x86,numa: Pick up reserved memblock from SRAT entries
PATCH 1/1 x86,numa: Pick up reserved memblock from SRAT entries
Spot below error message from 2 sockets server with SGX enabled:
[ 2.264955] sgx: EPC section 0x2000c00000-0x207f7fffff [ 2.269093] sgx: EPC section 0x4000c00000-0x407fffffff [ 2.273242] sgx: [Firmware Bug]: Unable to map EPC section to online node. Fallback to the NUMA node 0.
SGX EPC ranges are reserved(E820) memory managed directly by SGX driver. The second EPC section expected to be bound to NUMA node 1, while phys_to_target_node failed to find a valid online NUMA node from this address range.
Essentially it's not a firmware bug, the root cause is that the second EPC section is arranged at the end of SRAT show as below, thus missed to be picked up by numa_reserved_meminfo. Add additional check for such case.
[ 0.022842] ACPI: SRAT: Node 0 PXM 0 [mem 0x00000000-0x7fffffff] [ 0.022844] ACPI: SRAT: Node 0 PXM 0 [mem 0x100000000-0x207fffffff] [ 0.022846] ACPI: SRAT: Node 1 PXM 1 [mem 0x2080000000-0x407fffffff]
w/o this patch:
crash> numa_meminfonuma_meminfo = $1 = {
nr_blks = 0x2,
blk = {{
start = 0x0,
end = 0x2080000000,
nid = 0x0
}, {
start = 0x2080000000,
end = 0x4000000000,
nid = 0x1
}, {
crash> numa_reserved_meminfo
numa_reserved_meminfo = $2 = {
nr_blks = 0x0,
blk = {{
start = 0x0,
end = 0x0,
nid = 0x0
},w/ this patch:
crash> numa_meminfonuma_meminfo = $1 = {
nr_blks = 0x2,
blk = {{
start = 0x0,
end = 0x2080000000,
nid = 0x0
}, {
start = 0x2080000000,
end = 0x4000000000,
nid = 0x1
},
crash> numa_reserved_meminfo
numa_reserved_meminfo = $2 = {
nr_blks = 0x1,
blk = {{
start = 0x4000000000,
end = 0x4080000000,
nid = 0x1
},Signed-off-by Fan Du <[email protected]>
Reviewed-by Jarkko Sakkinen <[email protected]>
Reviewed-by Dan Williams <[email protected]>
Fixes 5d30f92e7631 ("x86/NUMA: Provide a range-to-target_node lookup facility")
--- arch/x86/mm/numa.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
arch/x86/mm/numa.c +6 -1
@@ -254,7 +254,12 @@ int __init numa_cleanup_meminfo(struct numa_meminfo *mi)/* make sure all non-reserved blocks are inside the limits */ bi->start =max (bi->start, low); - bi->end =min (bi->end, high); + +/* handle reserved memory at the end of the SRAT range */ +if (bi->end > high) { +numa_add_memblk_to (bi->nid, high, bi->end, &numa_reserved_meminfo); + bi->end = high; + }/* and there's no empty block */ if (bi->start >= bi->end)
Signature · 1 line
2.27.0