sunxi: H616: SPI boot support
Subsystems (3)
cover sunxi: H616: SPI boot support
The Allwinner H616 supports booting from SPI NOR flash, for which we use our SPL specific SPI driver. Since this uses hardcoded values for clocks, resets and pins, we need to extend it to cover the H616 SoC as well.
Patch 1/3 extends the logic that determines the offset of the U-Boot payload, from a fixed value to actually observing the SPL size. Patch 2/3 piggy backs on the existing H6 SPI boot support, to cover the (very similar) H616 as well. The only actual difference between the two is one pin configuration.
Patch 3/3 enables SPI boot for the OrangePi Zero 2 board, which comes with a 2MiB SPI flash chip soldered.
In my experiments I couldn't actually convince the BROM to load the SPL, it always fell through to FEL mode. I post this series anyway, because:
1) We will need this code in any case, since it loads the rest of U-Boot (and TF-A) from SPI flash. By hacking sunxi-fel I could verify that this part works: the SPL code detected "SPI boot" and booted the rest of the firmware successfully from SPI flash.
2) I would encourage other people to try this, maybe it's just my board that is broken? (I dimly remember booting something some months ago.) The easiest way to flash U-Boot is via sunxi-fel:
$ sunxi-fel -v -p spiflash-write 0 u-boot-sunxi-with-spl.bin
Cheers,
Andre
Andre Przywara (3):
sunxi: SPL SPI: Allow larger SPL
sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC
sunxi: OrangePi Zero 2: Enable SPI booting
arch/arm/mach-sunxi/Kconfig | 2 +- arch/arm/mach-sunxi/spl_spi_sunxi.c | 37 +++++++++++++++++------------ configs/orangepi_zero2_defconfig | 1 + 3 files changed, 24 insertions(+), 16 deletions(-)
Signature · 1 line
2.17.5
PATCH 1/3 sunxi: SPL SPI: Allow larger SPL
The more recent Allwinner SoCs BootROMs can actually load SPL images larger than 32KB. We use this on the H616 to fit the extra code needed for the PMIC into the image, and have provisions in board.c to respect that larger SPL size when booting from MMC.
However the sunxi SPL SPI loader has a hardcoded load offset of 32KB, which will fail on the H616.
To fix this, use the same algorithm we use for MMC: if the SPL size is smaller than 32KB, we use 32KB, otherwise we expect the U-Boot payload directly after the SPL code.
This prepares for SPI booting with larger SPLs like on the H616.
--- arch/arm/mach-sunxi/spl_spi_sunxi.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)
arch/arm/mach-sunxi/spl_spi_sunxi.c +7 -3
@@ -7,6 +7,7 @@#include <image.h> #include <log.h> #include <spl.h> +#include <asm/arch/spl.h> #include <asm/gpio.h> #include <asm/io.h> #include <linux/bitops.h>
@@ -326,10 +327,13 @@ static int spl_spi_load_image(struct spl_image_info *spl_image,int ret =0 ;struct image_header *header; header = (struct image_header *)(CONFIG_SYS_TEXT_BASE ); +int load_offset =readl (SPL_ADDR +0x10 ); + + load_offset =max (load_offset,CONFIG_SYS_SPI_U_BOOT_OFFS );spi0_init (); -spi0_read_data ((void *)header,CONFIG_SYS_SPI_U_BOOT_OFFS ,0x40 ); +spi0_read_data ((void *)header, load_offset,0x40 );if (IS_ENABLED (CONFIG_SPL_LOAD_FIT ) &&image_get_magic (header) ==FDT_MAGIC ) {
@@ -342,14 +346,14 @@ static int spl_spi_load_image(struct spl_image_info *spl_image, load.bl_len =1 ; load.read = spi_load_read; ret =spl_load_simple_fit (spl_image, &load, -CONFIG_SYS_SPI_U_BOOT_OFFS , header); + load_offset, header); }else { ret =spl_parse_image_header (spl_image, header);if (ret)return ret;spi0_read_data ((void *)spl_image->load_addr, -CONFIG_SYS_SPI_U_BOOT_OFFS , spl_image->size); + load_offset, spl_image->size); }spi0_deinit ();
Signature · 1 line
2.17.5
Re: [PATCH 1/3] sunxi: SPL SPI: Allow larger SPL
Quoted 9 lines · Andre Przywara
The more recent Allwinner SoCs BootROMs can actually load SPL images larger than 32KB. We use this on the H616 to fit the extra code needed for the PMIC into the image, and have provisions in
board.cto respect that larger SPL size when booting from MMC.However the sunxi SPL SPI loader has a hardcoded load offset of 32KB, which will fail on the H616.
Quoted 8 lines
To fix this, use the same algorithm we use for MMC: if the SPL size is smaller than 32KB, we use 32KB, otherwise we expect the U-Boot payload directly after the SPL code.
This prepares for SPI booting with larger SPLs like on the H616.
Signed-off-by Andre Przywara <[email protected]>---
PATCH 2/3 sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC
In reply to Andre PrzywaraThe H616 SoC uses the same SPI IP as the H6, also shares the same clocks and reset bits.
The only real difference is a slight change in the pin assignment: the H6 uses PC5, the H616 PC4 instead. This makes for a small change in our spi0_pinmux_setup() routine.
Apart from that, just extend the H6 #ifdef guards to also cover the H616, using the shared CONFIG_SUN50I_GEN_H6 symbol.
Also use this symbol for the Kconfig dependency.
--- arch/arm/mach-sunxi/Kconfig | 2 +- arch/arm/mach-sunxi/spl_spi_sunxi.c | 27 +++++++++++++++------------ 2 files changed, 16 insertions(+), 13 deletions(-)
arch/arm/mach-sunxi/Kconfig +1 -1
@@ -1057,7 +1057,7 @@ config SPL_STACK_R_ADDR config SPL_SPI_SUNXI bool "Support for SPI Flash on Allwinner SoCs in SPL" - depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_R40 || MACH_SUN50I_H6 + depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_R40 || SUN50I_GEN_H6 help Enable support for SPI Flash. This option allows SPL to read from sunxi SPI Flash. It uses the same method as the boot ROM, so does
arch/arm/mach-sunxi/spl_spi_sunxi.c +15 -12
@@ -78,7 +78,7 @@#define CCM_AHB_GATING0 (0x01C20000 + 0x60)#define CCM_H6_SPI_BGR_REG (0x03001000 + 0x96c) -#ifdef CONFIG_MACH_SUN50I_H6 +#ifdef CONFIG_SUN50I_GEN_H6 #define CCM_SPI0_CLK (0x03001000 + 0x940)#else #define CCM_SPI0_CLK (0x01C20000 + 0xA0)
@@ -96,7 +96,7 @@/* * Allwinner A10/A20 SoCs were using pins PC0,PC1,PC2,PC23 for booting * from SPI Flash, everything else is using pins PC0,PC1,PC2,PC3. -* The H6 uses PC0, PC2, PC3, PC5. +* The H6 uses PC0, PC2, PC3, PC5, the H616 PC0, PC2, PC3, PC4. */ static void spi0_pinmux_setup (unsigned int pin_function) {
@@ -104,11 +104,14 @@ static void spi0_pinmux_setup(unsigned int pin_function)sunxi_gpio_set_cfgpin (SUNXI_GPC (0 ), pin_function);sunxi_gpio_set_cfgpin (SUNXI_GPC (2 ), pin_function); -/* All chips except H6 use PC1, and only H6 uses PC5. */ -if (!IS_ENABLED (CONFIG_MACH_SUN50I_H6 )) +/* All chips except H6 and H616 use PC1. */ +if (!IS_ENABLED (CONFIG_SUN50I_GEN_H6 ))sunxi_gpio_set_cfgpin (SUNXI_GPC (1 ), pin_function); -else + +if (IS_ENABLED (CONFIG_MACH_SUN50I_H6 ))sunxi_gpio_set_cfgpin (SUNXI_GPC (5 ), pin_function); +if (IS_ENABLED (CONFIG_MACH_SUN50I_H616 )) +sunxi_gpio_set_cfgpin (SUNXI_GPC (4 ), pin_function);/* Older generations use PC23 for CS, newer ones use PC3. */ if (IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN7I) ||
@@ -121,7 +124,7 @@ static void spi0_pinmux_setup(unsigned int pin_function)static bool is_sun6i_gen_spi (void ) {return IS_ENABLED (CONFIG_SUNXI_GEN_SUN6I ) || -IS_ENABLED (CONFIG_MACH_SUN50I_H6 ); +IS_ENABLED (CONFIG_SUN50I_GEN_H6 ); }static uintptr_t spi0_base_address (void )
@@ -129,7 +132,7 @@ static uintptr_t spi0_base_address(void)if (IS_ENABLED (CONFIG_MACH_SUN8I_R40 ))return 0x01C05000 ; -if (IS_ENABLED (CONFIG_MACH_SUN50I_H6 )) +if (IS_ENABLED (CONFIG_SUN50I_GEN_H6 ))return 0x05010000 ;if (!is_sun6i_gen_spi ())
@@ -146,14 +149,14 @@ static void spi0_enable_clock(void)uintptr_t base =spi0_base_address ();/* Deassert SPI0 reset on SUN6I */ -if (IS_ENABLED (CONFIG_MACH_SUN50I_H6 )) +if (IS_ENABLED (CONFIG_SUN50I_GEN_H6 ))setbits_le32 (CCM_H6_SPI_BGR_REG , (1U <<16 ) |0x1 );else if (is_sun6i_gen_spi ())setbits_le32 (SUN6I_BUS_SOFT_RST_REG0 , (1 <<AHB_RESET_SPI0_SHIFT ));/* Open the SPI0 gate */ -if (!IS_ENABLED (CONFIG_MACH_SUN50I_H6 )) +if (!IS_ENABLED (CONFIG_SUN50I_GEN_H6 ))setbits_le32 (CCM_AHB_GATING0 , (1 <<AHB_GATE_OFFSET_SPI0 ));/* Divide by 4 */
@@ -194,11 +197,11 @@ static void spi0_disable_clock(void)writel (0 ,CCM_SPI0_CLK );/* Close the SPI0 gate */ -if (!IS_ENABLED (CONFIG_MACH_SUN50I_H6 )) +if (!IS_ENABLED (CONFIG_SUN50I_GEN_H6 ))clrbits_le32 (CCM_AHB_GATING0 , (1 <<AHB_GATE_OFFSET_SPI0 ));/* Assert SPI0 reset on SUN6I */ -if (IS_ENABLED (CONFIG_MACH_SUN50I_H6 )) +if (IS_ENABLED (CONFIG_SUN50I_GEN_H6 ))clrbits_le32 (CCM_H6_SPI_BGR_REG , (1U <<16 ) |0x1 );else if (is_sun6i_gen_spi ()) clrbits_le32(SUN6I_BUS_SOFT_RST_REG0,
@@ -210,7 +213,7 @@ static void spi0_init(void)unsigned int pin_function =SUNXI_GPC_SPI0 ;if (IS_ENABLED (CONFIG_MACH_SUN50I ) || -IS_ENABLED (CONFIG_MACH_SUN50I_H6 )) +IS_ENABLED (CONFIG_SUN50I_GEN_H6 )) pin_function =SUN50I_GPC_SPI0 ;spi0_pinmux_setup (pin_function);
Signature · 1 line
2.17.5
Re: [PATCH 2/3] sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC
Quoted 7 lines · Andre Przywara
The H616 SoC uses the same SPI IP as the H6, also shares the same clocks and reset bits.
The only real difference is a slight change in the pin assignment: the H6 uses PC5, the H616 PC4 instead. This makes for a small change in ourspi0_pinmux_setup()routine.
Quoted 6 lines
Apart from that, just extend the H6 #ifdef guards to also cover the H616, using the shared
CONFIG_SUN50I_GEN_H6symbol.
Also use this symbol for theKconfigdependency.Signed-off-by Andre Przywara <[email protected]>---
PATCH 3/3 sunxi: OrangePi Zero 2: Enable SPI booting
In reply to Andre PrzywaraThe OrangePi Zero 2 board comes with 2MB of SPI flash, from which the BROM is supposed to be able to boot from.
Enable the SPL code responsible for finding and loading U-Boot proper and friends, so that u-boot-sunxi-with-spl.bin can be written into the flash.
--- configs/orangepi_zero2_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/orangepi_zero2_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_DRAM_SUN50I_H616_WRITE_TRAINING=y CONFIG_MACH_SUN50I_H616=y CONFIG_MMC0_CD_PIN="PF6" CONFIG_R_I2C_ENABLE=y +CONFIG_SPL_SPI_SUNXI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_I2C_SUPPORT=y CONFIG_PHY_REALTEK=y
Signature · 1 line
2.17.5
Re: [PATCH 3/3] sunxi: OrangePi Zero 2: Enable SPI booting
Quoted 9 lines · Andre Przywara
The OrangePi Zero 2 board comes with 2MB of SPI flash, from which the BROM is supposed to be able to boot from.
Enable the SPL code responsible for finding and loading U-Boot proper and friends, so that u-boot-sunxi-with-spl.bin can be written into the flash.
Signed-off-by Andre Przywara <[email protected]>---