New V4L2 controls V4L2_CID_NOTIFY_GAIN_XXX
v3 cover New V4L2 controls V4L2_CID_NOTIFY_GAIN_XXX
Hi
Sorry for the delay with these patches, I think my previous attempt didn't cast the email net wide enough and they got rather lost - my apologies!
Anyway, this version addresses the feedback I had received originally, so thank you for that. Therefore:
* The values are now specified to be linear gains.
* The default value is defined to be the value that is equivalent to a gain of 1x.
* I think there was a minor comment over the repetitiveness of the documentation, so I've tried to address that too.
Thanks very much and best regards
David
David Plowman (2):
media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
media: v4l2-ctrls: Document V4L2_CID_NOTIFY_GAIN_XXX controls
.../media/v4l/ext-ctrls-image-source.rst | 25 +++++++++++++++++++ drivers/media/v4l2-core/v4l2-ctrls-defs.c | 4 +++ include/uapi/linux/v4l2-controls.h | 4 +++ 3 files changed, 33 insertions(+)
Signature · 1 line
2.30.2
PATCH v3 1/2 media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
We add new controls, one for each of the four usual Bayer channels:
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENB
These are provided for sensors that need to know what colour gains will be applied to the Bayer channel by subsequent processing (such as by an ISP), even though the sensor will not apply this gain itself.
The units are linear with the default value indicating a gain of exactly 1.
--- drivers/media/v4l2-core/v4l2-ctrls-defs.c | 4 ++++ include/uapi/linux/v4l2-controls.h | 4 ++++ 2 files changed, 8 insertions(+)
drivers/media/v4l2-core/v4l2-ctrls-defs.c +4 -0
@@ -1106,6 +1106,10 @@ const char *v4l2_ctrl_get_name(u32 id)case V4L2_CID_TEST_PATTERN_GREENR :return "Green (Red) Pixel Value" ;case V4L2_CID_TEST_PATTERN_BLUE :return "Blue Pixel Value" ;case V4L2_CID_TEST_PATTERN_GREENB :return "Green (Blue) Pixel Value" ; +case V4L2_CID_NOTIFY_GAIN_RED :return "Notify Red Gain" ; +case V4L2_CID_NOTIFY_GAIN_GREENR :return "Notify Green (Red) Gain" ; +case V4L2_CID_NOTIFY_GAIN_BLUE :return "Notify Blue Gain" ; +case V4L2_CID_NOTIFY_GAIN_GREENB :return "Notify Green (Blue) Gain" ;/* Image processing controls */ /* Keep the order of the 'case's the same as in v4l2-controls.h! */
include/uapi/linux/v4l2-controls.h +4 -0
@@ -1117,6 +1117,10 @@ enum v4l2_jpeg_chroma_subsampling {#define V4L2_CID_TEST_PATTERN_BLUE (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 6)#define V4L2_CID_TEST_PATTERN_GREENB (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 7)#define V4L2_CID_UNIT_CELL_SIZE (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 8) +#define V4L2_CID_NOTIFY_GAIN_RED (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 9) +#define V4L2_CID_NOTIFY_GAIN_GREENR (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 10) +#define V4L2_CID_NOTIFY_GAIN_BLUE (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 11) +#define V4L2_CID_NOTIFY_GAIN_GREENB (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 12)/* Image processing controls */
Signature · 1 line
2.30.2
Re: [PATCH v3 1/2] media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
Quoted 7 lines · David Plowman
We add new controls, one for each of the four usual Bayer channels:
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENB
Quoted 8 lines
These are provided for sensors that need to know what colour gains will be applied to the Bayer channel by subsequent processing (such as by an ISP), even though the sensor will not apply this gain itself.
The units are linear with the default value indicating a gain of exactly 1.
Signed-off-by David Plowman <[email protected]>
Regards,
Hans
Quoted 36 lines
--- drivers/media/v4l2-core/v4l2-ctrls-defs.c | 4 ++++ include/uapi/linux/v4l2-controls.h | 4 ++++ 2 files changed, 8 insertions(+)drivers/media/v4l2-core/v4l2-ctrls-defs.c +4
-0@@ -1106,6 +1106,10 @@ const char *v4l2_ctrl_get_name(u32 id)case V4L2_CID_TEST_PATTERN_GREENR :return "Green (Red) Pixel Value" ;case V4L2_CID_TEST_PATTERN_BLUE :return "Blue Pixel Value" ;case V4L2_CID_TEST_PATTERN_GREENB :return "Green (Blue) Pixel Value" ; +case V4L2_CID_NOTIFY_GAIN_RED :return "Notify Red Gain" ; +case V4L2_CID_NOTIFY_GAIN_GREENR :return "Notify Green (Red) Gain" ; +case V4L2_CID_NOTIFY_GAIN_BLUE :return "Notify Blue Gain" ; +case V4L2_CID_NOTIFY_GAIN_GREENB :return "Notify Green (Blue) Gain" ;/* Image processing controls */ /* Keep the order of the 'case's the same as in v4l2-controls.h! */ include/uapi/linux/v4l2-controls.h +4
-0@@ -1117,6 +1117,10 @@ enum v4l2_jpeg_chroma_subsampling {#define V4L2_CID_TEST_PATTERN_BLUE (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 6)#define V4L2_CID_TEST_PATTERN_GREENB (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 7)#define V4L2_CID_UNIT_CELL_SIZE (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 8) +#define V4L2_CID_NOTIFY_GAIN_RED (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 9) +#define V4L2_CID_NOTIFY_GAIN_GREENR (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 10) +#define V4L2_CID_NOTIFY_GAIN_BLUE (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 11) +#define V4L2_CID_NOTIFY_GAIN_GREENB (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 12)/* Image processing controls */
Re: [PATCH v3 1/2] media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
In reply to David PlowmanHi David,
Thank you for the patch.
Quoted 6 lines · David Plowman
We add new controls, one for each of the four usual Bayer channels:
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENB
This will effectively limit the API to Bayer patterns. I wonder if we should instead implement it as a single array control, with one element per CFA component.
Quoted 43 lines
These are provided for sensors that need to know what colour gains will be applied to the Bayer channel by subsequent processing (such as by an ISP), even though the sensor will not apply this gain itself.
The units are linear with the default value indicating a gain of exactly 1.
Signed-off-by David Plowman <[email protected]>--- drivers/media/v4l2-core/v4l2-ctrls-defs.c | 4 ++++ include/uapi/linux/v4l2-controls.h | 4 ++++ 2 files changed, 8 insertions(+)drivers/media/v4l2-core/v4l2-ctrls-defs.c +4
-0@@ -1106,6 +1106,10 @@ const char *v4l2_ctrl_get_name(u32 id)case V4L2_CID_TEST_PATTERN_GREENR :return "Green (Red) Pixel Value" ;case V4L2_CID_TEST_PATTERN_BLUE :return "Blue Pixel Value" ;case V4L2_CID_TEST_PATTERN_GREENB :return "Green (Blue) Pixel Value" ; +case V4L2_CID_NOTIFY_GAIN_RED :return "Notify Red Gain" ; +case V4L2_CID_NOTIFY_GAIN_GREENR :return "Notify Green (Red) Gain" ; +case V4L2_CID_NOTIFY_GAIN_BLUE :return "Notify Blue Gain" ; +case V4L2_CID_NOTIFY_GAIN_GREENB :return "Notify Green (Blue) Gain" ;/* Image processing controls */ /* Keep the order of the 'case's the same as in v4l2-controls.h! */ include/uapi/linux/v4l2-controls.h +4
-0@@ -1117,6 +1117,10 @@ enum v4l2_jpeg_chroma_subsampling {#define V4L2_CID_TEST_PATTERN_BLUE (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 6)#define V4L2_CID_TEST_PATTERN_GREENB (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 7)#define V4L2_CID_UNIT_CELL_SIZE (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 8) +#define V4L2_CID_NOTIFY_GAIN_RED (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 9) +#define V4L2_CID_NOTIFY_GAIN_GREENR (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 10) +#define V4L2_CID_NOTIFY_GAIN_BLUE (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 11) +#define V4L2_CID_NOTIFY_GAIN_GREENB (V4L2_CID_IMAGE_SOURCE_CLASS_BASE + 12)/* Image processing controls */
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH v3 1/2] media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
Hi David, Laurent,
Quoted 7 lines · Laurent Pinchart
Hi David,
Thank you for the patch.
Quoted 2 lines · David Plowman
We add new controls, one for each of the four usual Bayer channels:
Quoted 8 lines
Quoted 4 lines
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENBThis will effectively limit the API to Bayer patterns. I wonder if we should instead implement it as a single array control, with one element per CFA component.
There are other raw patterns, too. Supporting them would likely require one or a few more controls.
That said, as the values change often it's more efficient to use a single control. But each colour combination (not each pattern) would require its own control in this case, eventually requiring more controls.
Given that the number of sensors using non-Bayer patterns but still produce Bayer output is likely to grow, these could be used by a number of devices. I'd hence prefer an array control as well.
Signature · 3 lines
Kind regards, Sakari Ailus
Re: [PATCH v3 1/2] media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
Hi Sakari,
Quoted 13 lines · Sakari Ailus
Quoted 11 lines · Laurent Pinchart
Quoted 6 lines · David Plowman
We add new controls, one for each of the four usual Bayer channels:
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENBThis will effectively limit the API to Bayer patterns. I wonder if we should instead implement it as a single array control, with one element per CFA component.
Quoted 6 lines
There are other raw patterns, too. Supporting them would likely require one or a few more controls.
That said, as the values change often it's more efficient to use a single control. But each colour combination (not each pattern) would require its own control in this case, eventually requiring more controls.
I'm not sure to follow you. My idea is to define a single control, with a number of elements that depends on the pattern being used, and the order specified in the native sensor pattern. I don't think each colour combination would then require its own control.
Quoted 3 lines
Given that the number of sensors using non-Bayer patterns but still produce Bayer output is likely to grow, these could be used by a number of devices. I'd hence prefer an array control as well.
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH v3 1/2] media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
Quoted 19 lines · Laurent Pinchart
Hi Sakari,
Quoted 16 lines · Sakari Ailus
Quoted 11 lines · Laurent Pinchart
Quoted 6 lines · David Plowman
We add new controls, one for each of the four usual Bayer channels:
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENBThis will effectively limit the API to Bayer patterns. I wonder if we should instead implement it as a single array control, with one element per CFA component.
There are other raw patterns, too. Supporting them would likely require one or a few more controls.
Quoted 8 lines
Quoted 3 lines
That said, as the values change often it's more efficient to use a single control. But each colour combination (not each pattern) would require its own control in this case, eventually requiring more controls.
I'm not sure to follow you. My idea is to define a single control, with a number of elements that depends on the pattern being used, and the order specified in the native sensor pattern. I don't think each colour combination would then require its own control.
Ah, I guess that would work, too. Then we'll need to define what kind of pixel orders are supported for that single control (and for which formats).
Signature · 1 line
Sakari Ailus
Re: [PATCH v3 1/2] media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
Hi Sakari, Laurent
Thanks for the various comments and discussion. It did prompt me to have some second thoughts about some of the details here, as follows.
These controls are aimed specifically at sensors that do some kind of on-board "demosaic / remosaic" process, for instance to produce standard Bayer patterns from non-standard ones. As such the principal requirement is for the sensor to know what "grey" looks like, which we tell it by sending it the red and blue gains from the white balance algorithm. (This obviously enables it to reduce colour aliasing during the processing that it does.)
So perhaps the comparison here should be with the existing V4L2_CID_RED/BLUE_BALANCE controls. I'm not sure that it really matters exactly what the colours of the pixels on the sensor really are, it's knowing what "grey" looks like that is important. Any new controls could be quite cumbersome to use if you have to figure out what the underlying pixel arrangement looks like, it certainly feels much easier to refer simply to red/blue pixels, leaving the driver to deal with its own internal idiosyncrasies.
Having said that, the particular sensor I have exposes a gain for each of the four Bayer channels, even though I find myself ignoring the green ones!!
Anyway, I certainly feel I could go either way on this one - do you have any more thoughts on the matter?
Thanks and best regards
David
Quoted 35 lines · Sakari Ailus
Quoted 19 lines · Laurent Pinchart
Hi Sakari,
Quoted 16 lines · Sakari Ailus
Quoted 11 lines · Laurent Pinchart
Quoted 6 lines · David Plowman
We add new controls, one for each of the four usual Bayer channels:
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENBThis will effectively limit the API to Bayer patterns. I wonder if we should instead implement it as a single array control, with one element per CFA component.
There are other raw patterns, too. Supporting them would likely require one or a few more controls.
Quoted 8 lines
Quoted 3 lines
That said, as the values change often it's more efficient to use a single control. But each colour combination (not each pattern) would require its own control in this case, eventually requiring more controls.
I'm not sure to follow you. My idea is to define a single control, with a number of elements that depends on the pattern being used, and the order specified in the native sensor pattern. I don't think each colour combination would then require its own control.
Ah, I guess that would work, too. Then we'll need to define what kind of pixel orders are supported for that single control (and for which formats).
--
Sakari Ailus
Re: [PATCH v3 1/2] media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
Hi David,
Quoted 13 lines · David Plowman
Hi Sakari, Laurent
Thanks for the various comments and discussion. It did prompt me to have some second thoughts about some of the details here, as follows.
These controls are aimed specifically at sensors that do some kind of on-board "demosaic / remosaic" process, for instance to produce standard Bayer patterns from non-standard ones. As such the principal requirement is for the sensor to know what "grey" looks like, which we tell it by sending it the red and blue gains from the white balance algorithm. (This obviously enables it to reduce colour aliasing during the processing that it does.)
Quoted 8 lines
So perhaps the comparison here should be with the existing V4L2_CID_RED/BLUE_BALANCE controls. I'm not sure that it really matters exactly what the colours of the pixels on the sensor really are, it's knowing what "grey" looks like that is important. Any new controls could be quite cumbersome to use if you have to figure out what the underlying pixel arrangement looks like, it certainly feels much easier to refer simply to red/blue pixels, leaving the driver to deal with its own internal idiosyncrasies.
I think I missed these are the gains of the Bayer pattern components, and by definition you'll be only setting the gains of those components that are sent out by the sensor. So there wouldn't be other components around, just these four.
Quoted 7 lines
Having said that, the particular sensor I have exposes a gain for each of the four Bayer channels, even though I find myself ignoring the green ones!!
Anyway, I certainly feel I could go either way on this one - do you have any more thoughts on the matter?
I'm leaning towards a single array control with specified, mbus code independent order of components. You should add this control is applicable to Bayer pattern output only. That leaves it easily extendable later on.
Signature · 3 lines
Kind regards, Sakari Ailus
Re: [PATCH v3 1/2] media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
In reply to David PlowmanHi David,
Quoted 22 lines · David Plowman
Hi Sakari, Laurent
Thanks for the various comments and discussion. It did prompt me to have some second thoughts about some of the details here, as follows.
These controls are aimed specifically at sensors that do some kind of on-board "demosaic / remosaic" process, for instance to produce standard Bayer patterns from non-standard ones. As such the principal requirement is for the sensor to know what "grey" looks like, which we tell it by sending it the red and blue gains from the white balance algorithm. (This obviously enables it to reduce colour aliasing during the processing that it does.)
So perhaps the comparison here should be with the existing V4L2_CID_RED/BLUE_BALANCE controls. I'm not sure that it really matters exactly what the colours of the pixels on the sensor really are, it's knowing what "grey" looks like that is important. Any new controls could be quite cumbersome to use if you have to figure out what the underlying pixel arrangement looks like, it certainly feels much easier to refer simply to red/blue pixels, leaving the driver to deal with its own internal idiosyncrasies.
Quoted 6 lines
Having said that, the particular sensor I have exposes a gain for each of the four Bayer channels, even though I find myself ignoring the green ones!!
Anyway, I certainly feel I could go either way on this one - do you have any more thoughts on the matter?
With an array control, we would have to decide (and document) which components are stored in the array, and in which order. For Bayer sensors, that would be B, Gb, Gr and R. As for the order, there are three options:
- fixed order (e.g. always B, Gb, Gr, R)
- matching the sensor's CFA native order (always the same for a given sensor, but varying between different sensors)
- matching the currently configured format (the bayer pattern can change when moving the crop rectangle by one pixels or when mirroring the sensor readout)
The last two options seem quite impractical to me. The first option, if we only consider Bayer sensors, is equivalent to the four controls your propose in the sense that the semantics is defined in the control specification and identical for all sensors, but with the advantage of bundling all four values together. It will also allow expanding this to other patterns if the need arise, which I think would be useful.
If we were to redesign the red/blue gains, I'd go for a single array control today, with one value per CFA component.
Quoted 30 lines · Sakari Ailus
Quoted 29 lines · Laurent Pinchart
Quoted 17 lines · Sakari Ailus
Quoted 16 lines · Laurent Pinchart
Quoted 11 lines · David Plowman
Quoted 6 lines
We add new controls, one for each of the four usual Bayer channels:
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENBThis will effectively limit the API to Bayer patterns. I wonder if we should instead implement it as a single array control, with one element per CFA component.
There are other raw patterns, too. Supporting them would likely require one or a few more controls.
Quoted 8 lines
Quoted 3 lines
That said, as the values change often it's more efficient to use a single control. But each colour combination (not each pattern) would require its own control in this case, eventually requiring more controls.
I'm not sure to follow you. My idea is to define a single control, with a number of elements that depends on the pattern being used, and the order specified in the native sensor pattern. I don't think each colour combination would then require its own control.
Ah, I guess that would work, too. Then we'll need to define what kind of pixel orders are supported for that single control (and for which formats).
Signature · 3 lines
Regards, Laurent Pinchart
Re: [PATCH v3 1/2] media: v4l2-ctrls: Add V4L2_CID_NOTIFY_GAIN_XXX controls
Hi Laurent
Thanks for the reply. Yes, I agree that a fixed order (B, Gb, Gr, R) is much easier to use, and I think that works well for the cases I'm dealing with. I'll update the patch set accordingly and re-post it.
Best regards
David
Quoted 90 lines · Laurent Pinchart
Hi David,
Quoted 22 lines · David Plowman
Hi Sakari, Laurent
Thanks for the various comments and discussion. It did prompt me to have some second thoughts about some of the details here, as follows.
These controls are aimed specifically at sensors that do some kind of on-board "demosaic / remosaic" process, for instance to produce standard Bayer patterns from non-standard ones. As such the principal requirement is for the sensor to know what "grey" looks like, which we tell it by sending it the red and blue gains from the white balance algorithm. (This obviously enables it to reduce colour aliasing during the processing that it does.)
So perhaps the comparison here should be with the existing V4L2_CID_RED/BLUE_BALANCE controls. I'm not sure that it really matters exactly what the colours of the pixels on the sensor really are, it's knowing what "grey" looks like that is important. Any new controls could be quite cumbersome to use if you have to figure out what the underlying pixel arrangement looks like, it certainly feels much easier to refer simply to red/blue pixels, leaving the driver to deal with its own internal idiosyncrasies.
Quoted 6 lines
Having said that, the particular sensor I have exposes a gain for each of the four Bayer channels, even though I find myself ignoring the green ones!!
Anyway, I certainly feel I could go either way on this one - do you have any more thoughts on the matter?
With an array control, we would have to decide (and document) which components are stored in the array, and in which order. For Bayer sensors, that would be B, Gb, Gr and R. As for the order, there are three options:
- fixed order (e.g. always B, Gb, Gr, R)
- matching the sensor's CFA native order (always the same for a given sensor, but varying between different sensors)
- matching the currently configured format (the bayer pattern can change when moving the crop rectangle by one pixels or when mirroring the sensor readout)The last two options seem quite impractical to me. The first option, if we only consider Bayer sensors, is equivalent to the four controls your propose in the sense that the semantics is defined in the control specification and identical for all sensors, but with the advantage of bundling all four values together. It will also allow expanding this to other patterns if the need arise, which I think would be useful.
If we were to redesign the red/blue gains, I'd go for a single array control today, with one value per CFA component.
Quoted 23 lines · Sakari Ailus
Quoted 22 lines · Laurent Pinchart
Quoted 21 lines · Sakari Ailus
Quoted 19 lines · Laurent Pinchart
Quoted 11 lines · David Plowman
Quoted 6 lines
We add new controls, one for each of the four usual Bayer channels:
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENBThis will effectively limit the API to Bayer patterns. I wonder if we should instead implement it as a single array control, with one element per CFA component.
There are other raw patterns, too. Supporting them would likely require one or a few more controls.
That said, as the values change often it's more efficient to use a single control. But each colour combination (not each pattern) would require its own control in this case, eventually requiring more controls.
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines
I'm not sure to follow you. My idea is to define a single control, with a number of elements that depends on the pattern being used, and the order specified in the native sensor pattern. I don't think each colour combination would then require its own control.
Ah, I guess that would work, too. Then we'll need to define what kind of pixel orders are supported for that single control (and for which formats).
--
Regards,Laurent Pinchart
PATCH v3 2/2 media: v4l2-ctrls: Document V4L2_CID_NOTIFY_GAIN_XXX controls
In reply to David PlowmanAdd documentation for each of the controls
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENB
These controls are required by sensors that need to know what colour gains will be applied to pixels by downstream processing (such as by an ISP), though the sensor does not apply these gains itself.
--- .../media/v4l/ext-ctrls-image-source.rst | 25 +++++++++++++++++++ 1 file changed, 25 insertions(+)
Documentation/userspace-api/media/v4l/ext-ctrls-image-source.rst +25 -0
@@ -72,3 +72,28 @@ Image Source Control IDs * - __u32 - ``height`` - Height of the area. + +``V4L2_CID_NOTIFY_GAIN_RED (integer)`` + Please refer to ``V4L2_CID_NOTIFY_GAIN_GREENB`` below. + +``V4L2_CID_NOTIFY_GAIN_GREENR (integer)`` + Please refer to ``V4L2_CID_NOTIFY_GAIN_GREENB`` below. + +``V4L2_CID_NOTIFY_GAIN_BLUE (integer)`` + Please refer to ``V4L2_CID_NOTIFY_GAIN_GREENB`` below. + +``V4L2_CID_NOTIFY_GAIN_GREENB (integer)`` + Note: this description covers all four ``V4L2_CID_NOTIFY_GAIN`` + controls, according to the Bayer channel indicated at the end of + the control name. + + The sensor is notified what gain will be applied to this Bayer + channel by subsequent processing (such as by an ISP). The sensor + is merely informed of this value in case it performs processing + that requires it, but it does not apply it to the output pixels + themselves. + + The units for the gain value are linear, with the default value + being shared between all four controls and representing a gain of + exactly 1. Other control properties, such as ranges, should also + be common.
Signature · 1 line
2.30.2
Re: [PATCH v3 2/2] media: v4l2-ctrls: Document V4L2_CID_NOTIFY_GAIN_XXX controls
Quoted 7 lines · David Plowman
Add documentation for each of the controls
V4L2_CID_NOTIFY_GAIN_REDV4L2_CID_NOTIFY_GAIN_GREENRV4L2_CID_NOTIFY_GAIN_BLUEV4L2_CID_NOTIFY_GAIN_GREENB
Quoted 5 lines
These controls are required by sensors that need to know what colour gains will be applied to pixels by downstream processing (such as by an ISP), though the sensor does not apply these gains itself.
Signed-off-by David Plowman <[email protected]>
Regards,
Hans
Quoted 38 lines
--- .../media/v4l/ext-ctrls-image-source.rst | 25 +++++++++++++++++++ 1 file changed, 25 insertions(+)Documentation/userspace-api/media/v4l/ext-ctrls-image-source.rst +25
-0@@ -72,3 +72,28 @@ Image Source Control IDs * - __u32 - ``height`` - Height of the area. + +``V4L2_CID_NOTIFY_GAIN_RED (integer)`` + Please refer to ``V4L2_CID_NOTIFY_GAIN_GREENB`` below. + +``V4L2_CID_NOTIFY_GAIN_GREENR (integer)`` + Please refer to ``V4L2_CID_NOTIFY_GAIN_GREENB`` below. + +``V4L2_CID_NOTIFY_GAIN_BLUE (integer)`` + Please refer to ``V4L2_CID_NOTIFY_GAIN_GREENB`` below. + +``V4L2_CID_NOTIFY_GAIN_GREENB (integer)`` + Note: this description covers all four ``V4L2_CID_NOTIFY_GAIN`` + controls, according to the Bayer channel indicated at the end of + the control name. + + The sensor is notified what gain will be applied to this Bayer + channel by subsequent processing (such as by an ISP). The sensor + is merely informed of this value in case it performs processing + that requires it, but it does not apply it to the output pixels + themselves. + + The units for the gain value are linear, with the default value + being shared between all four controls and representing a gain of + exactly 1. Other control properties, such as ranges, should also + be common.