sysinfo: rcar3: Add Renesas R-Car Gen3 sysinfo driver
PATCH 1/1 sysinfo: rcar3: Add Renesas R-Car Gen3 sysinfo driver
The Renesas R-Car Gen3 development kits contain board ID EEPROM. This driver parses out the board ID and revision out of that EEPROM and exports it e.g. for the board-info print on boot.
Signed-off-by Marek Vasut <[email protected]>
Cc Sean Anderson <[email protected]>
Cc Simon Glass <[email protected]>
--- drivers/sysinfo/Kconfig | 7 ++ drivers/sysinfo/Makefile | 1 + drivers/sysinfo/rcar3.c | 197 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 205 insertions(+) create mode 100644 drivers/sysinfo/rcar3.c
drivers/sysinfo/Kconfig +7 -0
@@ -17,6 +17,13 @@ config SYSINFO_GAZERBEAM help Support querying device information for the gdsys Gazerbeam board. +config SYSINFO_RCAR3 + bool "Enable sysinfo driver for the Renesas R-Car Gen3" + depends on RCAR_GEN3 && I2C_EEPROM + default y if RCAR_GEN3 + help + Support querying SoC version information for Renesas R-Car Gen3. + config SYSINFO_SANDBOX bool "Enable sysinfo driver for the Sandbox board" help
drivers/sysinfo/Makefile +1 -0
@@ -5,5 +5,6 @@ obj-y += sysinfo-uclass.o obj-$(CONFIG_SYSINFO_GAZERBEAM) += gazerbeam.o obj-$(CONFIG_SYSINFO_GPIO) += gpio.o +obj-$(CONFIG_SYSINFO_RCAR3) += rcar3.o obj-$(CONFIG_SYSINFO_SANDBOX) += sandbox.o obj-$(CONFIG_SYSINFO_SMBIOS) += smbios.o
drivers/sysinfo/rcar3.c new file +197 -0
197 lines not on this page · raw message
Signature · 1 line
2.30.2
Hi Marek,
Quoted 8 lines · Marek Vasut
The Renesas R-Car Gen3 development kits contain board ID EEPROM. This driver parses out the board ID and revision out of that EEPROM and exports it e.g. for the board-info print on boot.
Signed-off-by Marek Vasut <[email protected]>Cc Sean Anderson <[email protected]>Cc Simon Glass <[email protected]>
Quoted 7 lines
--- drivers/sysinfo/Kconfig | 7 ++ drivers/sysinfo/Makefile | 1 + drivers/sysinfo/rcar3.c | 197 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 205 insertions(+) create mode 100644 drivers/sysinfo/rcar3.c
Reviewed-by Simon Glass <[email protected]>
Quoted 75 lines
drivers/sysinfo/Kconfig +7
-0@@ -17,6 +17,13 @@ config SYSINFO_GAZERBEAM help Support querying device information for the gdsys Gazerbeam board. +config SYSINFO_RCAR3 + bool "Enable sysinfo driver for the Renesas R-Car Gen3" + depends on RCAR_GEN3 && I2C_EEPROM + default y if RCAR_GEN3 + help + Support querying SoC version information for Renesas R-Car Gen3. + config SYSINFO_SANDBOX bool "Enable sysinfo driver for the Sandbox board" helpdrivers/sysinfo/Makefile +1
-0@@ -5,5 +5,6 @@ obj-y += sysinfo-uclass.o obj-$(CONFIG_SYSINFO_GAZERBEAM) += gazerbeam.o obj-$(CONFIG_SYSINFO_GPIO) += gpio.o +obj-$(CONFIG_SYSINFO_RCAR3) += rcar3.o obj-$(CONFIG_SYSINFO_SANDBOX) += sandbox.o obj-$(CONFIG_SYSINFO_SMBIOS) += smbios.odrivers/sysinfo/rcar3.c new file +40
-0@@ -0,0 +1,197 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2021 Marek Vasut <[email protected]> +*/ + +#include <common.h> +#include <dm.h> +#include <i2c_eeprom.h> +#include <log.h> +#include <sysinfo.h> + +#define BOARD_CODE_MASK 0xF8 +#define BOARD_REV_MASK 0x07 +#define BOARD_CODE_SHIFT 0x03 + +#define BOARD_SALVATOR_X 0x0 +#define BOARD_KRIEK 0x1 +#define BOARD_STARTER_KIT 0x2 +#define BOARD_SALVATOR_XS 0x4 +#define BOARD_EBISU 0x8 +#define BOARD_STARTER_KIT_PRE 0xB +#define BOARD_EBISU_4D 0xD +#define BOARD_DRAAK 0xE +#define BOARD_EAGLE 0xF + +/** +* struct sysinfo_rcar_priv - sysinfo private data +* @boardname: board model and revision +* @val: board ID value from eeprom +*/ +struct sysinfo_rcar_priv { +char boardmodel[64 ]; +u8 val; +}; + +static int sysinfo_rcar_detect (struct udevice *dev) +{ +struct sysinfo_rcar_priv *priv =dev_get_priv (dev); + +return priv->val ==0xff ;
drivers/sysinfo/rcar3.c line 50
Quoted 10 lines
drivers/sysinfo/rcar3.c new file +10
-0+} + +static int sysinfo_rcar_get_str (struct udevice *dev,int id,size_t size,char *val) +{ +struct sysinfo_rcar_priv *priv =dev_get_priv (dev); + +switch (id) { +case SYSINFO_ID_BOARD_MODEL : +strncpy (val, priv->boardmodel, size); + val[size -1 ] ='\0' ;
strlcpy()
[...\
You might consider using
return log_msg_ret("xxx", ret)
for errors.
Regards,
Simon