIS16485] = {
 		.channels = adis16485_channels,
@@ -957,7 +972,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.int_clk = 2460000,
 		.max_dec_rate = 2048,
 		.filter_freqs = adis16480_def_filter_freqs,
-		.adis_data = ADIS16480_DATA(16485, &adis16485_timeouts),
+		.adis_data = ADIS16480_DATA(16485, &adis16485_timeouts, 0),
 	},
 	[ADIS16488] = {
 		.channels = adis16480_channels,
@@ -970,7 +985,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.int_clk = 2460000,
 		.max_dec_rate = 2048,
 		.filter_freqs = adis16480_def_filter_freqs,
-		.adis_data = ADIS16480_DATA(16488, &adis16485_timeouts),
+		.adis_data = ADIS16480_DATA(16488, &adis16485_timeouts, 0),
 	},
 	[ADIS16490] = {
 		.channels = adis16485_channels,
@@ -984,7 +999,7 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16490, &adis16495_timeouts),
+		.adis_data = ADIS16480_DATA(16490, &adis16495_timeouts, 0),
 	},
 	[ADIS16495_1] = {
 		.channels = adis16485_channels,
@@ -998,7 +1013,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16495_2] = {
 		.channels = adis16485_channels,
@@ -1012,7 +1029,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16495_3] = {
 		.channels = adis16485_channels,
@@ -1026,7 +1045,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16495, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16497_1] = {
 		.channels = adis16485_channels,
@@ -1040,7 +1061,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16497_2] = {
 		.channels = adis16485_channels,
@@ -1054,7 +1077,9 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 	[ADIS16497_3] = {
 		.channels = adis16485_channels,
@@ -1068,10 +1093,118 @@ static const struct adis16480_chip_info adis16480_chip_info[] = {
 		.max_dec_rate = 4250,
 		.filter_freqs = adis16495_def_filter_freqs,
 		.has_pps_clk_mode = true,
-		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts),
+		/* 20 elements of 16bits */
+		.adis_data = ADIS16480_DATA(16497, &adis16495_1_timeouts,
+					    ADIS16495_BURST_MAX_DATA * 2),
 	},
 };
 
+static bool adis16480_validate_crc(const u16 *buf, const u8 n_elem, const u32 crc)
+{
+	u32 crc_calc;
+	u16 crc_buf[15];
+	int j;
+
+	for (j = 0; j < n_elem; j++)
+		crc_buf[j] = swab16(buf[j]);
+
+	crc_calc = crc32(~0, crc_buf, n_elem * 2);
+	crc_calc ^= ~0;
+
+	return (crc == crc_calc);
+}
+
+static irqreturn_t adis16480_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct adis16480 *st = iio_priv(indio_dev);
+	struct adis *adis = &st->adis;
+	int ret, bit, offset, i = 0;
+	__be16 *buffer;
+	u32 crc;
+	bool valid;
+
+	adis_dev_lock(adis);
+	if (adis->current_page != 0) {
+		adis->tx[0] = ADIS_WRITE_REG(ADIS_REG_PAGE_ID);
+		adis->tx[1] = 0;
+		ret = spi_write(adis->spi, adis->tx, 2);
+		if (ret) {
+			dev_err(&adis->spi->dev, "Failed to change device page: %d\n", ret);
+			adis_dev_unlock(adis);
+			goto irq_done;
+		}
+
+		adis->current_page = 0;
+	}
+
+	ret = spi_sync(adis->spi, &adis->msg);
+	if (ret) {
+		dev_err(&adis->spi->dev, "Failed to read data: %d\n", ret);
+		adis_dev_unlock(adis);
+		goto irq_done;
+	}
+
+	adis_dev_unlock(adis);
+
+	/*
+	 * After making the burst request, the response can have one or two
+	 * 16-bit responses containing the BURST_ID depending on the sclk. If
+	 * clk > 3.6MHz, then we will have two BURST_ID in a row. If clk < 3MHZ,
+	 * we have only one. To manage that variation, we use the transition from the
+	 * BURST_ID to the SYS_E_FLAG register, which will not be equal to 0xA5A5. If
+	 * we not find this variation in the first 4 segments, then the data should
+	 * not be valid.
+	 */
+	buffer = adis->buffer;
+	for (offset = 0; offset < 4; offset++) {
+		u16 curr = be16_to_cpu(buffer[offset]);
+		u16 next = be16_to_cpu(buffer[offset + 1]);
+
+		if (curr == ADIS16495_BURST_ID && next != ADIS16495_BURST_ID) {
+			offset++;
+			break;
+		}
+	}
+
+	if (offset == 4) {
+		dev_err(&adis->spi->dev, "Invalid burst data\n");
+		goto irq_done;
+	}
+
+	crc = be16_to_cpu(buffer[offset + 16]) << 16 | be16_to_cpu(buffer[offset + 15]);
+	valid = adis16480_validate_crc((u16 *)&buffer[offset], 15, crc);
+	if (!valid) {
+		dev_err(&adis->spi->dev, "Invalid crc\n");
+		goto irq_done;
+	}
+
+	for_each_set_bit(bit, indio_dev->active_scan_mask, indio_dev->masklength) {
+		/*
+		 * When burst mode is used, temperature is the first data
+		 * channel in the sequence, but the temperature scan index
+		 * is 10.
+		 */
+		switch (bit) {
+		case ADIS16480_SCAN_TEMP:
+			st->data[i++] = buffer[offset + 1];
+			break;
+		case ADIS16480_SCAN_GYRO_X ... ADIS16480_SCAN_ACCEL_Z:
+			/* The lower register data is sequenced first */
+			st->data[i++] = buffer[2 * bit + offset + 3];
+			st->data[i++] = buffer[2 * bit + offset + 2];
+			break;
+		}
+	}
+
+	iio_push_to_buffers_with_timestamp(indio_dev, st->data, pf->timestamp);
+irq_done:
+	iio_trigger_notify_done(indio_dev->trig);
+
+	return IRQ_HANDLED;
+}
+
 static const struct iio_info adis16480_info = {
 	.read_raw = &adis16480_read_raw,
 	.write_raw = &adis16480_write_raw,
@@ -1341,7 +1474,8 @@ static int adis16480_probe(struct spi_device *spi)
 		st->clk_freq = st->chip_info->int_clk;
 	}
 
-	ret = devm_adis_setup_buffer_and_trigger(&st->adis, indio_dev, NULL);
+	ret = devm_adis_setup_buffer_and_trigger(&st->adis, indio_dev,
+						 adis16480_trigger_handler);
 	if (ret)
 		return ret;
 
author maintainer
#2 lore raw
Quoted 31 lines

-----Original Message-----
From: Jonathan Cameron <[email protected]>
Sent: Saturday, April 24, 2021 1:32 PM
To: Sa, Nuno <[email protected]>
Cc: [email protected]; Hennerich, Michael <[email protected]>; Lars-Peter Clausen <[email protected]>
Subject: Re: [PATCH v4] iio: adis16480: support burst read function

Quoted 1 line · On Thu, 22 Apr 2021 12:37:35 +0200 Nuno Sa <[email protected]> wrote:

Some supported devices support burst read function. This provides a

method

Quoted 2 lines

for reading a batch of data (status, temperature, gyroscopes, accelerometers, time stamp/data counter, and CRC code), which

does not

Quoted 1 line

require a stall time between each 16-bit segment and only requires

one

Quoted 10 lines

command on the DIN line to initiate. Devices supporting this mode are:

* adis16495-1
* adis16495-2
* adis16495-3
* adis16497-1
* adis16497-2
* adis16497-3

Quoted 6 lines
Quoted 2 lines

Looks good to me. Give me a poke if I seem to have lost it when the dependency is in place.

poking :) ...

- Nuno Sá

maintainer
#3 lore raw
Quoted 29 lines · Nuno
Quoted 29 lines

-----Original Message-----
From: Jonathan Cameron <[email protected]>
Sent: Saturday, April 24, 2021 1:32 PM
To: Sa, Nuno <[email protected]>
Cc: [email protected]; Hennerich, Michael <[email protected]>; Lars-Peter Clausen <[email protected]>
Subject: Re: [PATCH v4] iio: adis16480: support burst read function

Quoted 1 line · On Thu, 22 Apr 2021 12:37:35 +0200 Nuno Sa <[email protected]> wrote:

Some supported devices support burst read function. This provides a

method

Quoted 2 lines

for reading a batch of data (status, temperature, gyroscopes, accelerometers, time stamp/data counter, and CRC code), which

does not

Quoted 1 line

require a stall time between each 16-bit segment and only requires

one

Quoted 10 lines

command on the DIN line to initiate. Devices supporting this mode are:

* adis16495-1
* adis16495-2
* adis16495-3
* adis16497-1
* adis16497-2
* adis16497-3

Quoted 8 lines
Quoted 6 lines
Quoted 2 lines

Looks good to me. Give me a poke if I seem to have lost it when the dependency is in place.

poking :) ...

Thanks :)
Applied to the togreg branch of iio.git and pushed out as testing for all the normal reasons.

Jonathan

Quoted 2 lines

- Nuno Sá

author maintainer
#4 lore raw

Hi Jonathan,

Quoted 49 lines

-----Original Message-----
From: Jonathan Cameron <[email protected]>
Sent: Saturday, May 8, 2021 4:57 PM
To: Sa, Nuno <[email protected]>
Cc: [email protected]; Hennerich, Michael <[email protected]>; Lars-Peter Clausen <[email protected]>
Subject: Re: [PATCH v4] iio: adis16480: support burst read function

[External]

Quoted 9 lines · Nuno
Quoted 9 lines

-----Original Message-----
From: Jonathan Cameron <[email protected]>
Sent: Saturday, April 24, 2021 1:32 PM
To: Sa, Nuno <[email protected]>
Cc: [email protected]; Hennerich, Michael <[email protected]>; Lars-Peter Clausen <[email protected]>
Subject: Re: [PATCH v4] iio: adis16480: support burst read function

Quoted 4 lines
Quoted 4 lines
Quoted 1 line · On Thu, 22 Apr 2021 12:37:35 +0200 Nuno Sa <[email protected]> wrote:

Some supported devices support burst read function. This

provides a

Quoted 5 lines
Quoted 5 lines

method

Quoted 2 lines

for reading a batch of data (status, temperature, gyroscopes, accelerometers, time stamp/data counter, and CRC code), which

does not

Quoted 1 line

require a stall time between each 16-bit segment and only

requires

Quoted 2 lines
Quoted 2 lines

one

Quoted 1 line

command on the DIN line to initiate. Devices supporting this

mode

Quoted 12 lines
Quoted 12 lines
Quoted 11 lines

are:

* adis16495-1
* adis16495-2
* adis16495-3
* adis16497-1
* adis16497-2
* adis16497-3

Quoted 9 lines
Quoted 5 lines
Quoted 3 lines

Looks good to me. Give me a poke if I seem to have lost it when the dependency is in place.

poking :) ...

Thanks :)
Applied to the togreg branch of iio.git and pushed out as testing for all the normal reasons.

Was this patch somehow lost? I was trying to sync up ADI internal tree and I cannot see this patch either in testing or togreg...

Thanks,
- Nuno Sá

maintainer
#5 lore raw
Quoted 55 lines · Nuno

Hi Jonathan,

Quoted 53 lines

-----Original Message-----
From: Jonathan Cameron <[email protected]>
Sent: Saturday, May 8, 2021 4:57 PM
To: Sa, Nuno <[email protected]>
Cc: [email protected]; Hennerich, Michael <[email protected]>; Lars-Peter Clausen <[email protected]>
Subject: Re: [PATCH v4] iio: adis16480: support burst read function

[External]

Quoted 9 lines · Nuno
Quoted 9 lines

-----Original Message-----
From: Jonathan Cameron <[email protected]>
Sent: Saturday, April 24, 2021 1:32 PM
To: Sa, Nuno <[email protected]>
Cc: [email protected]; Hennerich, Michael <[email protected]>; Lars-Peter Clausen <[email protected]>
Subject: Re: [PATCH v4] iio: adis16480: support burst read function

Quoted 4 lines
Quoted 4 lines
Quoted 1 line · On Thu, 22 Apr 2021 12:37:35 +0200 Nuno Sa <[email protected]> wrote:

Some supported devices support burst read function. This

provides a

Quoted 5 lines
Quoted 5 lines

method

Quoted 2 lines

for reading a batch of data (status, temperature, gyroscopes, accelerometers, time stamp/data counter, and CRC code), which

does not

Quoted 1 line

require a stall time between each 16-bit segment and only

requires

Quoted 2 lines
Quoted 2 lines

one

Quoted 1 line

command on the DIN line to initiate. Devices supporting this

mode

Quoted 16 lines
Quoted 15 lines
Quoted 11 lines

are:

* adis16495-1
* adis16495-2
* adis16495-3
* adis16497-1
* adis16497-2
* adis16497-3

Looks good to me. Give me a poke if I seem to have lost it when the dependency is in place.

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

poking :) ...

Thanks :)
Applied to the togreg branch of iio.git and pushed out as testing for all the normal reasons.

Was this patch somehow lost? I was trying to sync up ADI internal tree and I cannot see this patch either in testing or togreg...

Odd. Sorry about that. Now applied and pushed out as testing.

Jonathan

Quoted 3 lines

Thanks,
- Nuno Sá