Skip to contentSkip to conversation

PCI: Add support for J7200 and AM64

PATCH Superseded Kishon Vijay Abraham I 2 participants 7 messages Jul 6, 2021 – Jul 7, 2021

Subsystems (6)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

cover PCI: Add support for J7200 and AM64

This series adds the compatible specific to J7200 and AM64 and applies the erratas and configuration specific to them.

This series also includes Nadeem's patch that adds a quirk in Cadence driver which is used by J7200 [1].

The DT binding for both J7200 and AM64 is already merged.

[1] -> https://lore.kernel.org/r/[email protected]

Kishon Vijay Abraham I (4):
PCI: j721e: Add PCIe support for J7200
PCI: j721e: Add PCIe support for AM64
misc: pci_endpoint_test: Do not request or allocate IRQs in probe
misc: pci_endpoint_test: Add deviceID for AM64 and J7200

Nadeem Athani (1):
PCI: cadence: Add quirk flag to set minimum delay in LTSSM
Detect.Quiet state

 drivers/misc/pci_endpoint_test.c              | 27 ++++++--
 drivers/pci/controller/cadence/pci-j721e.c    | 63 +++++++++++++++++--
 .../pci/controller/cadence/pcie-cadence-ep.c  |  4 ++
 .../controller/cadence/pcie-cadence-host.c    |  3 +
 drivers/pci/controller/cadence/pcie-cadence.c | 17 +++++
 drivers/pci/controller/cadence/pcie-cadence.h | 15 +++++
 6 files changed, 119 insertions(+), 10 deletions(-)
Signature · 1 line
2.17.1
#1 lore raw

PATCH v3 1/5 PCI: cadence: Add quirk flag to set minimum delay in LTSSM Detect.Quiet state

From: Nadeem Athani <[email protected]>

PCIe fails to link up if SERDES lanes not used by PCIe are assigned to another protocol. For example, link training fails if lanes 2 and 3 are assigned to another protocol while lanes 0 and 1 are used for PCIe to form a two lane link. This failure is due to an incorrect tie-off on an internal status signal indicating electrical idle.

Status signals going from SERDES to PCIe Controller are tied-off when a lane is not assigned to PCIe. Signal indicating electrical idle is incorrectly tied-off to a state that indicates non-idle. As a result, PCIe sees unused lanes to be out of electrical idle and this causes LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to occur. If a receiver is not detected on the first receiver detection attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and again moves forward to Detect.Active state without waiting for 12ms as required by PCIe base specification. Since wait time in Detect.Quiet is skipped, multiple receiver detect operations are performed back-to-back without allowing time for capacitance on the transmit lines to discharge. This causes subsequent receiver detection to always fail even if a receiver gets connected eventually.

Add a quirk flag "quirk_detect_quiet_flag" to program the minimum time the LTSSM should wait on entering Detect.Quiet state here. This has to be set for J7200 as it has an incorrect tie-off on unused lanes.

---
Changes from v2:
1) Removed terminating '.' in subject
2) Modified commit log
Changes from v1:
1) Add function cdns_pcie_detect_quiet_min_delay_set in pcie-cadence.c and invoke it from host and endpoint driver file.

v2: https://lore.kernel.org/r/[email protected]
v1: https://lore.kernel.org/r/[email protected]

 .../pci/controller/cadence/pcie-cadence-ep.c    |  4 ++++
 .../pci/controller/cadence/pcie-cadence-host.c  |  3 +++
 drivers/pci/controller/cadence/pcie-cadence.c   | 17 +++++++++++++++++
 drivers/pci/controller/cadence/pcie-cadence.h   | 15 +++++++++++++++
 4 files changed, 39 insertions(+)
drivers/pci/controller/cadence/pcie-cadence-ep.c +4 -0
index 791915054ff4..e05c157afef0 100644
@@ -804,6 +804,10 @@ int cdns_pcie_ep_setup(struct cdns_pcie_ep *ep)
 	ep->irq_pci_addr = CDNS_PCIE_EP_IRQ_PCI_ADDR_NONE;
 	/* Reserve region 0 for IRQs */
 	set_bit(0, &ep->ob_region_map);
+
+	if (ep->quirk_detect_quiet_flag)
+		cdns_pcie_detect_quiet_min_delay_set(&ep->pcie);
+
 	spin_lock_init(&ep->lock);
 
 	return 0;
drivers/pci/controller/cadence/pcie-cadence-host.c +3 -0
index ae1c55503513..fb96d37a135c 100644
@@ -498,6 +498,9 @@ int cdns_pcie_host_setup(struct cdns_pcie_rc *rc)
 		return PTR_ERR(rc->cfg_base);
 	rc->cfg_res = res;
 
+	if (rc->quirk_detect_quiet_flag)
+		cdns_pcie_detect_quiet_min_delay_set(&rc->pcie);
+
 	ret = cdns_pcie_start_link(pcie);
 	if (ret) {
 		dev_err(dev, "Failed to start link\n");
drivers/pci/controller/cadence/pcie-cadence.c +17 -0
index 3c3646502d05..65b6c8bed0d4 100644
@@ -7,6 +7,23 @@
 
 #include "pcie-cadence.h"
 
+void cdns_pcie_detect_quiet_min_delay_set(struct cdns_pcie *pcie)
+{
+	u32 delay = 0x3;
+	u32 ltssm_control_cap;
+
+	/*
+	 * Set the LTSSM Detect Quiet state min. delay to 2ms.
+	 */
+
+	ltssm_control_cap = cdns_pcie_readl(pcie, CDNS_PCIE_LTSSM_CONTROL_CAP);
+	ltssm_control_cap = ((ltssm_control_cap &
+			    ~CDNS_PCIE_DETECT_QUIET_MIN_DELAY_MASK) |
+			    CDNS_PCIE_DETECT_QUIET_MIN_DELAY(delay));
+
+	cdns_pcie_writel(pcie, CDNS_PCIE_LTSSM_CONTROL_CAP, ltssm_control_cap);
+}
+
 void cdns_pcie_set_outbound_region(struct cdns_pcie *pcie, u8 busnr, u8 fn,
 				   u32 r, bool is_io,
 				   u64 cpu_addr, u64 pci_addr, size_t size)
drivers/pci/controller/cadence/pcie-cadence.h +15 -0
index 22ff4c9defd8..07d461f839be 100644
@@ -194,6 +194,14 @@
 /* AXI link down register */
 #define CDNS_PCIE_AT_LINKDOWN (CDNS_PCIE_AT_BASE + 0x0824)
 
+/* LTSSM Capabilities register */
+#define CDNS_PCIE_LTSSM_CONTROL_CAP             (CDNS_PCIE_LM_BASE + 0x0054)
+#define  CDNS_PCIE_DETECT_QUIET_MIN_DELAY_MASK  GENMASK(2, 1)
+#define  CDNS_PCIE_DETECT_QUIET_MIN_DELAY_SHIFT 1
+#define  CDNS_PCIE_DETECT_QUIET_MIN_DELAY(delay) \
+	 (((delay) << CDNS_PCIE_DETECT_QUIET_MIN_DELAY_SHIFT) & \
+	 CDNS_PCIE_DETECT_QUIET_MIN_DELAY_MASK)
+
 enum cdns_pcie_rp_bar {
 	RP_BAR_UNDEFINED = -1,
 	RP_BAR0,
@@ -297,6 +305,7 @@ struct cdns_pcie {
  * @avail_ib_bar: Satus of RP_BAR0, RP_BAR1 and	RP_NO_BAR if it's free or
  *                available
  * @quirk_retrain_flag: Retrain link as quirk for PCIe Gen2
+ * @quirk_detect_quiet_flag: LTSSM Detect Quiet min delay set as quirk
  */
 struct cdns_pcie_rc {
 	struct cdns_pcie	pcie;
@@ -306,6 +315,7 @@ struct cdns_pcie_rc {
 	u32			device_id;
 	bool			avail_ib_bar[CDNS_PCIE_RP_MAX_IB];
 	bool                    quirk_retrain_flag;
+	bool                    quirk_detect_quiet_flag;
 };
 
 /**
@@ -338,6 +348,7 @@ struct cdns_pcie_epf {
  *        registers fields (RMW) accessible by both remote RC and EP to
  *        minimize time between read and write
  * @epf: Structure to hold info about endpoint function
+ * @quirk_detect_quiet_flag: LTSSM Detect Quiet min delay set as quirk
  */
 struct cdns_pcie_ep {
 	struct cdns_pcie	pcie;
@@ -352,6 +363,7 @@ struct cdns_pcie_ep {
 	/* protect writing to PCI_STATUS while raising legacy interrupts */
 	spinlock_t		lock;
 	struct cdns_pcie_epf	*epf;
+	bool                    quirk_detect_quiet_flag;
 };
 
 
@@ -512,6 +524,9 @@ static inline int cdns_pcie_ep_setup(struct cdns_pcie_ep *ep)
 	return 0;
 }
 #endif
+
+void cdns_pcie_detect_quiet_min_delay_set(struct cdns_pcie *pcie);
+
 void cdns_pcie_set_outbound_region(struct cdns_pcie *pcie, u8 busnr, u8 fn,
 				   u32 r, bool is_io,
 				   u64 cpu_addr, u64 pci_addr, size_t size);
Signature · 1 line
2.17.1
#2 lore raw

PATCH 2/5 PCI: j721e: Add PCIe support for J7200

In reply to Kishon Vijay Abraham I

J7200 has the same PCIe IP as in J721E with minor changes in the wrapper. J7200 allows byte access of bridge configuration space registers and the register field for LINK_DOWN interrupt is different. J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these changes as part of driver data applicable only to J7200.

---
 drivers/pci/controller/cadence/pci-j721e.c | 44 ++++++++++++++++++++--
 1 file changed, 40 insertions(+), 4 deletions(-)
drivers/pci/controller/cadence/pci-j721e.c +40 -4
index 35e61048e133..803da33b86d8 100644
@@ -27,6 +27,7 @@
 #define STATUS_REG_SYS_2	0x508
 #define STATUS_CLR_REG_SYS_2	0x708
 #define LINK_DOWN		BIT(1)
+#define J7200_LINK_DOWN		BIT(10)
 
 #define J721E_PCIE_USER_CMD_STATUS	0x4
 #define LINK_TRAINING_ENABLE		BIT(0)
@@ -57,6 +58,7 @@ struct j721e_pcie {
 	struct cdns_pcie	*cdns_pcie;
 	void __iomem		*user_cfg_base;
 	void __iomem		*intd_cfg_base;
+	u32			link_irq_reg_field;
 };
 
 enum j721e_pcie_mode {
@@ -67,6 +69,9 @@ enum j721e_pcie_mode {
 struct j721e_pcie_data {
 	enum j721e_pcie_mode	mode;
 	bool quirk_retrain_flag;
+	bool			quirk_detect_quiet_flag;
+	u32			link_irq_reg_field;
+	bool			byte_access_allowed;
 };
 
 static inline u32 j721e_pcie_user_readl(struct j721e_pcie *pcie, u32 offset)
@@ -98,12 +103,12 @@ static irqreturn_t j721e_pcie_link_irq_handler(int irq, void *priv)
 	u32 reg;
 
 	reg = j721e_pcie_intd_readl(pcie, STATUS_REG_SYS_2);
-	if (!(reg & LINK_DOWN))
+	if (!(reg & pcie->link_irq_reg_field))
 		return IRQ_NONE;
 
 	dev_err(dev, "LINK DOWN!\n");
 
-	j721e_pcie_intd_writel(pcie, STATUS_CLR_REG_SYS_2, LINK_DOWN);
+	j721e_pcie_intd_writel(pcie, STATUS_CLR_REG_SYS_2, pcie->link_irq_reg_field);
 	return IRQ_HANDLED;
 }
 
@@ -112,7 +117,7 @@ static void j721e_pcie_config_link_irq(struct j721e_pcie *pcie)
 	u32 reg;
 
 	reg = j721e_pcie_intd_readl(pcie, ENABLE_REG_SYS_2);
-	reg |= LINK_DOWN;
+	reg |= pcie->link_irq_reg_field;
 	j721e_pcie_intd_writel(pcie, ENABLE_REG_SYS_2, reg);
 }
 
@@ -284,10 +289,25 @@ static struct pci_ops cdns_ti_pcie_host_ops = {
 static const struct j721e_pcie_data j721e_pcie_rc_data = {
 	.mode = PCI_MODE_RC,
 	.quirk_retrain_flag = true,
+	.byte_access_allowed = false,
+	.link_irq_reg_field = LINK_DOWN,
 };
 
 static const struct j721e_pcie_data j721e_pcie_ep_data = {
 	.mode = PCI_MODE_EP,
+	.link_irq_reg_field = LINK_DOWN,
+};
+
+static const struct j721e_pcie_data j7200_pcie_rc_data = {
+	.mode = PCI_MODE_RC,
+	.quirk_detect_quiet_flag = true,
+	.link_irq_reg_field = J7200_LINK_DOWN,
+	.byte_access_allowed = true,
+};
+
+static const struct j721e_pcie_data j7200_pcie_ep_data = {
+	.mode = PCI_MODE_EP,
+	.quirk_detect_quiet_flag = true,
 };
 
 static const struct of_device_id of_j721e_pcie_match[] = {
@@ -299,6 +319,14 @@ static const struct of_device_id of_j721e_pcie_match[] = {
 		.compatible = "ti,j721e-pcie-ep",
 		.data = &j721e_pcie_ep_data,
 	},
+	{
+		.compatible = "ti,j7200-pcie-host",
+		.data = &j7200_pcie_rc_data,
+	},
+	{
+		.compatible = "ti,j7200-pcie-ep",
+		.data = &j7200_pcie_ep_data,
+	},
 	{},
 };
 
@@ -309,10 +337,12 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 	struct pci_host_bridge *bridge;
 	struct j721e_pcie_data *data;
 	struct cdns_pcie *cdns_pcie;
+	bool byte_access_allowed;
 	struct j721e_pcie *pcie;
 	struct cdns_pcie_rc *rc;
 	struct cdns_pcie_ep *ep;
 	struct gpio_desc *gpiod;
+	u32 link_irq_reg_field;
 	void __iomem *base;
 	struct clk *clk;
 	u32 num_lanes;
@@ -325,6 +355,8 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 		return -EINVAL;
 
 	mode = (u32)data->mode;
+	byte_access_allowed = data->byte_access_allowed;
+	link_irq_reg_field = data->link_irq_reg_field;
 
 	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
 	if (!pcie)
@@ -332,6 +364,7 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 
 	pcie->dev = dev;
 	pcie->mode = mode;
+	pcie->link_irq_reg_field = link_irq_reg_field;
 
 	base = devm_platform_ioremap_resource_byname(pdev, "intd_cfg");
 	if (IS_ERR(base))
@@ -391,9 +424,11 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 			goto err_get_sync;
 		}
 
-		bridge->ops = &cdns_ti_pcie_host_ops;
+		if (!byte_access_allowed)
+			bridge->ops = &cdns_ti_pcie_host_ops;
 		rc = pci_host_bridge_priv(bridge);
 		rc->quirk_retrain_flag = data->quirk_retrain_flag;
+		rc->quirk_detect_quiet_flag = data->quirk_detect_quiet_flag;
 
 		cdns_pcie = &rc->pcie;
 		cdns_pcie->dev = dev;
@@ -459,6 +494,7 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 			ret = -ENOMEM;
 			goto err_get_sync;
 		}
+		ep->quirk_detect_quiet_flag = data->quirk_detect_quiet_flag;
 
 		cdns_pcie = &ep->pcie;
 		cdns_pcie->dev = dev;
Signature · 1 line
2.17.1
#3 lore raw

Re: [PATCH 2/5] PCI: j721e: Add PCIe support for J7200

Quoted 24 lines · Kishon Vijay Abraham I

J7200 has the same PCIe IP as in J721E with minor changes in the wrapper. J7200 allows byte access of bridge configuration space registers and the register field for LINK_DOWN interrupt is different. J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these changes as part of driver data applicable only to J7200.

---
 drivers/pci/controller/cadence/pci-j721e.c | 44 ++++++++++++++++++++--
 1 file changed, 40 insertions(+), 4 deletions(-)
drivers/pci/controller/cadence/pci-j721e.c +1 -0
index 35e61048e133..803da33b86d8 100644
@@ -27,6 +27,7 @@
 #define STATUS_REG_SYS_2	0x508
 #define STATUS_CLR_REG_SYS_2	0x708
 #define LINK_DOWN		BIT(1)
+#define J7200_LINK_DOWN		BIT(10)
 
 #define J721E_PCIE_USER_CMD_STATUS	0x4
 #define LINK_TRAINING_ENABLE		BIT(0)

drivers/pci/controller/cadence/pci-j721e.c struct j721e_pcie { · line 61

Quoted 4 lines
drivers/pci/controller/cadence/pci-j721e.c +1 -0
@@ -57,6 +58,7 @@ struct j721e_pcie {
 	struct cdns_pcie	*cdns_pcie;
 	void __iomem		*user_cfg_base;
 	void __iomem		*intd_cfg_base;
+	u32			link_irq_reg_field;

This seems to be a device-specific "link down" bit, so maybe a more descriptive name that suggests "link down"?

drivers/pci/controller/cadence/pci-j721e.c enum j721e_pcie_mode { · line 74

Quoted 10 lines
drivers/pci/controller/cadence/pci-j721e.c +3 -0
 };
 
 enum j721e_pcie_mode {
@@ -67,6 +69,9 @@ enum j721e_pcie_mode {
 struct j721e_pcie_data {
 	enum j721e_pcie_mode	mode;
 	bool quirk_retrain_flag;
+	bool			quirk_detect_quiet_flag;
+	u32			link_irq_reg_field;
+	bool			byte_access_allowed;

Maybe re-indent quirk_retrain_flag so the struct is consistent?

I know there's a pattern of using "bool" in these structs, but I don't think it's really any better than "unsigned int :1" and it takes more space.

https://lore.kernel.org/r/CA+55aFzKQ6Pj18TB8p4Yr0M4t+S+BsiHH=BJNmn=76-NcjTj-g@mail.gmail.com/
https://lore.kernel.org/r/CA+55aFxnePDimkVKVtv3gNmRGcwc8KQ5mHYvUxY8sAQg6yvVYg@mail.gmail.com/

Quoted 99 lines
drivers/pci/controller/cadence/pci-j721e.c +31 -3
 };
 
 static inline u32 j721e_pcie_user_readl(struct j721e_pcie *pcie, u32 offset)
@@ -98,12 +103,12 @@ static irqreturn_t j721e_pcie_link_irq_handler(int irq, void *priv)
 	u32 reg;
 
 	reg = j721e_pcie_intd_readl(pcie, STATUS_REG_SYS_2);
-	if (!(reg & LINK_DOWN))
+	if (!(reg & pcie->link_irq_reg_field))
 		return IRQ_NONE;
 
 	dev_err(dev, "LINK DOWN!\n");
 
-	j721e_pcie_intd_writel(pcie, STATUS_CLR_REG_SYS_2, LINK_DOWN);
+	j721e_pcie_intd_writel(pcie, STATUS_CLR_REG_SYS_2, pcie->link_irq_reg_field);
 	return IRQ_HANDLED;
 }
 
@@ -112,7 +117,7 @@ static void j721e_pcie_config_link_irq(struct j721e_pcie *pcie)
 	u32 reg;
 
 	reg = j721e_pcie_intd_readl(pcie, ENABLE_REG_SYS_2);
-	reg |= LINK_DOWN;
+	reg |= pcie->link_irq_reg_field;
 	j721e_pcie_intd_writel(pcie, ENABLE_REG_SYS_2, reg);
 }
 
@@ -284,10 +289,25 @@ static struct pci_ops cdns_ti_pcie_host_ops = {
 static const struct j721e_pcie_data j721e_pcie_rc_data = {
 	.mode = PCI_MODE_RC,
 	.quirk_retrain_flag = true,
+	.byte_access_allowed = false,
+	.link_irq_reg_field = LINK_DOWN,
 };
 
 static const struct j721e_pcie_data j721e_pcie_ep_data = {
 	.mode = PCI_MODE_EP,
+	.link_irq_reg_field = LINK_DOWN,
+};
+
+static const struct j721e_pcie_data j7200_pcie_rc_data = {
+	.mode = PCI_MODE_RC,
+	.quirk_detect_quiet_flag = true,
+	.link_irq_reg_field = J7200_LINK_DOWN,
+	.byte_access_allowed = true,
+};
+
+static const struct j721e_pcie_data j7200_pcie_ep_data = {
+	.mode = PCI_MODE_EP,
+	.quirk_detect_quiet_flag = true,
 };
 
 static const struct of_device_id of_j721e_pcie_match[] = {
@@ -299,6 +319,14 @@ static const struct of_device_id of_j721e_pcie_match[] = {
 		.compatible = "ti,j721e-pcie-ep",
 		.data = &j721e_pcie_ep_data,
 	},
+	{
+		.compatible = "ti,j7200-pcie-host",
+		.data = &j7200_pcie_rc_data,
+	},
+	{
+		.compatible = "ti,j7200-pcie-ep",
+		.data = &j7200_pcie_ep_data,
+	},
 	{},
 };
 
@@ -309,10 +337,12 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 	struct pci_host_bridge *bridge;
 	struct j721e_pcie_data *data;
 	struct cdns_pcie *cdns_pcie;
+	bool byte_access_allowed;
 	struct j721e_pcie *pcie;
 	struct cdns_pcie_rc *rc;
 	struct cdns_pcie_ep *ep;
 	struct gpio_desc *gpiod;
+	u32 link_irq_reg_field;
 	void __iomem *base;
 	struct clk *clk;
 	u32 num_lanes;
@@ -325,6 +355,8 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 		return -EINVAL;
 
 	mode = (u32)data->mode;
+	byte_access_allowed = data->byte_access_allowed;
+	link_irq_reg_field = data->link_irq_reg_field;
 
 	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
 	if (!pcie)
@@ -332,6 +364,7 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 
 	pcie->dev = dev;
 	pcie->mode = mode;
+	pcie->link_irq_reg_field = link_irq_reg_field;
 
 	base = devm_platform_ioremap_resource_byname(pdev, "intd_cfg");
 	if (IS_ERR(base))

drivers/pci/controller/cadence/pci-j721e.c static int j721e_pcie_probe(struct platform_device *pdev) · line 427

Quoted 5 lines
drivers/pci/controller/cadence/pci-j721e.c +1 -1
@@ -391,9 +424,11 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 			goto err_get_sync;
 		}
 
-		bridge->ops = &cdns_ti_pcie_host_ops;
+		if (!byte_access_allowed)

Why bother with the "byte_access_allowed" local variable? Could just use "data->byte_access_allowed" here, as the code below uses "data->quirk_retrain_flag", etc.

Same with "link_irq_reg_field" above, I guess.

Quoted 18 lines
drivers/pci/controller/cadence/pci-j721e.c +3 -0
+			bridge->ops = &cdns_ti_pcie_host_ops;
 		rc = pci_host_bridge_priv(bridge);
 		rc->quirk_retrain_flag = data->quirk_retrain_flag;
+		rc->quirk_detect_quiet_flag = data->quirk_detect_quiet_flag;
 
 		cdns_pcie = &rc->pcie;
 		cdns_pcie->dev = dev;
@@ -459,6 +494,7 @@ static int j721e_pcie_probe(struct platform_device *pdev)
 			ret = -ENOMEM;
 			goto err_get_sync;
 		}
+		ep->quirk_detect_quiet_flag = data->quirk_detect_quiet_flag;
 
 		cdns_pcie = &ep->pcie;
 		cdns_pcie->dev = dev;
Signature · 1 line
2.17.1
#4 lore raw

PATCH 3/5 PCI: j721e: Add PCIe support for AM64

In reply to Kishon Vijay Abraham I

AM64 has the same PCIe IP as in J7200 with certain erratas not applicable (quirk_detect_quiet_flag). Add support for "ti,am64-pcie-host" compatible and "ti,am64-pcie-ep" compatible that is specific to AM64.

---
 drivers/pci/controller/cadence/pci-j721e.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
drivers/pci/controller/cadence/pci-j721e.c +19 -0
index 803da33b86d8..3156b28ae8ab 100644
@@ -310,6 +310,17 @@ static const struct j721e_pcie_data j7200_pcie_ep_data = {
 	.quirk_detect_quiet_flag = true,
 };
 
+static const struct j721e_pcie_data am64_pcie_rc_data = {
+	.mode = PCI_MODE_RC,
+	.link_irq_reg_field = J7200_LINK_DOWN,
+	.byte_access_allowed = true,
+};
+
+static const struct j721e_pcie_data am64_pcie_ep_data = {
+	.mode = PCI_MODE_EP,
+	.link_irq_reg_field = J7200_LINK_DOWN,
+};
+
 static const struct of_device_id of_j721e_pcie_match[] = {
 	{
 		.compatible = "ti,j721e-pcie-host",
@@ -327,6 +338,14 @@ static const struct of_device_id of_j721e_pcie_match[] = {
 		.compatible = "ti,j7200-pcie-ep",
 		.data = &j7200_pcie_ep_data,
 	},
+	{
+		.compatible = "ti,am64-pcie-host",
+		.data = &am64_pcie_rc_data,
+	},
+	{
+		.compatible = "ti,am64-pcie-ep",
+		.data = &am64_pcie_ep_data,
+	},
 	{},
 };
 
Signature · 1 line
2.17.1
#5 lore raw

PATCH 4/5 misc: pci_endpoint_test: Do not request or allocate IRQs in probe

In reply to Kishon Vijay Abraham I

Allocation of IRQ vectors and requesting IRQ is done as part of PCITEST_SET_IRQTYPE. Do not request or allocate IRQs in probe for AM654 and J721E so that the user space test script has better control of the devices for which the IRQs are configured. Since certain user space scripts could rely on allocation of IRQ vectors during probe, remove allocation of IRQs only for TI's K3 platform.

---
 drivers/misc/pci_endpoint_test.c | 19 +++++++++++++------
 1 file changed, 13 insertions(+), 6 deletions(-)
drivers/misc/pci_endpoint_test.c +13 -6
index c7ee34013485..9740f2a0e7cd 100644
@@ -79,6 +79,9 @@
 #define PCI_DEVICE_ID_RENESAS_R8A774C0		0x002d
 #define PCI_DEVICE_ID_RENESAS_R8A774E1		0x0025
 
+#define is_j721e_pci_dev(pdev)         \
+		((pdev)->device == PCI_DEVICE_ID_TI_J721E)
+
 static DEFINE_IDA(pci_endpoint_test_ida);
 
 #define to_endpoint_test(priv) container_of((priv), struct pci_endpoint_test, \
@@ -810,9 +813,11 @@ static int pci_endpoint_test_probe(struct pci_dev *pdev,
 
 	pci_set_master(pdev);
 
-	if (!pci_endpoint_test_alloc_irq_vectors(test, irq_type)) {
-		err = -EINVAL;
-		goto err_disable_irq;
+	if (!(is_am654_pci_dev(pdev) || is_j721e_pci_dev(pdev))) {
+		if (!pci_endpoint_test_alloc_irq_vectors(test, irq_type)) {
+			err = -EINVAL;
+			goto err_disable_irq;
+		}
 	}
 
 	for (bar = 0; bar < PCI_STD_NUM_BARS; bar++) {
@@ -850,9 +855,11 @@ static int pci_endpoint_test_probe(struct pci_dev *pdev,
 		goto err_ida_remove;
 	}
 
-	if (!pci_endpoint_test_request_irq(test)) {
-		err = -EINVAL;
-		goto err_kfree_test_name;
+	if (!(is_am654_pci_dev(pdev) || is_j721e_pci_dev(pdev))) {
+		if (!pci_endpoint_test_request_irq(test)) {
+			err = -EINVAL;
+			goto err_kfree_test_name;
+		}
 	}
 
 	misc_device = &test->miscdev;
Signature · 1 line
2.17.1
#6 lore raw

PATCH 5/5 misc: pci_endpoint_test: Add deviceID for AM64 and J7200

In reply to Kishon Vijay Abraham I

Add device ID specific to AM64 and J7200 in pci_endpoint_test so that endpoints configured with those deviceIDs can use pci_endpoint_test driver.

---
 drivers/misc/pci_endpoint_test.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/misc/pci_endpoint_test.c +8 -0
index 9740f2a0e7cd..707cf9d7e8c0 100644
@@ -69,6 +69,8 @@
 #define FLAG_USE_DMA				BIT(0)
 
 #define PCI_DEVICE_ID_TI_AM654			0xb00c
+#define PCI_DEVICE_ID_TI_J7200			0xb00f
+#define PCI_DEVICE_ID_TI_AM64			0xb010
 #define PCI_DEVICE_ID_LS1088A			0x80c0
 
 #define is_am654_pci_dev(pdev)		\
@@ -976,6 +978,12 @@ static const struct pci_device_id pci_endpoint_test_tbl[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_J721E),
 	  .driver_data = (kernel_ulong_t)&j721e_data,
 	},
+	{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_J7200),
+	  .driver_data = (kernel_ulong_t)&j721e_data,
+	},
+	{ PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_AM64),
+	  .driver_data = (kernel_ulong_t)&j721e_data,
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(pci, pci_endpoint_test_tbl);
Signature · 1 line
2.17.1