imx: ventana: remove USB_KEYBOARD support
PATCH 1/11 imx: ventana: remove USB_KEYBOARD support
For some time now having USB_KEYBOARD support has caused usb to be initialized on boot. To allow for a quicker bootup we don't want this for Ventana and don't really need USB keyboard support so remove it.
--- configs/gwventana_emmc_defconfig | 1 - configs/gwventana_gw5904_defconfig | 1 - configs/gwventana_nand_defconfig | 1 - 3 files changed, 3 deletions(-)
configs/gwventana_emmc_defconfig +0 -1
@@ -108,7 +108,6 @@ CONFIG_IMX_THERMAL=y CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_STORAGE=y -CONFIG_USB_KEYBOARD=y CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Gateworks"
configs/gwventana_gw5904_defconfig +0 -1
@@ -112,7 +112,6 @@ CONFIG_IMX_THERMAL=y CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_STORAGE=y -CONFIG_USB_KEYBOARD=y CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Gateworks"
configs/gwventana_nand_defconfig +0 -1
@@ -114,7 +114,6 @@ CONFIG_IMX_THERMAL=y CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_STORAGE=y -CONFIG_USB_KEYBOARD=y CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="Gateworks"
Signature · 1 line
2.17.1
PATCH 2/11 imx: ventana: remove unneeded includes
remove unnecessary includes
--- board/gateworks/gw_ventana/gw_ventana.c | 14 -------------- 1 file changed, 14 deletions(-)
board/gateworks/gw_ventana/gw_ventana.c +0 -14
@@ -6,37 +6,23 @@*/ #include <common.h> -#include <init.h> -#include <log.h> -#include <net.h> #include <asm/arch/clock.h> #include <asm/arch/crm_regs.h> -#include <asm/arch/iomux.h> #include <asm/arch/mx6-pins.h> #include <asm/arch/mxc_hdmi.h> #include <asm/arch/sys_proto.h> #include <asm/global_data.h> #include <asm/gpio.h> #include <asm/mach-imx/boot_mode.h> -#include <asm/mach-imx/sata.h> #include <asm/mach-imx/video.h> -#include <asm/io.h> #include <asm/setup.h> -#include <dm.h> #include <env.h> #include <hwconfig.h> -#include <i2c.h> -#include <fdt_support.h> -#include <jffs2/load_kernel.h> #include <linux/ctype.h> #include <miiphy.h> #include <mtd_node.h> -#include <pci.h> #include <linux/delay.h> -#include <linux/libfdt.h> #include <power/pmic.h> -#include <power/ltc3676_pmic.h> -#include <power/pfuze100_pmic.h> #include <fdt_support.h> #include <jffs2/load_kernel.h>
Signature · 1 line
2.17.1
PATCH 2/11 imx: ventana: remove unneeded includes
Quoted 2 lines
remove unnecessary includes
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 2/11 imx: ventana: remove unneeded includes
In reply to Tim HarveyQuoted 2 lines
remove unnecessary includes
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 3/11 imx: ventana: increase SYS_BOOTM_LEN
In reply to Tim HarveyIncrease SYS_BOOM_LEN from the default 16M in imx6_common to 64M.
--- include/configs/gw_ventana.h | 3 +++ 1 file changed, 3 insertions(+)
include/configs/gw_ventana.h +3 -0
@@ -38,6 +38,9 @@/* NAND */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 +#undef CONFIG_SYS_BOOTM_LEN +#define CONFIG_SYS_BOOTM_LEN (64 << 20) +/* I2C Configs */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC
Signature · 1 line
2.17.1
PATCH 3/11 imx: ventana: increase SYS_BOOTM_LEN
Quoted 2 lines
Increase
SYS_BOOM_LENfrom the default 16M inimx6_commonto 64M.Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 3/11 imx: ventana: increase SYS_BOOTM_LEN
In reply to Tim HarveyQuoted 2 lines
Increase
SYS_BOOM_LENfrom the default 16M inimx6_commonto 64M.Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 4/11 imx: ventana: add legacy uboot image support
In reply to Tim HarveyAdd Legacy U-Boot image support needed to boot a uImage.
--- configs/gwventana_emmc_defconfig | 1 - configs/gwventana_gw5904_defconfig | 1 - configs/gwventana_nand_defconfig | 1 - 3 files changed, 3 deletions(-)
configs/gwventana_emmc_defconfig +0 -1
@@ -24,7 +24,6 @@ CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set -# CONFIG_LEGACY_IMAGE_FORMAT is not set CONFIG_SUPPORT_RAW_INITRD=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
configs/gwventana_gw5904_defconfig +0 -1
@@ -24,7 +24,6 @@ CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set -# CONFIG_LEGACY_IMAGE_FORMAT is not set CONFIG_SUPPORT_RAW_INITRD=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
configs/gwventana_nand_defconfig +0 -1
@@ -24,7 +24,6 @@ CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_SPL_LOAD_FIT=y # CONFIG_USE_SPL_FIT_GENERATOR is not set -# CONFIG_LEGACY_IMAGE_FORMAT is not set CONFIG_SUPPORT_RAW_INITRD=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
Signature · 1 line
2.17.1
PATCH 4/11 imx: ventana: add legacy uboot image support
Quoted 2 lines
Add Legacy U-Boot image support needed to boot a uImage.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 4/11 imx: ventana: add legacy uboot image support
In reply to Tim HarveyQuoted 2 lines
Add Legacy U-Boot image support needed to boot a uImage.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 5/11 imx: ventana: add PMIC fix for GW54xx-G
In reply to Tim HarveySubstitutions in EOL parts changes the VDD_2P5 voltage rail such that the previously unused VGEN6 LDO is needed in place of the lower power VGEN5 for the GW54xx-G.
--- board/gateworks/gw_ventana/common.c | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)
board/gateworks/gw_ventana/common.c +22 -0
@@ -1550,6 +1550,17 @@ void setup_pmic(void)int board =read_eeprom (CONFIG_I2C_GSC , &ventana_info);const int i2c_pmic =1 ;u32 reg; +char rev; +int i; + +/* determine board revision */ + rev ='A' ; +for (i =sizeof (ventana_info.model) -1 ; i >0 ; i--) { +if (ventana_info.model[i] >='A' ) { + rev = ventana_info.model[i]; +break ; + } + }i2c_set_bus_num (i2c_pmic);
@@ -1573,6 +1584,17 @@ void setup_pmic(void) reg &= ~(SWBST_MODE_MASK |SWBST_VOL_MASK ); reg |= (SWBST_5_00V | (SWBST_MODE_AUTO <<SWBST_MODE_SHIFT ));pmic_reg_write (p,PFUZE100_SWBSTCON1 , reg); + +if (board == GW54xx && (rev =='G' )) { +/* Disable VGEN5 */ +pmic_reg_write (p,PFUZE100_VGEN5VOL ,0 ); + +/* Set VGEN6 to 2.5V and enable */ +pmic_reg_read (p,PFUZE100_VGEN6VOL , ®); + reg &= ~(LDO_VOL_MASK ); + reg |= (LDOB_2_50V |LDO_EN ); +pmic_reg_write (p,PFUZE100_VGEN6VOL , reg); + } } }
Signature · 1 line
2.17.1
PATCH 5/11 imx: ventana: add PMIC fix for GW54xx-G
Quoted 4 lines
Substitutions in EOL parts changes the
VDD_2P5voltage rail such that the previously unused VGEN6 LDO is needed in place of the lower power VGEN5 for the GW54xx-G.Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 5/11 imx: ventana: add PMIC fix for GW54xx-G
In reply to Tim HarveyQuoted 4 lines
Substitutions in EOL parts changes the
VDD_2P5voltage rail such that the previously unused VGEN6 LDO is needed in place of the lower power VGEN5 for the GW54xx-G.Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 6/11 imx: ventana: put PFUZ100 regulators in continuous mode
In reply to Tim HarveyIn the default 'auto' mode regulators that are very lightly loaded can be put in PFM mode and fail to regulator properly. Switching them to always use continuous PWM mode has a neglibable affect on system power and garuntees proper regulation under lightly loaded circumstances.
--- board/gateworks/gw_ventana/common.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)
board/gateworks/gw_ventana/common.c +26 -0
@@ -1596,6 +1596,32 @@ void setup_pmic(void)pmic_reg_write (p,PFUZE100_VGEN6VOL , reg); } } + +/* put all switchers in continuous mode */ +pmic_reg_read (p,PFUZE100_SW1ABMODE , ®); + reg &= ~(SW_MODE_MASK ); + reg |=PWM_PWM ; +pmic_reg_write (p,PFUZE100_SW1ABMODE , reg); + +pmic_reg_read (p,PFUZE100_SW2MODE , ®); + reg &= ~(SW_MODE_MASK ); + reg |=PWM_PWM ; +pmic_reg_write (p,PFUZE100_SW2MODE , reg); + +pmic_reg_read (p,PFUZE100_SW3AMODE , ®); + reg &= ~(SW_MODE_MASK ); + reg |=PWM_PWM ; +pmic_reg_write (p,PFUZE100_SW3AMODE , reg); + +pmic_reg_read (p,PFUZE100_SW3BMODE , ®); + reg &= ~(SW_MODE_MASK ); + reg |=PWM_PWM ; +pmic_reg_write (p,PFUZE100_SW3BMODE , reg); + +pmic_reg_read (p,PFUZE100_SW4MODE , ®); + reg &= ~(SW_MODE_MASK ); + reg |=PWM_PWM ; +pmic_reg_write (p,PFUZE100_SW4MODE , reg); }/* configure LTC3676 PMIC */
Signature · 1 line
2.17.1
PATCH 6/11 imx: ventana: put PFUZ100 regulators in continuous mode
Quoted 5 lines
In the default 'auto' mode regulators that are very lightly loaded can be put in PFM mode and fail to regulator properly. Switching them to always use continuous PWM mode has a neglibable affect on system power and garuntees proper regulation under lightly loaded circumstances.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 6/11 imx: ventana: put PFUZ100 regulators in continuous mode
In reply to Tim HarveyQuoted 5 lines
In the default 'auto' mode regulators that are very lightly loaded can be put in PFM mode and fail to regulator properly. Switching them to always use continuous PWM mode has a neglibable affect on system power and garuntees proper regulation under lightly loaded circumstances.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 7/11 imx: ventana: put LTC3676 regulators in continuous mode
In reply to Tim HarveyIn the default pulse-skipping mode regulators that are very lightly loaded can fail to regulate properly. Switching them to always use continuous mode causes only around 10mW of overall system power difference in a lightly loaded system that isn't already operating them in continuous mode.
--- board/gateworks/gw_ventana/common.c | 6 ++++++ 1 file changed, 6 insertions(+)
board/gateworks/gw_ventana/common.c +6 -0
@@ -1688,6 +1688,12 @@ void setup_pmic(void)/* set SW3 (VDD_ARM) */ pmic_reg_write (p,LTC3676_DVB3A ,0x1f ); } + +/* put all switchers in continuous mode */ +pmic_reg_write (p,LTC3676_BUCK1 ,0xc0 ); +pmic_reg_write (p,LTC3676_BUCK2 ,0xc0 ); +pmic_reg_write (p,LTC3676_BUCK3 ,0xc0 ); +pmic_reg_write (p,LTC3676_BUCK4 ,0xc0 ); } }
Signature · 1 line
2.17.1
PATCH 7/11 imx: ventana: put LTC3676 regulators in continuous mode
Quoted 6 lines
In the default pulse-skipping mode regulators that are very lightly loaded can fail to regulate properly. Switching them to always use continuous mode causes only around 10mW of overall system power difference in a lightly loaded system that isn't already operating them in continuous mode.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 7/11 imx: ventana: put LTC3676 regulators in continuous mode
In reply to Tim HarveyQuoted 6 lines
In the default pulse-skipping mode regulators that are very lightly loaded can fail to regulate properly. Switching them to always use continuous mode causes only around 10mW of overall system power difference in a lightly loaded system that isn't already operating them in continuous mode.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 8/11 imx: ventana: add DP83867 PHY LED configuration
In reply to Tim HarveyAdd DP83867 PHY LED configuration.
--- board/gateworks/gw_ventana/gw_ventana.c | 6 ++++++ 1 file changed, 6 insertions(+)
board/gateworks/gw_ventana/gw_ventana.c +6 -0
@@ -96,6 +96,12 @@ int board_phy_config(struct phy_device *phydev)/* TI DP83867 */ else if (phydev->phy_id == 0x2000a231) { +/* LED configuration */ + val =0 ; + val |=0x5 <<4 ;/* LED1(Amber;Speed) : 1000BT link */ + val |=0xb <<8 ;/* LED2(Green;Link/Act): blink for TX/RX act */ +phy_write (phydev,MDIO_DEVAD_NONE ,24 , val); +/* configure register 0x170 for ref CLKOUT */ phy_write (phydev,MDIO_DEVAD_NONE ,13 ,0x001f );phy_write (phydev,MDIO_DEVAD_NONE ,14 ,0x0170 );
Signature · 1 line
2.17.1
PATCH 8/11 imx: ventana: add DP83867 PHY LED configuration
Quoted 2 lines
Add DP83867 PHY LED configuration.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 8/11 imx: ventana: add DP83867 PHY LED configuration
In reply to Tim HarveyQuoted 2 lines
Add DP83867 PHY LED configuration.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 9/11 imx: ventana: display neteowrk PHY
In reply to Tim HarveyAdd displaying the detected network PHY on boot.
--- board/gateworks/gw_ventana/gw_ventana.c | 2 ++ 1 file changed, 2 insertions(+)
board/gateworks/gw_ventana/gw_ventana.c +2 -0
@@ -81,6 +81,7 @@ int board_phy_config(struct phy_device *phydev)/* Marvel 88E1510 */ if (phydev->phy_id ==0x1410dd1 ) { +puts ("MV88E1510" );/* * Page 3, Register 16: LED[2:0] Function Control Register * LED[0] (SPD:Amber) R16_3.3:0 to 0111: on-GbE link
@@ -96,6 +97,7 @@ int board_phy_config(struct phy_device *phydev)/* TI DP83867 */ else if (phydev->phy_id == 0x2000a231) { +puts ("TIDP83867 " );/* LED configuration */ val =0 ; val |=0x5 <<4 ;/* LED1(Amber;Speed) : 1000BT link */
Signature · 1 line
2.17.1
PATCH 9/11 imx: ventana: display neteowrk PHY
Quoted 2 lines
Add displaying the detected network PHY on boot.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 9/11 imx: ventana: display neteowrk PHY
In reply to Tim HarveyQuoted 2 lines
Add displaying the detected network PHY on boot.
Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 10/11 imx: ventana: add support for DLC0700XDP21LF LCD display
In reply to Tim HarveyAdd LVDS support for DLC0700XDP21LF 7in 1024x600 display (equivalent to the DLC-700JMGT4 with new touch controller)
--- board/gateworks/gw_ventana/gw_ventana.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)
board/gateworks/gw_ventana/gw_ventana.c +21 -0
@@ -245,6 +245,27 @@ struct display_info_t const displays[] = {{ .vsync_len = 10, .sync = FB_SYNC_EXT, .vmode = FB_VMODE_NONINTERLACED +} }, { +/* DLC0700XDP21LF-C-1 */ + .bus = 0, + .addr = 0, + .detect = NULL, + .enable = enable_lvds, + .pixfmt = IPU_PIX_FMT_LVDS666, + .mode = { + .name = "DLC0700XDP21LF", + .refresh = 60, + .xres = 1024, /* 1024x600active pixels */ + .yres = 600, + .pixclock = 15385, /* 64MHz */ + .left_margin = 220, + .right_margin = 40, + .upper_margin = 21, + .lower_margin = 7, + .hsync_len = 60, + .vsync_len = 10, + .sync = FB_SYNC_EXT, + .vmode =FB_VMODE_NONINTERLACED } }, {/* DLC800FIG-T-3 */ .bus = 2,
Signature · 1 line
2.17.1
PATCH 10/11 imx: ventana: add support for DLC0700XDP21LF LCD display
Quoted 4 lines
Add LVDS support for DLC0700XDP21LF 7in 1024x600 display (equivalent to the DLC-700JMGT4 with new touch controller)
Signed-off-by Robert Jones <[email protected]>Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 10/11 imx: ventana: add support for DLC0700XDP21LF LCD display
In reply to Tim HarveyQuoted 4 lines
Add LVDS support for DLC0700XDP21LF 7in 1024x600 display (equivalent to the DLC-700JMGT4 with new touch controller)
Signed-off-by Robert Jones <[email protected]>Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 11/11 imx: ventana: display 'none' for MMC if board does not have it
In reply to Tim Harveyprint 'None' instead of just a blank line if nothing is detected:
MMC: None
--- board/gateworks/gw_ventana/common.c | 1 + 1 file changed, 1 insertion(+)
board/gateworks/gw_ventana/common.c +1 -0
@@ -1758,6 +1758,7 @@ int board_mmc_init(struct bd_info *bis)return fsl_esdhc_initialize (bis, &usdhc_cfg[0 ]);default :/* doesn't have MMC */ +printf ("None" );return -1 ; } }
Signature · 1 line
2.17.1
PATCH 11/11 imx: ventana: display 'none' for MMC if board does not have it
Quoted 3 lines
print 'None' instead of just a blank line if nothing is detected:
MMC: NoneSigned-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 11/11 imx: ventana: display 'none' for MMC if board does not have it
In reply to Tim HarveyQuoted 3 lines
print 'None' instead of just a blank line if nothing is detected:
MMC: NoneSigned-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 1/11 imx: ventana: remove USB_KEYBOARD support
In reply to Tim HarveyQuoted 4 lines
For some time now having
USB_KEYBOARDsupport has caused usb to be initialized on boot. To allow for a quicker bootup we don't want this for Ventana and don't really need USB keyboard support so remove it.Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 1/11 imx: ventana: remove USB_KEYBOARD support
In reply to Tim HarveyQuoted 4 lines
For some time now having
USB_KEYBOARDsupport has caused usb to be initialized on boot. To allow for a quicker bootup we don't want this for Ventana and don't really need USB keyboard support so remove it.Signed-off-by Tim Harvey <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================