Skip to contentSkip to conversation

mx8mm: usb: chipidea: Fix Battery Charger 1.2 CDP detection

PATCH Superseded Breno Lima 3 participants 3 messages Jun 11, 2021 – Jun 12, 2021

Subsystems (3)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Breno Lima

author
#0 lore raw

PATCH v2 1/1 mx8mm: usb: chipidea: Fix Battery Charger 1.2 CDP detection

i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not following CDP timing requirements defined by USB BC 1.2 specification and section 3.2.4 Detection Timing CDP.

During Primary Detection the i.MX device should turn on VDP_SRC and IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON, the PD is allowed to check the status of the D- line. Current implementation is waiting between 1ms and 2ms, and certain BC 1.2 complaint USB HUBs cannot be detected. Increase delay to 40ms allowing enough time for primary detection.

During secondary detection the PD is required to disable VDP_SRC and IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).

Current implementation is not disabling VDP_SRC and IDM_SNK, introduce disable sequence in imx7d_charger_secondary_detection() function.

VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON). Increase delay allowing enough time for detection.

Fixes 746f316b753a ("usb: chipidea: introduce imx7d USB charger detection")

---
Changes since V1:
- Updated commit log to include commit ID fix

 drivers/usb/chipidea/usbmisc_imx.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)
drivers/usb/chipidea/usbmisc_imx.c +14 -2
index 4545b23bda3f..bac0f5458cab 100644
@@ -686,6 +686,16 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
 	int val;
 	unsigned long flags;
 
+	/* Clear VDATSRCENB0 to disable VDP_SRC and IDM_SNK required by BC 1.2 spec */
+	spin_lock_irqsave(&usbmisc->lock, flags);
+	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
+	val &= ~MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0;
+	writel(val, usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
+	spin_unlock_irqrestore(&usbmisc->lock, flags);
+
+	/* TVDMSRC_DIS */
+	msleep(20);
+
 	/* VDM_SRC is connected to D- and IDP_SINK is connected to D+ */
 	spin_lock_irqsave(&usbmisc->lock, flags);
 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
@@ -695,7 +705,8 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
-	usleep_range(1000, 2000);
+	/* TVDMSRC_ON */
+	msleep(40);
 
 	/*
 	 * Per BC 1.2, check voltage of D+:
@@ -798,7 +809,8 @@ static int imx7d_charger_primary_detection(struct imx_usbmisc_data *data)
 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
-	usleep_range(1000, 2000);
+	/* TVDPSRC_ON */
+	msleep(40);
 
 	/* Check if D- is less than VDAT_REF to determine an SDP per BC 1.2 */
 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_STATUS);
Signature · 1 line
2.25.1
maintainer
#1 lore raw
Quoted 4 lines · Breno Lima

i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not following CDP timing requirements defined by USB BC 1.2 specification and section 3.2.4 Detection Timing CDP.

Quoted 8 lines

During Primary Detection the i.MX device should turn on VDP_SRC and IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON, the PD is allowed to check the status of the D- line. Current implementation is waiting between 1ms and 2ms, and certain BC 1.2 complaint USB HUBs cannot be detected. Increase delay to 40ms allowing enough time for primary detection.

During secondary detection the PD is required to disable VDP_SRC and

What does the "PD" mean here?

Quoted 9 lines

IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).

Current implementation is not disabling VDP_SRC and IDM_SNK, introduce disable sequence in imx7d_charger_secondary_detection() function.

VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON). Increase delay allowing enough time for detection.

Fixes 746f316b753a ("usb: chipidea: introduce imx7d USB charger detection")

I assume this one needs to go stable tree?

Peter

Quoted 53 lines

---
Changes since V1:
- Updated commit log to include commit ID fix

 drivers/usb/chipidea/usbmisc_imx.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)
drivers/usb/chipidea/usbmisc_imx.c +14 -2
index 4545b23bda3f..bac0f5458cab 100644
@@ -686,6 +686,16 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
 	int val;
 	unsigned long flags;
 
+	/* Clear VDATSRCENB0 to disable VDP_SRC and IDM_SNK required by BC 1.2 spec */
+	spin_lock_irqsave(&usbmisc->lock, flags);
+	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
+	val &= ~MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0;
+	writel(val, usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
+	spin_unlock_irqrestore(&usbmisc->lock, flags);
+
+	/* TVDMSRC_DIS */
+	msleep(20);
+
 	/* VDM_SRC is connected to D- and IDP_SINK is connected to D+ */
 	spin_lock_irqsave(&usbmisc->lock, flags);
 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
@@ -695,7 +705,8 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
-	usleep_range(1000, 2000);
+	/* TVDMSRC_ON */
+	msleep(40);
 
 	/*
 	 * Per BC 1.2, check voltage of D+:
@@ -798,7 +809,8 @@ static int imx7d_charger_primary_detection(struct imx_usbmisc_data *data)
 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
-	usleep_range(1000, 2000);
+	/* TVDPSRC_ON */
+	msleep(40);
 
 	/* Check if D- is less than VDAT_REF to determine an SDP per BC 1.2 */
 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_STATUS);
Signature · 1 line
2.25.1
Signature · 2 lines
Thanks,
Peter Chen
#2 lore raw

Hi Peter,

Em sáb., 12 de jun. de 2021 às 03:24, Peter Chen
<[email protected]> escreveu:

Quoted 13 lines · Breno Lima
Quoted 11 lines

i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not following CDP timing requirements defined by USB BC 1.2 specification and section 3.2.4 Detection Timing CDP.

During Primary Detection the i.MX device should turn on VDP_SRC and IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON, the PD is allowed to check the status of the D- line. Current implementation is waiting between 1ms and 2ms, and certain BC 1.2 complaint USB HUBs cannot be detected. Increase delay to 40ms allowing enough time for primary detection.

Quoted 4 lines
Quoted 1 line

During secondary detection the PD is required to disable VDP_SRC and

What does the "PD" mean here?

PD stands for Portable Device, I can send another version and mention i.MX instead.

Thanks for pointing this out.

Best regards,
Breno Lima