remove the legacy ide driver v2
Subsystems (6)
Hi all,
we've been trying to get rid of the legacy ide driver for a while now, and finally scheduled a removal for 2021, which is three month old now.
In general distros and most defconfigs have switched to libata long ago, but there are a few exceptions. This series first switches over all remaining defconfigs to use libata and then removes the legacy ide driver.
libata mostly covers all hardware supported by the legacy ide driver. There are three mips drivers that are not supported, but the linux-mips list could not identify any users of those. There also are two m68k drivers that do not have libata equivalents, which might or might not have users, so we'll need some input and possibly help from the m68k community here.
This series is against Jens' for-5.14/libata branch.
Changes since v1:
- dropped various already merged patches
- add a new module option to allow disabling DMA just for the quirky cypress devices found on some stone age ARM and Alpha systems
PATCH 1/6 pata_cypress: add a module option to disable BM-DMA
Multiple users report that they need to disable DMA on this driver, so provide an option to do so without affecting all of libata.
--- drivers/ata/pata_cypress.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)
drivers/ata/pata_cypress.c +8 -2
@@ -41,6 +41,10 @@ enum { CY82_INDEX_TIMEOUT = 0x32 }; +static bool enable_dma = true; +module_param (enable_dma, bool,0 ); +MODULE_PARM_DESC (enable_dma,"Enable bus master DMA operations" ); +/** * cy82c693_set_piomode - set initial PIO mode data * @ap: ATA interface
@@ -124,14 +128,16 @@ static struct ata_port_operations cy82c693_port_ops = {static int cy82c693_init_one (struct pci_dev *pdev,const struct pci_device_id *id) { -static const struct ata_port_info info = { +static struct ata_port_info info = { .flags =ATA_FLAG_SLAVE_POSS , .pio_mask =ATA_PIO4 , - .mwdma_mask =ATA_MWDMA2 , .port_ops = &cy82c693_port_ops };const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info }; +if (enable_dma) + info.mwdma_mask =ATA_MWDMA2 ; +/* Devfn 1 is the ATA primary. The secondary is magic and on devfn2. For the moment we don't handle the secondary. FIXME */
Signature · 1 line
2.30.2
Re: [PATCH 1/6] pata_cypress: add a module option to disable BM-DMA
Quoted 4 lines · Christoph Hellwig
Multiple users report that they need to disable DMA on this driver, so provide an option to do so without affecting all of libata.
Signed-off-by Christoph Hellwig <[email protected]>
Thanks!
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
PATCH 2/6 alpha: use libata instead of the legacy ide driver
In reply to Christoph HellwigSwitch the alpha defconfig from the legacy ide driver to libata.
--- arch/alpha/configs/defconfig | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-)
arch/alpha/configs/defconfig +6 -7
@@ -25,19 +25,18 @@ CONFIG_PNP=y CONFIG_ISAPNP=y CONFIG_BLK_DEV_FD=y CONFIG_BLK_DEV_LOOP=m -CONFIG_IDE=y -CONFIG_BLK_DEV_IDECD=y -CONFIG_IDE_GENERIC=y -CONFIG_BLK_DEV_GENERIC=y -CONFIG_BLK_DEV_ALI15X3=y -CONFIG_BLK_DEV_CMD64X=y -CONFIG_BLK_DEV_CY82C693=y CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_BLK_DEV_SR=y CONFIG_SCSI_AIC7XXX=m CONFIG_AIC7XXX_CMDS_PER_DEVICE=253 # CONFIG_AIC7XXX_DEBUG_ENABLE is not set +CONFIG_ATA=y +# CONFIG_SATA_PMP is not set +CONFIG_PATA_ALI=y +CONFIG_PATA_CMD64X=y +CONFIG_PATA_CYPRESS=y +CONFIG_ATA_GENERIC=y CONFIG_NETDEVICES=y CONFIG_DUMMY=m CONFIG_NET_ETHERNET=y
Signature · 1 line
2.30.2
PATCH 3/6 ARM: disable CONFIG_IDE in footbridge_defconfig
In reply to Christoph Hellwigfootbridge_defconfig enables CONFIG_IDE but no actual host controller driver, so just drop it.
--- arch/arm/configs/footbridge_defconfig | 1 - 1 file changed, 1 deletion(-)
arch/arm/configs/footbridge_defconfig +0 -1
@@ -64,7 +64,6 @@ CONFIG_PARIDE_ON26=m CONFIG_BLK_DEV_LOOP=m CONFIG_BLK_DEV_NBD=m CONFIG_BLK_DEV_RAM=y -CONFIG_IDE=y CONFIG_NETDEVICES=y CONFIG_NET_ETHERNET=y CONFIG_NET_VENDOR_3COM=y
Signature · 1 line
2.30.2
PATCH 4/6 ARM: disable CONFIG_IDE in pxa_defconfig
In reply to Christoph Hellwigpxa_defconfig already enables libata including the pata_pcmcia driver, so drop the legacy ide driver and idecs host driver.
--- arch/arm/configs/pxa_defconfig | 2 -- 1 file changed, 2 deletions(-)
arch/arm/configs/pxa_defconfig +0 -2
@@ -215,8 +215,6 @@ CONFIG_IIO=m CONFIG_AD5446=m CONFIG_EEPROM_AT24=m CONFIG_SENSORS_LIS3_SPI=m -CONFIG_IDE=m -CONFIG_BLK_DEV_IDECS=m CONFIG_SCSI=y CONFIG_BLK_DEV_SD=m CONFIG_CHR_DEV_ST=m
Signature · 1 line
2.30.2
PATCH 5/6 m68k: use libata instead of the legacy ide driver
In reply to Christoph HellwigSwitch the m68 defconfigs from the deprecated ide subsystem to use libata instead. The gayle and buddha and falcon drivers are enabled for libata, while support for the q40 and macide drivers is lost.
--- arch/m68k/configs/amiga_defconfig | 10 +++++----- arch/m68k/configs/atari_defconfig | 8 ++++---- arch/m68k/configs/mac_defconfig | 8 ++++---- arch/m68k/configs/multi_defconfig | 14 +++++++------- arch/m68k/configs/q40_defconfig | 8 ++++---- 5 files changed, 24 insertions(+), 24 deletions(-)
arch/m68k/configs/amiga_defconfig +5 -5
@@ -323,11 +323,6 @@ CONFIG_BLK_DEV_RAM=y CONFIG_CDROM_PKTCDVD=m CONFIG_ATA_OVER_ETH=m CONFIG_DUMMY_IRQ=m -CONFIG_IDE=y -CONFIG_IDE_GD_ATAPI=y -CONFIG_BLK_DEV_IDECD=y -CONFIG_BLK_DEV_GAYLE=y -CONFIG_BLK_DEV_BUDDHA=y CONFIG_RAID_ATTRS=m CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y
@@ -344,6 +339,11 @@ CONFIG_GVP11_SCSI=y CONFIG_SCSI_A4000T=y CONFIG_SCSI_ZORRO7XX=y CONFIG_SCSI_ZORRO_ESP=y +CONFIG_ATA=y +# CONFIG_ATA_VERBOSE_ERROR is not set +# CONFIG_ATA_BMDMA is not set +CONFIG_PATA_GAYLE=y +CONFIG_PATA_BUDDHA=y CONFIG_MD=y CONFIG_MD_LINEAR=m CONFIG_BLK_DEV_DM=m
arch/m68k/configs/atari_defconfig +4 -4
@@ -324,10 +324,6 @@ CONFIG_BLK_DEV_RAM=y CONFIG_CDROM_PKTCDVD=m CONFIG_ATA_OVER_ETH=m CONFIG_DUMMY_IRQ=m -CONFIG_IDE=y -CONFIG_IDE_GD_ATAPI=y -CONFIG_BLK_DEV_IDECD=y -CONFIG_BLK_DEV_FALCON_IDE=y CONFIG_RAID_ATTRS=m CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y
@@ -339,6 +335,10 @@ CONFIG_SCSI_SAS_ATTRS=m CONFIG_ISCSI_TCP=m CONFIG_ISCSI_BOOT_SYSFS=m CONFIG_ATARI_SCSI=y +CONFIG_ATA=y +# CONFIG_ATA_VERBOSE_ERROR is not set +# CONFIG_ATA_BMDMA is not set +CONFIG_PATA_FALCON=y CONFIG_MD=y CONFIG_MD_LINEAR=m CONFIG_BLK_DEV_DM=m
arch/m68k/configs/mac_defconfig +4 -4
@@ -315,10 +315,6 @@ CONFIG_BLK_DEV_RAM=y CONFIG_CDROM_PKTCDVD=m CONFIG_ATA_OVER_ETH=m CONFIG_DUMMY_IRQ=m -CONFIG_IDE=y -CONFIG_IDE_GD_ATAPI=y -CONFIG_BLK_DEV_IDECD=y -CONFIG_BLK_DEV_PLATFORM=y CONFIG_RAID_ATTRS=m CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y
@@ -331,6 +327,10 @@ CONFIG_ISCSI_TCP=m CONFIG_ISCSI_BOOT_SYSFS=m CONFIG_MAC_SCSI=y CONFIG_SCSI_MAC_ESP=y +CONFIG_ATA=y +# CONFIG_ATA_VERBOSE_ERROR is not set +# CONFIG_ATA_BMDMA is not set +CONFIG_PATA_PLATFORM=y CONFIG_MD=y CONFIG_MD_LINEAR=m CONFIG_BLK_DEV_DM=m
arch/m68k/configs/multi_defconfig +7 -7
@@ -344,13 +344,6 @@ CONFIG_BLK_DEV_RAM=y CONFIG_CDROM_PKTCDVD=m CONFIG_ATA_OVER_ETH=m CONFIG_DUMMY_IRQ=m -CONFIG_IDE=y -CONFIG_IDE_GD_ATAPI=y -CONFIG_BLK_DEV_IDECD=y -CONFIG_BLK_DEV_PLATFORM=y -CONFIG_BLK_DEV_GAYLE=y -CONFIG_BLK_DEV_BUDDHA=y -CONFIG_BLK_DEV_FALCON_IDE=y CONFIG_RAID_ATTRS=m CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y
@@ -374,6 +367,13 @@ CONFIG_MVME147_SCSI=y CONFIG_MVME16x_SCSI=y CONFIG_BVME6000_SCSI=y CONFIG_SUN3X_ESP=y +CONFIG_ATA=y +# CONFIG_ATA_VERBOSE_ERROR is not set +# CONFIG_ATA_BMDMA is not set +CONFIG_PATA_FALCON=y +CONFIG_PATA_GAYLE=y +CONFIG_PATA_BUDDHA=y +CONFIG_PATA_PLATFORM=y CONFIG_MD=y CONFIG_MD_LINEAR=m CONFIG_BLK_DEV_DM=m
arch/m68k/configs/q40_defconfig +4 -4
@@ -314,10 +314,6 @@ CONFIG_BLK_DEV_RAM=y CONFIG_CDROM_PKTCDVD=m CONFIG_ATA_OVER_ETH=m CONFIG_DUMMY_IRQ=m -CONFIG_IDE=y -CONFIG_IDE_GD_ATAPI=y -CONFIG_BLK_DEV_IDECD=y -CONFIG_BLK_DEV_FALCON_IDE=y CONFIG_RAID_ATTRS=m CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y
@@ -328,6 +324,10 @@ CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_SAS_ATTRS=m CONFIG_ISCSI_TCP=m CONFIG_ISCSI_BOOT_SYSFS=m +CONFIG_ATA=y +# CONFIG_ATA_VERBOSE_ERROR is not set +# CONFIG_ATA_BMDMA is not set +CONFIG_PATA_FALCON=y CONFIG_MD=y CONFIG_MD_LINEAR=m CONFIG_BLK_DEV_DM=m
Signature · 1 line
2.30.2
Re: [PATCH 5/6] m68k: use libata instead of the legacy ide driver
Hi Christoph,
Quoted 3 lines · Christoph Hellwig
Switch the m68 defconfigs from the deprecated ide subsystem to use libata instead. The gayle and buddha and falcon drivers are enabled for libata, while support for the q40 and macide drivers is lost.
I guess you forgot to update the last sentence, too?
These are now handled by the falcon and generic platform libata drivers.
Quoted 8 lines
Signed-off-by Christoph Hellwig <[email protected]>--- arch/m68k/configs/amiga_defconfig | 10 +++++----- arch/m68k/configs/atari_defconfig | 8 ++++---- arch/m68k/configs/mac_defconfig | 8 ++++---- arch/m68k/configs/multi_defconfig | 14 +++++++------- arch/m68k/configs/q40_defconfig | 8 ++++---- 5 files changed, 24 insertions(+), 24 deletions(-)
With the above fixed:
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Re: [PATCH 5/6] m68k: use libata instead of the legacy ide driver
Quoted 9 lines · Geert Uytterhoeven
Hi Christoph,
Quoted 3 lines · Christoph Hellwig
Switch the m68 defconfigs from the deprecated ide subsystem to use libata instead. The gayle and buddha and falcon drivers are enabled for libata, while support for the q40 and macide drivers is lost.
I guess you forgot to update the last sentence, too?
These are now handled by the falcon and generic platform libata drivers.
Indeed.
Quoted 2 lines
With the above fixed:
Thanks!
PATCH 6/6 ide: remove the legacy ide driver
In reply to Christoph HellwigThe legay ide driver has been replace with libata startin in 2003 and has been scheduled for removal for a while. Finally kill it off so that we can start cleaning up various bits of cruft it forced on the block layer.
--- Documentation/userspace-api/ioctl/hdio.rst | 845 +------- MAINTAINERS | 16 - drivers/Kconfig | 2 - drivers/Makefile | 1 - drivers/ide/Kconfig | 827 -------- drivers/ide/Makefile | 109 - drivers/ide/aec62xx.c | 331 ---- drivers/ide/ali14xx.c | 250 --- drivers/ide/alim15x3.c | 602 ------ drivers/ide/amd74xx.c | 343 ---- drivers/ide/atiixp.c | 212 -- drivers/ide/buddha.c | 238 --- drivers/ide/cmd640.c | 848 -------- drivers/ide/cmd64x.c | 452 ----- drivers/ide/cs5520.c | 168 -- drivers/ide/cs5530.c | 295 --- drivers/ide/cs5535.c | 216 -- drivers/ide/cs5536.c | 294 --- drivers/ide/cy82c693.c | 234 --- drivers/ide/delkin_cb.c | 181 -- drivers/ide/dtc2278.c | 155 -- drivers/ide/falconide.c | 226 --- drivers/ide/gayle.c | 188 -- drivers/ide/hpt366.c | 1545 --------------- drivers/ide/ht6560b.c | 383 ---- drivers/ide/icside.c | 692 ------- drivers/ide/ide-4drives.c | 65 - drivers/ide/ide-acpi.c | 622 ------ drivers/ide/ide-atapi.c | 756 ------- drivers/ide/ide-cd.c | 1858 ----------------- drivers/ide/ide-cd.h | 123 -- drivers/ide/ide-cd_ioctl.c | 468 ----- drivers/ide/ide-cd_verbose.c | 362 ---- drivers/ide/ide-cs.c | 364 ---- drivers/ide/ide-devsets.c | 192 -- drivers/ide/ide-disk.c | 795 -------- drivers/ide/ide-disk.h | 30 - drivers/ide/ide-disk_ioctl.c | 33 - drivers/ide/ide-disk_proc.c | 125 -- drivers/ide/ide-dma-sff.c | 336 ---- drivers/ide/ide-dma.c | 551 ------ drivers/ide/ide-eh.c | 443 ----- drivers/ide/ide-floppy.c | 551 ------ drivers/ide/ide-floppy.h | 42 - drivers/ide/ide-floppy_ioctl.c | 339 ---- drivers/ide/ide-floppy_proc.c | 34 - drivers/ide/ide-gd.c | 432 ---- drivers/ide/ide-gd.h | 43 - drivers/ide/ide-generic.c | 139 -- drivers/ide/ide-io-std.c | 262 --- drivers/ide/ide-io.c | 904 --------- drivers/ide/ide-ioctls.c | 306 --- drivers/ide/ide-iops.c | 536 ----- drivers/ide/ide-legacy.c | 59 - drivers/ide/ide-lib.c | 146 -- drivers/ide/ide-park.c | 155 -- drivers/ide/ide-pci-generic.c | 203 -- drivers/ide/ide-pio-blacklist.c | 96 - drivers/ide/ide-pm.c | 261 --- drivers/ide/ide-pnp.c | 92 - drivers/ide/ide-probe.c | 1623 --------------- drivers/ide/ide-proc.c | 633 ------ drivers/ide/ide-scan-pci.c | 113 -- drivers/ide/ide-sysfs.c | 143 -- drivers/ide/ide-tape.c | 2083 -------------------- drivers/ide/ide-taskfile.c | 668 ------- drivers/ide/ide-timings.c | 198 -- drivers/ide/ide-xfer-mode.c | 267 --- drivers/ide/ide.c | 415 ---- drivers/ide/ide_platform.c | 133 -- drivers/ide/it8172.c | 165 -- drivers/ide/it8213.c | 217 -- drivers/ide/it821x.c | 715 ------- drivers/ide/jmicron.c | 176 -- drivers/ide/ns87415.c | 350 ---- drivers/ide/opti621.c | 179 -- drivers/ide/palm_bk3710.c | 387 ---- drivers/ide/pdc202xx_new.c | 557 ------ drivers/ide/pdc202xx_old.c | 362 ---- drivers/ide/piix.c | 476 ----- drivers/ide/pmac.c | 1703 ---------------- drivers/ide/qd65xx.c | 446 ----- drivers/ide/qd65xx.h | 145 -- drivers/ide/rapide.c | 106 - drivers/ide/rz1000.c | 100 - drivers/ide/sc1200.c | 355 ---- drivers/ide/serverworks.c | 456 ----- drivers/ide/setup-pci.c | 682 ------- drivers/ide/siimage.c | 843 -------- drivers/ide/sis5513.c | 637 ------ drivers/ide/sl82c105.c | 367 ---- drivers/ide/slc90e66.c | 182 -- drivers/ide/tc86c001.c | 270 --- drivers/ide/triflex.c | 143 -- drivers/ide/trm290.c | 374 ---- drivers/ide/tx4938ide.c | 209 -- drivers/ide/tx4939ide.c | 628 ------ drivers/ide/umc8672.c | 184 -- drivers/ide/via82cxxx.c | 532 ----- include/linux/ide.h | 1623 --------------- 100 files changed, 25 insertions(+), 41196 deletions(-) delete mode 100644 drivers/ide/Kconfig delete mode 100644 drivers/ide/Makefile delete mode 100644 drivers/ide/aec62xx.c delete mode 100644 drivers/ide/ali14xx.c delete mode 100644 drivers/ide/alim15x3.c delete mode 100644 drivers/ide/amd74xx.c delete mode 100644 drivers/ide/atiixp.c delete mode 100644 drivers/ide/buddha.c delete mode 100644 drivers/ide/cmd640.c delete mode 100644 drivers/ide/cmd64x.c delete mode 100644 drivers/ide/cs5520.c delete mode 100644 drivers/ide/cs5530.c delete mode 100644 drivers/ide/cs5535.c delete mode 100644 drivers/ide/cs5536.c delete mode 100644 drivers/ide/cy82c693.c delete mode 100644 drivers/ide/delkin_cb.c delete mode 100644 drivers/ide/dtc2278.c delete mode 100644 drivers/ide/falconide.c delete mode 100644 drivers/ide/gayle.c delete mode 100644 drivers/ide/hpt366.c delete mode 100644 drivers/ide/ht6560b.c delete mode 100644 drivers/ide/icside.c delete mode 100644 drivers/ide/ide-4drives.c delete mode 100644 drivers/ide/ide-acpi.c delete mode 100644 drivers/ide/ide-atapi.c delete mode 100644 drivers/ide/ide-cd.c delete mode 100644 drivers/ide/ide-cd.h delete mode 100644 drivers/ide/ide-cd_ioctl.c delete mode 100644 drivers/ide/ide-cd_verbose.c delete mode 100644 drivers/ide/ide-cs.c delete mode 100644 drivers/ide/ide-devsets.c delete mode 100644 drivers/ide/ide-disk.c delete mode 100644 drivers/ide/ide-disk.h delete mode 100644 drivers/ide/ide-disk_ioctl.c delete mode 100644 drivers/ide/ide-disk_proc.c delete mode 100644 drivers/ide/ide-dma-sff.c delete mode 100644 drivers/ide/ide-dma.c delete mode 100644 drivers/ide/ide-eh.c delete mode 100644 drivers/ide/ide-floppy.c delete mode 100644 drivers/ide/ide-floppy.h delete mode 100644 drivers/ide/ide-floppy_ioctl.c delete mode 100644 drivers/ide/ide-floppy_proc.c delete mode 100644 drivers/ide/ide-gd.c delete mode 100644 drivers/ide/ide-gd.h delete mode 100644 drivers/ide/ide-generic.c delete mode 100644 drivers/ide/ide-io-std.c delete mode 100644 drivers/ide/ide-io.c delete mode 100644 drivers/ide/ide-ioctls.c delete mode 100644 drivers/ide/ide-iops.c delete mode 100644 drivers/ide/ide-legacy.c delete mode 100644 drivers/ide/ide-lib.c delete mode 100644 drivers/ide/ide-park.c delete mode 100644 drivers/ide/ide-pci-generic.c delete mode 100644 drivers/ide/ide-pio-blacklist.c delete mode 100644 drivers/ide/ide-pm.c delete mode 100644 drivers/ide/ide-pnp.c delete mode 100644 drivers/ide/ide-probe.c delete mode 100644 drivers/ide/ide-proc.c delete mode 100644 drivers/ide/ide-scan-pci.c delete mode 100644 drivers/ide/ide-sysfs.c delete mode 100644 drivers/ide/ide-tape.c delete mode 100644 drivers/ide/ide-taskfile.c delete mode 100644 drivers/ide/ide-timings.c delete mode 100644 drivers/ide/ide-xfer-mode.c delete mode 100644 drivers/ide/ide.c delete mode 100644 drivers/ide/ide_platform.c delete mode 100644 drivers/ide/it8172.c delete mode 100644 drivers/ide/it8213.c delete mode 100644 drivers/ide/it821x.c delete mode 100644 drivers/ide/jmicron.c delete mode 100644 drivers/ide/ns87415.c delete mode 100644 drivers/ide/opti621.c delete mode 100644 drivers/ide/palm_bk3710.c delete mode 100644 drivers/ide/pdc202xx_new.c delete mode 100644 drivers/ide/pdc202xx_old.c delete mode 100644 drivers/ide/piix.c delete mode 100644 drivers/ide/pmac.c delete mode 100644 drivers/ide/qd65xx.c delete mode 100644 drivers/ide/qd65xx.h delete mode 100644 drivers/ide/rapide.c delete mode 100644 drivers/ide/rz1000.c delete mode 100644 drivers/ide/sc1200.c delete mode 100644 drivers/ide/serverworks.c delete mode 100644 drivers/ide/setup-pci.c delete mode 100644 drivers/ide/siimage.c delete mode 100644 drivers/ide/sis5513.c delete mode 100644 drivers/ide/sl82c105.c delete mode 100644 drivers/ide/slc90e66.c delete mode 100644 drivers/ide/tc86c001.c delete mode 100644 drivers/ide/triflex.c delete mode 100644 drivers/ide/trm290.c delete mode 100644 drivers/ide/tx4938ide.c delete mode 100644 drivers/ide/tx4939ide.c delete mode 100644 drivers/ide/umc8672.c delete mode 100644 drivers/ide/via82cxxx.c delete mode 100644 include/linux/ide.h
Documentation/userspace-api/ioctl/hdio.rst +25 -820
@@ -7,8 +7,8 @@ Summary of `HDIO_` ioctl calls November, 2004 This document attempts to describe the ioctl(2) calls supported by -the HD/IDE layer. These are by-and-large implemented (as of Linux 2.6) -in drivers/ide/ide.c and drivers/block/scsi_ioctl.c +the HD/IDE layer. These are by-and-large implemented (as of Linux 5.11) +drivers/ata/libata-scsi.c. ioctl values are listed in <linux/hdreg.h>. As of this writing, they are as follows:
@@ -17,50 +17,17 @@ are as follows: ======================= ======================================= HDIO_GETGEO get device geometry - HDIO_GET_UNMASKINTR get current unmask setting - HDIO_GET_MULTCOUNT get current IDE blockmode setting - HDIO_GET_QDMA get use-qdma flag - HDIO_SET_XFER set transfer rate via proc - HDIO_OBSOLETE_IDENTITY OBSOLETE, DO NOT USE - HDIO_GET_KEEPSETTINGS get keep-settings-on-reset flag HDIO_GET_32BIT get current io_32bit setting - HDIO_GET_NOWERR get ignore-write-error flag - HDIO_GET_DMA get use-dma flag - HDIO_GET_NICE get nice flags HDIO_GET_IDENTITY get IDE identification info - HDIO_GET_WCACHE get write cache mode on|off - HDIO_GET_ACOUSTIC get acoustic value - HDIO_GET_ADDRESS get sector addressing mode - HDIO_GET_BUSSTATE get the bus state of the hwif - HDIO_TRISTATE_HWIF execute a channel tristate - HDIO_DRIVE_RESET execute a device reset HDIO_DRIVE_TASKFILE execute raw taskfile HDIO_DRIVE_TASK execute task and special drive command HDIO_DRIVE_CMD execute a special drive command - HDIO_DRIVE_CMD_AEB HDIO_DRIVE_TASK ======================= ======================================= ioctls that pass non-pointer values: ======================= ======================================= - HDIO_SET_MULTCOUNT change IDE blockmode - HDIO_SET_UNMASKINTR permit other irqs during I/O - HDIO_SET_KEEPSETTINGS keep ioctl settings on reset HDIO_SET_32BIT change io_32bit flags - HDIO_SET_NOWERR change ignore-write-error flag - HDIO_SET_DMA change use-dma flag - HDIO_SET_PIO_MODE reconfig interface to new speed - HDIO_SCAN_HWIF register and (re)scan interface - HDIO_SET_NICE set nice flags - HDIO_UNREGISTER_HWIF unregister interface - HDIO_SET_WCACHE change write cache enable-disable - HDIO_SET_ACOUSTIC change acoustic behavior - HDIO_SET_BUSSTATE set the bus state of the hwif - HDIO_SET_QDMA change use-qdma flag - HDIO_SET_ADDRESS change lba addressing modes - - HDIO_SET_IDE_SCSI Set scsi emulation mode on/off - HDIO_SET_SCSI_IDE not implemented yet ======================= =======================================
@@ -137,512 +104,49 @@ HDIO_GETGEO - -HDIO_GET_UNMASKINTR - get current unmask setting - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_UNMASKINTR, &val); - - inputs: - none - - - - outputs: - The value of the drive's current unmask setting - - - - - -HDIO_SET_UNMASKINTR - permit other irqs during I/O - - - usage:: - - unsigned long val; - - ioctl(fd, HDIO_SET_UNMASKINTR, val); - - inputs: - New value for unmask flag - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - - -HDIO_GET_MULTCOUNT - get current IDE blockmode setting - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_MULTCOUNT, &val); - - inputs: - none - - - - outputs: - The value of the current IDE block mode setting. This - controls how many sectors the drive will transfer per - interrupt. - - - -HDIO_SET_MULTCOUNT - change IDE blockmode - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_MULTCOUNT, val); - - inputs: - New value for IDE block mode setting. This controls how many - sectors the drive will transfer per interrupt. - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range supported by disk. - - EBUSY Controller busy or blockmode already set. - - EIO Drive did not accept new block mode. - - notes: - Source code comments read:: - - This is tightly woven into the driver->do_special cannot - touch. DON'T do it again until a total personality rewrite - is committed. - - If blockmode has already been set, this ioctl will fail with - -EBUSY - - - -HDIO_GET_QDMA - get use-qdma flag - - - Not implemented, as of 2.6.8.1 - - - -HDIO_SET_XFER - set transfer rate via proc - - - Not implemented, as of 2.6.8.1 - - - -HDIO_OBSOLETE_IDENTITY - OBSOLETE, DO NOT USE - - - Same as HDIO_GET_IDENTITY (see below), except that it only - returns the first 142 bytes of drive identity information. - - - -HDIO_GET_IDENTITY - get IDE identification info - - - usage:: - - unsigned char identity[512]; - - ioctl(fd, HDIO_GET_IDENTITY, identity); - - inputs: - none - - - - outputs: - ATA drive identity information. For full description, see - the IDENTIFY DEVICE and IDENTIFY PACKET DEVICE commands in - the ATA specification. - - error returns: - - EINVAL Called on a partition instead of the whole disk device - - ENOMSG IDENTIFY DEVICE information not available - - notes: - Returns information that was obtained when the drive was - probed. Some of this information is subject to change, and - this ioctl does not re-probe the drive to update the - information. - - This information is also available from /proc/ide/hdX/identify - - - -HDIO_GET_KEEPSETTINGS - get keep-settings-on-reset flag - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_KEEPSETTINGS, &val); - - inputs: - none - - - - outputs: - The value of the current "keep settings" flag - - - - notes: - When set, indicates that kernel should restore settings - after a drive reset. - - - -HDIO_SET_KEEPSETTINGS - keep ioctl settings on reset - - - usage:: - - long val; - - ioctl(fd, HDIO_SET_KEEPSETTINGS, val); - - inputs: - New value for keep_settings flag - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_GET_32BIT - get current io_32bit setting - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_32BIT, &val); - - inputs: - none - - - - outputs: - The value of the current io_32bit setting - - - - notes: - 0=16-bit, 1=32-bit, 2,3 = 32bit+sync - - - - - -HDIO_GET_NOWERR - get ignore-write-error flag - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_NOWERR, &val); - - inputs: - none - - - - outputs: - The value of the current ignore-write-error flag - - - - - -HDIO_GET_DMA - get use-dma flag - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_DMA, &val); - - inputs: - none - - - - outputs: - The value of the current use-dma flag - - - - - -HDIO_GET_NICE - get nice flags - - - usage:: - - long nice; - - ioctl(fd, HDIO_GET_NICE, &nice); - - inputs: - none - - - - outputs: - The drive's "nice" values. - - - - notes: - Per-drive flags which determine when the system will give more - bandwidth to other devices sharing the same IDE bus. - - See <linux/hdreg.h>, near symbol IDE_NICE_DSC_OVERLAP. - - - - -HDIO_SET_NICE - set nice flags - - - usage:: - - unsigned long nice; - - ... - ioctl(fd, HDIO_SET_NICE, nice); - - inputs: - bitmask of nice flags. - - - - outputs: - none - - - - error returns: - - EACCES Access denied: requires CAP_SYS_ADMIN - - EPERM Flags other than DSC_OVERLAP and NICE_1 set. - - EPERM DSC_OVERLAP specified but not supported by drive - - notes: - This ioctl sets the DSC_OVERLAP and NICE_1 flags from values - provided by the user. - - Nice flags are listed in <linux/hdreg.h>, starting with - IDE_NICE_DSC_OVERLAP. These values represent shifts. - - - - - -HDIO_GET_WCACHE - get write cache mode on|off - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_WCACHE, &val); - - inputs: - none - - - - outputs: - The value of the current write cache mode - - - - - -HDIO_GET_ACOUSTIC - get acoustic value - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_ACOUSTIC, &val); - - inputs: - none - - - - outputs: - The value of the current acoustic settings - - - - notes: - See HDIO_SET_ACOUSTIC - - - - - -HDIO_GET_ADDRESS - usage:: - - - long val; - - ioctl(fd, HDIO_GET_ADDRESS, &val); - - inputs: - none - - - - outputs: - The value of the current addressing mode: - - = =================== - 0 28-bit - 1 48-bit - 2 48-bit doing 28-bit - 3 64-bit - = =================== - - - -HDIO_GET_BUSSTATE - get the bus state of the hwif - - - usage:: - - long state; - - ioctl(fd, HDIO_SCAN_HWIF, &state); - - inputs: - none - - - - outputs: - Current power state of the IDE bus. One of BUSSTATE_OFF, - BUSSTATE_ON, or BUSSTATE_TRISTATE - - error returns: - - EACCES Access denied: requires CAP_SYS_ADMIN - - - - -HDIO_SET_BUSSTATE - set the bus state of the hwif +HDIO_GET_IDENTITY + get IDE identification info usage:: - int state; + unsigned char identity[512]; - ... - ioctl(fd, HDIO_SCAN_HWIF, state); + ioctl(fd, HDIO_GET_IDENTITY, identity); inputs: - Desired IDE power state. One of BUSSTATE_OFF, BUSSTATE_ON, - or BUSSTATE_TRISTATE - - outputs: none - error returns: - - EACCES Access denied: requires CAP_SYS_RAWIO - - EOPNOTSUPP Hardware interface does not support bus power control - - - + outputs: + ATA drive identity information. For full description, see + the IDENTIFY DEVICE and IDENTIFY PACKET DEVICE commands in + the ATA specification. -HDIO_TRISTATE_HWIF - execute a channel tristate + error returns: + - EINVAL Called on a partition instead of the whole disk device + - ENOMSG IDENTIFY DEVICE information not available + notes: + Returns information that was obtained when the drive was + probed. Some of this information is subject to change, and + this ioctl does not re-probe the drive to update the + information. - Not implemented, as of 2.6.8.1. See HDIO_SET_BUSSTATE + This information is also available from /proc/ide/hdX/identify -HDIO_DRIVE_RESET - execute a device reset +HDIO_GET_32BIT + get current io_32bit setting usage:: - int args[3] + long val; - ... - ioctl(fd, HDIO_DRIVE_RESET, args); + ioctl(fd, HDIO_GET_32BIT, &val); inputs: none
@@ -650,22 +154,12 @@ HDIO_DRIVE_RESET outputs: - none - + The value of the current io_32bit setting - error returns: - - EACCES Access denied: requires CAP_SYS_ADMIN - - ENXIO No such device: phy dead or ctl_addr == 0 - - EIO I/O error: reset timed out or hardware error notes: - - - Execute a reset on the device as soon as the current IO - operation has completed. - - - Executes an ATAPI soft reset if applicable, otherwise - executes an ATA soft reset on the controller. + 0=16-bit, 1=32-bit, 2,3 = 32bit+sync
@@ -1026,14 +520,6 @@ HDIO_DRIVE_TASK -HDIO_DRIVE_CMD_AEB - HDIO_DRIVE_TASK - - - Not implemented, as of 2.6.8.1 - - - HDIO_SET_32BIT change io_32bit flags
@@ -1059,284 +545,3 @@ HDIO_SET_32BIT - EACCES Access denied: requires CAP_SYS_ADMIN - EINVAL value out of range [0 3] - EBUSY Controller busy - - - - -HDIO_SET_NOWERR - change ignore-write-error flag - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_NOWERR, val); - - inputs: - New value for ignore-write-error flag. Used for ignoring - - - WRERR_STAT - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_SET_DMA - change use-dma flag - - - usage:: - - long val; - - ioctl(fd, HDIO_SET_DMA, val); - - inputs: - New value for use-dma flag - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_SET_PIO_MODE - reconfig interface to new speed - - - usage:: - - long val; - - ioctl(fd, HDIO_SET_PIO_MODE, val); - - inputs: - New interface speed. - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 255] - - EBUSY Controller busy - - - -HDIO_SCAN_HWIF - register and (re)scan interface - - - usage:: - - int args[3] - - ... - ioctl(fd, HDIO_SCAN_HWIF, args); - - inputs: - - ======= ========================= - args[0] io address to probe - - - args[1] control address to probe - args[2] irq number - ======= ========================= - - outputs: - none - - - - error returns: - - EACCES Access denied: requires CAP_SYS_RAWIO - - EIO Probe failed. - - notes: - This ioctl initializes the addresses and irq for a disk - controller, probes for drives, and creates /proc/ide - interfaces as appropriate. - - - -HDIO_UNREGISTER_HWIF - unregister interface - - - usage:: - - int index; - - ioctl(fd, HDIO_UNREGISTER_HWIF, index); - - inputs: - index index of hardware interface to unregister - - - - outputs: - none - - - - error returns: - - EACCES Access denied: requires CAP_SYS_RAWIO - - notes: - This ioctl removes a hardware interface from the kernel. - - Currently (2.6.8) this ioctl silently fails if any drive on - the interface is busy. - - - -HDIO_SET_WCACHE - change write cache enable-disable - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_WCACHE, val); - - inputs: - New value for write cache enable - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_SET_ACOUSTIC - change acoustic behavior - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_ACOUSTIC, val); - - inputs: - New value for drive acoustic settings - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 254] - - EBUSY Controller busy - - - -HDIO_SET_QDMA - change use-qdma flag - - - Not implemented, as of 2.6.8.1 - - - -HDIO_SET_ADDRESS - change lba addressing modes - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_ADDRESS, val); - - inputs: - New value for addressing mode - - = =================== - 0 28-bit - 1 48-bit - 2 48-bit doing 28-bit - = =================== - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 2] - - EBUSY Controller busy - - EIO Drive does not support lba48 mode. - - -HDIO_SET_IDE_SCSI - usage:: - - - long val; - - ioctl(fd, HDIO_SET_IDE_SCSI, val); - - inputs: - New value for scsi emulation mode (?) - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_SET_SCSI_IDE - Not implemented, as of 2.6.8.1
MAINTAINERS +0 -16
@@ -8763,22 +8763,6 @@ L: [email protected] S: Maintained F: drivers/i2c/busses/i2c-icy.c -IDE SUBSYSTEM -M: "David S. Miller" <[email protected]> -L: [email protected] -S: Maintained -Q: http://patchwork.ozlabs.org/project/linux-ide/list/ -T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide.git -F: Documentation/ide/ -F: drivers/ide/ -F: include/linux/ide.h - -IDE/ATAPI DRIVERS -L: [email protected] -S: Orphan -F: Documentation/cdrom/ide-cd.rst -F: drivers/ide/ide-cd* - IDEAPAD LAPTOP EXTRAS DRIVER M: Ike Panhc <[email protected]> L: [email protected]
drivers/Kconfig +0 -2
@@ -33,8 +33,6 @@ source "drivers/nvme/Kconfig" source "drivers/misc/Kconfig" -source "drivers/ide/Kconfig" - source "drivers/scsi/Kconfig" source "drivers/ata/Kconfig"
drivers/Makefile +0 -1
@@ -78,7 +78,6 @@ obj-$(CONFIG_CXL_BUS) += cxl/ obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf/ obj-$(CONFIG_NUBUS) += nubus/ obj-y += macintosh/ -obj-$(CONFIG_IDE) += ide/ obj-y += scsi/ obj-y += nvme/ obj-$(CONFIG_ATA) += ata/
drivers/ide/Kconfig deleted +0 -827
827 lines not on this page · raw message
drivers/ide/Makefile deleted +0 -109
109 lines not on this page · raw message
drivers/ide/aec62xx.c deleted +0 -331
331 lines not on this page · raw message
drivers/ide/ali14xx.c deleted +0 -250
250 lines not on this page · raw message
drivers/ide/alim15x3.c deleted +0 -602
531 lines not on this page · raw message
drivers/ide/amd74xx.c deleted +0 -343
343 lines not on this page · raw message
drivers/ide/atiixp.c deleted +0 -212
212 lines not on this page · raw message
drivers/ide/buddha.c deleted +0 -238
238 lines not on this page · raw message
drivers/ide/cmd640.c deleted +0 -848
848 lines not on this page · raw message
drivers/ide/cmd64x.c deleted +0 -452
452 lines not on this page · raw message
drivers/ide/cs5520.c deleted +0 -168
168 lines not on this page · raw message
drivers/ide/cs5530.c deleted +0 -295
295 lines not on this page · raw message
drivers/ide/cs5535.c deleted +0 -216
216 lines not on this page · raw message
drivers/ide/cs5536.c deleted +0 -294
294 lines not on this page · raw message
drivers/ide/cy82c693.c deleted +0 -234
234 lines not on this page · raw message
drivers/ide/delkin_cb.c deleted +0 -181
181 lines not on this page · raw message
drivers/ide/dtc2278.c deleted +0 -155
155 lines not on this page · raw message
drivers/ide/falconide.c deleted +0 -226
226 lines not on this page · raw message
drivers/ide/gayle.c deleted +0 -188
188 lines not on this page · raw message
drivers/ide/hpt366.c deleted +0 -1545
1,545 lines not on this page · raw message
drivers/ide/ht6560b.c deleted +0 -383
383 lines not on this page · raw message
drivers/ide/icside.c deleted +0 -692
692 lines not on this page · raw message
drivers/ide/ide-4drives.c deleted +0 -65
65 lines not on this page · raw message
drivers/ide/ide-acpi.c deleted +0 -622
622 lines not on this page · raw message
drivers/ide/ide-atapi.c deleted +0 -756
756 lines not on this page · raw message
drivers/ide/ide-cd.c deleted +0 -1858
1,858 lines not on this page · raw message
drivers/ide/ide-cd.h deleted +0 -123
123 lines not on this page · raw message
drivers/ide/ide-cd_ioctl.c deleted +0 -468
468 lines not on this page · raw message
drivers/ide/ide-cd_verbose.c deleted +0 -362
362 lines not on this page · raw message
drivers/ide/ide-cs.c deleted +0 -364
364 lines not on this page · raw message
drivers/ide/ide-devsets.c deleted +0 -192
192 lines not on this page · raw message
drivers/ide/ide-disk.c deleted +0 -795
795 lines not on this page · raw message
drivers/ide/ide-disk_proc.c deleted +0 -125
125 lines not on this page · raw message
drivers/ide/ide-dma-sff.c deleted +0 -336
336 lines not on this page · raw message
drivers/ide/ide-dma.c deleted +0 -551
551 lines not on this page · raw message
drivers/ide/ide-eh.c deleted +0 -443
443 lines not on this page · raw message
drivers/ide/ide-floppy.c deleted +0 -551
551 lines not on this page · raw message
drivers/ide/ide-floppy.h deleted +0 -42
42 lines not on this page · raw message
drivers/ide/ide-floppy_ioctl.c deleted +0 -339
339 lines not on this page · raw message
drivers/ide/ide-gd.c deleted +0 -432
432 lines not on this page · raw message
drivers/ide/ide-gd.h deleted +0 -43
43 lines not on this page · raw message
drivers/ide/ide-generic.c deleted +0 -139
139 lines not on this page · raw message
drivers/ide/ide-io-std.c deleted +0 -262
262 lines not on this page · raw message
drivers/ide/ide-io.c deleted +0 -904
904 lines not on this page · raw message
drivers/ide/ide-ioctls.c deleted +0 -306
306 lines not on this page · raw message
drivers/ide/ide-iops.c deleted +0 -536
536 lines not on this page · raw message
drivers/ide/ide-legacy.c deleted +0 -59
59 lines not on this page · raw message
drivers/ide/ide-lib.c deleted +0 -146
146 lines not on this page · raw message
drivers/ide/ide-park.c deleted +0 -155
155 lines not on this page · raw message
drivers/ide/ide-pci-generic.c deleted +0 -203
203 lines not on this page · raw message
drivers/ide/ide-pio-blacklist.c deleted +0 -96
96 lines not on this page · raw message
drivers/ide/ide-pm.c deleted +0 -261
261 lines not on this page · raw message
drivers/ide/ide-pnp.c deleted +0 -92
92 lines not on this page · raw message
drivers/ide/ide-probe.c deleted +0 -1623
1,623 lines not on this page · raw message
drivers/ide/ide-proc.c deleted +0 -633
633 lines not on this page · raw message
drivers/ide/ide-scan-pci.c deleted +0 -113
113 lines not on this page · raw message
drivers/ide/ide-sysfs.c deleted +0 -143
143 lines not on this page · raw message
drivers/ide/ide-tape.c deleted +0 -2083
2,083 lines not on this page · raw message
drivers/ide/ide-taskfile.c deleted +0 -668
668 lines not on this page · raw message
drivers/ide/ide-timings.c deleted +0 -198
198 lines not on this page · raw message
drivers/ide/ide-xfer-mode.c deleted +0 -267
267 lines not on this page · raw message
drivers/ide/ide.c deleted +0 -415
415 lines not on this page · raw message
drivers/ide/ide_platform.c deleted +0 -133
133 lines not on this page · raw message
drivers/ide/it8172.c deleted +0 -165
165 lines not on this page · raw message
drivers/ide/it8213.c deleted +0 -217
217 lines not on this page · raw message
drivers/ide/it821x.c deleted +0 -715
715 lines not on this page · raw message
drivers/ide/jmicron.c deleted +0 -176
176 lines not on this page · raw message
drivers/ide/ns87415.c deleted +0 -350
350 lines not on this page · raw message
drivers/ide/opti621.c deleted +0 -179
179 lines not on this page · raw message
drivers/ide/palm_bk3710.c deleted +0 -387
387 lines not on this page · raw message
drivers/ide/pdc202xx_new.c deleted +0 -557
557 lines not on this page · raw message
drivers/ide/pdc202xx_old.c deleted +0 -362
362 lines not on this page · raw message
drivers/ide/piix.c deleted +0 -476
476 lines not on this page · raw message
drivers/ide/pmac.c deleted +0 -1703
1,703 lines not on this page · raw message
drivers/ide/qd65xx.c deleted +0 -446
446 lines not on this page · raw message
drivers/ide/qd65xx.h deleted +0 -145
145 lines not on this page · raw message
drivers/ide/rapide.c deleted +0 -106
106 lines not on this page · raw message
drivers/ide/rz1000.c deleted +0 -100
100 lines not on this page · raw message
drivers/ide/sc1200.c deleted +0 -355
355 lines not on this page · raw message
drivers/ide/serverworks.c deleted +0 -456
456 lines not on this page · raw message
drivers/ide/setup-pci.c deleted +0 -682
682 lines not on this page · raw message
drivers/ide/siimage.c deleted +0 -843
843 lines not on this page · raw message
drivers/ide/sis5513.c deleted +0 -637
637 lines not on this page · raw message
drivers/ide/sl82c105.c deleted +0 -367
367 lines not on this page · raw message
drivers/ide/slc90e66.c deleted +0 -182
182 lines not on this page · raw message
drivers/ide/tc86c001.c deleted +0 -270
270 lines not on this page · raw message
drivers/ide/triflex.c deleted +0 -143
143 lines not on this page · raw message
drivers/ide/trm290.c deleted +0 -374
374 lines not on this page · raw message
drivers/ide/tx4938ide.c deleted +0 -209
209 lines not on this page · raw message
drivers/ide/tx4939ide.c deleted +0 -628
628 lines not on this page · raw message
drivers/ide/umc8672.c deleted +0 -184
184 lines not on this page · raw message
drivers/ide/via82cxxx.c deleted +0 -532
532 lines not on this page · raw message
include/linux/ide.h deleted +0 -1623
1,623 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.30.2
Part of the diff is not shown here. View the raw message.
Hi Christoph!
Quoted 6 lines · Christoph Hellwig
libata mostly covers all hardware supported by the legacy ide driver. There are three mips drivers that are not supported, but the linux-mips list could not identify any users of those. There also are two m68k drivers that do not have libata equivalents, which might or might not have users, so we'll need some input and possibly help from the m68k community here.
I think the m68k drivers are being addressed at the moment. But Geert will know more about the current status.
Adrian
Signature · 4 lines
.''`. John Paul Adrian Glaubitz : :' : Debian Developer - [email protected] `. `' Freie Universitaet Berlin - [email protected] `- GPG: 62FF 8A75 84E0 2956 9546 0006 7426 3B37 F5B5 F913
Quoted 10 lines · John Paul Adrian Glaubitz
Hi Christoph!
Quoted 6 lines · Christoph Hellwig
libata mostly covers all hardware supported by the legacy ide driver. There are three mips drivers that are not supported, but the linux-mips list could not identify any users of those. There also are two m68k drivers that do not have libata equivalents, which might or might not have users, so we'll need some input and possibly help from the m68k community here.
Quoted 2 lines
I think the m68k drivers are being addressed at the moment. But Geert will know more about the current status.
Actually they are, and the patches are in the libata tree. I just forgot to update the cover letter.
Quoted 10 lines · Christoph Hellwig
Hi all,
we've been trying to get rid of the legacy ide driver for a while now, and finally scheduled a removal for 2021, which is three month old now.
In general distros and most defconfigs have switched to libata long ago, but there are a few exceptions. This series first switches over all remaining defconfigs to use libata and then removes the legacy ide driver.
Quoted 8 lines
libata mostly covers all hardware supported by the legacy ide driver. There are three mips drivers that are not supported, but the linux-mips list could not identify any users of those. There also are two m68k drivers that do not have libata equivalents, which might or might not have users, so we'll need some input and possibly help from the m68k community here.
This series is against Jens' for-5.14/libata branch.
Unless someone complains loudly, I plan on queueing this up end this week.
Signature · 1 line
Jens Axboe
Quoted 18 lines · Jens Axboe
Quoted 17 lines · Christoph Hellwig
Hi all,
we've been trying to get rid of the legacy ide driver for a while now, and finally scheduled a removal for 2021, which is three month old now.
In general distros and most defconfigs have switched to libata long ago, but there are a few exceptions. This series first switches over all remaining defconfigs to use libata and then removes the legacy ide driver.
libata mostly covers all hardware supported by the legacy ide driver. There are three mips drivers that are not supported, but the linux-mips list could not identify any users of those. There also are two m68k drivers that do not have libata equivalents, which might or might not have users, so we'll need some input and possibly help from the m68k community here.
Quoted 4 lines
Quoted 1 line
This series is against Jens' for-5.14/libata branch.
Unless someone complains loudly, I plan on queueing this up end this week.
This has now been applied for 5.14, thanks.
Signature · 1 line
Jens Axboe