imx: mkimage_fit_atf: replace @ with hyphen
Subsystems (3)
PATCH 1/1 imx: mkimage_fit_atf: replace @ with hyphen
Unit addresses are not allowed anymore in a FIT image since
commit 3f04db891a35 ("image: Check for unit addresses in FITs")
This caused this error on mkimage creation:
./tools/mkimage: verify_header failed for FIT Image support with exit code 1 Makefile:1393: recipe for target 'u-boot.itb' failed
make: *** [u-boot.itb] Error 1
replacing @ with hyphen solved the issue
--- arch/arm/mach-imx/mkimage_fit_atf.sh | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-)
arch/arm/mach-imx/mkimage_fit_atf.sh +12 -12
@@ -53,7 +53,7 @@ cat << __HEADER_EOF description = "Configuration to load ATF before U-Boot"; images { - uboot at 1 { + uboot-1 { description = "U-Boot (64-bit)"; os = "u-boot"; data = /incbin/("$BL33");
@@ -68,7 +68,7 @@ cnt=1 for dtname in $* do cat << __FDT_IMAGE_EOF - fdt@$cnt { + fdt-$cnt { description = "$(basename $dtname .dtb)"; data = /incbin/("$dtname"); type = "flat_dt";
@@ -79,7 +79,7 @@ cnt=$((cnt+1)) done cat << __HEADER_EOF - atf at 1 { + atf-1 { description = "ARM Trusted Firmware"; os = "arm-trusted-firmware"; data = /incbin/("$BL31");
@@ -93,7 +93,7 @@ __HEADER_EOF if [ -f $BL32 ]; then cat << __HEADER_EOF - tee at 1 { + tee-1 { description = "TEE firmware"; data = /incbin/("$BL32"); type = "firmware";
@@ -108,7 +108,7 @@ fi cat << __CONF_HEADER_EOF }; configurations { - default = "config at 1"; + default = "config-1"; __CONF_HEADER_EOF
@@ -117,20 +117,20 @@ for dtname in $* do if [ -f $BL32 ]; then cat << __CONF_SECTION_EOF - config@$cnt { + config-$cnt { description = "$(basename $dtname .dtb)"; - firmware = "uboot at 1"; - loadables = "atf at 1", "tee at 1"; + firmware = "uboot-1"; + loadables = "atf-1", "tee-1"; fdt = "fdt@$cnt"; }; __CONF_SECTION_EOF else cat << __CONF_SECTION1_EOF - config@$cnt { + config-$cnt { description = "$(basename $dtname .dtb)"; - firmware = "uboot at 1"; - loadables = "atf@1"; - fdt = "fdt@$cnt"; + firmware = "uboot-1"; + loadables = "atf-1"; + fdt = "fdt-$cnt"; }; __CONF_SECTION1_EOF fi
Signature · 1 line
2.17.1
PATCH 1/1 imx: mkimage_fit_atf: replace @ with hyphen
Hello Oliver,
Quoted 12 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Oliver Graute
Sent: Wednesday, May 5, 2021 2:01 PM
To: sbabic at denx.de
Cc: festevam at gmail.com; peng.fan at nxp.com; oliver.graute at kococonnector.com; u-boot at lists.denx.de; Simon Glass <[email protected]>; uboot-imx <[email protected]>
Subject: [PATCH v1] imx:mkimage_fit_atf: replace @ with hyphenUnit addresses are not allowed anymore in a FIT image since
Quoted 7 lines
commit
3f04db891a35("image: Check for unit addresses in FITs")This caused this error on mkimage creation:
./tools/mkimage:verify_headerfailed for FIT Image support with exit code 1 Makefile:1393: recipe for target 'u-boot.itb' failed
make: *** [u-boot.itb] Error 1
IIRC, this error comes from the derivatives which are not (yet) migrated to use 'binman' and have CONFIG_SPL_FIT_GENERATOR set.
It is triggered by 79af75f777 ("fit: Don't allow verification of images with @ nodes"), which is totally correct behavior and should be corrected on the FIT generator end, so the patch itself solves the problem.
TBH, I had introduced the same change to NXP U-Boot fork that is built for NXP Yocto BSP [1], and was not sure it is relevant for the master since it uses 'binman' instead of FIT generator.
From the other point of view, which imx8m board do you experience this build problem with?
Currently, there are following boards that need to be migrated from FIT generator to 'binman':
configs/imx8mm_beacon_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/imx8mm_venice_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/imx8mn_beacon_2g_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/imx8mn_beacon_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/imx8mq_evk_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/imx8mq_phanbell_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/imx8qm_rom7720_a1_4G_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/phycore-imx8mm_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/phycore-imx8mp_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/pico-imx8mq_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" configs/verdin-imx8mm_defconfig:CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
I know it's a long shot, but the question is: should the FIT generator be adapted here, or maybe those boards that are still using it - to be migrated to binman directly?
There is already a warning in root Makefile regarding usage of FIT generator:
"===================== WARNING ======================"
"This board uses CONFIG_SPL_FIT_GENERATOR. Please migrate"
"to binman instead, to avoid the proliferation of"
"arch-specific scripts with no tests." "===================================================="
So maybe it makes sense to adapt affected boards instead?
Quoted 86 lines
replacing @ with hyphen solved the issue
Signed-off-by Oliver Graute <[email protected]>Cc Stefano Babic <[email protected]>Cc Fabio Estevam <[email protected]>Cc Peng Fan <[email protected]>Cc Simon Glass <[email protected]>Cc uboot-imx <[email protected]>--- arch/arm/mach-imx/mkimage_fit_atf.sh | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-)arch/arm/mach- renamed from arch/arm/mach-imx/mkimage_fit_atf.sh +0
-0
imx/mkimage_fit_atf.sh
indexfe12b7bb4b..c5fb9b0fc3100755arch/arm/mach-imx/mkimage_fit_atf.sh +1
-1@@ -53,7 +53,7 @@ cat << __HEADER_EOF description = "Configuration to load ATF before U-Boot"; images { - uboot at 1 { + uboot-1 { description = "U-Boot (64-bit)"; os = "u-boot"; data = /incbin/("$BL33"); @@ -68,7 +68,7 @@ cnt=1 for dtname in $*do
cat << __FDT_IMAGE_EOFarch/arm/mach-imx/mkimage_fit_atf.sh +3
-3- fdt@$cnt { + fdt-$cnt { description = "$(basename $dtname .dtb)"; data = /incbin/("$dtname"); type = "flat_dt"; @@ -79,7 +79,7 @@ cnt=$((cnt+1)) done cat << __HEADER_EOF - atf at 1 { + atf-1 { description = "ARM Trusted Firmware"; os = "arm-trusted-firmware"; data = /incbin/("$BL31"); @@ -93,7 +93,7 @@ __HEADER_EOF if [ -f $BL32 ]; then cat << __HEADER_EOF - tee at 1 { + tee-1 { description = "TEE firmware"; data = /incbin/("$BL32"); type = "firmware"; @@ -108,7 +108,7 @@ fi cat <<
__CONF_HEADER_EOF}; configurations {arch/arm/mach-imx/mkimage_fit_atf.sh +8
-9- default = "config at 1"; + default = "config-1"; __CONF_HEADER_EOF@@ -117,20 +117,20 @@ for dtname in $* do if [ -f $BL32 ]; then cat << __CONF_SECTION_EOF - config@$cnt { + config-$cnt { description = "$(basename $dtname .dtb)"; - firmware = "uboot at 1"; - loadables = "atf at 1", "tee at 1"; + firmware = "uboot-1"; + loadables = "atf-1", "tee-1"; fdt = "fdt@$cnt"; }; __CONF_SECTION_EOF else cat << __CONF_SECTION1_EOF - config@$cnt { + config-$cnt { description = "$(basename $dtname .dtb)"; - firmware = "uboot at 1"; - loadables = "atf at 1"; - fdt = "fdt@$cnt"; + firmware = "uboot-1"; + loadables = "atf-1"; + fdt = "fdt-$cnt"; }; __CONF_SECTION1_EOF fi --
Quoted 1 line
2.17.1
-- andrey
Hi all,
Am Mi., 5. Mai 2021 um 15:30 Uhr schrieb ZHIZHIKIN Andrey <[email protected]>:
Quoted 22 lines
Hello Oliver,
Quoted 19 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Oliver Graute
Sent: Wednesday, May 5, 2021 2:01 PM
To: [email protected]
Cc: [email protected]; [email protected]; [email protected]; [email protected]; Simon Glass <[email protected]>; uboot-imx <[email protected]>
Subject: [PATCH v1] imx:mkimage_fit_atf: replace @ with hyphenUnit addresses are not allowed anymore in a FIT image since
commit
3f04db891a35("image: Check for unit addresses in FITs")This caused this error on mkimage creation:
./tools/mkimage:verify_headerfailed for FIT Image support with exit code 1 Makefile:1393: recipe for target 'u-boot.itb' failed
make: *** [u-boot.itb] Error 1
This error is still present in the current master branch and the target "flash.bin" does not not build anymore for the imx8mq_evk_defconfig.
Any thoughts to apply this patch to master?
--
Heiko
Quoted 28 lines · Heiko Thiery
Hi all,
Am Mi., 5. Mai 2021 um 15:30 Uhr schrieb ZHIZHIKIN Andrey <[email protected]>:
Quoted 22 lines
Hello Oliver,
Quoted 19 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Oliver Graute
Sent: Wednesday, May 5, 2021 2:01 PM
To: [email protected]
Cc: [email protected]; [email protected]; [email protected]; [email protected]; Simon Glass <[email protected]>; uboot-imx <[email protected]>
Subject: [PATCH v1] imx:mkimage_fit_atf: replace @ with hyphenUnit addresses are not allowed anymore in a FIT image since
commit
3f04db891a35("image: Check for unit addresses in FITs")This caused this error on mkimage creation:
./tools/mkimage:verify_headerfailed for FIT Image support with exit code 1 Makefile:1393: recipe for target 'u-boot.itb' failed
make: *** [u-boot.itb] Error 1
Quoted 6 lines
This error is still present in the current master branch and the target "flash.bin" does not not build anymore for the
imx8mq_evk_defconfig.Any thoughts to apply this patch to master?
Heiko,
I just ran into this failure as well with imx8mm_venice_defconfig which I haven't moved to binman yet.
With respect to moving to binman, I'm all for it but I'm wondering why other boards have elected to move from a monolithic flash.bin including the SPL and u-boot.itb pre-binman to post-binman where flash.bin is just the SPL. I'm not sure why users should be hit with a change like that... why are people not having binman produce a flash.bin that was equivalent to pre-binman?
Best regards,
Tim
Hi Tim,
Quoted 43 lines
Subject: Re: [PATCH v1] imx:
mkimage_fit_atf: replace @ with hyphenQuoted 30 lines · Heiko Thiery
Hi all,
Am Mi., 5. Mai 2021 um 15:30 Uhr schrieb ZHIZHIKIN Andrey <[email protected]>:
Quoted 24 lines
Hello Oliver,
Quoted 21 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Oliver Graute
Sent: Wednesday, May 5, 2021 2:01 PM
To: [email protected]
Cc: [email protected]; [email protected]; [email protected]; [email protected]; Simon Glass <[email protected]>; uboot-imx <[email protected]>
Subject: [PATCH v1] imx:mkimage_fit_atf: replace @ with hyphenUnit addresses are not allowed anymore in a FIT image since
commit
3f04db891a35("image: Check for unit addresses in FITs")This caused this error on mkimage creation:
./tools/mkimage:verify_headerfailed for FIT Image support with exit code 1
Makefile:1393: recipe for target 'u-boot.itb' failed
make: *** [u-boot.itb] Error 1Quoted 6 lines
This error is still present in the current master branch and the target "flash.bin" does not not build anymore for the
imx8mq_evk_defconfig.Any thoughts to apply this patch to master?
Heiko,
Quoted 8 lines
I just ran into this failure as well with
imx8mm_venice_defconfigwhich I haven't moved to binman yet.With respect to moving to binman, I'm all for it but I'm wondering why other boards have elected to move from a monolithic flash.bin including the SPL and u-boot.itb pre-binman to post-binman where flash.bin is just the SPL. I'm not sure why users should be hit with a change like that... why are people not having binman produce a flash.bin that was equivalent to pre-binman?
You mean flash.bin not contain u-boot.bin when using binman here?
Regards,
Peng.
Quoted 4 lines
Best regards,
Tim
Hi all,
Am Mo., 2. Aug. 2021 um 11:57 Uhr schrieb Peng Fan (OSS) <[email protected]>:
Quoted 49 lines
Hi Tim,
Quoted 46 lines
Subject: Re: [PATCH v1] imx:
mkimage_fit_atf: replace @ with hyphenQuoted 30 lines · Heiko Thiery
Hi all,
Am Mi., 5. Mai 2021 um 15:30 Uhr schrieb ZHIZHIKIN Andrey <[email protected]>:
Quoted 24 lines
Hello Oliver,
Quoted 21 lines
-----Original Message-----
From: U-Boot <[email protected]> On Behalf Of Oliver Graute
Sent: Wednesday, May 5, 2021 2:01 PM
To: [email protected]
Cc: [email protected]; [email protected]; [email protected]; [email protected]; Simon Glass <[email protected]>; uboot-imx <[email protected]>
Subject: [PATCH v1] imx:mkimage_fit_atf: replace @ with hyphenUnit addresses are not allowed anymore in a FIT image since
commit
3f04db891a35("image: Check for unit addresses in FITs")This caused this error on mkimage creation:
./tools/mkimage:verify_headerfailed for FIT Image support with exit code 1
Makefile:1393: recipe for target 'u-boot.itb' failed
make: *** [u-boot.itb] Error 1Quoted 6 lines
This error is still present in the current master branch and the target "flash.bin" does not not build anymore for the
imx8mq_evk_defconfig.Any thoughts to apply this patch to master?
Heiko,
I just ran into this failure as well with
imx8mm_venice_defconfigwhich I haven't moved to binman yet.
Quoted 7 lines
Quoted 5 lines
With respect to moving to binman, I'm all for it but I'm wondering why other boards have elected to move from a monolithic flash.bin including the SPL and u-boot.itb pre-binman to post-binman where flash.bin is just the SPL. I'm not sure why users should be hit with a change like that... why are people not having binman produce a flash.bin that was equivalent to pre-binman?
You mean flash.bin not contain u-boot.bin when using binman here?
Any news on that? I just see that in the current master it is not possible to create a working flash.bin for e.g. the imx8mq_evk board.
Signature · 1 line
Heiko
Fabio Estevam
reviewerHi Tim,
[Adding Marek]
Quoted 6 lines · Tim Harvey
With respect to moving to binman, I'm all for it but I'm wondering why other boards have elected to move from a monolithic flash.bin including the SPL and u-boot.itb pre-binman to post-binman where flash.bin is just the SPL. I'm not sure why users should be hit with a change like that... why are people not having binman produce a flash.bin that was equivalent to pre-binman?
Yes, fully agree.
Peng,
After the adoption of binman, both flash.bin and u-boot.itb need to be flashed to the boot media.
This breaks user experience, distro integration, etc, which is not good.
Can we have binman generate a single bootable flash.bin binary (which contains flash.bin + u-boot.itb) again
to keep compatibility and avoid breakage?
Thanks,
Fabio Estevam
Quoted 4 lines
Best regards,
Tim
Hi,
Am Fr., 13. Aug. 2021 um 14:34 Uhr schrieb Fabio Estevam <[email protected]>:
Quoted 18 lines
Hi Tim,
[Adding Marek]
Quoted 6 lines · Tim Harvey
With respect to moving to binman, I'm all for it but I'm wondering why other boards have elected to move from a monolithic flash.bin including the SPL and u-boot.itb pre-binman to post-binman where flash.bin is just the SPL. I'm not sure why users should be hit with a change like that... why are people not having binman produce a flash.bin that was equivalent to pre-binman?
Yes, fully agree.
Peng,
Quoted 8 lines
After the adoption of binman, both flash.bin and u-boot.itb need to be flashed to the boot media.
This breaks user experience, distro integration, etc, which is not good.
Can we have binman generate a single bootable flash.bin binary (which contains flash.bin + u-boot.itb) again
to keep compatibility and avoid breakage?
Maybe I'm wrong or I do not fully understand the limitation you're talking about, but as far as I understand the output (flash.bin) from the ronetix board [1] was generated using binman and includes all necessary parts. Is this right?
[1] https://source.denx.de/u-boot/u-boot/-/blob/master/arch/arm/dts/imx8mq-cm-u-boot.dtsi
Signature · 1 line
Heiko
Fabio Estevam
reviewerHi Heiko,
Quoted 4 lines · Heiko Thiery
Maybe I'm wrong or I do not fully understand the limitation you're talking about, but as far as I understand the output (flash.bin) from the ronetix board [1] was generated using binman and includes all necessary parts. Is this right?
Building the imx8mq_cm_defconfig generates flash.bin + u-boot.itb.
If you only flash flash.bin, then you don't have a bootable system as flash.bin contains only the SPL part.
Prior to using binman, we could boot the i.MX8M boards by flashing only flash.bin.
I would like to preserver the pre-U-Boot 2021.07, where only flash.bin was needed.
Quoted 6 lines
[1] https://source.denx.de/u-boot/u-boot/-/blob/master/arch/arm/dts/imx8mq-cm-u-boot.dtsi
--
Heiko
Hi Fabio,
Am Fr., 13. Aug. 2021 um 15:03 Uhr schrieb Fabio Estevam <[email protected]>:
Quoted 12 lines
Hi Heiko,
Quoted 4 lines · Heiko Thiery
Maybe I'm wrong or I do not fully understand the limitation you're talking about, but as far as I understand the output (flash.bin) from the ronetix board [1] was generated using binman and includes all necessary parts. Is this right?
Building the
imx8mq_cm_defconfiggenerates flash.bin + u-boot.itb.
Quoted 8 lines
If you only flash flash.bin, then you don't have a bootable system as flash.bin contains only the SPL part.
Prior to using binman, we could boot the i.MX8M boards by flashing only flash.bin.
I would like to preserver the pre-U-Boot 2021.07, where only flash.bin was needed.
I had taken the binman configuration from imx8mq_cm_defconfig and adapted it for my board (kontron-pitx-imx8m). I had copied the flash.bin image to my SD card and am of the opinion that this had started afterwards with the current u-boot. Unfortunately I can test it only next week again, because I currently have no device at hand.
I must confess that I do not yet fully understand how binman works.
I'll get back to you next week.
Signature · 1 line
Heiko
HI Fabrio and all,
Am Fr., 13. Aug. 2021 um 17:12 Uhr schrieb Heiko Thiery <[email protected]>:
Quoted 22 lines
Hi Fabio,
Am Fr., 13. Aug. 2021 um 15:03 Uhr schrieb Fabio Estevam <[email protected]>:
Quoted 18 lines
Hi Heiko,
Quoted 4 lines · Heiko Thiery
Maybe I'm wrong or I do not fully understand the limitation you're talking about, but as far as I understand the output (flash.bin) from the ronetix board [1] was generated using binman and includes all necessary parts. Is this right?
Building the
imx8mq_cm_defconfiggenerates flash.bin + u-boot.itb.If you only flash flash.bin, then you don't have a bootable system as flash.bin contains only the SPL part.
Prior to using binman, we could boot the i.MX8M boards by flashing only flash.bin.
Quoted 8 lines
Quoted 2 lines
I would like to preserver the pre-U-Boot 2021.07, where only flash.bin was needed.
I had taken the binman configuration from
imx8mq_cm_defconfigand adapted it for my board (kontron-pitx-imx8m). I had copied the flash.bin image to my SD card and am of the opinion that this had started afterwards with the current u-boot. Unfortunately I can test it only next week again, because I currently have no device at hand.
You were right. I probably still had the old data from u-boot.itb on the SD card and therefore the board still started correctly.
But I also think that the flash.bin should have the complete content (spl + u-boot.itb) so that the board starts correctly.
Sorry for the noise.
Signature · 1 line
Heiko