Skip to contentSkip to conversation

drm/amd/pm: Simplify managed I2C transfer of Aldebaran

PATCH New Luben Tuikov 1 participant 3 messages Jun 28, 2021

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 drm/amd/pm: Simplify managed I2C transfer of Aldebaran

Simplify Aldebaran managed I2C transfer function to correctly play with the upper I2C layers.

This gets it in line with Navi10, Acturus, and Sienna Cichlid.

Cc Alexander Deucher <[email protected]>
Cc Andrey Grodzovsky <[email protected]>
Cc Lijo Lazar <[email protected]>
Cc John Clements <[email protected]>
Cc Hawking Zhang <[email protected]>
---
 .../drm/amd/pm/swsmu/smu13/aldebaran_ppt.c    | 230 +++++-------------
 1 file changed, 55 insertions(+), 175 deletions(-)
drivers/gpu/drm/amd/pm/swsmu/smu13/aldebaran_ppt.c +55 -175
index 9316a726195cc0..f30edf862b86d1 100644
@@ -1425,197 +1425,77 @@ static bool aldebaran_is_dpm_running(struct smu_context *smu)
 	return !!(feature_enabled & SMC_DPM_FEATURE);
 }
 
-static void aldebaran_fill_i2c_req(SwI2cRequest_t  *req, bool write,
-				  uint8_t address, uint32_t numbytes,
-				  uint8_t *data)
-{
-	int i;
-
-	req->I2CcontrollerPort = 0;
-	req->I2CSpeed = 2;
-	req->SlaveAddress = address;
-	req->NumCmds = numbytes;
-
-	for (i = 0; i < numbytes; i++) {
-		SwI2cCmd_t *cmd =  &req->SwI2cCmds[i];
-
-		/* First 2 bytes are always write for lower 2b EEPROM address */
-		if (i < 2)
-			cmd->CmdConfig = CMDCONFIG_READWRITE_MASK;
-		else
-			cmd->CmdConfig = write ? CMDCONFIG_READWRITE_MASK : 0;
-
-
-		/* Add RESTART for read  after address filled */
-		cmd->CmdConfig |= (i == 2 && !write) ? CMDCONFIG_RESTART_MASK : 0;
-
-		/* Add STOP in the end */
-		cmd->CmdConfig |= (i == (numbytes - 1)) ? CMDCONFIG_STOP_MASK : 0;
-
-		/* Fill with data regardless if read or write to simplify code */
-		cmd->ReadWriteData = data[i];
-	}
-}
-
-static int aldebaran_i2c_read_data(struct i2c_adapter *control,
-					       uint8_t address,
-					       uint8_t *data,
-					       uint32_t numbytes)
+static int aldebaran_i2c_xfer(struct i2c_adapter *i2c_adap,
+			      struct i2c_msg *msg, int num_msgs)
 {
-	uint32_t  i, ret = 0;
-	SwI2cRequest_t req;
-	struct amdgpu_device *adev = to_amdgpu_device(control);
+	struct amdgpu_device *adev = to_amdgpu_device(i2c_adap);
 	struct smu_table_context *smu_table = &adev->smu.smu_table;
 	struct smu_table *table = &smu_table->driver_table;
+	SwI2cRequest_t *req, *res = (SwI2cRequest_t *)table->cpu_addr;
+	int i, j, r, c;
+	u16 dir;
 
-	if (numbytes > MAX_SW_I2C_COMMANDS) {
-		dev_err(adev->dev, "numbytes requested %d is over max allowed %d\n",
-			numbytes, MAX_SW_I2C_COMMANDS);
-		return -EINVAL;
-	}
-
-	memset(&req, 0, sizeof(req));
-	aldebaran_fill_i2c_req(&req, false, address, numbytes, data);
-
-	mutex_lock(&adev->smu.mutex);
-	/* Now read data starting with that address */
-	ret = smu_cmn_update_table(&adev->smu, SMU_TABLE_I2C_COMMANDS, 0, &req,
-					true);
-	mutex_unlock(&adev->smu.mutex);
-
-	if (!ret) {
-		SwI2cRequest_t *res = (SwI2cRequest_t *)table->cpu_addr;
-
-		/* Assume SMU  fills res.SwI2cCmds[i].Data with read bytes */
-		for (i = 0; i < numbytes; i++)
-			data[i] = res->SwI2cCmds[i].ReadWriteData;
-
-		dev_dbg(adev->dev, "aldebaran_i2c_read_data, address = %x, bytes = %d, data :",
-				  (uint16_t)address, numbytes);
-
-		print_hex_dump(KERN_DEBUG, "data: ", DUMP_PREFIX_NONE,
-			       8, 1, data, numbytes, false);
-	} else
-		dev_err(adev->dev, "aldebaran_i2c_read_data - error occurred :%x", ret);
+	req = kzalloc(sizeof(*req), GFP_KERNEL);
+	if (!req)
+		return -ENOMEM;
 
-	return ret;
-}
+	req->I2CcontrollerPort = 0;
+	req->I2CSpeed = I2C_SPEED_FAST_400K;
+	req->SlaveAddress = msg[0].addr << 1; /* wants an 8-bit address */
+	dir = msg[0].flags & I2C_M_RD;
+
+	for (c = i = 0; i < num_msgs; i++) {
+		for (j = 0; j < msg[i].len; j++, c++) {
+			SwI2cCmd_t *cmd = &req->SwI2cCmds[c];
+
+			if (!(msg[i].flags & I2C_M_RD)) {
+				/* write */
+				cmd->CmdConfig |= CMDCONFIG_READWRITE_MASK;
+				cmd->ReadWriteData = msg[i].buf[j];
+			}
 
-static int aldebaran_i2c_write_data(struct i2c_adapter *control,
-						uint8_t address,
-						uint8_t *data,
-						uint32_t numbytes)
-{
-	uint32_t ret;
-	SwI2cRequest_t req;
-	struct amdgpu_device *adev = to_amdgpu_device(control);
+			if ((dir ^ msg[i].flags) & I2C_M_RD) {
+				/* The direction changes.
+				 */
+				dir = msg[i].flags & I2C_M_RD;
+				cmd->CmdConfig |= CMDCONFIG_RESTART_MASK;
+			}
 
-	if (numbytes > MAX_SW_I2C_COMMANDS) {
-		dev_err(adev->dev, "numbytes requested %d is over max allowed %d\n",
-			numbytes, MAX_SW_I2C_COMMANDS);
-		return -EINVAL;
+			req->NumCmds++;
+
+			/*
+			 * Insert STOP if we are at the last byte of either last
+			 * message for the transaction or the client explicitly
+			 * requires a STOP at this particular message.
+			 */
+			if ((j == msg[i].len - 1) &&
+			    ((i == num_msgs - 1) || (msg[i].flags & I2C_M_STOP))) {
+				cmd->CmdConfig &= ~CMDCONFIG_RESTART_MASK;
+				cmd->CmdConfig |= CMDCONFIG_STOP_MASK;
+			}
+		}
 	}
-
-	memset(&req, 0, sizeof(req));
-	aldebaran_fill_i2c_req(&req, true, address, numbytes, data);
-
 	mutex_lock(&adev->smu.mutex);
-	ret = smu_cmn_update_table(&adev->smu, SMU_TABLE_I2C_COMMANDS, 0, &req, true);
+	r = smu_cmn_update_table(&adev->smu, SMU_TABLE_I2C_COMMANDS, 0, req, true);
 	mutex_unlock(&adev->smu.mutex);
+	if (r)
+		goto fail;
 
-	if (!ret) {
-		dev_dbg(adev->dev, "aldebaran_i2c_write(), address = %x, bytes = %d , data: ",
-					 (uint16_t)address, numbytes);
-
-		print_hex_dump(KERN_DEBUG, "data: ", DUMP_PREFIX_NONE,
-			       8, 1, data, numbytes, false);
-		/*
-		 * According to EEPROM spec there is a MAX of 10 ms required for
-		 * EEPROM to flush internal RX buffer after STOP was issued at the
-		 * end of write transaction. During this time the EEPROM will not be
-		 * responsive to any more commands - so wait a bit more.
-		 */
-		msleep(10);
-
-	} else
-		dev_err(adev->dev, "aldebaran_i2c_write- error occurred :%x", ret);
-
-	return ret;
-}
-
-static int aldebaran_i2c_xfer(struct i2c_adapter *i2c_adap,
-			      struct i2c_msg *msgs, int num)
-{
-	uint32_t  i, j, ret, data_size, data_chunk_size, next_eeprom_addr = 0;
-	uint8_t *data_ptr, data_chunk[MAX_SW_I2C_COMMANDS] = { 0 };
-
-	for (i = 0; i < num; i++) {
-		/*
-		 * SMU interface allows at most MAX_SW_I2C_COMMANDS bytes of data at
-		 * once and hence the data needs to be spliced into chunks and sent each
-		 * chunk separately
-		 */
-		data_size = msgs[i].len - 2;
-		data_chunk_size = MAX_SW_I2C_COMMANDS - 2;
-		next_eeprom_addr = (msgs[i].buf[0] << 8 & 0xff00) | (msgs[i].buf[1] & 0xff);
-		data_ptr = msgs[i].buf + 2;
-
-		for (j = 0; j < data_size / data_chunk_size; j++) {
-			/* Insert the EEPROM dest addess, bits 0-15 */
-			data_chunk[0] = ((next_eeprom_addr >> 8) & 0xff);
-			data_chunk[1] = (next_eeprom_addr & 0xff);
-
-			if (msgs[i].flags & I2C_M_RD) {
-				ret = aldebaran_i2c_read_data(i2c_adap,
-							     (uint8_t)msgs[i].addr,
-							     data_chunk, MAX_SW_I2C_COMMANDS);
-
-				memcpy(data_ptr, data_chunk + 2, data_chunk_size);
-			} else {
-
-				memcpy(data_chunk + 2, data_ptr, data_chunk_size);
-
-				ret = aldebaran_i2c_write_data(i2c_adap,
-							      (uint8_t)msgs[i].addr,
-							      data_chunk, MAX_SW_I2C_COMMANDS);
-			}
-
-			if (ret) {
-				num = -EIO;
-				goto fail;
-			}
-
-			next_eeprom_addr += data_chunk_size;
-			data_ptr += data_chunk_size;
+	for (c = i = 0; i < num_msgs; i++) {
+		if (!(msg[i].flags & I2C_M_RD)) {
+			c += msg[i].len;
+			continue;
 		}
+		for (j = 0; j < msg[i].len; j++, c++) {
+			SwI2cCmd_t *cmd = &res->SwI2cCmds[c];
 
-		if (data_size % data_chunk_size) {
-			data_chunk[0] = ((next_eeprom_addr >> 8) & 0xff);
-			data_chunk[1] = (next_eeprom_addr & 0xff);
-
-			if (msgs[i].flags & I2C_M_RD) {
-				ret = aldebaran_i2c_read_data(i2c_adap,
-							     (uint8_t)msgs[i].addr,
-							     data_chunk, (data_size % data_chunk_size) + 2);
-
-				memcpy(data_ptr, data_chunk + 2, data_size % data_chunk_size);
-			} else {
-				memcpy(data_chunk + 2, data_ptr, data_size % data_chunk_size);
-
-				ret = aldebaran_i2c_write_data(i2c_adap,
-							      (uint8_t)msgs[i].addr,
-							      data_chunk, (data_size % data_chunk_size) + 2);
-			}
-
-			if (ret) {
-				num = -EIO;
-				goto fail;
-			}
+			msg[i].buf[j] = cmd->ReadWriteData;
 		}
 	}
-
+	r = num_msgs;
 fail:
-	return num;
+	kfree(req);
+	return r;
 }
 
 static u32 aldebaran_i2c_func(struct i2c_adapter *adap)
Signature · 6 lines
2.32.0

_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
#1 lore raw

PATCH 2/3 drm/amd/pm: Fix I2C controller port setting of Arcturus

Fix controller port setting of Arcturus from 1
(incorrect) to 0 (correct).

This fixes a previous rework commit which
introduced this typo.

Cc Alexander Deucher <[email protected]>
Fixes 10e547e01291e1 ("drm/amdgpu/pm: rework i2c xfers on arcturus (v4)")
---
 drivers/gpu/drm/amd/pm/swsmu/smu11/arcturus_ppt.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/amd/pm/swsmu/smu11/arcturus_ppt.c +1 -1
index dc884b719717ad..b1adbe17b6c2d4 100644
@@ -1950,7 +1950,7 @@ static int arcturus_i2c_xfer(struct i2c_adapter *i2c_adap,
 	if (!req)
 		return -ENOMEM;
 
-	req->I2CcontrollerPort = 1;
+	req->I2CcontrollerPort = 0;
 	req->I2CSpeed = I2C_SPEED_FAST_400K;
 	req->SlaveAddress = msg[0].addr << 1; /* wants an 8-bit address */
 	dir = msg[0].flags & I2C_M_RD;
Signature · 6 lines
2.32.0

_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx
#2 lore raw

PATCH 3/3 drm/amd/pm: Fix I2C controller port setting of Navi10

In reply to Luben Tuikov

Fix controller port setting of Navi10 from 1
(incorrect) to 0 (correct).

This fixes a previous rework commit which
introduced this typo.

Cc Alexander Deucher <[email protected]>
Fixes f3be7dda30f4b0 ("drm/amdgpu/pm: add smu i2c implementation for navi1x (v4)")
---
 drivers/gpu/drm/amd/pm/swsmu/smu11/navi10_ppt.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/amd/pm/swsmu/smu11/navi10_ppt.c +1 -1
index 205dc2e56ab199..36264b78199620 100644
@@ -2749,7 +2749,7 @@ static int navi10_i2c_xfer(struct i2c_adapter *i2c_adap,
 	if (!req)
 		return -ENOMEM;
 
-	req->I2CcontrollerPort = 1;
+	req->I2CcontrollerPort = 0;
 	req->I2CSpeed = I2C_SPEED_FAST_400K;
 	req->SlaveAddress = msg[0].addr << 1; /* wants an 8-bit address */
 	dir = msg[0].flags & I2C_M_RD;
Signature · 6 lines
2.32.0

_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx