Skip to contentSkip to conversation

spi: Make of_register_spi_device also set the fwnode

PATCH New Sasha Levin 1 participant 31 messages Jul 4, 2021

Subsystems (7)
lore
Share & tools
lore

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/31 spi: Make of_register_spi_device also set the fwnode

From: Charles Keepax <[email protected]>

[ Upstream commit 0e793ba77c18382f08e440260fe72bc6fce2a3cb ]

Currently, the SPI core doesn't set the struct device fwnode pointer when it creates a new SPI device. This means when the device is registered the fwnode is NULL and the check in device_add which sets the fwnode->dev pointer is skipped. This wasn't previously an issue, however these two patches:

commit 4731210c09f5 ("gpiolib: Bind gpio_device to a driver to enable fw_devlink=on by default")
commit ced2af419528 ("gpiolib: Don't probe gpio_device if it's not the primary device")

Added some code to the GPIO core which relies on using that fwnode->dev pointer to determine if a driver is bound to the fwnode and if not bind a stub GPIO driver. This means the GPIO providers behind SPI will get both the expected driver and this stub driver causing the stub driver to fail if it attempts to request any pin configuration. For example on my system:

madera-pinctrl madera-pinctrl: pin gpio5 already requested by madera-pinctrl; cannot claim for gpiochip3 madera-pinctrl madera-pinctrl: pin-4 (gpiochip3) status -22
madera-pinctrl madera-pinctrl: could not request pin 4 (gpio5) from group aif1 on device madera-pinctrl gpio_stub_drv gpiochip3: Error applying setting, reverse things back
gpio_stub_drv: probe of gpiochip3 failed with error -22

The firmware node on the device created by the GPIO framework is set through the of_node pointer hence things generally actually work, however that fwnode->dev is never set, as the check was skipped at device_add time. This fix appears to match how the I2C subsystem handles the same situation.

---
 drivers/spi/spi.c | 1 +
 1 file changed, 1 insertion(+)
drivers/spi/spi.c +1 -0
index bbe33016d371..49f592e433a8 100644
@@ -1678,6 +1678,7 @@ of_register_spi_device(struct spi_controller *ctlr, struct device_node *nc)
 	/* Store a pointer to the node in the device structure */
 	of_node_get(nc);
 	spi->dev.of_node = nc;
+	spi->dev.fwnode = of_fwnode_handle(nc);
 
 	/* Register the new device */
 	rc = spi_add_device(spi);
Signature · 1 line
2.30.2
author maintainer
#1 lore raw

PATCH 2/31 media: s5p: fix pm_runtime_get_sync() usage count

From: Mauro Carvalho Chehab <[email protected]>

[ Upstream commit fdc34e82c0f968ac4c157bd3d8c299ebc24c9c63 ]

The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.

While here, check if the PM runtime error was caught at s5p_cec_adap_enable().

---
 drivers/media/platform/s5p-cec/s5p_cec.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/media/platform/s5p-cec/s5p_cec.c +4 -1
index 8837e2678bde..fe78292df8a6 100644
@@ -39,10 +39,13 @@ MODULE_PARM_DESC(debug, "debug level (0-2)");
 
 static int s5p_cec_adap_enable(struct cec_adapter *adap, bool enable)
 {
+	int ret;
 	struct s5p_cec_dev *cec = cec_get_drvdata(adap);
 
 	if (enable) {
-		pm_runtime_get_sync(cec->dev);
+		ret = pm_runtime_resume_and_get(cec->dev);
+		if (ret < 0)
+			return ret;
 
 		s5p_cec_reset(cec);
 
Signature · 1 line
2.30.2
author maintainer
#2 lore raw

PATCH 3/31 media: sh_vou: fix pm_runtime_get_sync() usage count

In reply to Sasha Levin

From: Mauro Carvalho Chehab <[email protected]>

[ Upstream commit 6e8b1526db164c9d4b9dacfb9bc48e365d7c4860 ]

The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.

While here, check if the PM runtime error was caught at open time.

---
 drivers/media/platform/sh_vou.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/media/platform/sh_vou.c +5 -1
index 6135e13e24d4..02d35e34694e 100644
@@ -1144,7 +1144,11 @@ static int sh_vou_open(struct file *file)
 	if (v4l2_fh_is_singular_file(file) &&
 	    vou_dev->status == SH_VOU_INITIALISING) {
 		/* First open */
-		pm_runtime_get_sync(vou_dev->v4l2_dev.dev);
+		err = pm_runtime_resume_and_get(vou_dev->v4l2_dev.dev);
+		if (err < 0) {
+			v4l2_fh_release(file);
+			goto done_open;
+		}
 		err = sh_vou_hw_init(vou_dev);
 		if (err < 0) {
 			pm_runtime_put(vou_dev->v4l2_dev.dev);
Signature · 1 line
2.30.2
author maintainer
#3 lore raw

PATCH 4/31 media: sti/bdisp: fix pm_runtime_get_sync() usage count

In reply to Sasha Levin

From: Mauro Carvalho Chehab <[email protected]>

[ Upstream commit c44eac5b72e23c31eefc0e10a71d9650036b8341 ]

The pm_runtime_get_sync() internally increments the dev->power.usage_count without decrementing it, even on errors.

The bdisp_start_streaming() doesn't take it into account, which would unbalance PM usage counter at bdisp_stop_streaming().

The logic at bdisp_probe() is correct, but the best is to use the same call along the driver.

So, replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.

---
 drivers/media/platform/sti/bdisp/bdisp-v4l2.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/media/platform/sti/bdisp/bdisp-v4l2.c +4 -3
index 00f6e3f06dac..1fb04dc0f7d0 100644
@@ -499,7 +499,7 @@ static int bdisp_start_streaming(struct vb2_queue *q, unsigned int count)
 {
 	struct bdisp_ctx *ctx = q->drv_priv;
 	struct vb2_v4l2_buffer *buf;
-	int ret = pm_runtime_get_sync(ctx->bdisp_dev->dev);
+	int ret = pm_runtime_resume_and_get(ctx->bdisp_dev->dev);
 
 	if (ret < 0) {
 		dev_err(ctx->bdisp_dev->dev, "failed to set runtime PM\n");
@@ -1368,10 +1368,10 @@ static int bdisp_probe(struct platform_device *pdev)
 
 	/* Power management */
 	pm_runtime_enable(dev);
-	ret = pm_runtime_get_sync(dev);
+	ret = pm_runtime_resume_and_get(dev);
 	if (ret < 0) {
 		dev_err(dev, "failed to set PM\n");
-		goto err_pm;
+		goto err_remove;
 	}
 
 	/* Filters */
@@ -1399,6 +1399,7 @@ static int bdisp_probe(struct platform_device *pdev)
 	bdisp_hw_free_filters(bdisp->dev);
 err_pm:
 	pm_runtime_put(dev);
+err_remove:
 	bdisp_debugfs_remove(bdisp);
 err_v4l2:
 	v4l2_device_unregister(&bdisp->v4l2_dev);
Signature · 1 line
2.30.2
author maintainer
#4 lore raw

PATCH 5/31 spi: spi-loopback-test: Fix 'tx_buf' might be 'rx_buf'

In reply to Sasha Levin

From: Jay Fang <[email protected]>

[ Upstream commit 9e37a3ab0627011fb63875e9a93094b6fc8ddf48 ]

In function 'spi_test_run_iter': Value 'tx_buf' might be 'rx_buf'.

---
 drivers/spi/spi-loopback-test.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-loopback-test.c +1 -1
index b9a7117b6dce..85d3475915dd 100644
@@ -877,7 +877,7 @@ static int spi_test_run_iter(struct spi_device *spi,
 		test.transfers[i].len = len;
 		if (test.transfers[i].tx_buf)
 			test.transfers[i].tx_buf += tx_off;
-		if (test.transfers[i].tx_buf)
+		if (test.transfers[i].rx_buf)
 			test.transfers[i].rx_buf += rx_off;
 	}
 
Signature · 1 line
2.30.2
author maintainer
#5 lore raw

PATCH 6/31 spi: spi-topcliff-pch: Fix potential double free in pch_spi_process_messages()

In reply to Sasha Levin

From: Jay Fang <[email protected]>

[ Upstream commit 026a1dc1af52742c5897e64a3431445371a71871 ]

pch_spi_set_tx() frees data->pkt_tx_buff on failure of kzalloc() for data->pkt_rx_buff, but its caller, pch_spi_process_messages(), will free data->pkt_tx_buff again. Set data->pkt_tx_buff to NULL after kfree() to avoid double free.

---
 drivers/spi/spi-topcliff-pch.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/spi/spi-topcliff-pch.c +3 -1
index 8a5966963834..ef19e050612c 100644
@@ -584,8 +584,10 @@ static void pch_spi_set_tx(struct pch_spi_data *data, int *bpw)
 	data->pkt_tx_buff = kzalloc(size, GFP_KERNEL);
 	if (data->pkt_tx_buff != NULL) {
 		data->pkt_rx_buff = kzalloc(size, GFP_KERNEL);
-		if (!data->pkt_rx_buff)
+		if (!data->pkt_rx_buff) {
 			kfree(data->pkt_tx_buff);
+			data->pkt_tx_buff = NULL;
+		}
 	}
 
 	if (!data->pkt_rx_buff) {
Signature · 1 line
2.30.2
author maintainer
#6 lore raw

PATCH 7/31 spi: omap-100k: Fix the length judgment problem

In reply to Sasha Levin

From: Tian Tao <[email protected]>

[ Upstream commit e7a1a3abea373e41ba7dfe0fbc93cb79b6a3a529 ]

word_len should be checked in the omap1_spi100k_setup_transfer function to see if it exceeds 32.

---
 drivers/spi/spi-omap-100k.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-omap-100k.c +1 -1
index 1eccdc4a4581..2eeb0fe2eed2 100644
@@ -251,7 +251,7 @@ static int omap1_spi100k_setup_transfer(struct spi_device *spi,
 	else
 		word_len = spi->bits_per_word;
 
-	if (spi->bits_per_word > 32)
+	if (word_len > 32)
 		return -EINVAL;
 	cs->word_len = word_len;
 
Signature · 1 line
2.30.2
author maintainer
#7 lore raw

PATCH 8/31 regulator: uniphier: Add missing MODULE_DEVICE_TABLE

In reply to Sasha Levin

From: Zou Wei <[email protected]>

[ Upstream commit d019f38a1af3c6015cde6a47951a3ec43beeed80 ]

This patch adds missing MODULE_DEVICE_TABLE definition which generates correct modalias for automatic loading of this driver when it is built as an external module.

---
 drivers/regulator/uniphier-regulator.c | 1 +
 1 file changed, 1 insertion(+)
drivers/regulator/uniphier-regulator.c +1 -0
index abf22acbd13e..a2e3654b6332 100644
@@ -197,6 +197,7 @@ static const struct of_device_id uniphier_regulator_match[] = {
 	},
 	{ /* Sentinel */ },
 };
+MODULE_DEVICE_TABLE(of, uniphier_regulator_match);
 
 static struct platform_driver uniphier_regulator_driver = {
 	.probe = uniphier_regulator_probe,
Signature · 1 line
2.30.2
author maintainer
#8 lore raw

PATCH 9/31 crypto: nx - add missing MODULE_DEVICE_TABLE

In reply to Sasha Levin

From: Bixuan Cui <[email protected]>

[ Upstream commit 06676aa1f455c74e3ad1624cea3acb9ed2ef71ae ]

This patch adds missing MODULE_DEVICE_TABLE definition which generates correct modalias for automatic loading of this driver when it is built as an external module.

---
 drivers/crypto/nx/nx-842-pseries.c | 1 +
 1 file changed, 1 insertion(+)
drivers/crypto/nx/nx-842-pseries.c +1 -0
index 66869976cfa2..fa40edae231e 100644
@@ -1086,6 +1086,7 @@ static const struct vio_device_id nx842_vio_driver_ids[] = {
 	{"ibm,compression-v1", "ibm,compression"},
 	{"", ""},
 };
+MODULE_DEVICE_TABLE(vio, nx842_vio_driver_ids);
 
 static struct vio_driver nx842_vio_driver = {
 	.name = KBUILD_MODNAME,
Signature · 1 line
2.30.2
author maintainer
#9 lore raw

PATCH 10/31 media: cpia2: fix memory leak in cpia2_usb_probe

In reply to Sasha Levin

From: Pavel Skripkin <[email protected]>

[ Upstream commit be8656e62e9e791837b606a027802b504a945c97 ]

syzbot reported leak in cpia2 usb driver. The problem was in invalid error handling.

v4l2_device_register() is called in cpia2_init_camera_struct(), but all error cases after cpia2_init_camera_struct() did not call the v4l2_device_unregister()

---
 drivers/media/usb/cpia2/cpia2.h      |  1 +
 drivers/media/usb/cpia2/cpia2_core.c | 12 ++++++++++++
 drivers/media/usb/cpia2/cpia2_usb.c  | 13 +++++++------
 3 files changed, 20 insertions(+), 6 deletions(-)
drivers/media/usb/cpia2/cpia2.h +1 -0
index ab238ac8bfc0..50c952250dc9 100644
@@ -438,6 +438,7 @@ int cpia2_send_command(struct camera_data *cam, struct cpia2_command *cmd);
 int cpia2_do_command(struct camera_data *cam,
 		     unsigned int command,
 		     unsigned char direction, unsigned char param);
+void cpia2_deinit_camera_struct(struct camera_data *cam, struct usb_interface *intf);
 struct camera_data *cpia2_init_camera_struct(struct usb_interface *intf);
 int cpia2_init_camera(struct camera_data *cam);
 int cpia2_allocate_buffers(struct camera_data *cam);
drivers/media/usb/cpia2/cpia2_core.c +12 -0
index 3dfbb545c0e3..42cce7e94101 100644
@@ -2172,6 +2172,18 @@ static void reset_camera_struct(struct camera_data *cam)
 	cam->height = cam->params.roi.height;
 }
 
+/******************************************************************************
+ *
+ *  cpia2_init_camera_struct
+ *
+ *  Deinitialize camera struct
+ *****************************************************************************/
+void cpia2_deinit_camera_struct(struct camera_data *cam, struct usb_interface *intf)
+{
+	v4l2_device_unregister(&cam->v4l2_dev);
+	kfree(cam);
+}
+
 /******************************************************************************
  *
  *  cpia2_init_camera_struct
drivers/media/usb/cpia2/cpia2_usb.c +7 -6
index 4c191fcd3a7f..839217574069 100644
@@ -853,15 +853,13 @@ static int cpia2_usb_probe(struct usb_interface *intf,
 	ret = set_alternate(cam, USBIF_CMDONLY);
 	if (ret < 0) {
 		ERR("%s: usb_set_interface error (ret = %d)\n", __func__, ret);
-		kfree(cam);
-		return ret;
+		goto alt_err;
 	}
 
 
 	if((ret = cpia2_init_camera(cam)) < 0) {
 		ERR("%s: failed to initialize cpia2 camera (ret = %d)\n", __func__, ret);
-		kfree(cam);
-		return ret;
+		goto alt_err;
 	}
 	LOG("  CPiA Version: %d.%02d (%d.%d)\n",
 	       cam->params.version.firmware_revision_hi,
@@ -881,11 +879,14 @@ static int cpia2_usb_probe(struct usb_interface *intf,
 	ret = cpia2_register_camera(cam);
 	if (ret < 0) {
 		ERR("%s: Failed to register cpia2 camera (ret = %d)\n", __func__, ret);
-		kfree(cam);
-		return ret;
+		goto alt_err;
 	}
 
 	return 0;
+
+alt_err:
+	cpia2_deinit_camera_struct(cam, intf);
+	return ret;
 }
 
 /******************************************************************************
Signature · 1 line
2.30.2
author maintainer
#10 lore raw

PATCH 11/31 media: cobalt: fix race condition in setting HPD

In reply to Sasha Levin

From: Hans Verkuil <[email protected]>

[ Upstream commit 3d37ef41bed0854805ab9af22c422267510e1344 ]

The cobalt_s_bit_sysctrl reads the old register value over PCI, then changes a bit and sets writes the new value to the register.

This is used among other things for setting the HPD output pin.

But if the HPD is changed for multiple inputs at the same time, then this causes a race condition where a stale value is read.

Serialize this function with a mutex.

---
 drivers/media/pci/cobalt/cobalt-driver.c | 1 +
 drivers/media/pci/cobalt/cobalt-driver.h | 7 ++++++-
 2 files changed, 7 insertions(+), 1 deletion(-)
drivers/media/pci/cobalt/cobalt-driver.c +1 -0
index 4885e833c052..f422558e6392 100644
@@ -675,6 +675,7 @@ static int cobalt_probe(struct pci_dev *pci_dev,
 		return -ENOMEM;
 	cobalt->pci_dev = pci_dev;
 	cobalt->instance = i;
+	mutex_init(&cobalt->pci_lock);
 
 	retval = v4l2_device_register(&pci_dev->dev, &cobalt->v4l2_dev);
 	if (retval) {
drivers/media/pci/cobalt/cobalt-driver.h +6 -1
index 429bee4ef79c..883093e5adea 100644
@@ -250,6 +250,8 @@ struct cobalt {
 	int instance;
 	struct pci_dev *pci_dev;
 	struct v4l2_device v4l2_dev;
+	/* serialize PCI access in cobalt_s_bit_sysctrl() */
+	struct mutex pci_lock;
 
 	void __iomem *bar0, *bar1;
 
@@ -319,10 +321,13 @@ static inline u32 cobalt_g_sysctrl(struct cobalt *cobalt)
 static inline void cobalt_s_bit_sysctrl(struct cobalt *cobalt,
 					int bit, int val)
 {
-	u32 ctrl = cobalt_read_bar1(cobalt, COBALT_SYS_CTRL_BASE);
+	u32 ctrl;
 
+	mutex_lock(&cobalt->pci_lock);
+	ctrl = cobalt_read_bar1(cobalt, COBALT_SYS_CTRL_BASE);
 	cobalt_write_bar1(cobalt, COBALT_SYS_CTRL_BASE,
 			(ctrl & ~(1UL << bit)) | (val << bit));
+	mutex_unlock(&cobalt->pci_lock);
 }
 
 static inline u32 cobalt_g_sysstat(struct cobalt *cobalt)
Signature · 1 line
2.30.2
author maintainer
#11 lore raw

PATCH 12/31 media: pvrusb2: fix warning in pvr2_i2c_core_done

In reply to Sasha Levin

From: Anirudh Rayabharam <[email protected]>

[ Upstream commit f8194e5e63fdcb349e8da9eef9e574d5b1d687cb ]

syzbot has reported the following warning in pvr2_i2c_done:

sysfs group 'power' not found for kobject '1-0043'

When the device is disconnected (pvr_hdw_disconnect), the i2c adapter is not unregistered along with the USB and v4l2 teardown. As part of the USB device disconnect, the sysfs files of the subdevices are also deleted. So, by the time pvr_i2c_core_done is called by pvr_context_destroy, the sysfs files have been deleted.

To fix this, unregister the i2c adapter too in pvr_hdw_disconnect. Make the device deregistration code shared by calling pvr_hdw_disconnect from pvr2_hdw_destroy.

---
 drivers/media/usb/pvrusb2/pvrusb2-hdw.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/media/usb/pvrusb2/pvrusb2-hdw.c +2 -2
index fcb201a40920..d1bbfe4000dd 100644
@@ -2668,9 +2668,8 @@ void pvr2_hdw_destroy(struct pvr2_hdw *hdw)
 		pvr2_stream_destroy(hdw->vid_stream);
 		hdw->vid_stream = NULL;
 	}
-	pvr2_i2c_core_done(hdw);
 	v4l2_device_unregister(&hdw->v4l2_dev);
-	pvr2_hdw_remove_usb_stuff(hdw);
+	pvr2_hdw_disconnect(hdw);
 	mutex_lock(&pvr2_unit_mtx);
 	do {
 		if ((hdw->unit_number >= 0) &&
@@ -2697,6 +2696,7 @@ void pvr2_hdw_disconnect(struct pvr2_hdw *hdw)
 {
 	pvr2_trace(PVR2_TRACE_INIT,"pvr2_hdw_disconnect(hdw=%p)",hdw);
 	LOCK_TAKE(hdw->big_lock);
+	pvr2_i2c_core_done(hdw);
 	LOCK_TAKE(hdw->ctl_lock);
 	pvr2_hdw_remove_usb_stuff(hdw);
 	LOCK_GIVE(hdw->ctl_lock);
Signature · 1 line
2.30.2
author maintainer
#12 lore raw

PATCH 13/31 crypto: qat - check return code of qat_hal_rd_rel_reg()

In reply to Sasha Levin

From: Jack Xu <[email protected]>

[ Upstream commit 96b57229209490c8bca4335b01a426a96173dc56 ]

Check the return code of the function qat_hal_rd_rel_reg() and return it to the caller.

This is to fix the following warning when compiling the driver with clang scan-build:

drivers/crypto/qat/qat_common/qat_hal.c:1436:2: warning: 6th function call argument is an uninitialized value

---
 drivers/crypto/qat/qat_common/qat_hal.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/crypto/qat/qat_common/qat_hal.c +5 -1
index dac130bb807a..eda692271f0c 100644
@@ -1256,7 +1256,11 @@ static int qat_hal_put_rel_wr_xfer(struct icp_qat_fw_loader_handle *handle,
 		pr_err("QAT: bad xfrAddr=0x%x\n", xfr_addr);
 		return -EINVAL;
 	}
-	qat_hal_rd_rel_reg(handle, ae, ctx, ICP_GPB_REL, gprnum, &gprval);
+	status = qat_hal_rd_rel_reg(handle, ae, ctx, ICP_GPB_REL, gprnum, &gprval);
+	if (status) {
+		pr_err("QAT: failed to read register");
+		return status;
+	}
 	gpr_addr = qat_hal_get_reg_addr(ICP_GPB_REL, gprnum);
 	data16low = 0xffff & data;
 	data16hi = 0xffff & (data >> 0x10);
Signature · 1 line
2.30.2
author maintainer
#13 lore raw

PATCH 14/31 crypto: qat - remove unused macro in FW loader

In reply to Sasha Levin

From: Jack Xu <[email protected]>

[ Upstream commit 9afe77cf25d9670e61b489fd52cc6f75fd7f6803 ]

Remove the unused macro ICP_DH895XCC_PESRAM_BAR_SIZE in the firmware loader.

This is to fix the following warning when compiling the driver using the clang compiler with CC=clang W=2:

drivers/crypto/qat/qat_common/qat_uclo.c:345:9: warning: macro is not used [-Wunused-macros]

---
 drivers/crypto/qat/qat_common/qat_uclo.c | 1 -
 1 file changed, 1 deletion(-)
drivers/crypto/qat/qat_common/qat_uclo.c +0 -1
index aeb03081415c..9542423bb7ca 100644
@@ -385,7 +385,6 @@ static int qat_uclo_init_umem_seg(struct icp_qat_fw_loader_handle *handle,
 	return 0;
 }
 
-#define ICP_DH895XCC_PESRAM_BAR_SIZE 0x80000
 static int qat_uclo_init_ae_memory(struct icp_qat_fw_loader_handle *handle,
 				   struct icp_qat_uof_initmem *init_mem)
 {
Signature · 1 line
2.30.2
author maintainer
#14 lore raw

PATCH 15/31 sched/fair: Fix ascii art by relpacing tabs

In reply to Sasha Levin

From: Odin Ugedal <[email protected]>

[ Upstream commit 08f7c2f4d0e9f4283f5796b8168044c034a1bfcb ]

When using something other than 8 spaces per tab, this ascii art makes not sense, and the reader might end up wondering what this advanced equation "is".

---
 kernel/sched/fair.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
kernel/sched/fair.c +4 -4
index acb34e9df551..9cdbc07bb70f 100644
@@ -2940,7 +2940,7 @@ void reweight_task(struct task_struct *p, int prio)
  *
  *                     tg->weight * grq->load.weight
  *   ge->load.weight = -----------------------------               (1)
- *			  \Sum grq->load.weight
+ *                       \Sum grq->load.weight
  *
  * Now, because computing that sum is prohibitively expensive to compute (been
  * there, done that) we approximate it with this average stuff. The average
@@ -2954,7 +2954,7 @@ void reweight_task(struct task_struct *p, int prio)
  *
  *                     tg->weight * grq->avg.load_avg
  *   ge->load.weight = ------------------------------              (3)
- *				tg->load_avg
+ *                             tg->load_avg
  *
  * Where: tg->load_avg ~= \Sum grq->avg.load_avg
  *
@@ -2970,7 +2970,7 @@ void reweight_task(struct task_struct *p, int prio)
  *
  *                     tg->weight * grq->load.weight
  *   ge->load.weight = ----------------------------- = tg->weight   (4)
- *			    grp->load.weight
+ *                         grp->load.weight
  *
  * That is, the sum collapses because all other CPUs are idle; the UP scenario.
  *
@@ -2989,7 +2989,7 @@ void reweight_task(struct task_struct *p, int prio)
  *
  *                     tg->weight * grq->load.weight
  *   ge->load.weight = -----------------------------		   (6)
- *				tg_load_avg'
+ *                             tg_load_avg'
  *
  * Where:
  *
Signature · 1 line
2.30.2
author maintainer
#15 lore raw

PATCH 16/31 media: em28xx: Fix possible memory leak of em28xx struct

In reply to Sasha Levin

From: Igor Matheus Andrade Torrente <[email protected]>

[ Upstream commit ac5688637144644f06ed1f3c6d4dd8bb7db96020 ]

The em28xx struct kref isn't being decreased after an error in the em28xx_ir_init, leading to a possible memory leak.

A kref_put and em28xx_shutdown_buttons is added to the error handler code.

---
 drivers/media/usb/em28xx/em28xx-input.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/media/usb/em28xx/em28xx-input.c +6 -2
index f84a1208d5d3..3612f0d730dd 100644
@@ -736,7 +736,8 @@ static int em28xx_ir_init(struct em28xx *dev)
 			dev->board.has_ir_i2c = 0;
 			dev_warn(&dev->intf->dev,
 				 "No i2c IR remote control device found.\n");
-			return -ENODEV;
+			err = -ENODEV;
+			goto ref_put;
 		}
 	}
 
@@ -751,7 +752,7 @@ static int em28xx_ir_init(struct em28xx *dev)
 
 	ir = kzalloc(sizeof(*ir), GFP_KERNEL);
 	if (!ir)
-		return -ENOMEM;
+		goto ref_put;
 	rc = rc_allocate_device(RC_DRIVER_SCANCODE);
 	if (!rc)
 		goto error;
@@ -862,6 +863,9 @@ static int em28xx_ir_init(struct em28xx *dev)
 	dev->ir = NULL;
 	rc_free_device(rc);
 	kfree(ir);
+ref_put:
+	em28xx_shutdown_buttons(dev);
+	kref_put(&dev->ref, em28xx_free_device);
 	return err;
 }
 
Signature · 1 line
2.30.2
author maintainer
#16 lore raw

PATCH 17/31 media: v4l2-core: Avoid the dangling pointer in v4l2_fh_release

In reply to Sasha Levin

From: Lv Yunlong <[email protected]>

[ Upstream commit 7dd0c9e547b6924e18712b6b51aa3cba1896ee2c ]

A use after free bug caused by the dangling pointer filp->privitate_data in v4l2_fh_release.
See https://lore.kernel.org/patchwork/patch/1419058/.

My patch sets the dangling pointer to NULL to provide robust.

---
 drivers/media/v4l2-core/v4l2-fh.c | 1 +
 1 file changed, 1 insertion(+)
drivers/media/v4l2-core/v4l2-fh.c +1 -0
index c91a7bd3ecfc..ac8282d059fc 100644
@@ -104,6 +104,7 @@ int v4l2_fh_release(struct file *filp)
 		v4l2_fh_del(fh);
 		v4l2_fh_exit(fh);
 		kfree(fh);
+		filp->private_data = NULL;
 	}
 	return 0;
 }
Signature · 1 line
2.30.2
author maintainer
#17 lore raw

PATCH 18/31 media: bt8xx: Fix a missing check bug in bt878_probe

In reply to Sasha Levin

From: Zheyu Ma <[email protected]>

[ Upstream commit 1a4520090681853e6b850cbe54b27247a013e0e5 ]

In 'bt878_irq', the driver calls 'tasklet_schedule', but this tasklet is set in 'dvb_bt8xx_load_card' of another driver 'dvb-bt8xx'. However, this two drivers are separate. The user may not load the 'dvb-bt8xx' driver when loading the 'bt8xx' driver, that is, the tasklet has not been initialized when 'tasklet_schedule' is called, so it is necessary to check whether the tasklet is initialized in 'bt878_probe'.

Fix this by adding a check at the end of bt878_probe.

The KASAN's report reveals it:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 800000006aab2067 P4D 800000006aab2067 PUD 6b2ea067 PMD 0
Oops: 0010 [#1] PREEMPT SMP KASAN PTI
CPU: 2 PID: 8724 Comm: syz-executor.0 Not tainted 4.19.177-
gdba4159c14ef-dirty #40
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-
gc9ba5276e321-prebuilt.qemu.org 04/01/2014
RIP: 0010:          (null)
Code: Bad RIP value.
RSP: 0018:ffff88806c287ea0 EFLAGS: 00010246
RAX: fffffbfff1b01774 RBX: dffffc0000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 1ffffffff1b01775 RDI: 0000000000000000
RBP: ffff88806c287f00 R08: fffffbfff1b01774 R09: fffffbfff1b01774
R10: 0000000000000001 R11: fffffbfff1b01773 R12: 0000000000000000
R13: ffff88806c29f530 R14: ffffffff8d80bb88 R15: ffffffff8d80bb90
FS:  00007f6b550e6700(0000) GS:ffff88806c280000(0000) knlGS:
0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 000000005ec98000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <IRQ>
 tasklet_action_common.isra.17+0x141/0x420 kernel/softirq.c:522
 tasklet_action+0x50/0x70 kernel/softirq.c:540
 __do_softirq+0x224/0x92c kernel/softirq.c:292
 invoke_softirq kernel/softirq.c:372 [inline]
 irq_exit+0x15a/0x180 kernel/softirq.c:412
 exiting_irq arch/x86/include/asm/apic.h:535 [inline]
 do_IRQ+0x123/0x1e0 arch/x86/kernel/irq.c:260
 common_interrupt+0xf/0xf arch/x86/entry/entry_64.S:670
 </IRQ>
RIP: 0010:__do_sys_interrupt kernel/sys.c:2593 [inline]
RIP: 0010:__se_sys_interrupt kernel/sys.c:2584 [inline]
RIP: 0010:__x64_sys_interrupt+0x5b/0x80 kernel/sys.c:2584
Code: ba 00 04 00 00 48 c7 c7 c0 99 31 8c e8 ae 76 5e 01 48 85 c0 75 21 e8

14 ae 24 00 48 c7 c3 c0 99 31 8c b8 0c 00 00 00 0f 01 c1 <31> db e8 fe ad 24 00 48 89 d8 5b 5d c3 48 c7 c3 ea ff ff ff eb ec
RSP: 0018:ffff888054167f10 EFLAGS: 00000212 ORIG_RAX: ffffffffffffffde
RAX: 000000000000000c RBX: ffffffff8c3199c0 RCX: ffffc90001ca6000
RDX: 000000000000001a RSI: ffffffff813478fc RDI: ffffffff8c319dc0
RBP: ffff888054167f18 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000080 R11: fffffbfff18633b7 R12: ffff888054167f58
R13: ffff88805f638000 R14: 0000000000000000 R15: 0000000000000000

 do_syscall_64+0xb0/0x4e0 arch/x86/entry/common.c:293
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x4692a9
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7

48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6b550e5c48 EFLAGS: 00000246 ORIG_RAX: 000000000000014f
RAX: ffffffffffffffda RBX: 000000000077bf60 RCX: 00000000004692a9
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020000140
RBP: 00000000004cf7eb R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000077bf60
R13: 0000000000000000 R14: 000000000077bf60 R15: 00007fff55a1dca0

Modules linked in:
Dumping ftrace buffer:
   (ftrace buffer empty)
CR2: 0000000000000000
---[ end trace 68e5849c3f77cbb6 ]---
RIP: 0010:          (null)
Code: Bad RIP value.
RSP: 0018:ffff88806c287ea0 EFLAGS: 00010246
RAX: fffffbfff1b01774 RBX: dffffc0000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 1ffffffff1b01775 RDI: 0000000000000000
RBP: ffff88806c287f00 R08: fffffbfff1b01774 R09: fffffbfff1b01774
R10: 0000000000000001 R11: fffffbfff1b01773 R12: 0000000000000000
R13: ffff88806c29f530 R14: ffffffff8d80bb88 R15: ffffffff8d80bb90
FS:  00007f6b550e6700(0000) GS:ffff88806c280000(0000) knlGS:
0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 000000005ec98000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
---
 drivers/media/pci/bt8xx/bt878.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/media/pci/bt8xx/bt878.c +3 -0
index f5f87e03f94b..855f8dc2a4ee 100644
@@ -494,6 +494,9 @@ static int bt878_probe(struct pci_dev *dev, const struct pci_device_id *pci_id)
 	btwrite(0, BT878_AINT_MASK);
 	bt878_num++;
 
+	if (!bt->tasklet.func)
+		tasklet_disable(&bt->tasklet);
+
 	return 0;
 
       fail2:
Signature · 1 line
2.30.2
author maintainer
#18 lore raw

PATCH 19/31 media: st-hva: Fix potential NULL pointer dereferences

In reply to Sasha Levin

From: Evgeny Novikov <[email protected]>

[ Upstream commit b7fdd208687ba59ebfb09b2199596471c63b69e3 ]

When ctx_id >= HVA_MAX_INSTANCES in hva_hw_its_irq_thread() it tries to access fields of ctx that is NULL at that point. The patch gets rid of these accesses.

Found by Linux Driver Verification project (linuxtesting.org).

---
 drivers/media/platform/sti/hva/hva-hw.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/media/platform/sti/hva/hva-hw.c +1 -2
index d826c011c095..6b852b0bb15a 100644
@@ -130,8 +130,7 @@ static irqreturn_t hva_hw_its_irq_thread(int irq, void *arg)
 	ctx_id = (hva->sts_reg & 0xFF00) >> 8;
 	if (ctx_id >= HVA_MAX_INSTANCES) {
 		dev_err(dev, "%s     %s: bad context identifier: %d\n",
-			ctx->name, __func__, ctx_id);
-		ctx->hw_err = true;
+			HVA_PREFIX, __func__, ctx_id);
 		goto out;
 	}
 
Signature · 1 line
2.30.2
author maintainer
#19 lore raw

PATCH 20/31 media: dvd_usb: memory leak in cinergyt2_fe_attach

In reply to Sasha Levin

From: Dongliang Mu <[email protected]>

[ Upstream commit 9ad1efee086e0e913914fa2b2173efb830bad68c ]

When the driver fails to talk with the hardware with dvb_usb_generic_rw, it will return an error to dvb_usb_adapter_frontend_init. However, the driver forgets to free the resource (e.g., struct cinergyt2_fe_state), which leads to a memory leak.

Fix this by freeing struct cinergyt2_fe_state when dvb_usb_generic_rw fails in cinergyt2_frontend_attach.

backtrace:

  [<0000000056e17b1a>] kmalloc include/linux/slab.h:552 [inline]
  [<0000000056e17b1a>] kzalloc include/linux/slab.h:682 [inline]
  [<0000000056e17b1a>] cinergyt2_fe_attach+0x21/0x80 drivers/media/usb/dvb-usb/cinergyT2-fe.c:271
  [<00000000ae0b1711>] cinergyt2_frontend_attach+0x21/0x70 drivers/media/usb/dvb-usb/cinergyT2-core.c:74
  [<00000000d0254861>] dvb_usb_adapter_frontend_init+0x11b/0x1b0 drivers/media/usb/dvb-usb/dvb-usb-dvb.c:290
  [<0000000002e08ac6>] dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:84 [inline]
  [<0000000002e08ac6>] dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:173 [inline]
  [<0000000002e08ac6>] dvb_usb_device_init.cold+0x4d0/0x6ae drivers/media/usb/dvb-usb/dvb-usb-init.c:287
---
 drivers/media/usb/dvb-usb/cinergyT2-core.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/media/usb/dvb-usb/cinergyT2-core.c +2 -0
index 6131aa7914a9..fb59dda7547a 100644
@@ -88,6 +88,8 @@ static int cinergyt2_frontend_attach(struct dvb_usb_adapter *adap)
 
 	ret = dvb_usb_generic_rw(d, st->data, 1, st->data, 3, 0);
 	if (ret < 0) {
+		if (adap->fe_adap[0].fe)
+			adap->fe_adap[0].fe->ops.release(adap->fe_adap[0].fe);
 		deb_rc("cinergyt2_power_ctrl() Failed to retrieve sleep state info\n");
 	}
 	mutex_unlock(&d->data_mutex);
Signature · 1 line
2.30.2
author maintainer
#20 lore raw

PATCH 21/31 mmc: via-sdmmc: add a check against NULL pointer dereference

In reply to Sasha Levin

From: Zheyu Ma <[email protected]>

[ Upstream commit 45c8ddd06c4b729c56a6083ab311bfbd9643f4a6 ]

Before referencing 'host->data', the driver needs to check whether it is null pointer, otherwise it will cause a null pointer reference.

This log reveals it:

[   29.355199] BUG: kernel NULL pointer dereference, address:
0000000000000014
[   29.357323] #PF: supervisor write access in kernel mode
[   29.357706] #PF: error_code(0x0002) - not-present page
[   29.358088] PGD 0 P4D 0
[   29.358280] Oops: 0002 [#1] PREEMPT SMP PTI
[   29.358595] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4-
g70e7f0549188-dirty #102
[   29.359164] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009),
BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[   29.359978] RIP: 0010:via_sdc_isr+0x21f/0x410
[   29.360314] Code: ff ff e8 84 aa d0 fd 66 45 89 7e 28 66 41 f7 c4 00
10 75 56 e8 72 aa d0 fd 66 41 f7 c4 00 c0 74 10 e8 65 aa d0 fd 48 8b 43
18 <c7> 40 14 ac ff ff ff e8 55 aa d0 fd 48 89 df e8 ad fb ff ff e9 77
[   29.361661] RSP: 0018:ffffc90000118e98 EFLAGS: 00010046
[   29.362042] RAX: 0000000000000000 RBX: ffff888107d77880
RCX: 0000000000000000
[   29.362564] RDX: 0000000000000000 RSI: ffffffff835d20bb
RDI: 00000000ffffffff
[   29.363085] RBP: ffffc90000118ed8 R08: 0000000000000001
R09: 0000000000000001
[   29.363604] R10: 0000000000000000 R11: 0000000000000001
R12: 0000000000008600
[   29.364128] R13: ffff888107d779c8 R14: ffffc90009c00200
R15: 0000000000008000
[   29.364651] FS:  0000000000000000(0000) GS:ffff88817bc80000(0000)
knlGS:0000000000000000
[   29.365235] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   29.365655] CR2: 0000000000000014 CR3: 0000000005a2e000
CR4: 00000000000006e0
[   29.366170] DR0: 0000000000000000 DR1: 0000000000000000
DR2: 0000000000000000
[   29.366683] DR3: 0000000000000000 DR6: 00000000fffe0ff0
DR7: 0000000000000400
[   29.367197] Call Trace:
[   29.367381]  <IRQ>
[   29.367537]  __handle_irq_event_percpu+0x53/0x3e0
[   29.367916]  handle_irq_event_percpu+0x35/0x90
[   29.368247]  handle_irq_event+0x39/0x60
[   29.368632]  handle_fasteoi_irq+0xc2/0x1d0
[   29.368950]  __common_interrupt+0x7f/0x150
[   29.369254]  common_interrupt+0xb4/0xd0
[   29.369547]  </IRQ>
[   29.369708]  asm_common_interrupt+0x1e/0x40
[   29.370016] RIP: 0010:native_safe_halt+0x17/0x20
[   29.370360] Code: 07 0f 00 2d db 80 43 00 f4 5d c3 0f 1f 84 00 00 00
00 00 8b 05 c2 37 e5 01 55 48 89 e5 85 c0 7e 07 0f 00 2d bb 80 43 00 fb
f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d f9 91
[   29.371696] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246
[   29.372079] RAX: 0000000000000000 RBX: 0000000000000002
RCX: 0000000000000000
[   29.372595] RDX: 0000000000000000 RSI: ffffffff854f67a4
RDI: ffffffff85403406
[   29.373122] RBP: ffffc9000008fe90 R08: 0000000000000001
R09: 0000000000000001
[   29.373646] R10: 0000000000000000 R11: 0000000000000001
R12: ffffffff86009188
[   29.374160] R13: 0000000000000000 R14: 0000000000000000
R15: ffff888100258000
[   29.374690]  default_idle+0x9/0x10
[   29.374944]  arch_cpu_idle+0xa/0x10
[   29.375198]  default_idle_call+0x6e/0x250
[   29.375491]  do_idle+0x1f0/0x2d0
[   29.375740]  cpu_startup_entry+0x18/0x20
[   29.376034]  start_secondary+0x11f/0x160
[   29.376328]  secondary_startup_64_no_verify+0xb0/0xbb
[   29.376705] Modules linked in:
[   29.376939] Dumping ftrace buffer:
[   29.377187]    (ftrace buffer empty)
[   29.377460] CR2: 0000000000000014
[   29.377712] ---[ end trace 51a473dffb618c47 ]---
[   29.378056] RIP: 0010:via_sdc_isr+0x21f/0x410
[   29.378380] Code: ff ff e8 84 aa d0 fd 66 45 89 7e 28 66 41 f7 c4 00
10 75 56 e8 72 aa d0 fd 66 41 f7 c4 00 c0 74 10 e8 65 aa d0 fd 48 8b 43
18 <c7> 40 14 ac ff ff ff e8 55 aa d0 fd 48 89 df e8 ad fb ff ff e9 77
[   29.379714] RSP: 0018:ffffc90000118e98 EFLAGS: 00010046
[   29.380098] RAX: 0000000000000000 RBX: ffff888107d77880
RCX: 0000000000000000
[   29.380614] RDX: 0000000000000000 RSI: ffffffff835d20bb
RDI: 00000000ffffffff
[   29.381134] RBP: ffffc90000118ed8 R08: 0000000000000001
R09: 0000000000000001
[   29.381653] R10: 0000000000000000 R11: 0000000000000001
R12: 0000000000008600
[   29.382176] R13: ffff888107d779c8 R14: ffffc90009c00200
R15: 0000000000008000
[   29.382697] FS:  0000000000000000(0000) GS:ffff88817bc80000(0000)
knlGS:0000000000000000
[   29.383277] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   29.383697] CR2: 0000000000000014 CR3: 0000000005a2e000
CR4: 00000000000006e0
[   29.384223] DR0: 0000000000000000 DR1: 0000000000000000
DR2: 0000000000000000
[   29.384736] DR3: 0000000000000000 DR6: 00000000fffe0ff0
DR7: 0000000000000400
[   29.385260] Kernel panic - not syncing: Fatal exception in interrupt
[   29.385882] Dumping ftrace buffer:
[   29.386135]    (ftrace buffer empty)
[   29.386401] Kernel Offset: disabled
[   29.386656] Rebooting in 1 seconds..
---
 drivers/mmc/host/via-sdmmc.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/mmc/host/via-sdmmc.c +3 -0
index 9fdb92729c28..1b66466d2ed4 100644
@@ -865,6 +865,9 @@ static void via_sdc_data_isr(struct via_crdr_mmc_host *host, u16 intmask)
 {
 	BUG_ON(intmask == 0);
 
+	if (!host->data)
+		return;
+
 	if (intmask & VIA_CRDR_SDSTS_DT)
 		host->data->error = -ETIMEDOUT;
 	else if (intmask & (VIA_CRDR_SDSTS_RC | VIA_CRDR_SDSTS_WC))
Signature · 1 line
2.30.2
author maintainer
#21 lore raw

PATCH 22/31 crypto: shash - avoid comparing pointers to exported functions under CFI

In reply to Sasha Levin

From: Ard Biesheuvel <[email protected]>

[ Upstream commit 22ca9f4aaf431a9413dcc115dd590123307f274f ]

crypto_shash_alg_has_setkey() is implemented by testing whether the .setkey() member of a struct shash_alg points to the default version, called shash_no_setkey(). As crypto_shash_alg_has_setkey() is a static inline, this requires shash_no_setkey() to be exported to modules.

Unfortunately, when building with CFI, function pointers are routed via CFI stubs which are private to each module (or to the kernel proper) and so this function pointer comparison may fail spuriously.

Let's fix this by turning crypto_shash_alg_has_setkey() into an out of line function.

---
 crypto/shash.c                 | 18 +++++++++++++++---
 include/crypto/internal/hash.h |  8 +-------
 2 files changed, 16 insertions(+), 10 deletions(-)
crypto/shash.c +15 -3
index a04145e5306a..55e7a2f63b34 100644
@@ -25,12 +25,24 @@
 
 static const struct crypto_type crypto_shash_type;
 
-int shash_no_setkey(struct crypto_shash *tfm, const u8 *key,
-		    unsigned int keylen)
+static int shash_no_setkey(struct crypto_shash *tfm, const u8 *key,
+			   unsigned int keylen)
 {
 	return -ENOSYS;
 }
-EXPORT_SYMBOL_GPL(shash_no_setkey);
+
+/*
+ * Check whether an shash algorithm has a setkey function.
+ *
+ * For CFI compatibility, this must not be an inline function.  This is because
+ * when CFI is enabled, modules won't get the same address for shash_no_setkey
+ * (if it were exported, which inlining would require) as the core kernel will.
+ */
+bool crypto_shash_alg_has_setkey(struct shash_alg *alg)
+{
+	return alg->setkey != shash_no_setkey;
+}
+EXPORT_SYMBOL_GPL(crypto_shash_alg_has_setkey);
 
 static int shash_setkey_unaligned(struct crypto_shash *tfm, const u8 *key,
 				  unsigned int keylen)
include/crypto/internal/hash.h +1 -7
index a0b0ad9d585e..64283c22f1ee 100644
@@ -82,13 +82,7 @@ int ahash_register_instance(struct crypto_template *tmpl,
 			    struct ahash_instance *inst);
 void ahash_free_instance(struct crypto_instance *inst);
 
-int shash_no_setkey(struct crypto_shash *tfm, const u8 *key,
-		    unsigned int keylen);
-
-static inline bool crypto_shash_alg_has_setkey(struct shash_alg *alg)
-{
-	return alg->setkey != shash_no_setkey;
-}
+bool crypto_shash_alg_has_setkey(struct shash_alg *alg);
 
 bool crypto_hash_alg_has_setkey(struct hash_alg_common *halg);
 
Signature · 1 line
2.30.2
author maintainer
#22 lore raw

PATCH 23/31 media: dvb_net: avoid speculation from net slot

In reply to Sasha Levin

From: Mauro Carvalho Chehab <[email protected]>

[ Upstream commit abc0226df64dc137b48b911c1fe4319aec5891bb ]

The risk of especulation is actually almost-non-existing here, as there are very few users of TCP/IP using the DVB stack, as, this is mainly used with DVB-S/S2 cards, and only by people that receives TCP/IP from satellite connections, which limits a lot the number of users of such feature(*).

(*) In thesis, DVB-C cards could also benefit from it, but I'm yet to see a hardware that supports it.

Yet, fixing it is trivial.

---
 drivers/media/dvb-core/dvb_net.c | 25 +++++++++++++++++++------
 1 file changed, 19 insertions(+), 6 deletions(-)
drivers/media/dvb-core/dvb_net.c +19 -6
index 10f78109bb3f..3f154755bbc6 100644
@@ -56,6 +56,7 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/netdevice.h>
+#include <linux/nospec.h>
 #include <linux/etherdevice.h>
 #include <linux/dvb/net.h>
 #include <linux/uio.h>
@@ -1473,14 +1474,20 @@ static int dvb_net_do_ioctl(struct file *file,
 		struct net_device *netdev;
 		struct dvb_net_priv *priv_data;
 		struct dvb_net_if *dvbnetif = parg;
+		int if_num = dvbnetif->if_num;
 
-		if (dvbnetif->if_num >= DVB_NET_DEVICES_MAX ||
-		    !dvbnet->state[dvbnetif->if_num]) {
+		if (if_num >= DVB_NET_DEVICES_MAX) {
 			ret = -EINVAL;
 			goto ioctl_error;
 		}
+		if_num = array_index_nospec(if_num, DVB_NET_DEVICES_MAX);
 
-		netdev = dvbnet->device[dvbnetif->if_num];
+		if (!dvbnet->state[if_num]) {
+			ret = -EINVAL;
+			goto ioctl_error;
+		}
+
+		netdev = dvbnet->device[if_num];
 
 		priv_data = netdev_priv(netdev);
 		dvbnetif->pid=priv_data->pid;
@@ -1533,14 +1540,20 @@ static int dvb_net_do_ioctl(struct file *file,
 		struct net_device *netdev;
 		struct dvb_net_priv *priv_data;
 		struct __dvb_net_if_old *dvbnetif = parg;
+		int if_num = dvbnetif->if_num;
+
+		if (if_num >= DVB_NET_DEVICES_MAX) {
+			ret = -EINVAL;
+			goto ioctl_error;
+		}
+		if_num = array_index_nospec(if_num, DVB_NET_DEVICES_MAX);
 
-		if (dvbnetif->if_num >= DVB_NET_DEVICES_MAX ||
-		    !dvbnet->state[dvbnetif->if_num]) {
+		if (!dvbnet->state[if_num]) {
 			ret = -EINVAL;
 			goto ioctl_error;
 		}
 
-		netdev = dvbnet->device[dvbnetif->if_num];
+		netdev = dvbnet->device[if_num];
 
 		priv_data = netdev_priv(netdev);
 		dvbnetif->pid=priv_data->pid;
Signature · 1 line
2.30.2
author maintainer
#23 lore raw

PATCH 24/31 media: siano: fix device register error path

In reply to Sasha Levin

From: Mauro Carvalho Chehab <[email protected]>

[ Upstream commit 5368b1ee2939961a16e74972b69088433fc52195 ]

As reported by smatch:

	drivers/media/common/siano/smsdvb-main.c:1231 smsdvb_hotplug() warn: '&client->entry' not removed from list

If an error occur at the end of the registration logic, it won't drop the device from the list.

---
 drivers/media/common/siano/smsdvb-main.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/media/common/siano/smsdvb-main.c +4 -0
index afca47b97c2a..637ace7a2b5c 100644
@@ -1187,6 +1187,10 @@ static int smsdvb_hotplug(struct smscore_device_t *coredev,
 	return 0;
 
 media_graph_error:
+	mutex_lock(&g_smsdvb_clientslock);
+	list_del(&client->entry);
+	mutex_unlock(&g_smsdvb_clientslock);
+
 	smsdvb_debugfs_release(client);
 
 client_error:
Signature · 1 line
2.30.2
author maintainer
#24 lore raw

PATCH 25/31 media: imx-csi: Skip first few frames from a BT.656 source

In reply to Sasha Levin

From: Steve Longerbeam <[email protected]>

[ Upstream commit e198be37e52551bb863d07d2edc535d0932a3c4f ]

Some BT.656 sensors (e.g. ADV718x) transmit frames with unstable BT.656 sync codes after initial power on. This confuses the imx CSI,resulting in vertical and/or horizontal sync issues. Skip the first 20 frames to avoid the unstable sync codes.

[fabio: fixed checkpatch warning and increased the frame skipping to 20]

---
 drivers/staging/media/imx/imx-media-csi.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)
drivers/staging/media/imx/imx-media-csi.c +13 -1
index 0f8fdc347091..c7df0ffb3510 100644
@@ -730,9 +730,10 @@ static int csi_setup(struct csi_priv *priv)
 
 static int csi_start(struct csi_priv *priv)
 {
-	struct v4l2_fract *output_fi;
+	struct v4l2_fract *input_fi, *output_fi;
 	int ret;
 
+	input_fi = &priv->frame_interval[CSI_SINK_PAD];
 	output_fi = &priv->frame_interval[priv->active_output_pad];
 
 	/* start upstream */
@@ -741,6 +742,17 @@ static int csi_start(struct csi_priv *priv)
 	if (ret)
 		return ret;
 
+	/* Skip first few frames from a BT.656 source */
+	if (priv->upstream_ep.bus_type == V4L2_MBUS_BT656) {
+		u32 delay_usec, bad_frames = 20;
+
+		delay_usec = DIV_ROUND_UP_ULL((u64)USEC_PER_SEC *
+			input_fi->numerator * bad_frames,
+			input_fi->denominator);
+
+		usleep_range(delay_usec, delay_usec + 1000);
+	}
+
 	if (priv->dest == IPU_CSI_DEST_IDMAC) {
 		ret = csi_idmac_start(priv);
 		if (ret)
Signature · 1 line
2.30.2
author maintainer
#25 lore raw

PATCH 26/31 btrfs: fix error handling in __btrfs_update_delayed_inode

In reply to Sasha Levin

From: Josef Bacik <[email protected]>

[ Upstream commit bb385bedded3ccbd794559600de4a09448810f4a ]

If we get an error while looking up the inode item we'll simply bail without cleaning up the delayed node. This results in this style of warning happening on commit:

  WARNING: CPU: 0 PID: 76403 at fs/btrfs/delayed-inode.c:1365 btrfs_assert_delayed_root_empty+0x5b/0x90
  CPU: 0 PID: 76403 Comm: fsstress Tainted: G        W         5.13.0-rc1+ #373
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
  RIP: 0010:btrfs_assert_delayed_root_empty+0x5b/0x90
  RSP: 0018:ffffb8bb815a7e50 EFLAGS: 00010286
  RAX: 0000000000000000 RBX: ffff95d6d07e1888 RCX: ffff95d6c0fa3000
  RDX: 0000000000000002 RSI: 000000000029e91c RDI: ffff95d6c0fc8060
  RBP: ffff95d6c0fc8060 R08: 00008d6d701a2c1d R09: 0000000000000000
  R10: ffff95d6d1760ea0 R11: 0000000000000001 R12: ffff95d6c15a4d00
  R13: ffff95d6c0fa3000 R14: 0000000000000000 R15: ffffb8bb815a7e90
  FS:  00007f490e8dbb80(0000) GS:ffff95d73bc00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007f6e75555cb0 CR3: 00000001101ce001 CR4: 0000000000370ef0
  Call Trace:
   btrfs_commit_transaction+0x43c/0xb00
   ? finish_wait+0x80/0x80
   ? vfs_fsync_range+0x90/0x90
   iterate_supers+0x8c/0x100
   ksys_sync+0x50/0x90
   __do_sys_sync+0xa/0x10
   do_syscall_64+0x3d/0x80
   entry_SYSCALL_64_after_hwframe+0x44/0xae

Because the iref isn't dropped and this leaves an elevated node->count, so any release just re-queues it onto the delayed inodes list. Fix this by going to the out label to handle the proper cleanup of the delayed node.

---
 fs/btrfs/delayed-inode.c | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)
fs/btrfs/delayed-inode.c +4 -6
index fea5ccfade5c..f3994ee1a6e6 100644
@@ -1030,12 +1030,10 @@ static int __btrfs_update_delayed_inode(struct btrfs_trans_handle *trans,
 	nofs_flag = memalloc_nofs_save();
 	ret = btrfs_lookup_inode(trans, root, path, &key, mod);
 	memalloc_nofs_restore(nofs_flag);
-	if (ret > 0) {
-		btrfs_release_path(path);
-		return -ENOENT;
-	} else if (ret < 0) {
-		return ret;
-	}
+	if (ret > 0)
+		ret = -ENOENT;
+	if (ret < 0)
+		goto out;
 
 	leaf = path->nodes[0];
 	inode_item = btrfs_item_ptr(leaf, path->slots[0],
Signature · 1 line
2.30.2
author maintainer
#26 lore raw

PATCH 27/31 btrfs: abort transaction if we fail to update the delayed inode

In reply to Sasha Levin

From: Josef Bacik <[email protected]>

[ Upstream commit 04587ad9bef6ce9d510325b4ba9852b6129eebdb ]

If we fail to update the delayed inode we need to abort the transaction, because we could leave an inode with the improper counts or some other such corruption behind.

---
 fs/btrfs/delayed-inode.c | 8 ++++++++
 1 file changed, 8 insertions(+)
fs/btrfs/delayed-inode.c +8 -0
index f3994ee1a6e6..1fbe2dee1e70 100644
@@ -1071,6 +1071,14 @@ static int __btrfs_update_delayed_inode(struct btrfs_trans_handle *trans,
 	btrfs_delayed_inode_release_metadata(fs_info, node, (ret < 0));
 	btrfs_release_delayed_inode(node);
 
+	/*
+	 * If we fail to update the delayed inode we need to abort the
+	 * transaction, because we could leave the inode with the improper
+	 * counts behind.
+	 */
+	if (ret && ret != -ENOENT)
+		btrfs_abort_transaction(trans, ret);
+
 	return ret;
 
 search:
Signature · 1 line
2.30.2
author maintainer
#27 lore raw

PATCH 28/31 btrfs: make Private2 lifespan more consistent

In reply to Sasha Levin

From: Qu Wenruo <[email protected]>

[ Upstream commit 87b4d86baae219a9a79f6b0a1434b2a42fd40d09 ]

Currently we use page Private2 bit to indicate that we have ordered extent for the page range.

But the lifespan of it is not consistent, during regular writeback path, there are two locations to clear the same PagePrivate2:

T ----- Page marked Dirty
|
+ ----- Page marked Private2, through btrfs_run_dealloc_range() |
+ ----- Page cleared Private2, through btrfs_writepage_cow_fixup()
| in __extent_writepage_io()
| ^^^ Private2 cleared for the first time
|
+ ----- Page marked Writeback, through btrfs_set_range_writeback()
| in __extent_writepage_io().
|
+ ----- Page cleared Private2, through
| btrfs_writepage_endio_finish_ordered()
| ^^^ Private2 cleared for the second time.
|
+ ----- Page cleared Writeback, through btrfs_writepage_endio_finish_ordered()

Currently PagePrivate2 is mostly to prevent ordered extent accounting being executed for both endio and invalidatepage.
Thus only the one who cleared page Private2 is responsible for ordered extent accounting.

But the fact is, in btrfs_writepage_endio_finish_ordered(), page Private2 is cleared and ordered extent accounting is executed unconditionally.

The race prevention only happens through btrfs_invalidatepage(), where we wait for the page writeback first, before checking the Private2 bit.

This means, Private2 is also protected by Writeback bit, and there is no need for btrfs_writepage_cow_fixup() to clear Priavte2.

This patch will change btrfs_writepage_cow_fixup() to just check PagePrivate2, not to clear it.
The clearing will happen in either btrfs_invalidatepage() or btrfs_writepage_endio_finish_ordered().

This makes the Private2 bit easier to understand, just meaning the page has unfinished ordered extent attached to it.

And this patch is a hard requirement for the incoming refactoring for how we finished ordered IO for endio context, as the coming patch will check Private2 to determine if we need to do the ordered extent accounting. Thus this patch is definitely needed or we will hang due to unfinished ordered extent.

---
 fs/btrfs/inode.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/btrfs/inode.c +1 -1
index bf0e0e3e09c5..acf91542b477 100644
@@ -2223,7 +2223,7 @@ static int btrfs_writepage_start_hook(struct page *page, u64 start, u64 end)
 	struct btrfs_writepage_fixup *fixup;
 
 	/* this page is properly in the ordered list */
-	if (TestClearPagePrivate2(page))
+	if (PagePrivate2(page))
 		return 0;
 
 	if (PageChecked(page))
Signature · 1 line
2.30.2
author maintainer
#28 lore raw

PATCH 29/31 btrfs: fix the filemap_range_has_page() call in btrfs_punch_hole_lock_range()

In reply to Sasha Levin

From: Qu Wenruo <[email protected]>

[ Upstream commit 0528476b6ac7832f31e2ed740a57ae31316b124e ]

[BUG]
With current subpage RW support, the following script can hang the fs with 64K page size.

 # mkfs.btrfs -f -s 4k $dev
 # mount $dev -o nospace_cache $mnt
 # fsstress -w -n 50 -p 1 -s 1607749395 -d $mnt

The kernel will do an infinite loop in btrfs_punch_hole_lock_range().

[CAUSE]
In btrfs_punch_hole_lock_range() we:

- Truncate page cache range
- Lock extent io tree
- Wait any ordered extents in the range.

We exit the loop until we meet all the following conditions:

- No ordered extent in the lock range
- No page is in the lock range

The latter condition has a pitfall, it only works for sector size == PAGE_SIZE case.

While can't handle the following subpage case:

  0       32K     64K     96K     128K
  |       |///////||//////|       ||

lockstart=32K
lockend=96K - 1

In this case, although the range crosses 2 pages, truncate_pagecache_range() will invalidate no page at all, but only zero the [32K, 96K) range of the two pages.

Thus filemap_range_has_page(32K, 96K-1) will always return true, thus we will never meet the loop exit condition.

[FIX]
Fix the problem by doing page alignment for the lock range.

Function filemap_range_has_page() has already handled lend < lstart case, we only need to round up @lockstart, and round_down @lockend for truncate_pagecache_range().

This modification should not change any thing for sector size == PAGE_SIZE case, as in that case our range is already page aligned.

---
 fs/btrfs/file.c | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)
fs/btrfs/file.c +12 -1
index 41ad37f8062a..cfbe2961bd1d 100644
@@ -2444,6 +2444,17 @@ static int btrfs_punch_hole_lock_range(struct inode *inode,
 				       const u64 lockend,
 				       struct extent_state **cached_state)
 {
+	/*
+	 * For subpage case, if the range is not at page boundary, we could
+	 * have pages at the leading/tailing part of the range.
+	 * This could lead to dead loop since filemap_range_has_page()
+	 * will always return true.
+	 * So here we need to do extra page alignment for
+	 * filemap_range_has_page().
+	 */
+	const u64 page_lockstart = round_up(lockstart, PAGE_SIZE);
+	const u64 page_lockend = round_down(lockend + 1, PAGE_SIZE) - 1;
+
 	while (1) {
 		struct btrfs_ordered_extent *ordered;
 		int ret;
@@ -2463,7 +2474,7 @@ static int btrfs_punch_hole_lock_range(struct inode *inode,
 		    (ordered->file_offset + ordered->len <= lockstart ||
 		     ordered->file_offset > lockend)) &&
 		     !filemap_range_has_page(inode->i_mapping,
-					     lockstart, lockend)) {
+					     page_lockstart, page_lockend)) {
 			if (ordered)
 				btrfs_put_ordered_extent(ordered);
 			break;
Signature · 1 line
2.30.2
author maintainer
#29 lore raw

PATCH 30/31 btrfs: disable build on platforms having page size 256K

In reply to Sasha Levin

From: Christophe Leroy <[email protected]>

[ Upstream commit b05fbcc36be1f8597a1febef4892053a0b2f3f60 ]

With a config having PAGE_SIZE set to 256K, BTRFS build fails with the following message

include/linux/compiler_types.h:326:38: error: call to '__compiletime_assert_791' declared with attribute error:
BUILD_BUG_ON failed: (BTRFS_MAX_COMPRESSED % PAGE_SIZE) != 0

BTRFS_MAX_COMPRESSED being 128K, BTRFS cannot support platforms with 256K pages at the time being.

There are two platforms that can select 256K pages:
- hexagon
- powerpc

Disable BTRFS when 256K page size is selected. Supporting this would require changes to the subpage mode that's currently being developed. Given that 256K is many times larger than page sizes commonly used and for what the algorithms and structures have been tuned, it's out of scope and disabling build is a reasonable option.

---
 fs/btrfs/Kconfig | 2 ++
 1 file changed, 2 insertions(+)
fs/btrfs/Kconfig +2 -0
index 23537bc8c827..7233127bb93a 100644
@@ -12,6 +12,8 @@ config BTRFS_FS
 	select RAID6_PQ
 	select XOR_BLOCKS
 	select SRCU
+	depends on !PPC_256K_PAGES	# powerpc
+	depends on !PAGE_SIZE_256KB	# hexagon
 
 	help
 	  Btrfs is a general purpose copy-on-write filesystem with extents,
Signature · 1 line
2.30.2
author maintainer
#30 lore raw

PATCH 31/31 regulator: da9052: Ensure enough delay time for .set_voltage_time_sel

In reply to Sasha Levin

From: Axel Lin <[email protected]>

[ Upstream commit a336dc8f683e5be794186b5643cd34cb28dd2c53 ]

Use DIV_ROUND_UP to prevent truncation by integer division issue. This ensures we return enough delay time.

Also fix returning negative value when new_sel < old_sel.

---
 drivers/regulator/da9052-regulator.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/regulator/da9052-regulator.c +2 -1
index 9ececfef42d6..bd91c95f73e0 100644
@@ -258,7 +258,8 @@ static int da9052_regulator_set_voltage_time_sel(struct regulator_dev *rdev,
 	case DA9052_ID_BUCK3:
 	case DA9052_ID_LDO2:
 	case DA9052_ID_LDO3:
-		ret = (new_sel - old_sel) * info->step_uV / 6250;
+		ret = DIV_ROUND_UP(abs(new_sel - old_sel) * info->step_uV,
+				   6250);
 		break;
 	}
 
Signature · 1 line
2.30.2