PCI/PM: Target PM state is D3hot if device can only generate PME from D3cold
PATCH v3 1/1 PCI/PM: Target PM state is D3hot if device can only generate PME from D3cold
Some PCIe devices only support PME (Power Management Event) from D3cold. One example is ASMedia xHCI controller:
11:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller (prog-if 30 [XHCI])
...
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
With such devices, if it has wake enabled, the kernel selects lowest possible power state to be D0 in pci_target_state(). This is problematic because it prevents the root port it is connected to enter low power state too which makes the system consume more energy than necessary.
The problem in pci_target_state() is that it only accounts the "current" device state, so when the bridge above it (a root port for instance) is transitioned into D3hot the device transitions into D3cold. This is because when the root port is first transitioned into D3hot then the ACPI power resource is turned off which puts the PCIe link to L2/L3 (and the root port and the device are in D3cold). If the root port is kept in D3hot it still means that the device below it is still effectively in D3cold as no configuration messages pass through. Furthermore the implementation note of PCIe 5.0 sec 5.3.1.4 says that the device should expect to be transitioned into D3cold soon after its link transitions into L2/L3 Ready state.
Taking the above into consideration, instead of forcing the device stay in D0 we modify pci_target_state() to return D3hot in this special case and make __pci_enable_wake() to enable PME too in this case.
---
Hi all,
This is third version of the patch. I changed this according to what Rafael suggested, so that the pci_target_state() returns D3hot for these devices and pci_enable_wake() then enables PME from D3cold. This solves the problem in my test system.
@Utkarsh, @Koba, I appreciate if you could try this one too.
I also dropped the Tested-by tag from Koba Ko and Acked-by from Kai-Heng Feng as this is not the same patch anymore.
The previous version can be seen here:
https://lore.kernel.org/linux-pci/[email protected]/
drivers/pci/pci.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
drivers/pci/pci.c +17 -1
@@ -2485,7 +2485,13 @@ static int __pci_enable_wake(struct pci_dev *dev, pci_power_t state, bool enableif (enable) {int error; -if (pci_pme_capable (dev, state)) +/* +* Enable PME if device is capable from given state. +* Special case is device that can only generate PME +* from D3cold then we enable PME too. +*/ +if (pci_pme_capable (dev, state) || + (state == PCI_D3hot &&pci_pme_capable (dev, PCI_D3cold)))pci_pme_active (dev, true);else ret =1 ;
@@ -2595,6 +2601,16 @@ static pci_power_t pci_target_state(struct pci_dev *dev, bool wakeup)* PME#. */ if (dev->pme_support) { +/* +* Special case if device supports only PME from +* D3cold but not from D3hot we still return +* D3hot. +*/ +if (target_state == PCI_D3hot && + !(dev->pme_support & (1 << PCI_D3hot)) && + (dev->pme_support & (1 << PCI_D3cold))) +return target_state; +while (target_state && !(dev->pme_support & (1 << target_state))) target_state--;
Signature · 1 line
2.30.2
Quoted 26 lines · CEST Mika Westerberg
Some PCIe devices only support PME (Power Management Event) from D3cold. One example is ASMedia xHCI controller:
11:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller (prog-if 30 [XHCI])
...
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mAPME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-With such devices, if it has wake enabled, the kernel selects lowest possible power state to be D0 in
pci_target_state(). This is problematic because it prevents the root port it is connected to enter low power state too which makes the system consume more energy than necessary.The problem in
pci_target_state()is that it only accounts the "current" device state, so when the bridge above it (a root port for instance) is transitioned into D3hot the device transitions into D3cold. This is because when the root port is first transitioned into D3hot then the ACPI power resource is turned off which puts the PCIe link to L2/L3 (and the root port and the device are in D3cold). If the root port is kept in D3hot it still means that the device below it is still effectively in D3cold as no configuration messages pass through. Furthermore the implementation note of PCIe 5.0 sec 5.3.1.4 says that the device should expect to be transitioned into D3cold soon after its link transitions into L2/L3 Ready state.
Quoted 8 lines
Taking the above into consideration, instead of forcing the device stay in D0 we modify
pci_target_state()to return D3hot in this special case and make__pci_enable_wake()to enable PME too in this case.Reported-by Utkarsh H Patel <[email protected]>Reported-by Koba Ko <[email protected]>Suggested-by Rafael J. Wysocki <[email protected]>Signed-off-by Mika Westerberg <[email protected]>
Any chance to resend with a CC to linux-pm?
Quoted 57 lines
---
Hi all,This is third version of the patch. I changed this according to what Rafael suggested, so that the
pci_target_state()returns D3hot for these devices andpci_enable_wake()then enables PME from D3cold. This solves the problem in my test system.@Utkarsh, @Koba, I appreciate if you could try this one too.
I also dropped the Tested-by tag from Koba Ko and Acked-by from Kai-Heng Feng as this is not the same patch anymore.
The previous version can be seen here:
https://lore.kernel.org/linux-pci/[email protected]/
drivers/pci/pci.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)drivers/pci/pci.c +17
-1@@ -2485,7 +2485,13 @@ static int __pci_enable_wake(struct pci_dev *dev, pci_power_t state, bool enableif (enable) {int error; -if (pci_pme_capable (dev, state)) +/* +* Enable PME if device is capable from given state. +* Special case is device that can only generate PME +* from D3cold then we enable PME too. +*/ +if (pci_pme_capable (dev, state) || + (state == PCI_D3hot &&pci_pme_capable (dev, PCI_D3cold)))pci_pme_active (dev, true);else ret =1 ;@@ -2595,6 +2601,16 @@ static pci_power_t pci_target_state(struct pci_dev *dev, bool wakeup)* PME#. */ if (dev->pme_support) { +/* +* Special case if device supports only PME from +* D3cold but not from D3hot we still return +* D3hot. +*/ +if (target_state == PCI_D3hot && + !(dev->pme_support & (1 << PCI_D3hot)) && + (dev->pme_support & (1 << PCI_D3cold))) +return target_state; +while (target_state && !(dev->pme_support & (1 << target_state))) target_state--;