Skip to contentSkip to conversation

hwmon: (pmbus) Add support for MPS MP2949A

PATCH Superseded [email protected] 2 participants 3 messages Jun 18, 2021 – Jun 22, 2021

Subsystems (2)

v2 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 hwmon: (pmbus) Add support for MPS MP2949A

From: "Ainux.Wang" <[email protected]>

Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS). This is a triple-loop, digital, multi-phase controller.
This device:
- Supports up to three power rail.
- Provides 6 pulse-width modulations (PWMs), and can be configured up to 6-phase operation for Rail A , up to 2-phase operation for Rail B and up to 1-phase operation for Rail C.
- The PMBus registers are distributed into three pages: Page 0, Page 1, Page 2. Page 0 contains the registers for Rail A and most of the common settings for all of the rails. Page 1 contains register information for Rail B. Page 2 contains register information for Rail C.
- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and IMVP9 with only one DAC for each rail to generate REF.

---
 Documentation/hwmon/index.rst   |   1 +
 Documentation/hwmon/mp2949a.rst |  44 ++++++++++++
 drivers/hwmon/pmbus/Kconfig     |   9 +++
 drivers/hwmon/pmbus/Makefile    |   1 +
 drivers/hwmon/pmbus/mp2949a.c   | 119 ++++++++++++++++++++++++++++++++
 5 files changed, 174 insertions(+)
 create mode 100644 Documentation/hwmon/mp2949a.rst
 create mode 100644 drivers/hwmon/pmbus/mp2949a.c
Documentation/hwmon/index.rst +1 -0
index 9ed60fa84cbe..56aac3b1678d 100644
@@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
    mcp3021
    menf21bmc
    mlxreg-fan
+   mp2949a
    mp2975
    nct6683
    nct6775
Documentation/hwmon/mp2949a.rst new file +44 -0

44 lines not on this page · raw message

drivers/hwmon/pmbus/Kconfig +9 -0
index 37a5c39784fa..b1344b265976 100644
@@ -248,6 +248,15 @@ config SENSORS_MAX8688
 	  This driver can also be built as a module. If so, the module will
 	  be called max8688.
 
+config SENSORS_MP2949A
+	tristate "MPS MP2949A"
+	help
+	  If you say yes here you get hardware monitoring support for MPS
+	  MP2949A Triple Loop Digital Multi-Phase Controller.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called mp2949a.
+
 config SENSORS_MP2975
 	tristate "MPS MP2975"
 	help
drivers/hwmon/pmbus/Makefile +1 -0
index f8dcc27cd56a..bfb55ab12da1 100644
@@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751)	+= max20751.o
 obj-$(CONFIG_SENSORS_MAX31785)	+= max31785.o
 obj-$(CONFIG_SENSORS_MAX34440)	+= max34440.o
 obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
+obj-$(CONFIG_SENSORS_MP2949A)	+= mp2949a.o
 obj-$(CONFIG_SENSORS_MP2975)	+= mp2975.o
 obj-$(CONFIG_SENSORS_PM6764TR)	+= pm6764tr.o
 obj-$(CONFIG_SENSORS_PXE1610)	+= pxe1610.o
drivers/hwmon/pmbus/mp2949a.c new file +119 -0

119 lines not on this page · raw message

Signature · 1 line
2.18.1
maintainer
#1 lore raw
Quoted 16 lines · On Fri, Jun 18, 2021 at 11:09:34AM +0800, [email protected] wrote:

From: "Ainux.Wang" <[email protected]>

Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS). This is a triple-loop, digital, multi-phase controller.
This device:
- Supports up to three power rail.
- Provides 6 pulse-width modulations (PWMs), and can be configured up to 6-phase operation for Rail A , up to 2-phase operation for Rail B and up to 1-phase operation for Rail C.
- The PMBus registers are distributed into three pages: Page 0, Page 1, Page 2. Page 0 contains the registers for Rail A and most of the common settings for all of the rails. Page 1 contains register information for Rail B. Page 2 contains register information for Rail C.
- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and IMVP9 with only one DAC for each rail to generate REF.

Quoted 2 lines

---

Change log goes here. My normal response to patches with missing change log is:

<Formletter>
Change log goes here. If it is missing, I won't know what changed. That means I will have to dig out older patch versions to compare. That costs time and would hold up both this patch as well as all other patches which I still have to review.

For this reason, I will not review patches without change log. </Formletter>

so you are lucky that your previous version is recent enough that I remember at least some of it. However, please do provide change logs in the future.

Quoted 41 lines
 Documentation/hwmon/index.rst   |   1 +
 Documentation/hwmon/mp2949a.rst |  44 ++++++++++++
 drivers/hwmon/pmbus/Kconfig     |   9 +++
 drivers/hwmon/pmbus/Makefile    |   1 +
 drivers/hwmon/pmbus/mp2949a.c   | 119 ++++++++++++++++++++++++++++++++
 5 files changed, 174 insertions(+)
 create mode 100644 Documentation/hwmon/mp2949a.rst
 create mode 100644 drivers/hwmon/pmbus/mp2949a.c
Documentation/hwmon/index.rst +1 -0
index 9ed60fa84cbe..56aac3b1678d 100644
@@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
    mcp3021
    menf21bmc
    mlxreg-fan
+   mp2949a
    mp2975
    nct6683
    nct6775
Documentation/hwmon/mp2949a.rst new file +14 -0
new file mode 100644
index 000000000000..ac4084e067f1
@@ -0,0 +1,44 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp2949a
+====================
+
+Supported chips:
+
+  * MPS MP2949A
+
+    Prefix: 'mp2949a'
+
+Author:
+
+	Ainux Wang <[email protected]>

Documentation/hwmon/mp2949a.rst line 24

Quoted 10 lines
Documentation/hwmon/mp2949a.rst new file +10 -0
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+triple-loop, digital, multi-phase controller MP2949A.
+
+This device:
+
+- Supports up to three power rail.

rails

Documentation/hwmon/mp2949a.rst line 25

Quoted 1 line
Documentation/hwmon/mp2949a.rst new file +1 -0
+- Provides 6 pulse-width modulations (PWMs), and can be configured up

can be configured for ...

Documentation/hwmon/mp2949a.rst line 26

Quoted 1 line
Documentation/hwmon/mp2949a.rst new file +1 -0
+  to 6-phase operation for Rail A , up to 2-phase operation for Rail B

Rail B,

Documentation/hwmon/mp2949a.rst line 33

Quoted 7 lines
Documentation/hwmon/mp2949a.rst new file +7 -0
+  and up to 1-phase operation for Rail C.
+- The PMBus registers are distributed into three pages: Page 0, Page 1,
+  Page 2. Page 0 contains the registers for Rail A and most of the common
+  settings for all of the rails. Page 1 contains register information for
+  Rail B. Page 2 contains register information for Rail C.
+- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
+  IMVP9 with only one DAC for each rail to generate REF.

Please explain REF.

Documentation/hwmon/mp2949a.rst line 41

Quoted 8 lines
Documentation/hwmon/mp2949a.rst new file +8 -0
+
+Device supports:
+
+- SVID interface.
+- PMBus rev 1.2 interface.
+
+Device supports direct format for reading output power.
+Device supports linear format for reading input voltage and output current

input voltage, output current, and temperature.

Documentation/hwmon/mp2949a.rst line 44

Quoted 3 lines
Documentation/hwmon/mp2949a.rst new file +3 -0
+and temperature.
+Device supports VID for reading output voltage.
+The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.

The following

Quoted 50 lines
drivers/hwmon/pmbus/Kconfig +9 -0
index 37a5c39784fa..b1344b265976 100644
@@ -248,6 +248,15 @@ config SENSORS_MAX8688
 	  This driver can also be built as a module. If so, the module will
 	  be called max8688.
 
+config SENSORS_MP2949A
+	tristate "MPS MP2949A"
+	help
+	  If you say yes here you get hardware monitoring support for MPS
+	  MP2949A Triple Loop Digital Multi-Phase Controller.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called mp2949a.
+
 config SENSORS_MP2975
 	tristate "MPS MP2975"
 	help
drivers/hwmon/pmbus/Makefile +1 -0
index f8dcc27cd56a..bfb55ab12da1 100644
@@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751)	+= max20751.o
 obj-$(CONFIG_SENSORS_MAX31785)	+= max31785.o
 obj-$(CONFIG_SENSORS_MAX34440)	+= max34440.o
 obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
+obj-$(CONFIG_SENSORS_MP2949A)	+= mp2949a.o
 obj-$(CONFIG_SENSORS_MP2975)	+= mp2975.o
 obj-$(CONFIG_SENSORS_PM6764TR)	+= pm6764tr.o
 obj-$(CONFIG_SENSORS_PXE1610)	+= pxe1610.o
drivers/hwmon/pmbus/mp2949a.c new file +12 -0
new file mode 100644
index 000000000000..d68e8526abe3
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for Monolithic Power Systems MP2949A
+ *
+ * Copyright (c) 2021 Lemote Technologies. All rights reserved.
+ * Copyright (c) 2021 Ainux <[email protected]>
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>

drivers/hwmon/pmbus/mp2949a.c line 22

Quoted 10 lines
drivers/hwmon/pmbus/mp2949a.c new file +10 -0
+#include <linux/module.h>
+#include "pmbus.h"
+
+#define MP2949A_PAGE_NUM		3
+
+static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+	switch (reg) {
+	case PMBUS_VOUT_MODE:
+		/* This chip do not support the VOUT_MODE command. */

s/do/does/

This warrants a more detailed explanation: What happens if the command is sent to the chip, and why is it not possible to rely on the standard response to unsupported commands ?

Quoted 5 lines
drivers/hwmon/pmbus/mp2949a.c new file +5 -0
+		return -EINVAL;
+	default:
+		return -ENODATA;
+	}
+}

drivers/hwmon/pmbus/mp2949a.c line 37

Quoted 10 lines
drivers/hwmon/pmbus/mp2949a.c new file +10 -0
+
+static int mp2949a_identify(struct i2c_client *client,
+			    struct pmbus_driver_info *info)
+{
+	u8 vout_params;
+	int i, ret;
+
+	for (i = 0; i < MP2949A_PAGE_NUM; i++) {
+		/* Read the register with VOUT scaling value.*/
+		ret = pmbus_read_byte_data(client, i, PMBUS_VOUT_MODE);
                                                      ^^^^^^^^^^^^^^^

Should this be MFR_VR_CONFIG ?

drivers/hwmon/pmbus/mp2949a.c line 46

Quoted 9 lines
drivers/hwmon/pmbus/mp2949a.c new file +9 -0
+		if (ret < 0)
+			return ret;
+
+		/*
+		 * Rail A bit 5, Rail B bit 4, Rail C bit 3.
+		 * 1'b1: 5mV  (vr12/imvp8)
+		 * 1'b0: 10mv (imvp9)
+		 */
+		vout_params = ret & ~BIT(5-i);

space before and after '-'. vout_params is really unnecessary; just do the check directly in the if() statement.

drivers/hwmon/pmbus/mp2949a.c line 51

Quoted 5 lines
drivers/hwmon/pmbus/mp2949a.c new file +5 -0
+		if (vout_params)
+			info->vrm_version[i] = vr12;
+		else
+			info->vrm_version[i] = imvp9;
+

Unnecessary empty line.

checkpatch --strict reports this and the above problem, plus another alignment problem. Please fix everything it reports.

Quoted 71 lines
drivers/hwmon/pmbus/mp2949a.c new file +68 -0
+	}
+
+	return 0;
+}
+
+static struct pmbus_driver_info mp2949a_info = {
+	.pages = MP2949A_PAGE_NUM,
+	.format[PSC_VOLTAGE_IN] = linear,
+	.format[PSC_VOLTAGE_OUT] = vid,
+	.format[PSC_CURRENT_OUT] = linear,
+	.format[PSC_TEMPERATURE] = linear,
+	.format[PSC_POWER] = direct,
+	.m[PSC_POWER] = 1,
+	.b[PSC_POWER] = 0,
+	.R[PSC_POWER] = 0,
+	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+		PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+		PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
+	.func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+		PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+		PMBUS_HAVE_POUT,
+	.func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+		PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+		PMBUS_HAVE_POUT,
+	.identify = mp2949a_identify,
+	.read_byte_data = mp2949a_read_byte_data,
+};
+
+static int mp2949a_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	struct pmbus_driver_info *info;
+
+	info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
+			    GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	return pmbus_do_probe(client, info);
+}
+
+static const struct i2c_device_id mp2949a_id[] = {
+	{"mp2949a", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, mp2949a_id);
+
+static const struct of_device_id mp2949a_of_match[] = {
+	{.compatible = "mps,mp2949a"},
+	{}
+};
+MODULE_DEVICE_TABLE(of, mp2949a_of_match);
+
+static struct i2c_driver mp2949a_driver = {
+	.driver = {
+		.name = "mp2949a",
+		.of_match_table = of_match_ptr(mp2949a_of_match),
+	},
+	.probe = mp2949a_probe,
+	.id_table = mp2949a_id,
+};
+
+module_i2c_driver(mp2949a_driver);
+
+MODULE_AUTHOR("Ainux <[email protected]>");
+MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
+MODULE_LICENSE("GPL");
Signature · 1 line
2.18.1
author
#2 lore raw

Hi,Guenter
Thanks for the review. It all sounds reasonable. I'll address it all in v3.
Best regards,
Ainux Wang.

Quoted 304 lines · Guenter Roeck
Quoted 16 lines · On Fri, Jun 18, 2021 at 11:09:34AM +0800, [email protected] wrote:

From: "Ainux.Wang" <[email protected]>

Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS). This is a triple-loop, digital, multi-phase controller.
This device:
- Supports up to three power rail.
- Provides 6 pulse-width modulations (PWMs), and can be configured up to 6-phase operation for Rail A , up to 2-phase operation for Rail B and up to 1-phase operation for Rail C.
- The PMBus registers are distributed into three pages: Page 0, Page 1, Page 2. Page 0 contains the registers for Rail A and most of the common settings for all of the rails. Page 1 contains register information for Rail B. Page 2 contains register information for Rail C.
- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and IMVP9 with only one DAC for each rail to generate REF.

Quoted 2 lines

---

Change log goes here. My normal response to patches with missing change log is:

<Formletter>
Change log goes here. If it is missing, I won't know what changed. That means I will have to dig out older patch versions to compare. That costs time and would hold up both this patch as well as all other patches which I still have to review.

For this reason, I will not review patches without change log. </Formletter>

so you are lucky that your previous version is recent enough that I remember at least some of it. However, please do provide change logs in the future.

Quoted 41 lines
 Documentation/hwmon/index.rst   |   1 +
 Documentation/hwmon/mp2949a.rst |  44 ++++++++++++
 drivers/hwmon/pmbus/Kconfig     |   9 +++
 drivers/hwmon/pmbus/Makefile    |   1 +
 drivers/hwmon/pmbus/mp2949a.c   | 119 ++++++++++++++++++++++++++++++++
 5 files changed, 174 insertions(+)
 create mode 100644 Documentation/hwmon/mp2949a.rst
 create mode 100644 drivers/hwmon/pmbus/mp2949a.c
Documentation/hwmon/index.rst +1 -0
index 9ed60fa84cbe..56aac3b1678d 100644
@@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
    mcp3021
    menf21bmc
    mlxreg-fan
+   mp2949a
    mp2975
    nct6683
    nct6775
Documentation/hwmon/mp2949a.rst new file +14 -0
new file mode 100644
index 000000000000..ac4084e067f1
@@ -0,0 +1,44 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp2949a
+====================
+
+Supported chips:
+
+  * MPS MP2949A
+
+    Prefix: 'mp2949a'
+
+Author:
+
+     Ainux Wang <[email protected]>

Documentation/hwmon/mp2949a.rst line 24

Quoted 10 lines
Documentation/hwmon/mp2949a.rst new file +10 -0
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+triple-loop, digital, multi-phase controller MP2949A.
+
+This device:
+
+- Supports up to three power rail.

rails

Documentation/hwmon/mp2949a.rst line 25

Quoted 1 line
Documentation/hwmon/mp2949a.rst new file +1 -0
+- Provides 6 pulse-width modulations (PWMs), and can be configured up

can be configured for ...

Documentation/hwmon/mp2949a.rst line 26

Quoted 1 line
Documentation/hwmon/mp2949a.rst new file +1 -0
+  to 6-phase operation for Rail A , up to 2-phase operation for Rail B

Rail B,

Documentation/hwmon/mp2949a.rst line 33

Quoted 7 lines
Documentation/hwmon/mp2949a.rst new file +7 -0
+  and up to 1-phase operation for Rail C.
+- The PMBus registers are distributed into three pages: Page 0, Page 1,
+  Page 2. Page 0 contains the registers for Rail A and most of the common
+  settings for all of the rails. Page 1 contains register information for
+  Rail B. Page 2 contains register information for Rail C.
+- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
+  IMVP9 with only one DAC for each rail to generate REF.

Please explain REF.

Documentation/hwmon/mp2949a.rst line 41

Quoted 8 lines
Documentation/hwmon/mp2949a.rst new file +8 -0
+
+Device supports:
+
+- SVID interface.
+- PMBus rev 1.2 interface.
+
+Device supports direct format for reading output power.
+Device supports linear format for reading input voltage and output current

input voltage, output current, and temperature.

Documentation/hwmon/mp2949a.rst line 44

Quoted 3 lines
Documentation/hwmon/mp2949a.rst new file +3 -0
+and temperature.
+Device supports VID for reading output voltage.
+The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.

The following

Quoted 50 lines
drivers/hwmon/pmbus/Kconfig +9 -0
index 37a5c39784fa..b1344b265976 100644
@@ -248,6 +248,15 @@ config SENSORS_MAX8688
        This driver can also be built as a module. If so, the module will
        be called max8688.
 
+config SENSORS_MP2949A
+     tristate "MPS MP2949A"
+     help
+       If you say yes here you get hardware monitoring support for MPS
+       MP2949A Triple Loop Digital Multi-Phase Controller.
+
+       This driver can also be built as a module. If so, the module will
+       be called mp2949a.
+
 config SENSORS_MP2975
      tristate "MPS MP2975"
      help
drivers/hwmon/pmbus/Makefile +1 -0
index f8dcc27cd56a..bfb55ab12da1 100644
@@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751)      += max20751.o
 obj-$(CONFIG_SENSORS_MAX31785)       += max31785.o
 obj-$(CONFIG_SENSORS_MAX34440)       += max34440.o
 obj-$(CONFIG_SENSORS_MAX8688)        += max8688.o
+obj-$(CONFIG_SENSORS_MP2949A)        += mp2949a.o
 obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
 obj-$(CONFIG_SENSORS_PM6764TR)       += pm6764tr.o
 obj-$(CONFIG_SENSORS_PXE1610)        += pxe1610.o
drivers/hwmon/pmbus/mp2949a.c new file +12 -0
new file mode 100644
index 000000000000..d68e8526abe3
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for Monolithic Power Systems MP2949A
+ *
+ * Copyright (c) 2021 Lemote Technologies. All rights reserved.
+ * Copyright (c) 2021 Ainux <[email protected]>
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>

drivers/hwmon/pmbus/mp2949a.c line 22

Quoted 10 lines
drivers/hwmon/pmbus/mp2949a.c new file +10 -0
+#include <linux/module.h>
+#include "pmbus.h"
+
+#define MP2949A_PAGE_NUM             3
+
+static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+     switch (reg) {
+     case PMBUS_VOUT_MODE:
+             /* This chip do not support the VOUT_MODE command. */

s/do/does/

This warrants a more detailed explanation: What happens if the command is sent to the chip, and why is it not possible to rely on the standard response to unsupported commands ?

Quoted 5 lines
drivers/hwmon/pmbus/mp2949a.c new file +5 -0
+             return -EINVAL;
+     default:
+             return -ENODATA;
+     }
+}

drivers/hwmon/pmbus/mp2949a.c line 37

Quoted 10 lines
drivers/hwmon/pmbus/mp2949a.c new file +10 -0
+
+static int mp2949a_identify(struct i2c_client *client,
+                         struct pmbus_driver_info *info)
+{
+     u8 vout_params;
+     int i, ret;
+
+     for (i = 0; i < MP2949A_PAGE_NUM; i++) {
+             /* Read the register with VOUT scaling value.*/
+             ret = pmbus_read_byte_data(client, i, PMBUS_VOUT_MODE);
                                                      ^^^^^^^^^^^^^^^

Should this be MFR_VR_CONFIG ?

drivers/hwmon/pmbus/mp2949a.c line 46

Quoted 9 lines
drivers/hwmon/pmbus/mp2949a.c new file +9 -0
+             if (ret < 0)
+                     return ret;
+
+             /*
+              * Rail A bit 5, Rail B bit 4, Rail C bit 3.
+              * 1'b1: 5mV  (vr12/imvp8)
+              * 1'b0: 10mv (imvp9)
+              */
+             vout_params = ret & ~BIT(5-i);

space before and after '-'. vout_params is really unnecessary; just do the check directly in the if() statement.

drivers/hwmon/pmbus/mp2949a.c line 51

Quoted 5 lines
drivers/hwmon/pmbus/mp2949a.c new file +5 -0
+             if (vout_params)
+                     info->vrm_version[i] = vr12;
+             else
+                     info->vrm_version[i] = imvp9;
+

Unnecessary empty line.

checkpatch --strict reports this and the above problem, plus another alignment problem. Please fix everything it reports.

Quoted 71 lines
drivers/hwmon/pmbus/mp2949a.c new file +68 -1
+     }
+
+     return 0;
+}
+
+static struct pmbus_driver_info mp2949a_info = {
+     .pages = MP2949A_PAGE_NUM,
+     .format[PSC_VOLTAGE_IN] = linear,
+     .format[PSC_VOLTAGE_OUT] = vid,
+     .format[PSC_CURRENT_OUT] = linear,
+     .format[PSC_TEMPERATURE] = linear,
+     .format[PSC_POWER] = direct,
+     .m[PSC_POWER] = 1,
+     .b[PSC_POWER] = 0,
+     .R[PSC_POWER] = 0,
+     .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+             PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+             PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
+     .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+             PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+             PMBUS_HAVE_POUT,
+     .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+             PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+             PMBUS_HAVE_POUT,
+     .identify = mp2949a_identify,
+     .read_byte_data = mp2949a_read_byte_data,
+};
+
+static int mp2949a_probe(struct i2c_client *client,
+                       const struct i2c_device_id *id)
+{
+     struct pmbus_driver_info *info;
+
+     info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
+                         GFP_KERNEL);
+     if (!info)
+             return -ENOMEM;
+
+     return pmbus_do_probe(client, info);
+}
+
+static const struct i2c_device_id mp2949a_id[] = {
+     {"mp2949a", 0},
+     {}
+};
+
+MODULE_DEVICE_TABLE(i2c, mp2949a_id);
+
+static const struct of_device_id mp2949a_of_match[] = {
+     {.compatible = "mps,mp2949a"},
+     {}
+};
+MODULE_DEVICE_TABLE(of, mp2949a_of_match);
+
+static struct i2c_driver mp2949a_driver = {
+     .driver = {
+             .name = "mp2949a",
+             .of_match_table = of_match_ptr(mp2949a_of_match),
+     },
+     .probe = mp2949a_probe,
+     .id_table = mp2949a_id,
+};
+
+module_i2c_driver(mp2949a_driver);
+
+MODULE_AUTHOR("Ainux <[email protected]>");
+MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
+MODULE_LICENSE("GPL");
--

2.18.1