Add support for eMMC on ST-Ericsson Ux500(v2)
cover Add support for eMMC on ST-Ericsson Ux500(v2)
This patch series adds support for the eMMC on ST-Ericsson Ux500:
1. Some minor fixes+cleanup for the arm_pl180_mmci driver.
3. Add the necessary configuration for ST-Ericsson Ux500v2.
This was tested on the u8500 "stemmy" board that is already present in U-Boot.
Stephan Gerhold (4):
mmc: arm_pl180_mmci: Don't bind to all arm,primecell devices
mmc: arm_pl180_mmci: Simplify code using dev_read_addr_ptr()
mmc: arm_pl180_mmci: Simplify code using mmc_of_parse()
mmc: arm_pl180_mmci: Add configuration for ST-Ericsson Ux500v2
drivers/mmc/arm_pl180_mmci.c | 48 ++++++++++++++++-------------------- drivers/mmc/arm_pl180_mmci.h | 1 + 2 files changed, 22 insertions(+), 27 deletions(-)
Signature · 1 line
2.32.0
PATCH 1/4 mmc: arm_pl180_mmci: Don't bind to all arm, primecell devices
The arm,primecell compatible is used for lots of different types of devices, e.g. I2C, SPI, coresight, ... We really should not bind the MMC driver to all of them.
Looking through the device trees in U-Boot there seems to be always a second compatible string for the pl180 device, either arm,pl180 (already listed) or arm,pl18x. Add the "arm,pl18x" compatible to the list but remove the generic "arm,primecell".
Note that on Linux these compatibles cannot be found in drivers because AMBA/primecell devices are matched based on their peripheral ID instead of the compatible.
This fixes the following error messages when booting the ST-Ericsson U8500 "stemmy" board with the arm_pl180_mmci driver enabled:
MMC: ptm@801ae000 - probe failed: -38
ptm@801af000 - probe failed: -38
funnel@801a6000 - probe failed: -38
tpiu@80190000 - probe failed: -38
etb@801a4000 - probe failed: -38
---
drivers/mmc/arm_pl180_mmci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mmc/arm_pl180_mmci.c +1 -1
@@ -539,7 +539,7 @@ static int arm_pl180_mmc_of_to_plat(struct udevice *dev)static const struct udevice_id arm_pl180_mmc_match[] = { { .compatible ="arm,pl180" }, - { .compatible ="arm,primecell" }, + { .compatible ="arm,pl18x" }, {/* sentinel */ } };
Signature · 1 line
2.32.0
Re: [PATCH 1/4] mmc: arm_pl180_mmci: Don't bind to all arm, primecell devices
Hi Stephan
Quoted 36 lines · Stephan Gerhold
The arm,primecell compatible is used for lots of different types of devices, e.g. I2C, SPI, coresight, ... We really should not bind the MMC driver to all of them.
Looking through the device trees in U-Boot there seems to be always a second compatible string for the pl180 device, either arm,pl180 (already listed) or arm,pl18x. Add the "arm,pl18x" compatible to the list but remove the generic "arm,primecell".
Note that on Linux these compatibles cannot be found in drivers because AMBA/primecell devices are matched based on their peripheral ID instead of the compatible.
This fixes the following error messages when booting the ST-Ericsson U8500 "stemmy" board with the
arm_pl180_mmcidriver enabled:MMC: ptm@801ae000 - probe failed: -38
ptm@801af000 - probe failed: -38
funnel@801a6000 - probe failed: -38
tpiu@80190000 - probe failed: -38
etb@801a4000 - probe failed: -38Cc Patrice Chotard <[email protected]>Fixes 6f41d1a17e20 ("mmc: arm_pl180_mmci: Sync compatible with kernel")Signed-off-by Stephan Gerhold <[email protected]>---
drivers/mmc/arm_pl180_mmci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/mmc/arm_pl180_mmci.c +0
-0
drivers/mmc/arm_pl180_mmci.c static int arm_pl180_mmc_of_to_plat(struct udevice *dev) · line 545
Quoted 8 lines
drivers/mmc/arm_pl180_mmci.c +1
-1@@ -539,7 +539,7 @@ static int arm_pl180_mmc_of_to_plat(struct udevice *dev)static const struct udevice_id arm_pl180_mmc_match[] = { { .compatible ="arm,pl180" }, - { .compatible ="arm,primecell" }, + { .compatible ="arm,pl18x" }, {/* sentinel */ } };
Thanks
Patrice
Re: [PATCH 1/4] mmc: arm_pl180_mmci: Don't bind to all arm,primecell devices
In reply to Stephan GerholdQuoted 22 lines · Stephan Gerhold
The arm,primecell compatible is used for lots of different types of devices, e.g. I2C, SPI, coresight, ... We really should not bind the MMC driver to all of them.
Looking through the device trees in U-Boot there seems to be always a second compatible string for the pl180 device, either arm,pl180 (already listed) or arm,pl18x. Add the "arm,pl18x" compatible to the list but remove the generic "arm,primecell".
Note that on Linux these compatibles cannot be found in drivers because AMBA/primecell devices are matched based on their peripheral ID instead of the compatible.
This fixes the following error messages when booting the ST-Ericsson U8500 "stemmy" board with the
arm_pl180_mmcidriver enabled:MMC: ptm@801ae000 - probe failed: -38
ptm@801af000 - probe failed: -38
funnel@801a6000 - probe failed: -38
tpiu@80190000 - probe failed: -38
etb@801a4000 - probe failed: -38
Quoted 3 lines
Cc Patrice Chotard <[email protected]>Fixes 6f41d1a17e20 ("mmc: arm_pl180_mmci: Sync compatible with kernel")Signed-off-by Stephan Gerhold <[email protected]>
Best Regards,
Jaehoon Chung
Quoted 19 lines
---
drivers/mmc/arm_pl180_mmci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/mmc/arm_pl180_mmci.c +1
-1@@ -539,7 +539,7 @@ static int arm_pl180_mmc_of_to_plat(struct udevice *dev)static const struct udevice_id arm_pl180_mmc_match[] = { { .compatible ="arm,pl180" }, - { .compatible ="arm,primecell" }, + { .compatible ="arm,pl18x" }, {/* sentinel */ } };
PATCH 2/4 mmc: arm_pl180_mmci: Simplify code using dev_read_addr_ptr()
In reply to Stephan GerholdSimplify the code a bit by using dev_read_addr_ptr() instead of dev_read_addr(). This avoids having to cast explicitly to void*.
---
drivers/mmc/arm_pl180_mmci.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-)
drivers/mmc/arm_pl180_mmci.c +2 -5
@@ -526,14 +526,11 @@ static const struct dm_mmc_ops arm_pl180_dm_mmc_ops = {static int arm_pl180_mmc_of_to_plat (struct udevice *dev) {struct pl180_mmc_host *host =dev_get_priv (dev); -fdt_addr_t addr; - addr =dev_read_addr (dev); -if (addr ==FDT_ADDR_T_NONE ) + host->base =dev_read_addr_ptr (dev); +if (!host->base)return -EINVAL ; - host->base = (void *)addr; -return 0 ; }
Signature · 1 line
2.32.0
Re: [PATCH 2/4] mmc: arm_pl180_mmci: Simplify code using dev_read_addr_ptr()
Hi Stephan
Quoted 21 lines · Stephan Gerhold
Simplify the code a bit by using
dev_read_addr_ptr()instead ofdev_read_addr(). This avoids having to cast explicitly to void*.Signed-off-by Stephan Gerhold <[email protected]>---
drivers/mmc/arm_pl180_mmci.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-)drivers/mmc/arm_pl180_mmci.c +0
-2@@ -526,14 +526,11 @@ static const struct dm_mmc_ops arm_pl180_dm_mmc_ops = {static int arm_pl180_mmc_of_to_plat (struct udevice *dev) {struct pl180_mmc_host *host =dev_get_priv (dev); -fdt_addr_t addr; - addr =dev_read_addr (dev);
drivers/mmc/arm_pl180_mmci.c static const struct dm_mmc_ops arm_pl180_dm_mmc_ops = { · line 536
Quoted 10 lines
drivers/mmc/arm_pl180_mmci.c +2
-3-if (addr ==FDT_ADDR_T_NONE ) + host->base =dev_read_addr_ptr (dev); +if (!host->base)return -EINVAL ; - host->base = (void *)addr; -return 0 ; }
Thanks
Patrice
Re: [PATCH 2/4] mmc: arm_pl180_mmci: Simplify code using dev_read_addr_ptr()
In reply to Stephan GerholdQuoted 4 lines · Stephan Gerhold
Simplify the code a bit by using
dev_read_addr_ptr()instead ofdev_read_addr(). This avoids having to cast explicitly to void*.Signed-off-by Stephan Gerhold <[email protected]>
Best Regards,
Jaehoon Chung
Quoted 27 lines
---
drivers/mmc/arm_pl180_mmci.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-)drivers/mmc/arm_pl180_mmci.c +2
-5@@ -526,14 +526,11 @@ static const struct dm_mmc_ops arm_pl180_dm_mmc_ops = {static int arm_pl180_mmc_of_to_plat (struct udevice *dev) {struct pl180_mmc_host *host =dev_get_priv (dev); -fdt_addr_t addr; - addr =dev_read_addr (dev); -if (addr ==FDT_ADDR_T_NONE ) + host->base =dev_read_addr_ptr (dev); +if (!host->base)return -EINVAL ; - host->base = (void *)addr; -return 0 ; }
PATCH 3/4 mmc: arm_pl180_mmci: Simplify code using mmc_of_parse()
In reply to Stephan GerholdSimplify the code a bit by using the common mmc_of_parse() function instead of duplicating the device tree parsing code. We can still get a default value for cfg->f_max by assigning it before calling mmc_of_parse().
Another advantage of this refactoring is that we parse more properties now, e.g. "non-removable" can be used to disable CD entirely.
---
drivers/mmc/arm_pl180_mmci.c | 19 ++++--------------- 1 file changed, 4 insertions(+), 15 deletions(-)
drivers/mmc/arm_pl180_mmci.c +4 -15
@@ -424,7 +424,6 @@ static int arm_pl180_mmc_probe(struct udevice *dev)struct pl180_mmc_host *host =dev_get_priv (dev);struct mmc_config *cfg = &pdata->cfg;struct clk clk; -u32 bus_width;u32 periphid;int ret;
@@ -457,24 +456,14 @@ static int arm_pl180_mmc_probe(struct udevice *dev) cfg->voltages =VOLTAGE_WINDOW_SD ; cfg->host_caps =0 ; cfg->f_min = host->clock_in / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 +1 )); - cfg->f_max =dev_read_u32_default (dev,"max-frequency" ,MMC_CLOCK_MAX ); + cfg->f_max =MMC_CLOCK_MAX ; cfg->b_max =CONFIG_SYS_MMC_MAX_BLK_COUNT ;gpio_request_by_name (dev,"cd-gpios" ,0 , &host->cd_gpio,GPIOD_IS_IN ); - bus_width =dev_read_u32_default (dev,"bus-width" ,1 ); -switch (bus_width) { -case 8 : - cfg->host_caps |=MMC_MODE_8BIT ; -/* Hosts capable of 8-bit transfers can also do 4 bits */ -case 4 : - cfg->host_caps |=MMC_MODE_4BIT ; -break ; -case 1 : -break ; -default : -dev_err (dev,"Invalid bus-width value %u\n" , bus_width); - } + ret =mmc_of_parse (dev, cfg); +if (ret) +return ret;arm_pl180_mmc_init (host); mmc->priv = host;
Signature · 1 line
2.32.0
Re: [PATCH 3/4] mmc: arm_pl180_mmci: Simplify code using mmc_of_parse()
Hi Stephan
Quoted 46 lines · Stephan Gerhold
Simplify the code a bit by using the common
mmc_of_parse()function instead of duplicating the device tree parsing code. We can still get a default value forcfg->f_maxby assigning it before callingmmc_of_parse().Another advantage of this refactoring is that we parse more properties now, e.g. "non-removable" can be used to disable CD entirely.
Signed-off-by Stephan Gerhold <[email protected]>---
drivers/mmc/arm_pl180_mmci.c | 19 ++++--------------- 1 file changed, 4 insertions(+), 15 deletions(-)drivers/mmc/arm_pl180_mmci.c +1
-11@@ -424,7 +424,6 @@ static int arm_pl180_mmc_probe(struct udevice *dev)struct pl180_mmc_host *host =dev_get_priv (dev);struct mmc_config *cfg = &pdata->cfg;struct clk clk; -u32 bus_width;u32 periphid;int ret;@@ -457,24 +456,14 @@ static int arm_pl180_mmc_probe(struct udevice *dev) cfg->voltages =VOLTAGE_WINDOW_SD ; cfg->host_caps =0 ; cfg->f_min = host->clock_in / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 +1 )); - cfg->f_max =dev_read_u32_default (dev,"max-frequency" ,MMC_CLOCK_MAX ); + cfg->f_max =MMC_CLOCK_MAX ; cfg->b_max =CONFIG_SYS_MMC_MAX_BLK_COUNT ;gpio_request_by_name (dev,"cd-gpios" ,0 , &host->cd_gpio,GPIOD_IS_IN ); - bus_width =dev_read_u32_default (dev,"bus-width" ,1 ); -switch (bus_width) { -case 8 : - cfg->host_caps |=MMC_MODE_8BIT ; -/* Hosts capable of 8-bit transfers can also do 4 bits */ -case 4 : - cfg->host_caps |=MMC_MODE_4BIT ; -break ; -case 1 :
drivers/mmc/arm_pl180_mmci.c static int arm_pl180_mmc_probe(struct udevice *dev) · line 469
Quoted 10 lines
drivers/mmc/arm_pl180_mmci.c +3
-4-break ; -default : -dev_err (dev,"Invalid bus-width value %u\n" , bus_width); - } + ret =mmc_of_parse (dev, cfg); +if (ret) +return ret;arm_pl180_mmc_init (host); mmc->priv = host;
Thanks
Patrice
Re: [PATCH 3/4] mmc: arm_pl180_mmci: Simplify code using mmc_of_parse()
In reply to Stephan GerholdQuoted 9 lines · Stephan Gerhold
Simplify the code a bit by using the common
mmc_of_parse()function instead of duplicating the device tree parsing code. We can still get a default value forcfg->f_maxby assigning it before callingmmc_of_parse().Another advantage of this refactoring is that we parse more properties now, e.g. "non-removable" can be used to disable CD entirely.
Signed-off-by Stephan Gerhold <[email protected]>
Best Regards,
Jaehoon Chung
Quoted 47 lines
---
drivers/mmc/arm_pl180_mmci.c | 19 ++++--------------- 1 file changed, 4 insertions(+), 15 deletions(-)drivers/mmc/arm_pl180_mmci.c +4
-15@@ -424,7 +424,6 @@ static int arm_pl180_mmc_probe(struct udevice *dev)struct pl180_mmc_host *host =dev_get_priv (dev);struct mmc_config *cfg = &pdata->cfg;struct clk clk; -u32 bus_width;u32 periphid;int ret;@@ -457,24 +456,14 @@ static int arm_pl180_mmc_probe(struct udevice *dev) cfg->voltages =VOLTAGE_WINDOW_SD ; cfg->host_caps =0 ; cfg->f_min = host->clock_in / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 +1 )); - cfg->f_max =dev_read_u32_default (dev,"max-frequency" ,MMC_CLOCK_MAX ); + cfg->f_max =MMC_CLOCK_MAX ; cfg->b_max =CONFIG_SYS_MMC_MAX_BLK_COUNT ;gpio_request_by_name (dev,"cd-gpios" ,0 , &host->cd_gpio,GPIOD_IS_IN ); - bus_width =dev_read_u32_default (dev,"bus-width" ,1 ); -switch (bus_width) { -case 8 : - cfg->host_caps |=MMC_MODE_8BIT ; -/* Hosts capable of 8-bit transfers can also do 4 bits */ -case 4 : - cfg->host_caps |=MMC_MODE_4BIT ; -break ; -case 1 : -break ; -default : -dev_err (dev,"Invalid bus-width value %u\n" , bus_width); - } + ret =mmc_of_parse (dev, cfg); +if (ret) +return ret;arm_pl180_mmc_init (host); mmc->priv = host;
PATCH 4/4 mmc: arm_pl180_mmci: Add configuration for ST-Ericsson Ux500v2
In reply to Stephan GerholdFor the eMMC on ST-Ericsson Ux500v2 we need slightly different configuration values. Use the existing switch statement to match the peripheral ID of Ux500v2 (0x10480180) and override the necessary values to make the eMMC work on devices with ST-Ericsson Ux500.
---
drivers/mmc/arm_pl180_mmci.c | 22 +++++++++++++++------- drivers/mmc/arm_pl180_mmci.h | 1 + 2 files changed, 16 insertions(+), 7 deletions(-)
drivers/mmc/arm_pl180_mmci.c +15 -7
@@ -443,22 +443,30 @@ static int arm_pl180_mmc_probe(struct udevice *dev)SDI_CLKCR_HWFC_EN ; host->clock_in =clk_get_rate (&clk); + cfg->name = dev->name; + cfg->voltages =VOLTAGE_WINDOW_SD ; + cfg->host_caps =0 ; + cfg->f_min = host->clock_in / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 +1 )); + cfg->f_max =MMC_CLOCK_MAX ; + cfg->b_max =CONFIG_SYS_MMC_MAX_BLK_COUNT ; + periphid =dev_read_u32_default (dev,"arm,primecell-periphid" ,0 );switch (periphid) {case STM32_MMCI_ID :/* stm32 variant */ host->version2 = false;break ; +case UX500V2_MMCI_ID : + host->pwr_init =SDI_PWR_OPD |SDI_PWR_PWRCTRL_ON ; + host->clkdiv_init =SDI_CLKCR_CLKDIV_INIT_V2 |SDI_CLKCR_CLKEN | +SDI_CLKCR_HWFC_EN ; + cfg->voltages =VOLTAGE_WINDOW_MMC ; + cfg->f_min = host->clock_in / (2 +SDI_CLKCR_CLKDIV_INIT_V2 ); + host->version2 = true; +break ;default : host->version2 = true; } - cfg->name = dev->name; - cfg->voltages =VOLTAGE_WINDOW_SD ; - cfg->host_caps =0 ; - cfg->f_min = host->clock_in / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 +1 )); - cfg->f_max =MMC_CLOCK_MAX ; - cfg->b_max =CONFIG_SYS_MMC_MAX_BLK_COUNT ; -gpio_request_by_name (dev,"cd-gpios" ,0 , &host->cd_gpio,GPIOD_IS_IN ); ret =mmc_of_parse (dev, cfg);
drivers/mmc/arm_pl180_mmci.h +1 -0
@@ -142,6 +142,7 @@#define SDI_FIFO_BURST_SIZE 8#define STM32_MMCI_ID 0x00880180 +#define UX500V2_MMCI_ID 0x10480180struct sdi_registers {u32 power;/* 0x00*/
Signature · 1 line
2.32.0
Re: [PATCH 4/4] mmc: arm_pl180_mmci: Add configuration for ST-Ericsson Ux500v2
Hi Stephan
Quoted 61 lines · Stephan Gerhold
For the eMMC on ST-Ericsson Ux500v2 we need slightly different configuration values. Use the existing switch statement to match the peripheral ID of Ux500v2 (
0x10480180) and override the necessary values to make the eMMC work on devices with ST-Ericsson Ux500.Cc Linus Walleij <[email protected]>Signed-off-by Stephan Gerhold <[email protected]>---
drivers/mmc/arm_pl180_mmci.c | 22 +++++++++++++++------- drivers/mmc/arm_pl180_mmci.h | 1 + 2 files changed, 16 insertions(+), 7 deletions(-)drivers/mmc/arm_pl180_mmci.c +15
-7@@ -443,22 +443,30 @@ static int arm_pl180_mmc_probe(struct udevice *dev)SDI_CLKCR_HWFC_EN ; host->clock_in =clk_get_rate (&clk); + cfg->name = dev->name; + cfg->voltages =VOLTAGE_WINDOW_SD ; + cfg->host_caps =0 ; + cfg->f_min = host->clock_in / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 +1 )); + cfg->f_max =MMC_CLOCK_MAX ; + cfg->b_max =CONFIG_SYS_MMC_MAX_BLK_COUNT ; + periphid =dev_read_u32_default (dev,"arm,primecell-periphid" ,0 );switch (periphid) {case STM32_MMCI_ID :/* stm32 variant */ host->version2 = false;break ; +case UX500V2_MMCI_ID : + host->pwr_init =SDI_PWR_OPD |SDI_PWR_PWRCTRL_ON ; + host->clkdiv_init =SDI_CLKCR_CLKDIV_INIT_V2 |SDI_CLKCR_CLKEN | +SDI_CLKCR_HWFC_EN ; + cfg->voltages =VOLTAGE_WINDOW_MMC ; + cfg->f_min = host->clock_in / (2 +SDI_CLKCR_CLKDIV_INIT_V2 ); + host->version2 = true; +break ;default : host->version2 = true; } - cfg->name = dev->name; - cfg->voltages =VOLTAGE_WINDOW_SD ; - cfg->host_caps =0 ; - cfg->f_min = host->clock_in / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 +1 )); - cfg->f_max =MMC_CLOCK_MAX ; - cfg->b_max =CONFIG_SYS_MMC_MAX_BLK_COUNT ; -gpio_request_by_name (dev,"cd-gpios" ,0 , &host->cd_gpio,GPIOD_IS_IN ); ret =mmc_of_parse (dev, cfg);drivers/mmc/arm_pl180_mmci.h +0
-0
drivers/mmc/arm_pl180_mmci.h line 148
Quoted 7 lines
drivers/mmc/arm_pl180_mmci.h +1
-0@@ -142,6 +142,7 @@#define SDI_FIFO_BURST_SIZE 8#define STM32_MMCI_ID 0x00880180 +#define UX500V2_MMCI_ID 0x10480180struct sdi_registers {u32 power;/* 0x00*/
Thanks
Patrice
Re: [PATCH 4/4] mmc: arm_pl180_mmci: Add configuration for ST-Ericsson Ux500v2
In reply to Stephan GerholdQuoted 7 lines · Stephan Gerhold
For the eMMC on ST-Ericsson Ux500v2 we need slightly different configuration values. Use the existing switch statement to match the peripheral ID of Ux500v2 (
0x10480180) and override the necessary values to make the eMMC work on devices with ST-Ericsson Ux500.Cc Linus Walleij <[email protected]>Signed-off-by Stephan Gerhold <[email protected]>
Best Regards,
Jaehoon Chung
Quoted 61 lines
---
drivers/mmc/arm_pl180_mmci.c | 22 +++++++++++++++------- drivers/mmc/arm_pl180_mmci.h | 1 + 2 files changed, 16 insertions(+), 7 deletions(-)drivers/mmc/arm_pl180_mmci.c +15
-7@@ -443,22 +443,30 @@ static int arm_pl180_mmc_probe(struct udevice *dev)SDI_CLKCR_HWFC_EN ; host->clock_in =clk_get_rate (&clk); + cfg->name = dev->name; + cfg->voltages =VOLTAGE_WINDOW_SD ; + cfg->host_caps =0 ; + cfg->f_min = host->clock_in / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 +1 )); + cfg->f_max =MMC_CLOCK_MAX ; + cfg->b_max =CONFIG_SYS_MMC_MAX_BLK_COUNT ; + periphid =dev_read_u32_default (dev,"arm,primecell-periphid" ,0 );switch (periphid) {case STM32_MMCI_ID :/* stm32 variant */ host->version2 = false;break ; +case UX500V2_MMCI_ID : + host->pwr_init =SDI_PWR_OPD |SDI_PWR_PWRCTRL_ON ; + host->clkdiv_init =SDI_CLKCR_CLKDIV_INIT_V2 |SDI_CLKCR_CLKEN | +SDI_CLKCR_HWFC_EN ; + cfg->voltages =VOLTAGE_WINDOW_MMC ; + cfg->f_min = host->clock_in / (2 +SDI_CLKCR_CLKDIV_INIT_V2 ); + host->version2 = true; +break ;default : host->version2 = true; } - cfg->name = dev->name; - cfg->voltages =VOLTAGE_WINDOW_SD ; - cfg->host_caps =0 ; - cfg->f_min = host->clock_in / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 +1 )); - cfg->f_max =MMC_CLOCK_MAX ; - cfg->b_max =CONFIG_SYS_MMC_MAX_BLK_COUNT ; -gpio_request_by_name (dev,"cd-gpios" ,0 , &host->cd_gpio,GPIOD_IS_IN ); ret =mmc_of_parse (dev, cfg);drivers/mmc/arm_pl180_mmci.h +1
-0@@ -142,6 +142,7 @@#define SDI_FIFO_BURST_SIZE 8#define STM32_MMCI_ID 0x00880180 +#define UX500V2_MMCI_ID 0x10480180struct sdi_registers {u32 power;/* 0x00*/
Quoted 7 lines · Stephan Gerhold
This patch series adds support for the eMMC on ST-Ericsson Ux500:
1. Some minor fixes+cleanup for the
arm_pl180_mmcidriver.
3. Add the necessary configuration for ST-Ericsson Ux500v2.This was tested on the u8500 "stemmy" board that is already present in U-Boot.
The series:
Yours,
Linus Walleij