Skip to contentSkip to conversation

x86: Discard .note.gnu.property sections

PATCH In review Bin Meng 1 participant 2 messages Jun 18, 2021 – Jun 21, 2021 x86

lore
Share & tools
lore

Bin Meng

author
#0 lore raw

PATCH v2 1/1 x86: Discard .note.gnu.property sections

When switching to kernel.org x86_64 gcc 11.1.0 toolchain, u-boot.rom built from qemu-x86_defconfig no longer boots anymore. Investigation shows that U-Boot fails at a very early stage during the boot process, in fdtdec_prepare_fdt() where fdt_check_header() complains that there is not a valid device tree found at gd->fdt_blob which points to _end. Now _end points to an allocated section .note.gnu.property which of course is wrong.

This issue is however not seen when using the default Ubuntu 20.04 gnu toolchain (gcc 9.3.0 with binutils 2.34). Further investigation shows that it is caused by a behavior change of binutils v2.36 which is part of the kernel.org gcc 11.1.0 toolchain, via the following commit:

939b95c77bf2 ("Linux/x86: Configure gas with --enable-x86-used-note by default")

In fact, there was already a regression bug report [1] for binutils two months ago, but the binutils folks did not think it is a bug :(

To resolve this, there are several options:

* pass -Wa,-mx86-used-note=no to gas
* pass -R .note.gnu.property to objcopy
* discard the section in the linker script

Linux kernel uses the discard way [2], so let's do the same for U-Boot.

[1] https://sourceware.org/bugzilla/show_bug.cgi?id=27753
[2] commit 4caffe6a28d3 ("x86/vdso: Discard .note.gnu.property sections in vDSO")

---

Changes in v2:
- add the same change to u-boot-spl.lds and u-boot-64.lds

 arch/x86/cpu/u-boot-64.lds  | 1 +
 arch/x86/cpu/u-boot-spl.lds | 1 +
 arch/x86/cpu/u-boot.lds     | 1 +
 3 files changed, 3 insertions(+)
arch/x86/cpu/u-boot-64.lds +1 -0
index 98c7f8e9c5..ee0812aefb 100644
@@ -107,4 +107,5 @@ SECTIONS
 	/DISCARD/ : { *(.plt*) }
 	/DISCARD/ : { *(.interp*) }
 	/DISCARD/ : { *(.gnu*) }
+	/DISCARD/ : { *(.note.gnu.property) }
 }
arch/x86/cpu/u-boot-spl.lds +1 -0
index 4a655bf9b5..346f60bdac 100644
@@ -82,6 +82,7 @@ SECTIONS
 	/DISCARD/ : { *(.plt*) }
 	/DISCARD/ : { *(.interp*) }
 	/DISCARD/ : { *(.gnu*) }
+	/DISCARD/ : { *(.note.gnu.property) }
 
 #if defined(CONFIG_SPL_X86_16BIT_INIT) || defined(CONFIG_TPL_X86_16BIT_INIT)
 	/*
arch/x86/cpu/u-boot.lds +1 -0
index a283c290ee..22fde01e74 100644
@@ -105,6 +105,7 @@ SECTIONS
 	/DISCARD/ : { *(.plt*) }
 	/DISCARD/ : { *(.interp*) }
 	/DISCARD/ : { *(.gnu*) }
+	/DISCARD/ : { *(.note.gnu.property) }
 
 #ifdef CONFIG_X86_16BIT_INIT
 	/*
Signature · 1 line
2.25.1
author
#1 lore raw
Quoted 35 lines · Bin Meng

When switching to kernel.org x86_64 gcc 11.1.0 toolchain, u-boot.rom built from qemu-x86_defconfig no longer boots anymore. Investigation shows that U-Boot fails at a very early stage during the boot process, in fdtdec_prepare_fdt() where fdt_check_header() complains that there is not a valid device tree found at gd->fdt_blob which points to _end. Now _end points to an allocated section .note.gnu.property which of course is wrong.

This issue is however not seen when using the default Ubuntu 20.04 gnu toolchain (gcc 9.3.0 with binutils 2.34). Further investigation shows that it is caused by a behavior change of binutils v2.36 which is part of the kernel.org gcc 11.1.0 toolchain, via the following commit:

939b95c77bf2 ("Linux/x86: Configure gas with --enable-x86-used-note by default")

In fact, there was already a regression bug report [1] for binutils two months ago, but the binutils folks did not think it is a bug :(

To resolve this, there are several options:

* pass -Wa,-mx86-used-note=no to gas
* pass -R .note.gnu.property to objcopy
* discard the section in the linker script

Linux kernel uses the discard way [2], so let's do the same for U-Boot.

[1] https://sourceware.org/bugzilla/show_bug.cgi?id=27753
[2] commit 4caffe6a28d3 ("x86/vdso: Discard .note.gnu.property sections in vDSO")

---

Quoted 8 lines

Changes in v2:
- add the same change to u-boot-spl.lds and u-boot-64.lds

 arch/x86/cpu/u-boot-64.lds  | 1 +
 arch/x86/cpu/u-boot-spl.lds | 1 +
 arch/x86/cpu/u-boot.lds     | 1 +
 3 files changed, 3 insertions(+)

applied to u-boot-x86, thanks!