Skip to contentSkip to conversation

dt-bindings: PCI: ftpci100: convert faraday,ftpci100 to YAML

PATCH Applied Corentin Labbe 2 participants 2 messages Jun 28, 2021 – Jul 14, 2021

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 dt-bindings: PCI: ftpci100: convert faraday,ftpci100 to YAML

Converts pci/faraday,ftpci100.txt to yaml.
Some change are also made:
- example has wrong interrupts place

---
Changes since v1:
- fixed issues reported by Rob Herring https://patchwork.kernel.org/project/linux-pci/patch/[email protected]/
- moved comment as asked by Linus Walleij

Changes since v2:
- fixed issues reported by Rob Herring https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/

 .../bindings/pci/faraday,ftpci100.txt         | 135 --------------
 .../bindings/pci/faraday,ftpci100.yaml        | 176 ++++++++++++++++++
 2 files changed, 176 insertions(+), 135 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pci/faraday,ftpci100.txt
 create mode 100644 Documentation/devicetree/bindings/pci/faraday,ftpci100.yaml
Documentation/devicetree/bindings/pci/faraday,ftpci100.txt deleted +0 -135
deleted file mode 100644
index 5f8cb4962f8d..000000000000
@@ -1,135 +0,0 @@
-Faraday Technology FTPCI100 PCI Host Bridge
-
-This PCI bridge is found inside that Cortina Systems Gemini SoC platform and
-is a generic IP block from Faraday Technology. It exists in two variants:
-plain and dual PCI. The plain version embeds a cascading interrupt controller
-into the host bridge. The dual version routes the interrupts to the host
-chips interrupt controller.
-
-The host controller appear on the PCI bus with vendor ID 0x159b (Faraday
-Technology) and product ID 0x4321.
-
-Mandatory properties:
-
-- compatible: ranging from specific to generic, should be one of
-  "cortina,gemini-pci", "faraday,ftpci100"
-  "cortina,gemini-pci-dual", "faraday,ftpci100-dual"
-  "faraday,ftpci100"
-  "faraday,ftpci100-dual"
-- reg: memory base and size for the host bridge
-- #address-cells: set to <3>
-- #size-cells: set to <2>
-- #interrupt-cells: set to <1>
-- bus-range: set to <0x00 0xff>
-- device_type, set to "pci"
-- ranges: see pci.txt
-- interrupt-map-mask: see pci.txt
-- interrupt-map: see pci.txt
-- dma-ranges: three ranges for the inbound memory region. The ranges must
-  be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB,
-  128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as
-  pre-fetchable.
-
-Optional properties:
-- clocks: when present, this should contain the peripheral clock (PCLK) and the
-  PCI clock (PCICLK). If these are not present, they are assumed to be
-  hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz.
-- clock-names: when present, this should contain "PCLK" for the peripheral
-  clock and "PCICLK" for the PCI-side clock.
-
-Mandatory subnodes:
-- For "faraday,ftpci100" a node representing the interrupt-controller inside the
-  host bridge is mandatory. It has the following mandatory properties:
-  - interrupt: see interrupt-controller/interrupts.txt
-  - interrupt-controller: see interrupt-controller/interrupts.txt
-  - #address-cells: set to <0>
-  - #interrupt-cells: set to <1>
-
-I/O space considerations:
-
-The plain variant has 128MiB of non-prefetchable memory space, whereas the
-"dual" variant has 64MiB. Take this into account when describing the ranges.
-
-Interrupt map considerations:
-
-The "dual" variant will get INT A, B, C, D from the system interrupt controller
-and should point to respective interrupt in that controller in its
-interrupt-map.
-
-The code which is the only documentation of how the Faraday PCI (the non-dual
-variant) interrupts assigns the default interrupt mapping/swizzling has
-typically been like this, doing the swizzling on the interrupt controller side
-rather than in the interconnect:
-
-interrupt-map-mask = <0xf800 0 0 7>;
-interrupt-map =
-	<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
-	<0x4800 0 0 2 &pci_intc 1>,
-	<0x4800 0 0 3 &pci_intc 2>,
-	<0x4800 0 0 4 &pci_intc 3>,
-	<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
-	<0x5000 0 0 2 &pci_intc 2>,
-	<0x5000 0 0 3 &pci_intc 3>,
-	<0x5000 0 0 4 &pci_intc 0>,
-	<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
-	<0x5800 0 0 2 &pci_intc 3>,
-	<0x5800 0 0 3 &pci_intc 0>,
-	<0x5800 0 0 4 &pci_intc 1>,
-	<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
-	<0x6000 0 0 2 &pci_intc 0>,
-	<0x6000 0 0 3 &pci_intc 1>,
-	<0x6000 0 0 4 &pci_intc 2>;
-
-Example:
-
-pci@50000000 {
-	compatible = "cortina,gemini-pci", "faraday,ftpci100";
-	reg = <0x50000000 0x100>;
-	interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */
-			<26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */
-			<27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */
-			<28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */
-	#address-cells = <3>;
-	#size-cells = <2>;
-	#interrupt-cells = <1>;
-
-	bus-range = <0x00 0xff>;
-	ranges = /* 1MiB I/O space 0x50000000-0x500fffff */
-		 <0x01000000 0 0          0x50000000 0 0x00100000>,
-		 /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
-		 <0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
-
-	/* DMA ranges */
-	dma-ranges =
-	/* 128MiB at 0x00000000-0x07ffffff */
-	<0x02000000 0 0x00000000 0x00000000 0 0x08000000>,
-	/* 64MiB at 0x00000000-0x03ffffff */
-	<0x02000000 0 0x00000000 0x00000000 0 0x04000000>,
-	/* 64MiB at 0x00000000-0x03ffffff */
-	<0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
-
-	interrupt-map-mask = <0xf800 0 0 7>;
-	interrupt-map =
-		<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
-		<0x4800 0 0 2 &pci_intc 1>,
-		<0x4800 0 0 3 &pci_intc 2>,
-		<0x4800 0 0 4 &pci_intc 3>,
-		<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
-		<0x5000 0 0 2 &pci_intc 2>,
-		<0x5000 0 0 3 &pci_intc 3>,
-		<0x5000 0 0 4 &pci_intc 0>,
-		<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
-		<0x5800 0 0 2 &pci_intc 3>,
-		<0x5800 0 0 3 &pci_intc 0>,
-		<0x5800 0 0 4 &pci_intc 1>,
-		<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
-		<0x6000 0 0 2 &pci_intc 0>,
-		<0x6000 0 0 3 &pci_intc 0>,
-		<0x6000 0 0 4 &pci_intc 0>;
-	pci_intc: interrupt-controller {
-		interrupt-parent = <&intcon>;
-		interrupt-controller;
-		#address-cells = <0>;
-		#interrupt-cells = <1>;
-	};
-};
Documentation/devicetree/bindings/pci/faraday,ftpci100.yaml new file +176 -0

176 lines not on this page · raw message

Signature · 1 line
2.31.1
maintainer Applied
#1 lore raw
Quoted 11 lines · Corentin Labbe

Converts pci/faraday,ftpci100.txt to yaml.
Some change are also made:
- example has wrong interrupts place

---
Changes since v1:
- fixed issues reported by Rob Herring https://patchwork.kernel.org/project/linux-pci/patch/[email protected]/
- moved comment as asked by Linus Walleij

Quoted 9 lines

Changes since v2:
- fixed issues reported by Rob Herring https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/

 .../bindings/pci/faraday,ftpci100.txt         | 135 --------------
 .../bindings/pci/faraday,ftpci100.yaml        | 176 ++++++++++++++++++
 2 files changed, 176 insertions(+), 135 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pci/faraday,ftpci100.txt
 create mode 100644 Documentation/devicetree/bindings/pci/faraday,ftpci100.yaml

Applied, thanks!