spi: Make of_register_spi_device also set the fwnode
Subsystems (14)
Sasha Levin
maintainerPATCH 1/50 spi: Make of_register_spi_device also set the fwnode
From: Charles Keepax <[email protected]>
[ Upstream commit 0e793ba77c18382f08e440260fe72bc6fce2a3cb ]
Currently, the SPI core doesn't set the struct device fwnode pointer when it creates a new SPI device. This means when the device is registered the fwnode is NULL and the check in device_add which sets the fwnode->dev pointer is skipped. This wasn't previously an issue, however these two patches:
commit 4731210c09f5 ("gpiolib: Bind gpio_device to a driver to enable fw_devlink=on by default")
commit ced2af419528 ("gpiolib: Don't probe gpio_device if it's not the primary device")
Added some code to the GPIO core which relies on using that fwnode->dev pointer to determine if a driver is bound to the fwnode and if not bind a stub GPIO driver. This means the GPIO providers behind SPI will get both the expected driver and this stub driver causing the stub driver to fail if it attempts to request any pin configuration. For example on my system:
madera-pinctrl madera-pinctrl: pin gpio5 already requested by madera-pinctrl; cannot claim for gpiochip3 madera-pinctrl madera-pinctrl: pin-4 (gpiochip3) status -22
madera-pinctrl madera-pinctrl: could not request pin 4 (gpio5) from group aif1 on device madera-pinctrl gpio_stub_drv gpiochip3: Error applying setting, reverse things backgpio_stub_drv: probe of gpiochip3 failed with error -22
The firmware node on the device created by the GPIO framework is set through the of_node pointer hence things generally actually work, however that fwnode->dev is never set, as the check was skipped at device_add time. This fix appears to match how the I2C subsystem handles the same situation.
--- drivers/spi/spi.c | 1 + 1 file changed, 1 insertion(+)
drivers/spi/spi.c +1 -0
@@ -1849,6 +1849,7 @@ of_register_spi_device(struct spi_controller *ctlr, struct device_node *nc)/* Store a pointer to the node in the device structure */ of_node_get (nc); spi->dev.of_node = nc; + spi->dev.fwnode =of_fwnode_handle (nc);/* Register the new device */ rc =spi_add_device (spi);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 2/50 media: mdk-mdp: fix pm_runtime_get_sync() usage count
From: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit d07bb9702cf5f5ccf3fb661e6cab54bbc33cd23f ]
The pm_runtime_get_sync() internally increments thedev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
While here, fix the return contition of mtk_mdp_m2m_start_streaming(), as it doesn't make any sense to return 0 if the PM runtime failed to resume.
--- drivers/media/platform/mtk-mdp/mtk_mdp_m2m.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/media/platform/mtk-mdp/mtk_mdp_m2m.c +3 -3
@@ -402,12 +402,12 @@ static int mtk_mdp_m2m_start_streaming(struct vb2_queue *q, unsigned int count)struct mtk_mdp_ctx *ctx = q->drv_priv;int ret; - ret =pm_runtime_get_sync (&ctx->mdp_dev->pdev->dev); + ret =pm_runtime_resume_and_get (&ctx->mdp_dev->pdev->dev);if (ret <0 ) -mtk_mdp_dbg (1 ,"[%d] pm_runtime_get_sync failed:%d" , +mtk_mdp_dbg (1 ,"[%d] pm_runtime_resume_and_get failed:%d" , ctx->id, ret); -return 0 ; +return ret; } static void *mtk_mdp_m2m_buf_remove(struct mtk_mdp_ctx *ctx,
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 3/50 media: s5p: fix pm_runtime_get_sync() usage count
In reply to Sasha LevinFrom: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit fdc34e82c0f968ac4c157bd3d8c299ebc24c9c63 ]
The pm_runtime_get_sync() internally increments thedev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
While here, check if the PM runtime error was caught at s5p_cec_adap_enable().
--- drivers/media/platform/s5p-cec/s5p_cec.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/media/platform/s5p-cec/s5p_cec.c +4 -1
@@ -35,10 +35,13 @@ MODULE_PARM_DESC(debug, "debug level (0-2)");static int s5p_cec_adap_enable (struct cec_adapter *adap,bool enable) { +int ret;struct s5p_cec_dev *cec =cec_get_drvdata (adap);if (enable) { -pm_runtime_get_sync (cec->dev); + ret =pm_runtime_resume_and_get (cec->dev); +if (ret <0 ) +return ret;s5p_cec_reset (cec);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 4/50 media: sh_vou: fix pm_runtime_get_sync() usage count
In reply to Sasha LevinFrom: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit 6e8b1526db164c9d4b9dacfb9bc48e365d7c4860 ]
The pm_runtime_get_sync() internally increments thedev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
While here, check if the PM runtime error was caught at open time.
--- drivers/media/platform/sh_vou.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/media/platform/sh_vou.c +5 -1
@@ -1133,7 +1133,11 @@ static int sh_vou_open(struct file *file)if (v4l2_fh_is_singular_file (file) && vou_dev->status ==SH_VOU_INITIALISING ) {/* First open */ -pm_runtime_get_sync (vou_dev->v4l2_dev.dev); + err =pm_runtime_resume_and_get (vou_dev->v4l2_dev.dev); +if (err <0 ) { +v4l2_fh_release (file); + goto done_open; + } err =sh_vou_hw_init (vou_dev);if (err <0 ) {pm_runtime_put (vou_dev->v4l2_dev.dev);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 5/50 media: mtk-vcodec: fix PM runtime get logic
In reply to Sasha LevinFrom: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit 908711f542c17fe61e5d653da1beb8e5ab5c7b50 ]
Currently, the driver just assumes that PM runtime logic succeded resuming the device.
That may not be the case, as pm_runtime_get_sync() can fail (but keeping the usage count incremented).
Replace the code to use pm_runtime_resume_and_get(), and letting it return the error code.
This way, if mtk_vcodec_dec_pw_on() fails, the logic under fops_vcodec_open() will do the right thing and return an error, instead of just assuming that the device is ready to be used.
--- drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_drv.c | 4 +++- drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_pm.c | 8 +++++--- drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_pm.h | 2 +- 3 files changed, 9 insertions(+), 5 deletions(-)
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_drv.c +3 -1
@@ -142,7 +142,9 @@ static int fops_vcodec_open(struct file *file)mtk_vcodec_dec_set_default_params (ctx);if (v4l2_fh_is_singular (&ctx->fh)) { -mtk_vcodec_dec_pw_on (&dev->pm); + ret =mtk_vcodec_dec_pw_on (&dev->pm); +if (ret <0 ) + goto err_load_fw;/* * vpu_load_firmware checks if it was loaded already and * does nothing in that case
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_pm.c +5 -3
@@ -89,13 +89,15 @@ void mtk_vcodec_release_dec_pm(struct mtk_vcodec_dev *dev)put_device (dev->pm.larbvdec); } -void mtk_vcodec_dec_pw_on (struct mtk_vcodec_pm *pm) +int mtk_vcodec_dec_pw_on (struct mtk_vcodec_pm *pm) {int ret; - ret =pm_runtime_get_sync (pm->dev); + ret =pm_runtime_resume_and_get (pm->dev);if (ret) -mtk_v4l2_err ("pm_runtime_get_sync fail %d" , ret); +mtk_v4l2_err ("pm_runtime_resume_and_get fail %d" , ret); + +return ret; }void mtk_vcodec_dec_pw_off (struct mtk_vcodec_pm *pm)
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_pm.h +1 -1
@@ -12,7 +12,7 @@int mtk_vcodec_init_dec_pm (struct mtk_vcodec_dev *dev);void mtk_vcodec_release_dec_pm (struct mtk_vcodec_dev *dev); -void mtk_vcodec_dec_pw_on (struct mtk_vcodec_pm *pm); +int mtk_vcodec_dec_pw_on (struct mtk_vcodec_pm *pm);void mtk_vcodec_dec_pw_off (struct mtk_vcodec_pm *pm);void mtk_vcodec_dec_clock_on (struct mtk_vcodec_pm *pm);void mtk_vcodec_dec_clock_off (struct mtk_vcodec_pm *pm);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 6/50 media: s5p-jpeg: fix pm_runtime_get_sync() usage count
In reply to Sasha LevinFrom: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit 10343de268d10cf07b092b8b525e12ad558ead77 ]
The pm_runtime_get_sync() internally increments thedev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
As a plus, pm_runtime_resume_and_get() doesn't return positive numbers, so the return code validation can be removed.
--- drivers/media/platform/s5p-jpeg/jpeg-core.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/media/platform/s5p-jpeg/jpeg-core.c +1 -4
@@ -2579,11 +2579,8 @@ static void s5p_jpeg_buf_queue(struct vb2_buffer *vb)static int s5p_jpeg_start_streaming (struct vb2_queue *q,unsigned int count) {struct s5p_jpeg_ctx *ctx =vb2_get_drv_priv (q); -int ret; - - ret =pm_runtime_get_sync (ctx->jpeg->dev); -return ret >0 ?0 : ret; +return pm_runtime_resume_and_get (ctx->jpeg->dev); }static void s5p_jpeg_stop_streaming (struct vb2_queue *q)
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 7/50 media: sti/bdisp: fix pm_runtime_get_sync() usage count
In reply to Sasha LevinFrom: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit c44eac5b72e23c31eefc0e10a71d9650036b8341 ]
The pm_runtime_get_sync() internally increments the dev->power.usage_count without decrementing it, even on errors.
The bdisp_start_streaming() doesn't take it into account, which would unbalance PM usage counter at bdisp_stop_streaming().
The logic at bdisp_probe() is correct, but the best is to use the same call along the driver.
So, replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
--- drivers/media/platform/sti/bdisp/bdisp-v4l2.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/media/platform/sti/bdisp/bdisp-v4l2.c +4 -3
@@ -499,7 +499,7 @@ static int bdisp_start_streaming(struct vb2_queue *q, unsigned int count) {struct bdisp_ctx *ctx = q->drv_priv;struct vb2_v4l2_buffer *buf; -int ret =pm_runtime_get_sync (ctx->bdisp_dev->dev); +int ret =pm_runtime_resume_and_get (ctx->bdisp_dev->dev);if (ret <0 ) {dev_err (ctx->bdisp_dev->dev,"failed to set runtime PM\n" );
@@ -1364,10 +1364,10 @@ static int bdisp_probe(struct platform_device *pdev)/* Power management */ pm_runtime_enable (dev); - ret =pm_runtime_get_sync (dev); + ret =pm_runtime_resume_and_get (dev);if (ret <0 ) {dev_err (dev,"failed to set PM\n" ); - goto err_pm; + goto err_remove; }/* Filters */
@@ -1395,6 +1395,7 @@ static int bdisp_probe(struct platform_device *pdev)bdisp_hw_free_filters (bdisp->dev); err_pm:pm_runtime_put (dev); +err_remove:bdisp_debugfs_remove (bdisp); err_v4l2:v4l2_device_unregister (&bdisp->v4l2_dev);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 8/50 media: exynos-gsc: fix pm_runtime_get_sync() usage count
In reply to Sasha LevinFrom: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit 59087b66ea6730c130c57d23bd9fd139b78c1ba5 ]
The pm_runtime_get_sync() internally increments thedev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
As a bonus, as pm_runtime_get_sync() always return 0 on success, the logic can be simplified.
--- drivers/media/platform/exynos-gsc/gsc-m2m.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)
drivers/media/platform/exynos-gsc/gsc-m2m.c +1 -3
@@ -56,10 +56,8 @@ static void __gsc_m2m_job_abort(struct gsc_ctx *ctx)static int gsc_m2m_start_streaming (struct vb2_queue *q,unsigned int count) {struct gsc_ctx *ctx = q->drv_priv; -int ret; - ret =pm_runtime_get_sync (&ctx->gsc_dev->pdev->dev); -return ret >0 ?0 : ret; +return pm_runtime_resume_and_get (&ctx->gsc_dev->pdev->dev); }static void __gsc_m2m_cleanup_queue (struct gsc_ctx *ctx)
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 9/50 spi: spi-loopback-test: Fix 'tx_buf' might be 'rx_buf'
In reply to Sasha LevinFrom: Jay Fang <[email protected]>
[ Upstream commit 9e37a3ab0627011fb63875e9a93094b6fc8ddf48 ]
In function 'spi_test_run_iter': Value 'tx_buf' might be 'rx_buf'.
--- drivers/spi/spi-loopback-test.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-loopback-test.c +1 -1
@@ -868,7 +868,7 @@ static int spi_test_run_iter(struct spi_device *spi, test.transfers[i].len = len;if (test.transfers[i].tx_buf) test.transfers[i].tx_buf += tx_off; -if (test.transfers[i].tx_buf) +if (test.transfers[i].rx_buf) test.transfers[i].rx_buf += rx_off; }
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 10/50 spi: spi-topcliff-pch: Fix potential double free in pch_spi_process_messages()
In reply to Sasha LevinFrom: Jay Fang <[email protected]>
[ Upstream commit 026a1dc1af52742c5897e64a3431445371a71871 ]
pch_spi_set_tx() frees data->pkt_tx_buff on failure of kzalloc() for data->pkt_rx_buff, but its caller, pch_spi_process_messages(), will free data->pkt_tx_buff again. Set data->pkt_tx_buff to NULL after kfree() to avoid double free.
--- drivers/spi/spi-topcliff-pch.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/spi/spi-topcliff-pch.c +3 -1
@@ -576,8 +576,10 @@ static void pch_spi_set_tx(struct pch_spi_data *data, int *bpw) data->pkt_tx_buff =kzalloc (size,GFP_KERNEL );if (data->pkt_tx_buff !=NULL ) { data->pkt_rx_buff =kzalloc (size,GFP_KERNEL ); -if (!data->pkt_rx_buff) +if (!data->pkt_rx_buff) {kfree (data->pkt_tx_buff); + data->pkt_tx_buff =NULL ; + } }if (!data->pkt_rx_buff) {
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 11/50 spi: omap-100k: Fix the length judgment problem
In reply to Sasha LevinFrom: Tian Tao <[email protected]>
[ Upstream commit e7a1a3abea373e41ba7dfe0fbc93cb79b6a3a529 ]
word_len should be checked in the omap1_spi100k_setup_transfer function to see if it exceeds 32.
--- drivers/spi/spi-omap-100k.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-omap-100k.c +1 -1
@@ -242,7 +242,7 @@ static int omap1_spi100k_setup_transfer(struct spi_device *spi,else word_len = spi->bits_per_word; -if (spi->bits_per_word >32 ) +if (word_len >32 )return -EINVAL ; cs->word_len = word_len;
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 12/50 regulator: uniphier: Add missing MODULE_DEVICE_TABLE
In reply to Sasha LevinFrom: Zou Wei <[email protected]>
[ Upstream commit d019f38a1af3c6015cde6a47951a3ec43beeed80 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates correct modalias for automatic loading of this driver when it is built as an external module.
--- drivers/regulator/uniphier-regulator.c | 1 + 1 file changed, 1 insertion(+)
drivers/regulator/uniphier-regulator.c +1 -0
@@ -203,6 +203,7 @@ static const struct of_device_id uniphier_regulator_match[] = { }, { /* Sentinel */ }, }; +MODULE_DEVICE_TABLE (of, uniphier_regulator_match);static struct platform_driver uniphier_regulator_driver = { .probe = uniphier_regulator_probe,
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 13/50 hwrng: exynos - Fix runtime PM imbalance on error
In reply to Sasha LevinFrom: Łukasz Stelmach <[email protected]>
[ Upstream commit 0cdbabf8bb7a6147f5adf37dbc251e92a1bbc2c7 ]
pm_runtime_resume_and_get() wraps around pm_runtime_get_sync() and decrements the runtime PM usage counter in case the latter function fails and keeps the counter balanced.
--- drivers/char/hw_random/exynos-trng.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/char/hw_random/exynos-trng.c +2 -2
@@ -134,7 +134,7 @@ static int exynos_trng_probe(struct platform_device *pdev)return PTR_ERR (trng->mem);pm_runtime_enable (&pdev->dev); - ret =pm_runtime_get_sync (&pdev->dev); + ret =pm_runtime_resume_and_get (&pdev->dev);if (ret <0 ) {dev_err (&pdev->dev,"Could not get runtime PM.\n" ); goto err_pm_get;
@@ -167,7 +167,7 @@ static int exynos_trng_probe(struct platform_device *pdev)clk_disable_unprepare (trng->clk); err_clock: -pm_runtime_put_sync (&pdev->dev); +pm_runtime_put_noidle (&pdev->dev); err_pm_get:pm_runtime_disable (&pdev->dev);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 14/50 crypto: nx - add missing MODULE_DEVICE_TABLE
In reply to Sasha LevinFrom: Bixuan Cui <[email protected]>
[ Upstream commit 06676aa1f455c74e3ad1624cea3acb9ed2ef71ae ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates correct modalias for automatic loading of this driver when it is built as an external module.
--- drivers/crypto/nx/nx-842-pseries.c | 1 + 1 file changed, 1 insertion(+)
drivers/crypto/nx/nx-842-pseries.c +1 -0
@@ -1071,6 +1071,7 @@ static const struct vio_device_id nx842_vio_driver_ids[] = { {"ibm,compression-v1", "ibm,compression"}, {"", ""}, }; +MODULE_DEVICE_TABLE (vio, nx842_vio_driver_ids);static struct vio_driver nx842_vio_driver = { .name = KBUILD_MODNAME,
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 15/50 media: sti: fix obj-$(config) targets
In reply to Sasha LevinFrom: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit 56c1f0876293888f686e31278d183d4af2cac3c3 ]
The right thing to do is to add a new object to the building system when a certain config option is selected, and *not* override them.
So, fix obj-$(config) logic at sti makefiles, using "+=", instead of ":=".
--- drivers/media/platform/sti/bdisp/Makefile | 2 +- drivers/media/platform/sti/delta/Makefile | 2 +- drivers/media/platform/sti/hva/Makefile | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-)
drivers/media/platform/sti/bdisp/Makefile +1 -1
@@ -1,4 +1,4 @@ # SPDX-License-Identifier: GPL-2.0-only -obj-$(CONFIG_VIDEO_STI_BDISP) := bdisp.o +obj-$(CONFIG_VIDEO_STI_BDISP) += bdisp.o bdisp-objs := bdisp-v4l2.o bdisp-hw.o bdisp-debug.o
drivers/media/platform/sti/delta/Makefile +1 -1
@@ -1,5 +1,5 @@ # SPDX-License-Identifier: GPL-2.0-only -obj-$(CONFIG_VIDEO_STI_DELTA_DRIVER) := st-delta.o +obj-$(CONFIG_VIDEO_STI_DELTA_DRIVER) += st-delta.o st-delta-y := delta-v4l2.o delta-mem.o delta-ipc.o delta-debug.o # MJPEG support
drivers/media/platform/sti/hva/Makefile +1 -1
@@ -1,4 +1,4 @@ # SPDX-License-Identifier: GPL-2.0-only -obj-$(CONFIG_VIDEO_STI_HVA) := st-hva.o +obj-$(CONFIG_VIDEO_STI_HVA) += st-hva.o st-hva-y := hva-v4l2.o hva-hw.o hva-mem.o hva-h264.o st-hva-$(CONFIG_VIDEO_STI_HVA_DEBUGFS) += hva-debugfs.o
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 16/50 media: cpia2: fix memory leak in cpia2_usb_probe
In reply to Sasha LevinFrom: Pavel Skripkin <[email protected]>
[ Upstream commit be8656e62e9e791837b606a027802b504a945c97 ]
syzbot reported leak in cpia2 usb driver. The problem was in invalid error handling.
v4l2_device_register() is called in cpia2_init_camera_struct(), but all error cases after cpia2_init_camera_struct() did not call the v4l2_device_unregister()
--- drivers/media/usb/cpia2/cpia2.h | 1 + drivers/media/usb/cpia2/cpia2_core.c | 12 ++++++++++++ drivers/media/usb/cpia2/cpia2_usb.c | 13 +++++++------ 3 files changed, 20 insertions(+), 6 deletions(-)
drivers/media/usb/cpia2/cpia2.h +1 -0
@@ -429,6 +429,7 @@ int cpia2_send_command(struct camera_data *cam, struct cpia2_command *cmd);int cpia2_do_command (struct camera_data *cam,unsigned int command,unsigned char direction,unsigned char param); +void cpia2_deinit_camera_struct (struct camera_data *cam,struct usb_interface *intf);struct camera_data *cpia2_init_camera_struct (struct usb_interface *intf);int cpia2_init_camera (struct camera_data *cam);int cpia2_allocate_buffers (struct camera_data *cam);
drivers/media/usb/cpia2/cpia2_core.c +12 -0
@@ -2163,6 +2163,18 @@ static void reset_camera_struct(struct camera_data *cam) cam->height = cam->params.roi.height; } +/****************************************************************************** +* +* cpia2_init_camera_struct +* +* Deinitialize camera struct +*****************************************************************************/ +void cpia2_deinit_camera_struct (struct camera_data *cam,struct usb_interface *intf) +{ +v4l2_device_unregister (&cam->v4l2_dev); +kfree (cam); +} +/****************************************************************************** * * cpia2_init_camera_struct
drivers/media/usb/cpia2/cpia2_usb.c +7 -6
@@ -844,15 +844,13 @@ static int cpia2_usb_probe(struct usb_interface *intf, ret =set_alternate (cam,USBIF_CMDONLY );if (ret <0 ) {ERR ("%s: usb_set_interface error (ret = %d)\n" , __func__, ret); -kfree (cam); -return ret; + goto alt_err; }if ((ret =cpia2_init_camera (cam)) <0 ) {ERR ("%s: failed to initialize cpia2 camera (ret = %d)\n" , __func__, ret); -kfree (cam); -return ret; + goto alt_err; } LOG(" CPiA Version: %d.%02d (%d.%d)\n", cam->params.version.firmware_revision_hi,
@@ -872,11 +870,14 @@ static int cpia2_usb_probe(struct usb_interface *intf, ret =cpia2_register_camera (cam);if (ret <0 ) {ERR ("%s: Failed to register cpia2 camera (ret = %d)\n" , __func__, ret); -kfree (cam); -return ret; + goto alt_err; }return 0 ; + +alt_err: +cpia2_deinit_camera_struct (cam, intf); +return ret; }/******************************************************************************
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 17/50 media: cobalt: fix race condition in setting HPD
In reply to Sasha LevinFrom: Hans Verkuil <[email protected]>
[ Upstream commit 3d37ef41bed0854805ab9af22c422267510e1344 ]
The cobalt_s_bit_sysctrl reads the old register value over PCI, then changes a bit and sets writes the new value to the register.
This is used among other things for setting the HPD output pin.
But if the HPD is changed for multiple inputs at the same time, then this causes a race condition where a stale value is read.
Serialize this function with a mutex.
--- drivers/media/pci/cobalt/cobalt-driver.c | 1 + drivers/media/pci/cobalt/cobalt-driver.h | 7 ++++++- 2 files changed, 7 insertions(+), 1 deletion(-)
drivers/media/pci/cobalt/cobalt-driver.c +1 -0
@@ -667,6 +667,7 @@ static int cobalt_probe(struct pci_dev *pci_dev,return -ENOMEM ; cobalt->pci_dev = pci_dev; cobalt->instance = i; +mutex_init (&cobalt->pci_lock); retval =v4l2_device_register (&pci_dev->dev, &cobalt->v4l2_dev);if (retval) {
drivers/media/pci/cobalt/cobalt-driver.h +6 -1
@@ -251,6 +251,8 @@ struct cobalt {int instance;struct pci_dev *pci_dev;struct v4l2_device v4l2_dev; +/* serialize PCI access in cobalt_s_bit_sysctrl() */ +struct mutex pci_lock;void __iomem *bar0, *bar1;
@@ -320,10 +322,13 @@ static inline u32 cobalt_g_sysctrl(struct cobalt *cobalt)static inline void cobalt_s_bit_sysctrl (struct cobalt *cobalt,int bit,int val) { -u32 ctrl =cobalt_read_bar1 (cobalt,COBALT_SYS_CTRL_BASE ); +u32 ctrl; +mutex_lock (&cobalt->pci_lock); + ctrl =cobalt_read_bar1 (cobalt,COBALT_SYS_CTRL_BASE );cobalt_write_bar1 (cobalt,COBALT_SYS_CTRL_BASE , (ctrl & ~(1UL << bit)) | (val << bit)); +mutex_unlock (&cobalt->pci_lock); }static inline u32 cobalt_g_sysstat (struct cobalt *cobalt)
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 18/50 media: pvrusb2: fix warning in pvr2_i2c_core_done
In reply to Sasha LevinFrom: Anirudh Rayabharam <[email protected]>
[ Upstream commit f8194e5e63fdcb349e8da9eef9e574d5b1d687cb ]
syzbot has reported the following warning in pvr2_i2c_done:
sysfs group 'power' not found for kobject '1-0043'
When the device is disconnected (pvr_hdw_disconnect), the i2c adapter is not unregistered along with the USB and v4l2 teardown. As part of the USB device disconnect, the sysfs files of the subdevices are also deleted. So, by the time pvr_i2c_core_done is called by pvr_context_destroy, the sysfs files have been deleted.
To fix this, unregister the i2c adapter too in pvr_hdw_disconnect. Make the device deregistration code shared by calling pvr_hdw_disconnect from pvr2_hdw_destroy.
--- drivers/media/usb/pvrusb2/pvrusb2-hdw.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/media/usb/pvrusb2/pvrusb2-hdw.c +2 -2
@@ -2677,9 +2677,8 @@ void pvr2_hdw_destroy(struct pvr2_hdw *hdw)pvr2_stream_destroy (hdw->vid_stream); hdw->vid_stream =NULL ; } -pvr2_i2c_core_done (hdw);v4l2_device_unregister (&hdw->v4l2_dev); -pvr2_hdw_remove_usb_stuff (hdw); +pvr2_hdw_disconnect (hdw);mutex_lock (&pvr2_unit_mtx); do { if ((hdw->unit_number >= 0) &&
@@ -2706,6 +2705,7 @@ void pvr2_hdw_disconnect(struct pvr2_hdw *hdw) {pvr2_trace (PVR2_TRACE_INIT ,"pvr2_hdw_disconnect(hdw=%p)" ,hdw);LOCK_TAKE (hdw->big_lock); +pvr2_i2c_core_done (hdw);LOCK_TAKE (hdw->ctl_lock);pvr2_hdw_remove_usb_stuff (hdw);LOCK_GIVE (hdw->ctl_lock);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 19/50 media: imx: imx7_mipi_csis: Fix logging of only error event counters
In reply to Sasha LevinFrom: Laurent Pinchart <[email protected]>
[ Upstream commit d2fcc9c2de1191ea80366e3658711753738dd10a ]
The mipi_csis_events array ends with 6 non-error events, not 4. Update mipi_csis_log_counters() accordingly. While at it, log event counters in forward order, as there's no reason to log them backward.
--- drivers/staging/media/imx/imx7-mipi-csis.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/staging/media/imx/imx7-mipi-csis.c +4 -2
@@ -528,13 +528,15 @@ static void mipi_csis_clear_counters(struct csi_state *state)static void mipi_csis_log_counters (struct csi_state *state,bool non_errors) { -int i = non_errors ?MIPI_CSIS_NUM_EVENTS :MIPI_CSIS_NUM_EVENTS -4 ; +unsigned int num_events = non_errors ?MIPI_CSIS_NUM_EVENTS + :MIPI_CSIS_NUM_EVENTS -6 ;struct device *dev = &state->pdev->dev;unsigned long flags; +unsigned int i;spin_lock_irqsave (&state->slock, flags); -for (i--; i >=0 ; i--) { +for (i =0 ; i < num_events; ++i) {if (state->events[i].counter >0 || state->debug)dev_info (dev,"%s events: %d\n" , state->events[i].name, state->events[i].counter);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 20/50 crypto: qat - check return code of qat_hal_rd_rel_reg()
In reply to Sasha LevinFrom: Jack Xu <[email protected]>
[ Upstream commit 96b57229209490c8bca4335b01a426a96173dc56 ]
Check the return code of the function qat_hal_rd_rel_reg() and return it to the caller.
This is to fix the following warning when compiling the driver with clang scan-build:
drivers/crypto/qat/qat_common/qat_hal.c:1436:2: warning: 6th function call argument is an uninitialized value
--- drivers/crypto/qat/qat_common/qat_hal.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/crypto/qat/qat_common/qat_hal.c +5 -1
@@ -1256,7 +1256,11 @@ static int qat_hal_put_rel_wr_xfer(struct icp_qat_fw_loader_handle *handle,pr_err ("QAT: bad xfrAddr=0x%x\n" , xfr_addr);return -EINVAL ; } -qat_hal_rd_rel_reg (handle, ae, ctx,ICP_GPB_REL , gprnum, &gprval); + status =qat_hal_rd_rel_reg (handle, ae, ctx,ICP_GPB_REL , gprnum, &gprval); +if (status) { +pr_err ("QAT: failed to read register" ); +return status; + } gpr_addr =qat_hal_get_reg_addr (ICP_GPB_REL , gprnum); data16low =0xffff & data; data16hi =0xffff & (data >>0x10 );
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 21/50 crypto: qat - remove unused macro in FW loader
In reply to Sasha LevinFrom: Jack Xu <[email protected]>
[ Upstream commit 9afe77cf25d9670e61b489fd52cc6f75fd7f6803 ]
Remove the unused macro ICP_DH895XCC_PESRAM_BAR_SIZE in the firmware loader.
This is to fix the following warning when compiling the driver using the clang compiler with CC=clang W=2:
drivers/crypto/qat/qat_common/qat_uclo.c:345:9: warning: macro is not used [-Wunused-macros]
--- drivers/crypto/qat/qat_common/qat_uclo.c | 1 - 1 file changed, 1 deletion(-)
drivers/crypto/qat/qat_common/qat_uclo.c +0 -1
@@ -385,7 +385,6 @@ static int qat_uclo_init_umem_seg(struct icp_qat_fw_loader_handle *handle,return 0 ; } -#define ICP_DH895XCC_PESRAM_BAR_SIZE 0x80000static int qat_uclo_init_ae_memory (struct icp_qat_fw_loader_handle *handle,struct icp_qat_uof_initmem *init_mem) {
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 22/50 sched/fair: Fix ascii art by relpacing tabs
In reply to Sasha LevinFrom: Odin Ugedal <[email protected]>
[ Upstream commit 08f7c2f4d0e9f4283f5796b8168044c034a1bfcb ]
When using something other than 8 spaces per tab, this ascii art makes not sense, and the reader might end up wondering what this advanced equation "is".
--- kernel/sched/fair.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
kernel/sched/fair.c +4 -4
@@ -2927,7 +2927,7 @@ void reweight_task(struct task_struct *p, int prio)* * tg->weight * grq->load.weight * ge->load.weight = ----------------------------- (1) -* \Sum grq->load.weight +* \Sum grq->load.weight * * Now, because computing that sum is prohibitively expensive to compute (been * there, done that) we approximate it with this average stuff. The average
@@ -2941,7 +2941,7 @@ void reweight_task(struct task_struct *p, int prio)* * tg->weight * grq->avg.load_avg * ge->load.weight = ------------------------------ (3) -* tg->load_avg +* tg->load_avg * * Where: tg->load_avg ~= \Sum grq->avg.load_avg *
@@ -2957,7 +2957,7 @@ void reweight_task(struct task_struct *p, int prio)* * tg->weight * grq->load.weight * ge->load.weight = ----------------------------- = tg->weight (4) -* grp->load.weight +* grp->load.weight * * That is, the sum collapses because all other CPUs are idle; the UP scenario. *
@@ -2976,7 +2976,7 @@ void reweight_task(struct task_struct *p, int prio)* * tg->weight * grq->load.weight * ge->load.weight = ----------------------------- (6) -* tg_load_avg' +* tg_load_avg' * * Where: *
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 23/50 media: em28xx: Fix possible memory leak of em28xx struct
In reply to Sasha LevinFrom: Igor Matheus Andrade Torrente <[email protected]>
[ Upstream commit ac5688637144644f06ed1f3c6d4dd8bb7db96020 ]
The em28xx struct kref isn't being decreased after an error in the em28xx_ir_init, leading to a possible memory leak.
A kref_put and em28xx_shutdown_buttons is added to the error handler code.
--- drivers/media/usb/em28xx/em28xx-input.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/media/usb/em28xx/em28xx-input.c +6 -2
@@ -720,7 +720,8 @@ static int em28xx_ir_init(struct em28xx *dev) dev->board.has_ir_i2c =0 ;dev_warn (&dev->intf->dev,"No i2c IR remote control device found.\n" ); -return -ENODEV ; + err = -ENODEV ; + goto ref_put; } }
@@ -735,7 +736,7 @@ static int em28xx_ir_init(struct em28xx *dev) ir =kzalloc (sizeof (*ir),GFP_KERNEL );if (!ir) -return -ENOMEM ; + goto ref_put; rc =rc_allocate_device (RC_DRIVER_SCANCODE );if (!rc) goto error;
@@ -839,6 +840,9 @@ static int em28xx_ir_init(struct em28xx *dev) dev->ir =NULL ;rc_free_device (rc);kfree (ir); +ref_put: +em28xx_shutdown_buttons (dev); +kref_put (&dev->ref, em28xx_free_device);return err; }
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 24/50 media: v4l2-core: Avoid the dangling pointer in v4l2_fh_release
In reply to Sasha LevinFrom: Lv Yunlong <[email protected]>
[ Upstream commit 7dd0c9e547b6924e18712b6b51aa3cba1896ee2c ]
A use after free bug caused by the dangling pointer filp->privitate_data in v4l2_fh_release.
See https://lore.kernel.org/patchwork/patch/1419058/.
My patch sets the dangling pointer to NULL to provide robust.
--- drivers/media/v4l2-core/v4l2-fh.c | 1 + 1 file changed, 1 insertion(+)
drivers/media/v4l2-core/v4l2-fh.c +1 -0
@@ -96,6 +96,7 @@ int v4l2_fh_release(struct file *filp)v4l2_fh_del (fh);v4l2_fh_exit (fh);kfree (fh); + filp->private_data =NULL ; }return 0 ; }
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 25/50 media: bt8xx: Fix a missing check bug in bt878_probe
In reply to Sasha LevinFrom: Zheyu Ma <[email protected]>
[ Upstream commit 1a4520090681853e6b850cbe54b27247a013e0e5 ]
In 'bt878_irq', the driver calls 'tasklet_schedule', but this tasklet is set in 'dvb_bt8xx_load_card' of another driver 'dvb-bt8xx'. However, this two drivers are separate. The user may not load the 'dvb-bt8xx' driver when loading the 'bt8xx' driver, that is, the tasklet has not been initialized when 'tasklet_schedule' is called, so it is necessary to check whether the tasklet is initialized in 'bt878_probe'.
Fix this by adding a check at the end of bt878_probe.
The KASAN's report reveals it:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 PGD 800000006aab2067 P4D 800000006aab2067 PUD 6b2ea067 PMD 0 Oops: 0010 [#1] PREEMPT SMP KASAN PTI CPU: 2 PID: 8724 Comm: syz-executor.0 Not tainted 4.19.177- gdba4159c14ef-dirty #40 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59- gc9ba5276e321-prebuilt.qemu.org 04/01/2014 RIP: 0010: (null) Code: Bad RIP value. RSP: 0018:ffff88806c287ea0 EFLAGS: 00010246 RAX: fffffbfff1b01774 RBX: dffffc0000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 1ffffffff1b01775 RDI: 0000000000000000 RBP: ffff88806c287f00 R08: fffffbfff1b01774 R09: fffffbfff1b01774 R10: 0000000000000001 R11: fffffbfff1b01773 R12: 0000000000000000 R13: ffff88806c29f530 R14: ffffffff8d80bb88 R15: ffffffff8d80bb90 FS: 00007f6b550e6700(0000) GS:ffff88806c280000(0000) knlGS: 0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 000000005ec98000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <IRQ> tasklet_action_common.isra.17+0x141/0x420 kernel/softirq.c:522 tasklet_action+0x50/0x70 kernel/softirq.c:540 __do_softirq+0x224/0x92c kernel/softirq.c:292 invoke_softirq kernel/softirq.c:372 [inline] irq_exit+0x15a/0x180 kernel/softirq.c:412 exiting_irq arch/x86/include/asm/apic.h:535 [inline] do_IRQ+0x123/0x1e0 arch/x86/kernel/irq.c:260 common_interrupt+0xf/0xf arch/x86/entry/entry_64.S:670 </IRQ> RIP: 0010:__do_sys_interrupt kernel/sys.c:2593 [inline] RIP: 0010:__se_sys_interrupt kernel/sys.c:2584 [inline] RIP: 0010:__x64_sys_interrupt+0x5b/0x80 kernel/sys.c:2584 Code: ba 00 04 00 00 48 c7 c7 c0 99 31 8c e8 ae 76 5e 01 48 85 c0 75 21 e8
14 ae 24 00 48 c7 c3 c0 99 31 8c b8 0c 00 00 00 0f 01 c1 <31> db e8 fe ad 24 00 48 89 d8 5b 5d c3 48 c7 c3 ea ff ff ff eb ec
RSP: 0018:ffff888054167f10 EFLAGS: 00000212 ORIG_RAX: ffffffffffffffde
RAX: 000000000000000c RBX: ffffffff8c3199c0 RCX: ffffc90001ca6000
RDX: 000000000000001a RSI: ffffffff813478fc RDI: ffffffff8c319dc0
RBP: ffff888054167f18 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000080 R11: fffffbfff18633b7 R12: ffff888054167f58
R13: ffff88805f638000 R14: 0000000000000000 R15: 0000000000000000
do_syscall_64+0xb0/0x4e0 arch/x86/entry/common.c:293 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4692a9 Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7
48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6b550e5c48 EFLAGS: 00000246 ORIG_RAX: 000000000000014f
RAX: ffffffffffffffda RBX: 000000000077bf60 RCX: 00000000004692a9
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020000140
RBP: 00000000004cf7eb R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000077bf60
R13: 0000000000000000 R14: 000000000077bf60 R15: 00007fff55a1dca0
Modules linked in: Dumping ftrace buffer: (ftrace buffer empty) CR2: 0000000000000000 ---[ end trace 68e5849c3f77cbb6 ]--- RIP: 0010: (null) Code: Bad RIP value. RSP: 0018:ffff88806c287ea0 EFLAGS: 00010246 RAX: fffffbfff1b01774 RBX: dffffc0000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 1ffffffff1b01775 RDI: 0000000000000000 RBP: ffff88806c287f00 R08: fffffbfff1b01774 R09: fffffbfff1b01774 R10: 0000000000000001 R11: fffffbfff1b01773 R12: 0000000000000000 R13: ffff88806c29f530 R14: ffffffff8d80bb88 R15: ffffffff8d80bb90 FS: 00007f6b550e6700(0000) GS:ffff88806c280000(0000) knlGS: 0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 000000005ec98000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
--- drivers/media/pci/bt8xx/bt878.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/media/pci/bt8xx/bt878.c +3 -0
@@ -477,6 +477,9 @@ static int bt878_probe(struct pci_dev *dev, const struct pci_device_id *pci_id)btwrite (0 ,BT878_AINT_MASK ); bt878_num++; +if (!bt->tasklet.func) +tasklet_disable (&bt->tasklet); +return 0 ; fail2:
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 26/50 media: st-hva: Fix potential NULL pointer dereferences
In reply to Sasha LevinFrom: Evgeny Novikov <[email protected]>
[ Upstream commit b7fdd208687ba59ebfb09b2199596471c63b69e3 ]
When ctx_id >= HVA_MAX_INSTANCES in hva_hw_its_irq_thread() it tries to access fields of ctx that is NULL at that point. The patch gets rid of these accesses.
Found by Linux Driver Verification project (linuxtesting.org).
--- drivers/media/platform/sti/hva/hva-hw.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/media/platform/sti/hva/hva-hw.c +1 -2
@@ -130,8 +130,7 @@ static irqreturn_t hva_hw_its_irq_thread(int irq, void *arg) ctx_id = (hva->sts_reg &0xFF00 ) >>8 ;if (ctx_id >=HVA_MAX_INSTANCES ) {dev_err (dev,"%s %s: bad context identifier: %d\n" , - ctx->name, __func__, ctx_id); - ctx->hw_err = true; +HVA_PREFIX , __func__, ctx_id); goto out; }
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 27/50 Makefile: fix GDB warning with CONFIG_RELR
In reply to Sasha LevinFrom: Nick Desaulniers <[email protected]>
[ Upstream commit 27f2a4db76e8d8a8b601fc1c6a7a17f88bd907ab ]
GDB produces the following warning when debugging kernels built with CONFIG_RELR:
BFD: /android0/linux-next/vmlinux: unknown type [0x13] section `.relr.dyn'
when loading a kernel built with CONFIG_RELR into GDB. It can also prevent debugging symbols using such relocations.
Peter sugguests:
[That flag] means that lld will use dynamic tags and section type numbers in the OS-specific range rather than the generic range. The kernel itself doesn't care about these numbers; it determines the location of the RELR section using symbols defined by a linker script.
--- Makefile | 2 +- scripts/tools-support-relr.sh | 3 ++- 2 files changed, 3 insertions(+), 2 deletions(-)
Makefile +1 -1
@@ -937,7 +937,7 @@ LDFLAGS_vmlinux += $(call ld-option, -X,) endif ifeq ($(CONFIG_RELR),y) -LDFLAGS_vmlinux += --pack-dyn-relocs=relr +LDFLAGS_vmlinux += --pack-dyn-relocs=relr --use-android-relr-tags endif # make the checker run with the right architecture
scripts/tools-support-relr.sh +2 -1
@@ -7,7 +7,8 @@ trap "rm -f $tmp_file.o $tmp_file $tmp_file.bin" EXIT cat << "END" | $CC -c -x c - -o $tmp_file.o >/dev/null 2>&1 void *p = &p; END -$LD $tmp_file.o -shared -Bsymbolic --pack-dyn-relocs=relr -o $tmp_file +$LD $tmp_file.o -shared -Bsymbolic --pack-dyn-relocs=relr \ + --use-android-relr-tags -o $tmp_file # Despite printing an error message, GNU nm still exits with exit code 0 if it # sees a relr section. So we need to check that nothing is printed to stderr.
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 28/50 media: dvd_usb: memory leak in cinergyt2_fe_attach
In reply to Sasha LevinFrom: Dongliang Mu <[email protected]>
[ Upstream commit 9ad1efee086e0e913914fa2b2173efb830bad68c ]
When the driver fails to talk with the hardware with dvb_usb_generic_rw, it will return an error to dvb_usb_adapter_frontend_init. However, the driver forgets to free the resource (e.g., struct cinergyt2_fe_state), which leads to a memory leak.
Fix this by freeing struct cinergyt2_fe_state when dvb_usb_generic_rw fails in cinergyt2_frontend_attach.
backtrace:
[<0000000056e17b1a>] kmalloc include/linux/slab.h:552 [inline] [<0000000056e17b1a>] kzalloc include/linux/slab.h:682 [inline] [<0000000056e17b1a>] cinergyt2_fe_attach+0x21/0x80 drivers/media/usb/dvb-usb/cinergyT2-fe.c:271 [<00000000ae0b1711>] cinergyt2_frontend_attach+0x21/0x70 drivers/media/usb/dvb-usb/cinergyT2-core.c:74 [<00000000d0254861>] dvb_usb_adapter_frontend_init+0x11b/0x1b0 drivers/media/usb/dvb-usb/dvb-usb-dvb.c:290 [<0000000002e08ac6>] dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:84 [inline] [<0000000002e08ac6>] dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:173 [inline] [<0000000002e08ac6>] dvb_usb_device_init.cold+0x4d0/0x6ae drivers/media/usb/dvb-usb/dvb-usb-init.c:287
--- drivers/media/usb/dvb-usb/cinergyT2-core.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/media/usb/dvb-usb/cinergyT2-core.c +2 -0
@@ -78,6 +78,8 @@ static int cinergyt2_frontend_attach(struct dvb_usb_adapter *adap) ret =dvb_usb_generic_rw (d, st->data,1 , st->data,3 ,0 );if (ret <0 ) { +if (adap->fe_adap[0 ].fe) + adap->fe_adap[0 ].fe->ops.release (adap->fe_adap[0 ].fe);deb_rc ("cinergyt2_power_ctrl() Failed to retrieve sleep state info\n" ); }mutex_unlock (&d->data_mutex);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 29/50 memstick: rtsx_usb_ms: fix UAF
In reply to Sasha LevinFrom: Tong Zhang <[email protected]>
[ Upstream commit 42933c8aa14be1caa9eda41f65cde8a3a95d3e39 ]
This patch fixes the following issues:
1. memstick_free_host() will free the host, so the use of ms_dev(host) after it will be a problem. To fix this, move memstick_free_host() after when we are done with ms_dev(host).
2. In rtsx_usb_ms_drv_remove(), pm need to be disabled before we remove and free host otherwise memstick_check will be called and UAF will happen.
[ 11.351173] BUG: KASAN: use-after-free in rtsx_usb_ms_drv_remove+0x94/0x140 [rtsx_usb_ms] [ 11.357077] rtsx_usb_ms_drv_remove+0x94/0x140 [rtsx_usb_ms] [ 11.357376] platform_remove+0x2a/0x50 [ 11.367531] Freed by task 298: [ 11.368537] kfree+0xa4/0x2a0 [ 11.368711] device_release+0x51/0xe0 [ 11.368905] kobject_put+0xa2/0x120 [ 11.369090] rtsx_usb_ms_drv_remove+0x8c/0x140 [rtsx_usb_ms] [ 11.369386] platform_remove+0x2a/0x50
[ 12.038408] BUG: KASAN: use-after-free in __mutex_lock.isra.0+0x3ec/0x7c0 [ 12.045432] mutex_lock+0xc9/0xd0 [ 12.046080] memstick_check+0x6a/0x578 [memstick] [ 12.046509] process_one_work+0x46d/0x750 [ 12.052107] Freed by task 297: [ 12.053115] kfree+0xa4/0x2a0 [ 12.053272] device_release+0x51/0xe0 [ 12.053463] kobject_put+0xa2/0x120 [ 12.053647] rtsx_usb_ms_drv_remove+0xc4/0x140 [rtsx_usb_ms] [ 12.053939] platform_remove+0x2a/0x50
--- drivers/memstick/host/rtsx_usb_ms.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-)
drivers/memstick/host/rtsx_usb_ms.c +4 -6
@@ -799,9 +799,9 @@ static int rtsx_usb_ms_drv_probe(struct platform_device *pdev)return 0 ; err_out: -memstick_free_host (msh);pm_runtime_disable (ms_dev (host));pm_runtime_put_noidle (ms_dev (host)); +memstick_free_host (msh);return err; }
@@ -828,9 +828,6 @@ static int rtsx_usb_ms_drv_remove(struct platform_device *pdev) }mutex_unlock (&host->host_mutex); -memstick_remove_host (msh); -memstick_free_host (msh); -/* Balance possible unbalanced usage count * e.g. unconditional module removal */
@@ -838,10 +835,11 @@ static int rtsx_usb_ms_drv_remove(struct platform_device *pdev)pm_runtime_put (ms_dev (host));pm_runtime_disable (ms_dev (host)); -platform_set_drvdata (pdev,NULL ); - +memstick_remove_host (msh);dev_dbg (ms_dev (host),": Realtek USB Memstick controller has been removed\n" ); +memstick_free_host (msh); +platform_set_drvdata (pdev,NULL );return 0 ; }
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 30/50 mmc: sdhci-sprd: use sdhci_sprd_writew
In reply to Sasha LevinFrom: Krzysztof Kozlowski <[email protected]>
[ Upstream commit 961470820021e6f9d74db4837bd6831a1a30341b ]
The sdhci_sprd_writew() was defined by never used in sdhci_ops:
drivers/mmc/host/sdhci-sprd.c:134:20: warning: unused function 'sdhci_sprd_writew'
--- drivers/mmc/host/sdhci-sprd.c | 1 + 1 file changed, 1 insertion(+)
drivers/mmc/host/sdhci-sprd.c +1 -0
@@ -382,6 +382,7 @@ static unsigned int sdhci_sprd_get_ro(struct sdhci_host *host)static struct sdhci_ops sdhci_sprd_ops = { .read_l = sdhci_sprd_readl, .write_l = sdhci_sprd_writel, + .write_w = sdhci_sprd_writew, .write_b = sdhci_sprd_writeb, .set_clock = sdhci_sprd_set_clock, .get_max_clock = sdhci_sprd_get_max_clock,
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 31/50 mmc: via-sdmmc: add a check against NULL pointer dereference
In reply to Sasha LevinFrom: Zheyu Ma <[email protected]>
[ Upstream commit 45c8ddd06c4b729c56a6083ab311bfbd9643f4a6 ]
Before referencing 'host->data', the driver needs to check whether it is null pointer, otherwise it will cause a null pointer reference.
This log reveals it:
[ 29.355199] BUG: kernel NULL pointer dereference, address: 0000000000000014 [ 29.357323] #PF: supervisor write access in kernel mode [ 29.357706] #PF: error_code(0x0002) - not-present page [ 29.358088] PGD 0 P4D 0 [ 29.358280] Oops: 0002 [#1] PREEMPT SMP PTI [ 29.358595] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4- g70e7f0549188-dirty #102 [ 29.359164] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 29.359978] RIP: 0010:via_sdc_isr+0x21f/0x410 [ 29.360314] Code: ff ff e8 84 aa d0 fd 66 45 89 7e 28 66 41 f7 c4 00 10 75 56 e8 72 aa d0 fd 66 41 f7 c4 00 c0 74 10 e8 65 aa d0 fd 48 8b 43 18 <c7> 40 14 ac ff ff ff e8 55 aa d0 fd 48 89 df e8 ad fb ff ff e9 77 [ 29.361661] RSP: 0018:ffffc90000118e98 EFLAGS: 00010046 [ 29.362042] RAX: 0000000000000000 RBX: ffff888107d77880 RCX: 0000000000000000 [ 29.362564] RDX: 0000000000000000 RSI: ffffffff835d20bb RDI: 00000000ffffffff [ 29.363085] RBP: ffffc90000118ed8 R08: 0000000000000001 R09: 0000000000000001 [ 29.363604] R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000008600 [ 29.364128] R13: ffff888107d779c8 R14: ffffc90009c00200 R15: 0000000000008000 [ 29.364651] FS: 0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000 [ 29.365235] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 29.365655] CR2: 0000000000000014 CR3: 0000000005a2e000 CR4: 00000000000006e0 [ 29.366170] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 29.366683] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 29.367197] Call Trace: [ 29.367381] <IRQ> [ 29.367537] __handle_irq_event_percpu+0x53/0x3e0 [ 29.367916] handle_irq_event_percpu+0x35/0x90 [ 29.368247] handle_irq_event+0x39/0x60 [ 29.368632] handle_fasteoi_irq+0xc2/0x1d0 [ 29.368950] __common_interrupt+0x7f/0x150 [ 29.369254] common_interrupt+0xb4/0xd0 [ 29.369547] </IRQ> [ 29.369708] asm_common_interrupt+0x1e/0x40 [ 29.370016] RIP: 0010:native_safe_halt+0x17/0x20 [ 29.370360] Code: 07 0f 00 2d db 80 43 00 f4 5d c3 0f 1f 84 00 00 00 00 00 8b 05 c2 37 e5 01 55 48 89 e5 85 c0 7e 07 0f 00 2d bb 80 43 00 fb f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d f9 91 [ 29.371696] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246 [ 29.372079] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000 [ 29.372595] RDX: 0000000000000000 RSI: ffffffff854f67a4 RDI: ffffffff85403406 [ 29.373122] RBP: ffffc9000008fe90 R08: 0000000000000001 R09: 0000000000000001 [ 29.373646] R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86009188 [ 29.374160] R13: 0000000000000000 R14: 0000000000000000 R15: ffff888100258000 [ 29.374690] default_idle+0x9/0x10 [ 29.374944] arch_cpu_idle+0xa/0x10 [ 29.375198] default_idle_call+0x6e/0x250 [ 29.375491] do_idle+0x1f0/0x2d0 [ 29.375740] cpu_startup_entry+0x18/0x20 [ 29.376034] start_secondary+0x11f/0x160 [ 29.376328] secondary_startup_64_no_verify+0xb0/0xbb [ 29.376705] Modules linked in: [ 29.376939] Dumping ftrace buffer: [ 29.377187] (ftrace buffer empty) [ 29.377460] CR2: 0000000000000014 [ 29.377712] ---[ end trace 51a473dffb618c47 ]--- [ 29.378056] RIP: 0010:via_sdc_isr+0x21f/0x410 [ 29.378380] Code: ff ff e8 84 aa d0 fd 66 45 89 7e 28 66 41 f7 c4 00 10 75 56 e8 72 aa d0 fd 66 41 f7 c4 00 c0 74 10 e8 65 aa d0 fd 48 8b 43 18 <c7> 40 14 ac ff ff ff e8 55 aa d0 fd 48 89 df e8 ad fb ff ff e9 77 [ 29.379714] RSP: 0018:ffffc90000118e98 EFLAGS: 00010046 [ 29.380098] RAX: 0000000000000000 RBX: ffff888107d77880 RCX: 0000000000000000 [ 29.380614] RDX: 0000000000000000 RSI: ffffffff835d20bb RDI: 00000000ffffffff [ 29.381134] RBP: ffffc90000118ed8 R08: 0000000000000001 R09: 0000000000000001 [ 29.381653] R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000008600 [ 29.382176] R13: ffff888107d779c8 R14: ffffc90009c00200 R15: 0000000000008000 [ 29.382697] FS: 0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000 [ 29.383277] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 29.383697] CR2: 0000000000000014 CR3: 0000000005a2e000 CR4: 00000000000006e0 [ 29.384223] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 29.384736] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 29.385260] Kernel panic - not syncing: Fatal exception in interrupt [ 29.385882] Dumping ftrace buffer: [ 29.386135] (ftrace buffer empty) [ 29.386401] Kernel Offset: disabled [ 29.386656] Rebooting in 1 seconds..
--- drivers/mmc/host/via-sdmmc.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/mmc/host/via-sdmmc.c +3 -0
@@ -857,6 +857,9 @@ static void via_sdc_data_isr(struct via_crdr_mmc_host *host, u16 intmask) {BUG_ON (intmask ==0 ); +if (!host->data) +return ; +if (intmask &VIA_CRDR_SDSTS_DT ) host->data->error = -ETIMEDOUT ;else if (intmask & (VIA_CRDR_SDSTS_RC |VIA_CRDR_SDSTS_WC ))
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 32/50 crypto: shash - avoid comparing pointers to exported functions under CFI
In reply to Sasha LevinFrom: Ard Biesheuvel <[email protected]>
[ Upstream commit 22ca9f4aaf431a9413dcc115dd590123307f274f ]
crypto_shash_alg_has_setkey() is implemented by testing whether the .setkey() member of a struct shash_alg points to the default version, called shash_no_setkey(). As crypto_shash_alg_has_setkey() is a static inline, this requires shash_no_setkey() to be exported to modules.
Unfortunately, when building with CFI, function pointers are routed via CFI stubs which are private to each module (or to the kernel proper) and so this function pointer comparison may fail spuriously.
Let's fix this by turning crypto_shash_alg_has_setkey() into an out of line function.
--- crypto/shash.c | 18 +++++++++++++++--- include/crypto/internal/hash.h | 8 +------- 2 files changed, 16 insertions(+), 10 deletions(-)
crypto/shash.c +15 -3
@@ -20,12 +20,24 @@static const struct crypto_type crypto_shash_type; -int shash_no_setkey (struct crypto_shash *tfm,const u8 *key, -unsigned int keylen) +static int shash_no_setkey (struct crypto_shash *tfm,const u8 *key, +unsigned int keylen) {return -ENOSYS ; } -EXPORT_SYMBOL_GPL (shash_no_setkey); + +/* +* Check whether an shash algorithm has a setkey function. +* +* For CFI compatibility, this must not be an inline function. This is because +* when CFI is enabled, modules won't get the same address for shash_no_setkey +* (if it were exported, which inlining would require) as the core kernel will. +*/ +bool crypto_shash_alg_has_setkey (struct shash_alg *alg) +{ +return alg->setkey != shash_no_setkey; +} +EXPORT_SYMBOL_GPL (crypto_shash_alg_has_setkey);static int shash_setkey_unaligned (struct crypto_shash *tfm,const u8 *key,unsigned int keylen)
include/crypto/internal/hash.h +1 -7
@@ -77,13 +77,7 @@ int ahash_register_instance(struct crypto_template *tmpl, struct ahash_instance *inst);void ahash_free_instance (struct crypto_instance *inst); -int shash_no_setkey (struct crypto_shash *tfm,const u8 *key, -unsigned int keylen); - -static inline bool crypto_shash_alg_has_setkey (struct shash_alg *alg) -{ -return alg->setkey != shash_no_setkey; -} +bool crypto_shash_alg_has_setkey (struct shash_alg *alg);bool crypto_hash_alg_has_setkey (struct hash_alg_common *halg);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 33/50 media: dvb_net: avoid speculation from net slot
In reply to Sasha LevinFrom: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit abc0226df64dc137b48b911c1fe4319aec5891bb ]
The risk of especulation is actually almost-non-existing here, as there are very few users of TCP/IP using the DVB stack, as, this is mainly used with DVB-S/S2 cards, and only by people that receives TCP/IP from satellite connections, which limits a lot the number of users of such feature(*).
(*) In thesis, DVB-C cards could also benefit from it, but I'm yet to see a hardware that supports it.
Yet, fixing it is trivial.
--- drivers/media/dvb-core/dvb_net.c | 25 +++++++++++++++++++------ 1 file changed, 19 insertions(+), 6 deletions(-)
drivers/media/dvb-core/dvb_net.c +19 -6
@@ -45,6 +45,7 @@#include <linux/module.h> #include <linux/kernel.h> #include <linux/netdevice.h> +#include <linux/nospec.h> #include <linux/etherdevice.h> #include <linux/dvb/net.h> #include <linux/uio.h>
@@ -1462,14 +1463,20 @@ static int dvb_net_do_ioctl(struct file *file,struct net_device *netdev;struct dvb_net_priv *priv_data;struct dvb_net_if *dvbnetif = parg; +int if_num = dvbnetif->if_num; -if (dvbnetif->if_num >=DVB_NET_DEVICES_MAX || - !dvbnet->state[dvbnetif->if_num]) { +if (if_num >=DVB_NET_DEVICES_MAX ) { ret = -EINVAL ; goto ioctl_error; } + if_num =array_index_nospec (if_num,DVB_NET_DEVICES_MAX ); - netdev = dvbnet->device[dvbnetif->if_num]; +if (!dvbnet->state[if_num]) { + ret = -EINVAL ; + goto ioctl_error; + } + + netdev = dvbnet->device[if_num]; priv_data =netdev_priv (netdev); dvbnetif->pid=priv_data->pid;
@@ -1522,14 +1529,20 @@ static int dvb_net_do_ioctl(struct file *file,struct net_device *netdev;struct dvb_net_priv *priv_data;struct __dvb_net_if_old *dvbnetif = parg; +int if_num = dvbnetif->if_num; + +if (if_num >=DVB_NET_DEVICES_MAX ) { + ret = -EINVAL ; + goto ioctl_error; + } + if_num =array_index_nospec (if_num,DVB_NET_DEVICES_MAX ); -if (dvbnetif->if_num >=DVB_NET_DEVICES_MAX || - !dvbnet->state[dvbnetif->if_num]) { +if (!dvbnet->state[if_num]) { ret = -EINVAL ; goto ioctl_error; } - netdev = dvbnet->device[dvbnetif->if_num]; + netdev = dvbnet->device[if_num]; priv_data =netdev_priv (netdev); dvbnetif->pid=priv_data->pid;
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 34/50 media: siano: fix device register error path
In reply to Sasha LevinFrom: Mauro Carvalho Chehab <[email protected]>
[ Upstream commit 5368b1ee2939961a16e74972b69088433fc52195 ]
As reported by smatch:
drivers/media/common/siano/smsdvb-main.c:1231 smsdvb_hotplug() warn: '&client->entry' not removed from list
If an error occur at the end of the registration logic, it won't drop the device from the list.
--- drivers/media/common/siano/smsdvb-main.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/media/common/siano/smsdvb-main.c +4 -0
@@ -1176,6 +1176,10 @@ static int smsdvb_hotplug(struct smscore_device_t *coredev,return 0 ; media_graph_error: +mutex_lock (&g_smsdvb_clientslock); +list_del (&client->entry); +mutex_unlock (&g_smsdvb_clientslock); +smsdvb_debugfs_release (client); client_error:
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 35/50 media: imx-csi: Skip first few frames from a BT.656 source
In reply to Sasha LevinFrom: Steve Longerbeam <[email protected]>
[ Upstream commit e198be37e52551bb863d07d2edc535d0932a3c4f ]
Some BT.656 sensors (e.g. ADV718x) transmit frames with unstable BT.656 sync codes after initial power on. This confuses the imx CSI,resulting in vertical and/or horizontal sync issues. Skip the first 20 frames to avoid the unstable sync codes.
[fabio: fixed checkpatch warning and increased the frame skipping to 20]
--- drivers/staging/media/imx/imx-media-csi.c | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-)
drivers/staging/media/imx/imx-media-csi.c +13 -1
@@ -753,9 +753,10 @@ static int csi_setup(struct csi_priv *priv)static int csi_start (struct csi_priv *priv) { -struct v4l2_fract *output_fi; +struct v4l2_fract *input_fi, *output_fi;int ret; + input_fi = &priv->frame_interval[CSI_SINK_PAD ]; output_fi = &priv->frame_interval[priv->active_output_pad];/* start upstream */
@@ -764,6 +765,17 @@ static int csi_start(struct csi_priv *priv)if (ret)return ret; +/* Skip first few frames from a BT.656 source */ +if (priv->upstream_ep.bus_type ==V4L2_MBUS_BT656 ) { +u32 delay_usec, bad_frames =20 ; + + delay_usec =DIV_ROUND_UP_ULL ((u64 )USEC_PER_SEC * + input_fi->numerator * bad_frames, + input_fi->denominator); + +usleep_range (delay_usec, delay_usec +1000 ); + } +if (priv->dest ==IPU_CSI_DEST_IDMAC ) { ret =csi_idmac_start (priv);if (ret)
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 36/50 hwmon: (max31790) Report correct current pwm duty cycles
In reply to Sasha LevinFrom: Guenter Roeck <[email protected]>
[ Upstream commit 897f6339893b741a5d68ae8e2475df65946041c2 ]
The MAX31790 has two sets of registers for pwm duty cycles, one to request a duty cycle and one to read the actual current duty cycle. Both do not have to be the same.
When reporting the pwm duty cycle to the user, the actual pwm duty cycle from pwm duty cycle registers needs to be reported. When setting it, the pwm target duty cycle needs to be written. Since we don't know the actual pwm duty cycle after a target pwm duty cycle has been written, set the valid flag to false to indicate that actual pwm duty cycle should be read from the chip instead of using cached values.
--- Documentation/hwmon/max31790.rst | 3 ++- drivers/hwmon/max31790.c | 6 +++--- 2 files changed, 5 insertions(+), 4 deletions(-)
Documentation/hwmon/max31790.rst +2 -1
@@ -39,5 +39,6 @@ fan[1-12]_input RO fan tachometer speed in RPM fan[1-12]_fault RO fan experienced fault fan[1-6]_target RW desired fan speed in RPM pwm[1-6]_enable RW regulator mode, 0=disabled, 1=manual mode, 2=rpm mode -pwm[1-6] RW fan target duty cycle (0-255) +pwm[1-6] RW read: current pwm duty cycle, + write: target pwm duty cycle (0-255) ================== === =======================================================
drivers/hwmon/max31790.c +3 -3
@@ -104,7 +104,7 @@ static struct max31790_data *max31790_update_device(struct device *dev) data->tach[NR_CHANNEL + i] = rv; }else { rv =i2c_smbus_read_word_swapped (client, -MAX31790_REG_PWMOUT (i)); +MAX31790_REG_PWM_DUTY_CYCLE (i));if (rv <0 ) goto abort; data->pwm[i] = rv;
@@ -299,10 +299,10 @@ static int max31790_write_pwm(struct device *dev, u32 attr, int channel, err = -EINVAL ;break ; } - data->pwm[channel] = val <<8 ; + data->valid = false; err =i2c_smbus_write_word_swapped (client,MAX31790_REG_PWMOUT (channel), - data->pwm[channel]); + val <<8 );break ;case hwmon_pwm_enable: fan_config = data->fan_config[channel];
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 37/50 hwmon: (max31790) Fix pwmX_enable attributes
In reply to Sasha LevinFrom: Guenter Roeck <[email protected]>
[ Upstream commit 148c847c9e5a54b99850617bf9c143af9a344f92 ]
pwmX_enable supports three possible values:
0: Fan control disabled. Duty cycle is fixed to 0% 1: Fan control enabled, pwm mode. Duty cycle is determined by
values written into Target Duty Cycle registers.
2: Fan control enabled, rpm mode
Duty cycle is adjusted such that fan speed matches the values in Target Count registers
The current code does not do this; instead, it mixes pwm control configuration with fan speed monitoring configuration. Worse, it reports that pwm control would be disabled (pwmX_enable==0) when it is in fact enabled in pwm mode. Part of the problem may be that the chip sets the "TACH input enable" bit on its own whenever the mode bit is set to RPM mode, but that doesn't mean that "TACH input enable" accurately reflects the pwm mode.
Fix it up and only handle pwm control with the pwmX_enable attributes. In the documentation, clarify that disabling pwm control (pwmX_enable=0) sets the pwm duty cycle to 0%. In the code, explain why TACH_INPUT_EN is set together with RPM_MODE.
While at it, only update the configuration register if the configuration has changed, and only update the cached configuration if updating the chip configuration was successful.
--- Documentation/hwmon/max31790.rst | 2 +- drivers/hwmon/max31790.c | 41 ++++++++++++++++++++------------ 2 files changed, 27 insertions(+), 16 deletions(-)
Documentation/hwmon/max31790.rst +1 -1
@@ -38,7 +38,7 @@ Sysfs entries fan[1-12]_input RO fan tachometer speed in RPM fan[1-12]_fault RO fan experienced fault fan[1-6]_target RW desired fan speed in RPM -pwm[1-6]_enable RW regulator mode, 0=disabled, 1=manual mode, 2=rpm mode +pwm[1-6]_enable RW regulator mode, 0=disabled (duty cycle=0%), 1=manual mode, 2=rpm mode pwm[1-6] RW read: current pwm duty cycle, write: target pwm duty cycle (0-255) ================== === =======================================================
drivers/hwmon/max31790.c +26 -15
67 lines not on this page · raw message
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 38/50 drivers/perf: fix the missed ida_simple_remove() in ddr_perf_probe()
In reply to Sasha LevinFrom: Jing Xiangfeng <[email protected]>
[ Upstream commit d96b1b8c9f79b6bb234a31c80972a6f422079376 ]
ddr_perf_probe() misses to call ida_simple_remove() in an error path. Jump to cpuhp_state_err to fix it.
--- drivers/perf/fsl_imx8_ddr_perf.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/perf/fsl_imx8_ddr_perf.c +4 -2
@@ -562,8 +562,10 @@ static int ddr_perf_probe(struct platform_device *pdev) name =devm_kasprintf (&pdev->dev,GFP_KERNEL ,DDR_PERF_DEV_NAME "%d" , num); -if (!name) -return -ENOMEM ; +if (!name) { + ret = -ENOMEM ; + goto cpuhp_state_err; + } pmu->devtype_data =of_device_get_match_data (&pdev->dev);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 39/50 KVM: PPC: Book3S HV: Fix TLB management on SMT8 POWER9 and POWER10 processors
In reply to Sasha LevinFrom: Suraj Jitindar Singh <[email protected]>
[ Upstream commit 77bbbc0cf84834ed130838f7ac1988567f4d0288 ]
The POWER9 vCPU TLB management code assumes all threads in a core share a TLB, and that TLBIEL execued by one thread will invalidate TLBs for all threads. This is not the case for SMT8 capable POWER9 and POWER10 (big core) processors, where the TLB is split between groups of threads. This results in TLB multi-hits, random data corruption, etc.
Fix this by introducing cpu_first_tlb_thread_sibling etc., to determine which siblings share TLBs, and use that in the guest TLB flushing code.
[[email protected]: add changelog and comment]
--- arch/powerpc/include/asm/cputhreads.h | 30 +++++++++++++++++++++++++++ arch/powerpc/kvm/book3s_hv.c | 13 ++++++------ arch/powerpc/kvm/book3s_hv_builtin.c | 2 +- arch/powerpc/kvm/book3s_hv_rm_mmu.c | 2 +- 4 files changed, 39 insertions(+), 8 deletions(-)
arch/powerpc/include/asm/cputhreads.h +30 -0
@@ -99,6 +99,36 @@ static inline int cpu_last_thread_sibling(int cpu)return cpu | (threads_per_core -1 ); } +/* +* tlb_thread_siblings are siblings which share a TLB. This is not +* architected, is not something a hypervisor could emulate and a future +* CPU may change behaviour even in compat mode, so this should only be +* used on PowerNV, and only with care. +*/ +static inline int cpu_first_tlb_thread_sibling (int cpu) +{ +if (cpu_has_feature (CPU_FTR_ARCH_300 ) && (threads_per_core =8 )) +return cpu & ~0x6 ;/* Big Core */ +else +return cpu_first_thread_sibling (cpu); +} + +static inline int cpu_last_tlb_thread_sibling (int cpu) +{ +if (cpu_has_feature (CPU_FTR_ARCH_300 ) && (threads_per_core =8 )) +return cpu |0x6 ;/* Big Core */ +else +return cpu_last_thread_sibling (cpu); +} + +static inline int cpu_tlb_thread_sibling_step (void ) +{ +if (cpu_has_feature (CPU_FTR_ARCH_300 ) && (threads_per_core =8 )) +return 2 ;/* Big Core */ +else +return 1 ; +} +static inline u32 get_tensr (void ) {#ifdef CONFIG_BOOKE
arch/powerpc/kvm/book3s_hv.c +6 -5
@@ -2536,7 +2536,7 @@ static void radix_flush_cpu(struct kvm *kvm, int cpu, struct kvm_vcpu *vcpu)cpumask_t *cpu_in_guest;int i; - cpu =cpu_first_thread_sibling (cpu); + cpu =cpu_first_tlb_thread_sibling (cpu);if (nested) {cpumask_set_cpu (cpu, &nested->need_tlb_flush); cpu_in_guest = &nested->cpu_in_guest;
@@ -2550,9 +2550,10 @@ static void radix_flush_cpu(struct kvm *kvm, int cpu, struct kvm_vcpu *vcpu)* the other side is the first smp_mb() in kvmppc_run_core(). */ smp_mb (); -for (i =0 ; i < threads_per_core; ++i) -if (cpumask_test_cpu (cpu + i, cpu_in_guest)) -smp_call_function_single (cpu + i, do_nothing,NULL ,1 ); +for (i = cpu; i <=cpu_last_tlb_thread_sibling (cpu); + i +=cpu_tlb_thread_sibling_step ()) +if (cpumask_test_cpu (i, cpu_in_guest)) +smp_call_function_single (i, do_nothing,NULL ,1 ); }static void kvmppc_prepare_radix_vcpu (struct kvm_vcpu *vcpu,int pcpu)
@@ -2583,8 +2584,8 @@ static void kvmppc_prepare_radix_vcpu(struct kvm_vcpu *vcpu, int pcpu)*/ if (prev_cpu != pcpu) {if (prev_cpu >=0 && - cpu_first_thread_sibling(prev_cpu) !- cpu_first_thread_sibling(pcpu)) + cpu_first_tlb_thread_sibling(prev_cpu) !+ cpu_first_tlb_thread_sibling(pcpu))radix_flush_cpu (kvm, prev_cpu, vcpu);if (nested) nested->prev_cpu[vcpu->arch.nested_vcpu_id] = pcpu;
arch/powerpc/kvm/book3s_hv_builtin.c +1 -1
@@ -847,7 +847,7 @@ void kvmppc_check_need_tlb_flush(struct kvm *kvm, int pcpu,* Thus we make all 4 threads use the same bit. */ if (cpu_has_feature (CPU_FTR_ARCH_300 )) - pcpu =cpu_first_thread_sibling (pcpu); + pcpu =cpu_first_tlb_thread_sibling (pcpu);if (nested) need_tlb_flush = &nested->need_tlb_flush;
arch/powerpc/kvm/book3s_hv_rm_mmu.c +1 -1
@@ -67,7 +67,7 @@ static int global_invalidates(struct kvm *kvm)* so use the bit for the first thread to represent the core. */ if (cpu_has_feature (CPU_FTR_ARCH_300 )) - cpu =cpu_first_thread_sibling (cpu); + cpu =cpu_first_tlb_thread_sibling (cpu);cpumask_clear_cpu (cpu, &kvm->arch.need_tlb_flush); }
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 40/50 btrfs: fix error handling in __btrfs_update_delayed_inode
In reply to Sasha LevinFrom: Josef Bacik <[email protected]>
[ Upstream commit bb385bedded3ccbd794559600de4a09448810f4a ]
If we get an error while looking up the inode item we'll simply bail without cleaning up the delayed node. This results in this style of warning happening on commit:
WARNING: CPU: 0 PID: 76403 at fs/btrfs/delayed-inode.c:1365 btrfs_assert_delayed_root_empty+0x5b/0x90 CPU: 0 PID: 76403 Comm: fsstress Tainted: G W 5.13.0-rc1+ #373 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014 RIP: 0010:btrfs_assert_delayed_root_empty+0x5b/0x90 RSP: 0018:ffffb8bb815a7e50 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff95d6d07e1888 RCX: ffff95d6c0fa3000 RDX: 0000000000000002 RSI: 000000000029e91c RDI: ffff95d6c0fc8060 RBP: ffff95d6c0fc8060 R08: 00008d6d701a2c1d R09: 0000000000000000 R10: ffff95d6d1760ea0 R11: 0000000000000001 R12: ffff95d6c15a4d00 R13: ffff95d6c0fa3000 R14: 0000000000000000 R15: ffffb8bb815a7e90 FS: 00007f490e8dbb80(0000) GS:ffff95d73bc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f6e75555cb0 CR3: 00000001101ce001 CR4: 0000000000370ef0 Call Trace: btrfs_commit_transaction+0x43c/0xb00 ? finish_wait+0x80/0x80 ? vfs_fsync_range+0x90/0x90 iterate_supers+0x8c/0x100 ksys_sync+0x50/0x90 __do_sys_sync+0xa/0x10 do_syscall_64+0x3d/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae
Because the iref isn't dropped and this leaves an elevated node->count, so any release just re-queues it onto the delayed inodes list. Fix this by going to the out label to handle the proper cleanup of the delayed node.
--- fs/btrfs/delayed-inode.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-)
fs/btrfs/delayed-inode.c +4 -6
@@ -1033,12 +1033,10 @@ static int __btrfs_update_delayed_inode(struct btrfs_trans_handle *trans, nofs_flag =memalloc_nofs_save (); ret =btrfs_lookup_inode (trans, root, path, &key, mod);memalloc_nofs_restore (nofs_flag); -if (ret >0 ) { -btrfs_release_path (path); -return -ENOENT ; - }else if (ret <0 ) { -return ret; - } +if (ret >0 ) + ret = -ENOENT ; +if (ret <0 ) + goto out; leaf = path->nodes[0 ]; inode_item = btrfs_item_ptr(leaf, path->slots[0],
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 41/50 btrfs: abort transaction if we fail to update the delayed inode
In reply to Sasha LevinFrom: Josef Bacik <[email protected]>
[ Upstream commit 04587ad9bef6ce9d510325b4ba9852b6129eebdb ]
If we fail to update the delayed inode we need to abort the transaction, because we could leave an inode with the improper counts or some other such corruption behind.
--- fs/btrfs/delayed-inode.c | 8 ++++++++ 1 file changed, 8 insertions(+)
fs/btrfs/delayed-inode.c +8 -0
@@ -1074,6 +1074,14 @@ static int __btrfs_update_delayed_inode(struct btrfs_trans_handle *trans,btrfs_delayed_inode_release_metadata (fs_info, node, (ret <0 ));btrfs_release_delayed_inode (node); +/* +* If we fail to update the delayed inode we need to abort the +* transaction, because we could leave the inode with the improper +* counts behind. +*/ +if (ret && ret != -ENOENT ) +btrfs_abort_transaction (trans, ret); +return ret; search:
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 42/50 btrfs: make Private2 lifespan more consistent
In reply to Sasha LevinFrom: Qu Wenruo <[email protected]>
[ Upstream commit 87b4d86baae219a9a79f6b0a1434b2a42fd40d09 ]
Currently we use page Private2 bit to indicate that we have ordered extent for the page range.
But the lifespan of it is not consistent, during regular writeback path, there are two locations to clear the same PagePrivate2:
T ----- Page marked Dirty
|
+ ----- Page marked Private2, through btrfs_run_dealloc_range() |
+ ----- Page cleared Private2, through btrfs_writepage_cow_fixup()
| in __extent_writepage_io()
| ^^^ Private2 cleared for the first time
|
+ ----- Page marked Writeback, through btrfs_set_range_writeback()
| in __extent_writepage_io().
|
+ ----- Page cleared Private2, through
| btrfs_writepage_endio_finish_ordered()
| ^^^ Private2 cleared for the second time.
|
+ ----- Page cleared Writeback, through btrfs_writepage_endio_finish_ordered()
Currently PagePrivate2 is mostly to prevent ordered extent accounting being executed for both endio and invalidatepage.
Thus only the one who cleared page Private2 is responsible for ordered extent accounting.
But the fact is, in btrfs_writepage_endio_finish_ordered(), page Private2 is cleared and ordered extent accounting is executed unconditionally.
The race prevention only happens through btrfs_invalidatepage(), where we wait for the page writeback first, before checking the Private2 bit.
This means, Private2 is also protected by Writeback bit, and there is no need for btrfs_writepage_cow_fixup() to clear Priavte2.
This patch will change btrfs_writepage_cow_fixup() to just check PagePrivate2, not to clear it.
The clearing will happen in either btrfs_invalidatepage() or btrfs_writepage_endio_finish_ordered().
This makes the Private2 bit easier to understand, just meaning the page has unfinished ordered extent attached to it.
And this patch is a hard requirement for the incoming refactoring for how we finished ordered IO for endio context, as the coming patch will check Private2 to determine if we need to do the ordered extent accounting. Thus this patch is definitely needed or we will hang due to unfinished ordered extent.
--- fs/btrfs/inode.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
fs/btrfs/inode.c +1 -1
@@ -2406,7 +2406,7 @@ int btrfs_writepage_cow_fixup(struct page *page, u64 start, u64 end)struct btrfs_writepage_fixup *fixup;/* this page is properly in the ordered list */ -if (TestClearPagePrivate2 (page)) +if (PagePrivate2 (page))return 0 ;/*
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 43/50 btrfs: fix the filemap_range_has_page() call in btrfs_punch_hole_lock_range()
In reply to Sasha LevinFrom: Qu Wenruo <[email protected]>
[ Upstream commit 0528476b6ac7832f31e2ed740a57ae31316b124e ]
[BUG]
With current subpage RW support, the following script can hang the fs with 64K page size.
# mkfs.btrfs -f -s 4k $dev # mount $dev -o nospace_cache $mnt # fsstress -w -n 50 -p 1 -s 1607749395 -d $mnt
The kernel will do an infinite loop in btrfs_punch_hole_lock_range().
[CAUSE]
In btrfs_punch_hole_lock_range() we:
- Truncate page cache range
- Lock extent io tree
- Wait any ordered extents in the range.
We exit the loop until we meet all the following conditions:
- No ordered extent in the lock range
- No page is in the lock range
The latter condition has a pitfall, it only works for sector size == PAGE_SIZE case.
While can't handle the following subpage case:
0 32K 64K 96K 128K | |///////||//////| ||
lockstart=32K
lockend=96K - 1
In this case, although the range crosses 2 pages, truncate_pagecache_range() will invalidate no page at all, but only zero the [32K, 96K) range of the two pages.
Thus filemap_range_has_page(32K, 96K-1) will always return true, thus we will never meet the loop exit condition.
[FIX]
Fix the problem by doing page alignment for the lock range.
Function filemap_range_has_page() has already handled lend < lstart case, we only need to round up @lockstart, and round_down @lockend for truncate_pagecache_range().
This modification should not change any thing for sector size == PAGE_SIZE case, as in that case our range is already page aligned.
--- fs/btrfs/file.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)
fs/btrfs/file.c +12 -1
@@ -2439,6 +2439,17 @@ static int btrfs_punch_hole_lock_range(struct inode *inode, const u64 lockend, struct extent_state **cached_state) { +/* +* For subpage case, if the range is not at page boundary, we could +* have pages at the leading/tailing part of the range. +* This could lead to dead loop since filemap_range_has_page() +* will always return true. +* So here we need to do extra page alignment for +* filemap_range_has_page(). +*/ +const u64 page_lockstart =round_up (lockstart,PAGE_SIZE ); +const u64 page_lockend =round_down (lockend +1 ,PAGE_SIZE ) -1 ; +while (1 ) {struct btrfs_ordered_extent *ordered;int ret;
@@ -2458,7 +2469,7 @@ static int btrfs_punch_hole_lock_range(struct inode *inode, (ordered->file_offset + ordered->len <= lockstart || ordered->file_offset > lockend)) && !filemap_range_has_page(inode->i_mapping, - lockstart, lockend)) { + page_lockstart, page_lockend)) {if (ordered)btrfs_put_ordered_extent (ordered);break ;
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 44/50 btrfs: disable build on platforms having page size 256K
In reply to Sasha LevinFrom: Christophe Leroy <[email protected]>
[ Upstream commit b05fbcc36be1f8597a1febef4892053a0b2f3f60 ]
With a config having PAGE_SIZE set to 256K, BTRFS build fails with the following message
include/linux/compiler_types.h:326:38: error: call to '__compiletime_assert_791' declared with attribute error:
BUILD_BUG_ON failed: (BTRFS_MAX_COMPRESSED % PAGE_SIZE) != 0
BTRFS_MAX_COMPRESSED being 128K, BTRFS cannot support platforms with 256K pages at the time being.
There are two platforms that can select 256K pages:
- hexagon
- powerpc
Disable BTRFS when 256K page size is selected. Supporting this would require changes to the subpage mode that's currently being developed. Given that 256K is many times larger than page sizes commonly used and for what the algorithms and structures have been tuned, it's out of scope and disabling build is a reasonable option.
--- fs/btrfs/Kconfig | 2 ++ 1 file changed, 2 insertions(+)
fs/btrfs/Kconfig +2 -0
@@ -14,6 +14,8 @@ config BTRFS_FS select RAID6_PQ select XOR_BLOCKS select SRCU + depends on !PPC_256K_PAGES # powerpc + depends on !PAGE_SIZE_256KB # hexagon help Btrfs is a general purpose copy-on-write filesystem with extents,
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 45/50 locking/lockdep: Fix the dep path printing for backwards BFS
In reply to Sasha LevinFrom: Boqun Feng <[email protected]>
[ Upstream commit 69c7a5fb2482636f525f016c8333fdb9111ecb9d ]
We use the same code to print backwards lock dependency path as the forwards lock dependency path, and this could result into incorrect printing because for a backwards lock_list ->trace is not the call trace where the lock of ->class is acquired.
Fix this by introducing a separate function on printing the backwards dependency path. Also add a few comments about the printing while we are at it.
--- kernel/locking/lockdep.c | 108 ++++++++++++++++++++++++++++++++++++++- 1 file changed, 106 insertions(+), 2 deletions(-)
kernel/locking/lockdep.c +106 -2
@@ -1941,7 +1941,56 @@ static void print_lock_class_header(struct lock_class *class, int depth) }/* -* printk the shortest lock dependencies from @start to @end in reverse order: +* Dependency path printing: +* +* After BFS we get a lock dependency path (linked via ->parent of lock_list), +* printing out each lock in the dependency path will help on understanding how +* the deadlock could happen. Here are some details about dependency path +* printing: +* +* 1) A lock_list can be either forwards or backwards for a lock dependency, +* for a lock dependency A -> B, there are two lock_lists: +* +* a) lock_list in the ->locks_after list of A, whose ->class is B and +* ->links_to is A. In this case, we can say the lock_list is +* "A -> B" (forwards case). +* +* b) lock_list in the ->locks_before list of B, whose ->class is A +* and ->links_to is B. In this case, we can say the lock_list is +* "B <- A" (bacwards case). +* +* The ->trace of both a) and b) point to the call trace where B was +* acquired with A held. +* +* 2) A "helper" lock_list is introduced during BFS, this lock_list doesn't +* represent a certain lock dependency, it only provides an initial entry +* for BFS. For example, BFS may introduce a "helper" lock_list whose +* ->class is A, as a result BFS will search all dependencies starting with +* A, e.g. A -> B or A -> C. +* +* The notation of a forwards helper lock_list is like "-> A", which means +* we should search the forwards dependencies starting with "A", e.g A -> B +* or A -> C. +* +* The notation of a bacwards helper lock_list is like "<- B", which means +* we should search the backwards dependencies ending with "B", e.g. +* B <- A or B <- C. +*/ + +/* +* printk the shortest lock dependencies from @root to @leaf in reverse order. +* +* We have a lock dependency path as follow: +* +* @root @leaf +* | | +* V V +* ->parent ->parent +* | lock_list | <--------- | lock_list | ... | lock_list | <--------- | lock_list | +* | -> L1 | | L1 -> L2 | ... |Ln-2 -> Ln-1| | Ln-1 -> Ln| +* +* , so it's natural that we start from @leaf and print every ->class and +* ->trace until we reach the @root. */ static void __used print_shortest_lock_dependencies(struct lock_list *leaf,
@@ -1969,6 +2018,61 @@ print_shortest_lock_dependencies(struct lock_list *leaf, }while (entry && (depth >=0 )); } +/* +* printk the shortest lock dependencies from @leaf to @root. +* +* We have a lock dependency path (from a backwards search) as follow: +* +* @leaf @root +* | | +* V V +* ->parent ->parent +* | lock_list | ---------> | lock_list | ... | lock_list | ---------> | lock_list | +* | L2 <- L1 | | L3 <- L2 | ... | Ln <- Ln-1 | | <- Ln | +* +* , so when we iterate from @leaf to @root, we actually print the lock +* dependency path L1 -> L2 -> .. -> Ln in the non-reverse order. +* +* Another thing to notice here is that ->class of L2 <- L1 is L1, while the +* ->trace of L2 <- L1 is the call trace of L2, in fact we don't have the call +* trace of L1 in the dependency path, which is alright, because most of the +* time we can figure out where L1 is held from the call trace of L2. +*/ +static void __used +print_shortest_lock_dependencies_backwards (struct lock_list *leaf, +struct lock_list *root) +{ +struct lock_list *entry = leaf; +const struct lock_trace *trace =NULL ; +int depth; + +/*compute depth from generated tree by BFS*/ + depth =get_lock_depth (leaf); + +do { +print_lock_class_header (entry->class, depth); +if (trace) { +printk ("%*s ... acquired at:\n" , depth,"" ); +print_lock_trace (trace,2 ); +printk ("\n" ); + } + +/* +* Record the pointer to the trace for the next lock_list +* entry, see the comments for the function. +*/ + trace = entry->trace; + +if (depth ==0 && (entry != root)) { +printk ("lockdep:%s bad path found in chain graph\n" , __func__); +break ; + } + + entry =get_lock_parent (entry); + depth--; + }while (entry && (depth >=0 )); +} + static void print_irq_lock_scenario(struct lock_list *safe_entry, struct lock_list *unsafe_entry,
@@ -2086,7 +2190,7 @@ print_bad_irq_dependency(struct task_struct *curr, prev_root->trace =save_trace ();if (!prev_root->trace)return ; -print_shortest_lock_dependencies (backwards_entry, prev_root); +print_shortest_lock_dependencies_backwards (backwards_entry, prev_root);pr_warn ("\nthe dependencies between the lock to be acquired" );pr_warn (" and %s-irq-unsafe lock:\n" , irqclass);
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 46/50 lockding/lockdep: Avoid to find wrong lock dep path in check_irq_usage()
In reply to Sasha LevinFrom: Boqun Feng <[email protected]>
[ Upstream commit 7b1f8c6179769af6ffa055e1169610b51d71edd5 ]
In the step #3 of check_irq_usage(), we seach backwards to find a lock whose usage conflicts the usage of @target_entry1 on safe/unsafe. However, we should only keep the irq-unsafe usage of @target_entry1 into consideration, because it could be a case where a lock is hardirq-unsafe but soft-safe, and in check_irq_usage() we find it because its hardirq-unsafe could result into a hardirq-safe-unsafe deadlock, but currently since we don't filter out the other usage bits, so we may find a lock dependency path softirq-unsafe -> softirq-safe, which in fact doesn't cause a deadlock. And this may cause misleading lockdep splats.
Fix this by only keeping LOCKF_ENABLED_IRQ_ALL bits when we try the backwards search.
--- kernel/locking/lockdep.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-)
kernel/locking/lockdep.c +11 -1
@@ -2377,8 +2377,18 @@ static int check_irq_usage(struct task_struct *curr, struct held_lock *prev,* Step 3: we found a bad match! Now retrieve a lock from the backward * list whose usage mask matches the exclusive usage mask from the * lock found on the forward list. +* +* Note, we should only keep the LOCKF_ENABLED_IRQ_ALL bits, considering +* the follow case: +* +* When trying to add A -> B to the graph, we find that there is a +* hardirq-safe L, that L -> ... -> A, and another hardirq-unsafe M, +* that B -> ... -> M. However M is **softirq-safe**, if we use exact +* invert bits of M's usage_mask, we will find another lock N that is +* **softirq-unsafe** and N -> ... -> A, however N -> .. -> M will not +* cause a inversion deadlock. */ - backward_mask =original_mask (target_entry1->class->usage_mask); + backward_mask =original_mask (target_entry1->class->usage_mask &LOCKF_ENABLED_IRQ_ALL ); ret =find_usage_backwards (&this, backward_mask, &target_entry);if (ret <0 ) {
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 47/50 KVM: s390: get rid of register asm usage
In reply to Sasha LevinFrom: Heiko Carstens <[email protected]>
[ Upstream commit 4fa3b91bdee1b08348c82660668ca0ca34e271ad ]
Using register asm statements has been proven to be very error prone, especially when using code instrumentation where gcc may add function calls, which clobbers register contents in an unexpected way.
Therefore get rid of register asm statements in kvm code, even though there is currently nothing wrong with them. This way we know for sure that this bug class won't be introduced here.
--- arch/s390/kvm/kvm-s390.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)
arch/s390/kvm/kvm-s390.c +9 -9
@@ -318,31 +318,31 @@ static void allow_cpu_feat(unsigned long nr)static inline int plo_test_bit (unsigned char nr) { - register unsigned long r0 asm("0") = (unsigned long) nr | 0x100; +unsigned long function = (unsigned long )nr |0x100 ;int cc; asmvolatile ( +" lgr 0,%[function]\n" /* Parameter registers are ignored for "test bit" */ " plo 0,0,0,0(0)\n" " ipm %0\n" " srl %0,28\n" :"=d" (cc) - :"d" (r0) - :"cc" ); + : [function]"d" (function) + :"cc" ,"0" );return cc ==0 ; } static __always_inline void __insn32_query(unsigned int opcode, u8 *query) { - register unsigned long r0 asm("0") = 0; /* query function */ - register unsigned long r1 asm("1") = (unsigned long) query; - asmvolatile ( -/* Parameter regs are ignored */ +" lghi 0,0\n" +" lgr 1,%[query]\n" +/* Parameter registers are ignored */ " .insn rrf,%[opc] << 16,2,4,6,0\n" : - :"d" (r0),"a" (r1), [opc]"i" (opcode) - :"cc" ,"memory" ); + : [query]"d" ((unsigned long )query), [opc]"i" (opcode) + :"cc" ,"memory" ,"0" ,"1" ); }#define INSN_SORTL 0xb938
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 48/50 regulator: mt6358: Fix vdram2 .vsel_mask
In reply to Sasha LevinFrom: Hsin-Hsiung Wang <[email protected]>
[ Upstream commit 50c9462edcbf900f3d5097ca3ad60171346124de ]
The valid vsel value are 0 and 12, so the .vsel_mask should be 0xf.
--- drivers/regulator/mt6358-regulator.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/regulator/mt6358-regulator.c +1 -1
@@ -457,7 +457,7 @@ static struct mt6358_regulator_info mt6358_regulators[] = {MT6358_REG_FIXED ("ldo_vaud28" ,VAUD28 ,MT6358_LDO_VAUD28_CON0 ,0 ,2800000 ),MT6358_LDO ("ldo_vdram2" ,VDRAM2 , vdram2_voltages, vdram2_idx, -MT6358_LDO_VDRAM2_CON0 ,0 ,MT6358_LDO_VDRAM2_ELR0 ,0x10 ,0 ), +MT6358_LDO_VDRAM2_CON0 ,0 ,MT6358_LDO_VDRAM2_ELR0 ,0xf ,0 ),MT6358_LDO ("ldo_vsim1" ,VSIM1 , vsim_voltages, vsim_idx,MT6358_LDO_VSIM1_CON0 ,0 ,MT6358_VSIM1_ANA_CON0 ,0xf00 ,8 ), MT6358_LDO("ldo_vibr", VIBR, vibr_voltages, vibr_idx,
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 49/50 regulator: da9052: Ensure enough delay time for .set_voltage_time_sel
In reply to Sasha LevinFrom: Axel Lin <[email protected]>
[ Upstream commit a336dc8f683e5be794186b5643cd34cb28dd2c53 ]
Use DIV_ROUND_UP to prevent truncation by integer division issue. This ensures we return enough delay time.
Also fix returning negative value when new_sel < old_sel.
--- drivers/regulator/da9052-regulator.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/regulator/da9052-regulator.c +2 -1
@@ -250,7 +250,8 @@ static int da9052_regulator_set_voltage_time_sel(struct regulator_dev *rdev,case DA9052_ID_BUCK3 :case DA9052_ID_LDO2 :case DA9052_ID_LDO3 : - ret = (new_sel - old_sel) * info->step_uV /6250 ; + ret =DIV_ROUND_UP (abs (new_sel - old_sel) * info->step_uV, +6250 );break ; }
Signature · 1 line
2.30.2
Sasha Levin
maintainerPATCH 50/50 media: Fix Media Controller API config checks
In reply to Sasha LevinFrom: Shuah Khan <[email protected]>
[ Upstream commit 50e7a31d30e8221632675abed3be306382324ca2 ]
Smatch static checker warns that "mdev" can be null:
sound/usb/media.c:287 snd_media_device_create()
warn: 'mdev' can also be NULL
If CONFIG_MEDIA_CONTROLLER is disabled, this file should not be included in the build.
The below conditions in the sound/usb/Makefile are in place to ensure that media.c isn't included in the build.
sound/usb/Makefile:
snd-usb-audio-$(CONFIG_SND_USB_AUDIO_USE_MEDIA_CONTROLLER) += media.o
select SND_USB_AUDIO_USE_MEDIA_CONTROLLER if MEDIA_CONTROLLER &&
(MEDIA_SUPPORT=y || MEDIA_SUPPORT=SND_USB_AUDIO)
The following config check in include/media/media-dev-allocator.h is in place to enable the API only when CONFIG_MEDIA_CONTROLLER and CONFIG_USB are enabled.
#if defined(CONFIG_MEDIA_CONTROLLER) && defined(CONFIG_USB)
This check doesn't work as intended when CONFIG_USB=m. When CONFIG_USB=m, CONFIG_USB_MODULE is defined and CONFIG_USB is not. The above config check doesn't catch that CONFIG_USB is defined as a module and disables the API. This results in sound/usb enabling Media Controller specific ALSA driver code, while Media disables the Media Controller API.
Fix the problem requires two changes:
1. Change the check to use IS_ENABLED to detect when CONFIG_USB is enabled as a module or static. Since CONFIG_MEDIA_CONTROLLER is a bool, leave the check unchanged to be consistent with drivers/media/Makefile.
2. Change the drivers/media/mc/Makefile to include mc-dev-allocator.o in mc-objs when CONFIG_USB is enabled.
--- drivers/media/mc/Makefile | 2 +- include/media/media-dev-allocator.h | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/media/mc/Makefile +1 -1
@@ -3,7 +3,7 @@ mc-objs := mc-device.o mc-devnode.o mc-entity.o \ mc-request.o -ifeq ($(CONFIG_USB),y) +ifneq ($(CONFIG_USB),) mc-objs += mc-dev-allocator.o endif
include/media/media-dev-allocator.h +1 -1
@@ -19,7 +19,7 @@struct usb_device ; -#if defined(CONFIG_MEDIA_CONTROLLER ) && defined(CONFIG_USB ) +#if defined(CONFIG_MEDIA_CONTROLLER ) &&IS_ENABLED (CONFIG_USB )/** * media_device_usb_allocate() - Allocate and return struct &media device *
Signature · 1 line
2.30.2